problema connessione tiscali

[ambulanza]

Originariamente inviato da sacarde

- l'errore si riferisce a sda/swap (e' il disco principale?)


- eth1 sembra connesso (wireless)


devi trovare delle differenze tra il "prima" e il "dopo mezzora"

edito sopra, inserendo il "prima".
il disco principale (system) è "/" sda/swap nn so cosa sia O_o

[Pardo]

inet6 fe80::20e:35ff:fef4:7f48/64 scope link

Proverei anche a disattivare ipv6.

(io premetto che non ne conosco il funzionamento, ma mi e` capitato che bloccasse la rete con lunghi timeout)

[sacarde]

tra i dati postati...

[prima] e [dopo] ... io non ho trovato differenze



p.s.
riesci a accedere all'interfaccia http del router? e' collegato?

[ambulanza]

come faccio a disattivarlo?
ho trovato questo http://www.hwupgrade.it/forum/showthread.php?t=1481838 ma il mii problema è diverso perchè non ho pacchetti di ritorno

anche io analizzando i risultati non ho trovato nulla di diverso O_o. per quanto riguarda il router non so come accedervi, ma sicuro è collegato perchè dal computer della mia coinquilina funziona senza problemi...

[sacarde]

http://www.consulenti-ict.it/Area-Te...su-ubuntu.html

[ambulanza]

ipv6 disattivato... non cambia niente auf

[sacarde]

- ma ha sempre fatto questo problema?

- vuoi dire che lo stesso pc , in un'altra rete wifi, va bene subito?

- appena funziona, che vedi nei log:
dmesg
/var/log/messages

[ambulanza]

Originariamente inviato da sacarde

- ma ha sempre fatto questo problema?

- vuoi dire che lo stesso pc , in un'altra rete wifi, va bene subito?

- appena funziona, che vedi nei log:
dmesg
/var/log/messages

no in altre reti fa lo stesso problema. ad esempio ora sono in uni e con il wifi della scuola fa lo stesso problema.
questi i risultati:

dmesg


[ 0.231388] ERROR: Unable to locate IOAPIC for GSI 8
[ 0.231439] ERROR: Unable to locate IOAPIC for GSI 13
[ 0.232219] ERROR: Unable to locate IOAPIC for GSI 1
[ 0.232395] ERROR: Unable to locate IOAPIC for GSI 12
[ 0.253601] pnp: PnP ACPI: found 8 devices
[ 0.253604] ACPI: ACPI bus type pnp unregistered
[ 0.253610] PnPBIOS: Disabled by ACPI PNP
[ 0.253634] system 00:04: [io 0x0600-0x060f] has been reserved
[ 0.253638] system 00:04: [io 0x0700-0x070f] has been reserved
[ 0.253642] system 00:04: [io 0x0800-0x080f] has been reserved
[ 0.253646] system 00:04: [io 0x1000-0x107f] has been reserved
[ 0.253650] system 00:04: [io 0x1180-0x11bf] has been reserved
[ 0.253654] system 00:04: [io 0x01c0-0x01cf] has been reserved
[ 0.253659] system 00:04: [io 0xfe00] has been reserved
[ 0.253663] system 00:04: [io 0x04d0-0x04d1] has been reserved
[ 0.253667] system 00:04: [io 0x0610-0x061f] has been reserved
[ 0.253673] system 00:04: [mem 0xfec10000-0xfec1ffff] has been reserved
[ 0.253678] system 00:04: [mem 0xff800000-0xffbfffff] has been reserved
[ 0.253682] system 00:04: [mem 0xfff00000-0xffffffff] could not be reserved
[ 0.253687] system 00:04: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.253691] system 00:04: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.290318] pci 0000:00:1e.0: BAR 15: assigned [mem 0x50000000-0x53ffffff pref]
[ 0.290323] pci 0000:00:1f.1: BAR 5: assigned [mem 0x54000000-0x540003ff]
[ 0.290332] pci 0000:00:1f.1: BAR 5: set to [mem 0x54000000-0x540003ff] (PCI address [0x54000000-0x540003ff]
[ 0.290338] pci 0000:02:06.0: BAR 15: assigned [mem 0x50000000-0x53ffffff pref]
[ 0.290343] pci 0000:02:06.0: BAR 16: assigned [mem 0x58000000-0x5bffffff]
[ 0.290347] pci 0000:02:06.0: BAR 13: assigned [io 0x3400-0x34ff]
[ 0.290350] pci 0000:02:06.0: BAR 14: assigned [io 0x3800-0x38ff]
[ 0.290354] pci 0000:02:06.0: CardBus bridge to [bus 03-06]
[ 0.290358] pci 0000:02:06.0: bridge window [io 0x3400-0x34ff]
[ 0.290364] pci 0000:02:06.0: bridge window [io 0x3800-0x38ff]
[ 0.290369] pci 0000:02:06.0: bridge window [mem 0x50000000-0x53ffffff pref]
[ 0.290375] pci 0000:02:06.0: bridge window [mem 0x58000000-0x5bffffff]
[ 0.290381] pci 0000:00:1e.0: PCI bridge to [bus 02-02]
[ 0.290386] pci 0000:00:1e.0: bridge window [io 0x3000-0x3fff]
[ 0.290392] pci 0000:00:1e.0: bridge window [mem 0xe0200000-0xe05fffff]
[ 0.290398] pci 0000:00:1e.0: bridge window [mem 0x50000000-0x53ffffff pref]
[ 0.290416] pci 0000:00:1e.0: setting latency timer to 64
[ 0.290426] pci 0000:02:06.0: enabling device (0104 -> 0107)
[ 0.290649] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
[ 0.290654] PCI: setting IRQ 10 as level-triggered
[ 0.290660] pci 0000:02:06.0: PCI INT A -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
[ 0.290668] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.290671] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[ 0.290675] pci_bus 0000:02: resource 0 [io 0x3000-0x3fff]
[ 0.290679] pci_bus 0000:02: resource 1 [mem 0xe0200000-0xe05fffff]
[ 0.290683] pci_bus 0000:02: resource 2 [mem 0x50000000-0x53ffffff pref]
[ 0.290686] pci_bus 0000:02: resource 4 [io 0x0000-0xffff]
[ 0.290690] pci_bus 0000:02: resource 5 [mem 0x00000000-0xffffffff]
[ 0.290694] pci_bus 0000:03: resource 0 [io 0x3400-0x34ff]
[ 0.290697] pci_bus 0000:03: resource 1 [io 0x3800-0x38ff]
[ 0.290701] pci_bus 0000:03: resource 2 [mem 0x50000000-0x53ffffff pref]
[ 0.290704] pci_bus 0000:03: resource 3 [mem 0x58000000-0x5bffffff]
[ 0.290762] NET: Registered protocol family 2
[ 0.290845] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.291185] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.292598] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.293585] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.293590] TCP reno registered
[ 0.293600] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.293634] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.293821] NET: Registered protocol family 1
[ 0.293854] pci 0000:00:02.0: Boot video device
[ 0.293958] PCI: CLS 32 bytes, default 64
[ 0.294079] Simple Boot Flag at 0x37 set to 0x1
[ 0.294216] cpufreq-nforce2: No nForce2 chipset.
[ 0.294259] Scanning for low memory corruption every 60 seconds
[ 0.294419] audit: initializing netlink socket (disabled)
[ 0.294438] type=2000 audit(1300273135.292:1): initialized
[ 0.309841] Trying to unpack rootfs image as initramfs...
[ 0.326178] highmem bounce pool size: 64 pages
[ 0.326187] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.337701] VFS: Disk quotas dquot_6.5.2
[ 0.337800] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.338704] fuse init (API version 7.14)
[ 0.338832] msgmni has been set to 1703
[ 0.737702] Freeing initrd memory: 10520k freed
[ 0.751823] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.751830] io scheduler noop registered
[ 0.751833] io scheduler deadline registered
[ 0.751858] io scheduler cfq registered (default)
[ 0.752055] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.752086] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.765651] ACPI: AC Adapter [ACAD] (on-line)
[ 0.765751] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[ 0.781567] ACPI: Lid Switch [LID]
[ 0.781633] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[ 0.781640] ACPI: Sleep Button [SLPB]
[ 0.781705] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 0.781710] ACPI: Power Button [PWRF]
[ 0.781895] ACPI: Fan [FAN0] (off)
[ 0.782039] ACPI: Fan [FAN1] (off)
[ 0.782189] ACPI: acpi_idle registered with cpuidle
[ 0.782225] Marking TSC unstable due to TSC halts in idle
[ 0.784576] Switching to clocksource acpi_pm
[ 0.832201] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.832213] ACPI: Thermal Zone [THRM] (45 C)
[ 0.832366] ERST: Table is not found!
[ 0.832585] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.833037] serial 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
[ 0.833046] serial 0000:00:1f.6: PCI INT B disabled
[ 0.834601] brd: module loaded
[ 0.835344] loop: module loaded
[ 0.835594] ata_piix 0000:00:1f.1: version 2.13
[ 0.835604] ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
[ 0.835834] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[ 0.835840] ata_piix 0000:00:1f.1: PCI INT A -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
[ 0.835890] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 0.835994] isapnp: Scanning for PnP cards...
[ 1.015804] scsi0 : ata_piix
[ 1.015915] scsi1 : ata_piix
[ 1.015966] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
[ 1.015970] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
[ 1.016486] Fixed MDIO Bus: probed
[ 1.016534] PPP generic driver version 2.4.2
[ 1.016598] tun: Universal TUN/TAP device driver, 1.6
[ 1.016601] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.016703] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.016927] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
[ 1.016933] ehci_hcd 0000:00:1d.7: PCI INT D -> Link[LNKH] -> GSI 10 (level, low) -> IRQ 10
[ 1.016951] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.016956] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.017005] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 1.017040] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.020915] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 1.021068] ehci_hcd 0000:00:1d.7: irq 10, io mem 0xe0100000
[ 1.068685] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.068845] hub 1-0:1.0: USB hub found
[ 1.068853] hub 1-0:1.0: 6 ports detected
[ 1.068951] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.068970] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.069195] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 1.069199] PCI: setting IRQ 11 as level-triggered
[ 1.069205] uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 1.069212] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.069216] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.069269] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 1.069293] uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001820
[ 1.069451] hub 2-0:1.0: USB hub found
[ 1.069457] hub 2-0:1.0: 2 ports detected
[ 1.069730] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
[ 1.069733] PCI: setting IRQ 5 as level-triggered
[ 1.069739] uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 5 (level, low) -> IRQ 5
[ 1.069746] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.069751] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.069794] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 1.069819] uhci_hcd 0000:00:1d.1: irq 5, io base 0x00001840
[ 1.069966] hub 3-0:1.0: USB hub found
[ 1.069972] hub 3-0:1.0: 2 ports detected
[ 1.070041] uhci_hcd 0000:00:1d.2: PCI INT C -> Link[LNKC] -> GSI 10 (level, low) -> IRQ 10
[ 1.070048] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.070052] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.070098] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 1.070119] uhci_hcd 0000:00:1d.2: irq 10, io base 0x00001860
[ 1.070280] hub 4-0:1.0: USB hub found
[ 1.070286] hub 4-0:1.0: 2 ports detected
[ 1.070425] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOU2] at 0x60,0x64 irq 1,12
[ 1.119426] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.119435] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.119569] mice: PS/2 mouse device common for all mice
[ 1.119766] rtc_cmos 00:01: RTC can wake from S4
[ 1.119816] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[ 1.119835] rtc0: alarms up to one month, y3k, 242 bytes nvram
[ 1.119989] device-mapper: uevent: version 1.0.3
[ 1.120148] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[ 1.120214] device-mapper: multipath: version 1.1.1 loaded
[ 1.120218] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.120374] EISA: Probing bus 0 at eisa.0
[ 1.120382] Cannot allocate resource for EISA slot 1
[ 1.120386] Cannot allocate resource for EISA slot 2
[ 1.120389] Cannot allocate resource for EISA slot 3
[ 1.120412] EISA: Detected 0 cards.
[ 1.120516] cpuidle: using governor ladder
[ 1.120593] cpuidle: using governor menu
[ 1.120968] TCP cubic registered
[ 1.121163] NET: Registered protocol family 10
[ 1.121627] lo: Disabled Privacy Extensions
[ 1.121911] NET: Registered protocol family 17
[ 1.122217] Using IPI No-Shortcut mode
[ 1.122320] PM: Resume from disk failed.
[ 1.122336] registered taskstats version 1
[ 1.122572] Magic number: 3:684:982
[ 1.122670] rtc_cmos 00:01: setting system clock to 2011-03-16 10:58:56 UTC (1300273136)
[ 1.122676] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.122678] EDD information not available.
[ 1.209798] isapnp: No Plug & Play device found
[ 1.216373] ata2.01: NODEV after polling detection
[ 1.216483] ata1.00: ATA-6: FUJITSU MHV2040AH, 00000096, max UDMA/100
[ 1.216488] ata1.00: 78140160 sectors, multi 16: LBA
[ 1.222509] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 1.226990] ata2.00: ATAPI: QSI DVD+/-RW SDW-082, LX34, max UDMA/33
[ 1.232458] ata1.00: configured for UDMA/100
[ 1.232621] scsi 0:0:0:0: Direct-Access ATA FUJITSU MHV2040A 0000 PQ: 0 ANSI: 5
[ 1.232804] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.232919] sd 0:0:0:0: [sda] 78140160 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 1.232994] sd 0:0:0:0: [sda] Write Protect is off
[ 1.232999] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.233031] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.233245] sda:
[ 1.240458] ata2.00: configured for UDMA/33
[ 1.244345] scsi 1:0:0:0: CD-ROM QSI DVD+-RW SDW-082 LX34 PQ: 0 ANSI: 5
[ 1.250095] sr0: scsi3-mmc drive: 12x/24x writer cd/rw xa/form2 cdda tray
[ 1.250100] Uniform CD-ROM driver Revision: 3.20
[ 1.250211] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.250268] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.267014] sda1 sda2 sda3 < sda5 >
[ 1.298046] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.298067] Freeing unused kernel memory: 688k freed
[ 1.298558] Write protecting the kernel text: 4936k
[ 1.298608] Write protecting the kernel read-only data: 1980k
[ 1.318297] udev[68]: starting version 163
[ 1.602055] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 1.602086] 8139cp 0000:02:02.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 1.607138] firewire_ohci 0000:02:06.2: PCI INT A -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
[ 1.607232] 8139too: 8139too Fast Ethernet driver 0.9.28
[ 1.660067] firewire_ohci: Added fw-ohci device 0000:02:06.2, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2
[ 1.660574] 8139too 0000:02:02.0: PCI INT A -> Link[LNKD] -> GSI 5 (level, low) -> IRQ 5
[ 1.661600] 8139too 0000:02:02.0: eth0: RealTek RTL8139 at 0x3000, 00:c0:9f:48:23:5d, IRQ 5
[ 1.901766] PM: Starting manual resume from disk
[ 1.901772] PM: Resume from partition 8:2
[ 1.901774] PM: Checking hibernation image.
[ 1.916514] PM: Signature found, resuming
[ 1.921281] PM: Marking nosave pages: 000000000009f000 - 0000000000100000
[ 1.921287] PM: Basic memory bitmaps created
[ 1.921289] PM: Preparing processes for restore.
[ 1.921292] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 1.936045] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 1.952054] PM: Reading hibernation image.
[ 1.964801] PM: Loading image data pages (76466 pages) ... 0%
[ 2.160183] firewire_core: created device fw0: GUID 00c09f00001e9415, S400
[ 2.1898 2%
[ 2.276254] ACPI: Battery Slot [BAT1] (battery present)
[ 2.3997 35%
[ 10.144148] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 10.144154] ata1.00: BMDMA stat 0x25
[ 10.144160] ata1.00: failed command: READ DMA
[ 10.144170] ata1.00: cmd c8/00:08:d8:58:57/00:00:00:00:00/e2 tag 0 dma 4096 in
[ 10.144172] res 51/40:04:dc:58:57/00:00:00:00:00/e2 Emask 0x9 (media error)
[ 10.144177] ata1.00: status: { DRDY ERR }
[ 10.144180] ata1.00: error: { UNC }
[ 10.208791] ata1.00: configured for UDMA/100
[ 10.208805] ata1: EH complete
[ 14.444947] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 14.444950] ata1.00: BMDMA stat 0x25
[ 14.444954] ata1.00: failed command: READ DMA
[ 14.444963] ata1.00: cmd c8/00:08:d8:58:57/00:00:00:00:00/e2 tag 0 dma 4096 in
[ 14.444965] res 51/40:04:dc:58:57/00:00:00:00:00/e2 Emask 0x9 (media error)
[ 14.444969] ata1.00: status: { DRDY ERR }
[ 14.444972] ata1.00: error: { UNC }
[ 14.508791] ata1.00: configured for UDMA/100
[ 14.508798] ata1: EH complete
[ 18.823546] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 18.823550] ata1.00: BMDMA stat 0x25
[ 18.823553] ata1.00: failed command: READ DMA
[ 18.823562] ata1.00: cmd c8/00:08:d8:58:57/00:00:00:00:00/e2 tag 0 dma 4096 in
[ 18.823564] res 51/40:04:dc:58:57/00:00:00:00:00/e2 Emask 0x9 (media error)
[ 18.823568] ata1.00: status: { DRDY ERR }
[ 18.823571] ata1.00: error: { UNC }
[ 18.884790] ata1.00: configured for UDMA/100
[ 18.884796] ata1: EH complete
[ 23.124344] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 23.124347] ata1.00: BMDMA stat 0x25
[ 23.124351] ata1.00: failed command: READ DMA
[ 23.124360] ata1.00: cmd c8/00:08:d8:58:57/00:00:00:00:00/e2 tag 0 dma 4096 in
[ 23.124362] res 51/40:04:dc:58:57/00:00:00:00:00/e2 Emask 0x9 (media error)
[ 23.124366] ata1.00: status: { DRDY ERR }
[ 23.124369] ata1.00: error: { UNC }
[ 23.184791] ata1.00: configured for UDMA/100
[ 23.184797] ata1: EH complete
[ 27.425134] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 27.425137] ata1.00: BMDMA stat 0x25
[ 27.425141] ata1.00: failed command: READ DMA
[ 27.425150] ata1.00: cmd c8/00:08:d8:58:57/00:00:00:00:00/e2 tag 0 dma 4096 in
[ 27.425152] res 51/40:04:dc:58:57/00:00:00:00:00/e2 Emask 0x9 (media error)
[ 27.425156] ata1.00: status: { DRDY ERR }
[ 27.425159] ata1.00: error: { UNC }
[ 27.484791] ata1.00: configured for UDMA/100
[ 27.484798] ata1: EH complete
[ 31.725915] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 31.725919] ata1.00: BMDMA stat 0x25
[ 31.725923] ata1.00: failed command: READ DMA
[ 31.725931] ata1.00: cmd c8/00:08:d8:58:57/00:00:00:00:00/e2 tag 0 dma 4096 in
[ 31.725933] res 51/40:04:dc:58:57/00:00:00:00:00/e2 Emask 0x9 (media error)
[ 31.725937] ata1.00: status: { DRDY ERR }
[ 31.725940] ata1.00: error: { UNC }
[ 31.780793] ata1.00: configured for UDMA/100
[ 31.780806] sd 0:0:0:0: [sda] Unhandled sense code
[ 31.780810] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 31.780815] sd 0:0:0:0: [sda] Sense Key : Medium Error [current] [descriptor]
[ 31.780822] Descriptor sense data with sense descriptors (in hex):
[ 31.780825] 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 31.780838] 02 57 58 dc
[ 31.780844] sd 0:0:0:0: [sda] Add. Sense: Unrecovered read error - auto reallocate failed
[ 31.780852] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 02 57 58 d8 00 00 08 00
[ 31.780864] end_request: I/O error, dev sda, sector 39278812
[ 31.780868] Read-error on swap-device (8:0:39278816)
[ 31.780923] ata1: EH complete
[ 31.781218]
[ 31.781223] PM: Read 305864 kbytes in 29.81 seconds (10.26 MB/s)
[ 31.781227] PM: Error -5 resuming
[ 31.781233] PM: Restore failed, recovering.
[ 31.815500] Restarting tasks ... done.
[ 31.817525] PM: Basic memory bitmaps freed
[ 31.822752] PM: Resume from disk failed.
[ 31.879860] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[ 31.879868] EXT4-fs (sda1): write access will be enabled during recovery
[ 32.729123] EXT4-fs (sda1): recovery complete
[ 32.729785] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 48.191441] udev[315]: starting version 163
[ 48.222083] Adding 976892k swap on /dev/sda2. Priority:-1 extents:1 across:976892k
[ 48.409007] lp: driver loaded but no devices found
[ 48.593999] [Firmware Bug]: ACPI: ACPI brightness control misses _BQC function
[ 48.594262] acpi device:03: registered as cooling_device3
[ 48.594414] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input4
[ 48.594496] ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no)
[ 48.629170] intel_rng: FWH not detected
[ 48.715550] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 48.827610] lib80211: common routines for IEEE802.11 drivers
[ 48.827614] lib80211_crypt: registered algorithm 'NULL'
[ 48.860707] Linux agpgart interface v0.103
[ 48.959466] agpgart-intel 0000:00:00.0: Intel 855GM Chipset
[ 48.960147] agpgart-intel 0000:00:00.0: detected 32636K stolen memory
[ 48.962453] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xe8000000
[ 48.966805] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 49.013564] yenta_cardbus 0000:02:06.0: CardBus bridge found [152d:0728]
[ 49.013580] yenta_cardbus 0000:02:06.0: Enabling burst memory read transactions
[ 49.013586] yenta_cardbus 0000:02:06.0: Using CSCINT to route CSC interrupts to PCI
[ 49.013589] yenta_cardbus 0000:02:06.0: Routing CardBus interrupts to PCI
[ 49.013594] yenta_cardbus 0000:02:06.0: TI: mfunc 0x01a21b22, devctl 0x64
[ 49.060499] cfg80211: Calling CRDA to update world regulatory domain
[ 49.149257] [drm] Initialized drm 1.1.0 20060810
[ 49.154565] cfg80211: World regulatory domain updated:
[ 49.154569] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 49.154574] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 49.154578] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 49.154582] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 49.154586] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 49.154590] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 49.161875] libipw: 802.11 data/management/control stack, git-1.1.13
[ 49.161878] libipw: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 49.178418] type=1400 audit(1300273184.552:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient3" pid=575 comm="apparmor_parser"
[ 49.179272] type=1400 audit(1300273184.552:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=575 comm="apparmor_parser"
[ 49.179740] type=1400 audit(1300273184.552:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=575 comm="apparmor_parser"
[ 49.232610] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[ 49.232616] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 49.260469] yenta_cardbus 0000:02:06.0: ISA IRQ mask 0x00d8, PCI irq 10
[ 49.260474] yenta_cardbus 0000:02:06.0: Socket status: 30000006
[ 49.260480] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #02 to #06
[ 49.260498] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [io 0x3000-0x3fff]
[ 49.260503] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3000-0x3fff: excluding 0x3000-0x30ff 0x3400-0x34ff 0x3800-0x38ff
[ 49.271162] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [mem 0xe0200000-0xe05fffff]
[ 49.271169] pcmcia_socket pcmcia_socket0: cs: memory probe 0xe0200000-0xe05fffff: excluding 0xe0200000-0xe023ffff
[ 49.271189] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [mem 0x50000000-0x53ffffff pref]
[ 49.271193] pcmcia_socket pcmcia_socket0: cs: memory probe 0x50000000-0x53ffffff: excluding 0x50000000-0x53ffffff
[ 49.297412] tifm_7xx1 0000:02:06.3: PCI INT A -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
[ 49.298394] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
[ 49.298400] ipw2200 0000:02:04.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
[ 49.312192] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 49.369560] i915 0000:00:02.0: power state changed by ACPI to D0
[ 49.369573] i915 0000:00:02.0: power state changed by ACPI to D0
[ 49.369584] i915 0000:00:02.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 49.369590] i915 0000:00:02.0: setting latency timer to 64
[ 49.396611] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[ 49.411342] [drm] set up 31M of stolen space
[ 49.522458] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: excluding 0x170-0x177 0x1c0-0x1cf 0x1f0-0x1f7 0x370-0x377
[ 49.524289] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x4d0-0x4d7
[ 49.525009] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 49.540693] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 49.541353] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xc7fff 0xcc000-0xcffff 0xe0000-0xfffff
[ 49.541430] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: clean.
[ 49.541505] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: clean.
[ 49.541584] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 49.574171] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 49.574705] [drm] initialized overlay support
[ 49.902913] ipw2200: Radio Frequency Kill Switch is On:
[ 49.902916] Kill switch must be turned off for wireless networking to work.
[ 49.980205] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
[ 50.060239] Skipping EDID probe due to cached edid
[ 50.109931] Synaptics Touchpad, model: 1, fw: 5.10, id: 0x258eb1, caps: 0xa04713/0x0/0x0
[ 50.143602] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input5
[ 50.384192] Console: switching to colour frame buffer device 160x48
[ 50.390314] fb0: inteldrmfb frame buffer device
[ 50.390317] drm: registered panic notifier
[ 50.390637] Slow work thread pool: Starting up
[ 50.395823] Slow work thread pool: Ready
[ 50.395842] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 50.396124] Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
[ 50.396160] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 50.624270] Skipping EDID probe due to cached edid
[ 50.732075] intel8x0_measure_ac97_clock: measured 54072 usecs (2605 samples)
[ 50.732082] intel8x0: clocking to 48000
[ 51.894182] eth0: link down
[ 51.894464] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 51.955053] type=1400 audit(1300273187.328:5): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=837 comm="apparmor_parser"
[ 51.963658] type=1400 audit(1300273187.336:6): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=839 comm="apparmor_parser"
[ 51.969964] type=1400 audit(1300273187.344:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=839 comm="apparmor_parser"
[ 51.970437] type=1400 audit(1300273187.344:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=839 comm="apparmor_parser"
[ 51.992507] type=1400 audit(1300273187.368:9): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=841 comm="apparmor_parser"
[ 52.019134] type=1400 audit(1300273187.392:10): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=841 comm="apparmor_parser"
[ 52.028354] type=1400 audit(1300273187.404:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=841 comm="apparmor_parser"
[ 53.273907] ppdev: user-space parallel port driver
[ 56.927993] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[ 57.039827] EXT4-fs (sda5): re-mounted. Opts: commit=0
[ 58.136049] ipw2200: Failed to send POWER_MODE: Command timed out.
[ 77.382459] atkbd serio0: Unknown key pressed (translated set 2, code 0xd5 on isa0060/serio0).
[ 77.382465] atkbd serio0: Use 'setkeycodes e055 <keycode>' to make it known.
[ 77.392568] atkbd serio0: Unknown key released (translated set 2, code 0xd5 on isa0060/serio0).
[ 77.392573] atkbd serio0: Use 'setkeycodes e055 <keycode>' to make it known.
[ 78.297009] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 78.815315] lib80211_crypt: registered algorithm 'WEP'
[ 79.238094] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 129.446162] lo: Disabled Privacy Extensions
[ 168.179588] lo: Disabled Privacy Extensions

/var/log/messages è super lungo, devo postarti qualcosa in particolare? (anche se metto in spoiler occupata tutta la pagina O_o)

[sacarde]

non ho visto errori, solo:

cat dmesg.txt|grep eth1

[ 58.136049] ipw2200: Failed to send POWER_MODE: Command timed out.
...
[ 78.297009] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 79.238094] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready


prova a fare altrettanto a messages

cat /var/log/messages | grep eth1
o
cat /var/log/messages | grep ipw22

[ambulanza]

Mar 14 11:48:01 ambulanza-00000000000000000000000 kernel: [ 4833.117198] ADDRCONF(NETDEV_UP): eth1: link is not ready
Mar 14 11:48:20 ambulanza-00000000000000000000000 kernel: [ 4851.942381] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Mar 15 01:20:30 ambulanza-00000000000000000000000 kernel: [ 124.750045] ADDRCONF(NETDEV_UP): eth1: link is not ready
Mar 15 01:20:31 ambulanza-00000000000000000000000 kernel: [ 126.062414] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Mar 15 11:52:42 ambulanza-00000000000000000000000 kernel: [ 45.028551] ADDRCONF(NETDEV_UP): eth1: link is not ready
Mar 15 11:52:51 ambulanza-00000000000000000000000 kernel: [ 53.735967] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Mar 15 23:29:12 ambulanza-00000000000000000000000 kernel: [ 76.827139] ADDRCONF(NETDEV_UP): eth1: link is not ready
Mar 15 23:29:13 ambulanza-00000000000000000000000 kernel: [ 78.570471] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Mar 16 12:00:13 ambulanza-00000000000000000000000 kernel: [ 78.297009] ADDRCONF(NETDEV_UP): eth1: link is not ready
Mar 16 12:00:14 ambulanza-00000000000000000000000 kernel: [ 79.238094] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready



Mar 14 16:33:42 ambulanza-00000000000000000000000 kernel: [21974.398976] ipw2200: Firmware error detected. Restarting.
Mar 14 18:01:39 ambulanza-00000000000000000000000 kernel: [ 18.141226] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
Mar 14 18:01:39 ambulanza-00000000000000000000000 kernel: [ 18.141231] ipw2200: Copyright(c) 2003-2006 Intel Corporation
Mar 14 18:01:39 ambulanza-00000000000000000000000 kernel: [ 18.154256] ipw2200 0000:02:04.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
Mar 14 18:01:39 ambulanza-00000000000000000000000 kernel: [ 18.180135] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
Mar 14 18:01:39 ambulanza-00000000000000000000000 kernel: [ 18.473262] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
Mar 15 01:18:47 ambulanza-00000000000000000000000 kernel: [ 18.511107] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
Mar 15 01:18:47 ambulanza-00000000000000000000000 kernel: [ 18.511112] ipw2200: Copyright(c) 2003-2006 Intel Corporation
Mar 15 01:18:47 ambulanza-00000000000000000000000 kernel: [ 18.586850] ipw2200 0000:02:04.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
Mar 15 01:18:47 ambulanza-00000000000000000000000 kernel: [ 18.600083] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
Mar 15 01:18:47 ambulanza-00000000000000000000000 kernel: [ 18.836429] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
Mar 15 11:52:19 ambulanza-00000000000000000000000 kernel: [ 18.384243] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
Mar 15 11:52:19 ambulanza-00000000000000000000000 kernel: [ 18.384247] ipw2200: Copyright(c) 2003-2006 Intel Corporation
Mar 15 11:52:19 ambulanza-00000000000000000000000 kernel: [ 18.427134] ipw2200 0000:02:04.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
Mar 15 11:52:19 ambulanza-00000000000000000000000 kernel: [ 18.452076] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
Mar 15 11:52:19 ambulanza-00000000000000000000000 kernel: [ 18.742480] ipw2200: Radio Frequency Kill Switch is On:
Mar 15 11:52:19 ambulanza-00000000000000000000000 kernel: [ 18.743910] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
Mar 15 23:28:22 ambulanza-00000000000000000000000 kernel: [ 22.653163] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
Mar 15 23:28:22 ambulanza-00000000000000000000000 kernel: [ 22.653170] ipw2200: Copyright(c) 2003-2006 Intel Corporation
Mar 15 23:28:22 ambulanza-00000000000000000000000 kernel: [ 23.306871] ipw2200 0000:02:04.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
Mar 15 23:28:22 ambulanza-00000000000000000000000 kernel: [ 23.324105] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
Mar 15 23:28:22 ambulanza-00000000000000000000000 kernel: [ 23.525638] ipw2200: Radio Frequency Kill Switch is On:
Mar 15 23:28:22 ambulanza-00000000000000000000000 kernel: [ 23.527097] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
Mar 16 11:26:17 ambulanza-00000000000000000000000 kernel: [ 18.516157] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
Mar 16 11:26:17 ambulanza-00000000000000000000000 kernel: [ 18.516163] ipw2200: Copyright(c) 2003-2006 Intel Corporation
Mar 16 11:26:17 ambulanza-00000000000000000000000 kernel: [ 18.601092] ipw2200 0000:02:04.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
Mar 16 11:26:17 ambulanza-00000000000000000000000 kernel: [ 18.612137] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
Mar 16 11:26:17 ambulanza-00000000000000000000000 kernel: [ 18.933103] ipw2200: Radio Frequency Kill Switch is On:
Mar 16 11:26:17 ambulanza-00000000000000000000000 kernel: [ 19.246391] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
Mar 16 11:59:47 ambulanza-00000000000000000000000 kernel: [ 49.232610] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
Mar 16 11:59:47 ambulanza-00000000000000000000000 kernel: [ 49.232616] ipw2200: Copyright(c) 2003-2006 Intel Corporation
Mar 16 11:59:47 ambulanza-00000000000000000000000 kernel: [ 49.298400] ipw2200 0000:02:04.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
Mar 16 11:59:47 ambulanza-00000000000000000000000 kernel: [ 49.312192] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
Mar 16 11:59:47 ambulanza-00000000000000000000000 kernel: [ 49.902913] ipw2200: Radio Frequency Kill Switch is On:
Mar 16 11:59:47 ambulanza-00000000000000000000000 kernel: [ 49.980205] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
Mar 16 13:14:27 ambulanza-00000000000000000000000 kernel: [ 18.753949] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
Mar 16 13:14:27 ambulanza-00000000000000000000000 kernel: [ 18.753954] ipw2200: Copyright(c) 2003-2006 Intel Corporation
Mar 16 13:14:27 ambulanza-00000000000000000000000 kernel: [ 18.799120] ipw2200 0000:02:04.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
Mar 16 13:14:27 ambulanza-00000000000000000000000 kernel: [ 18.813231] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
Mar 16 13:14:27 ambulanza-00000000000000000000000 kernel: [ 19.078050] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
Mar 16 13:18:46 ambulanza-00000000000000000000000 kernel: [ 18.395453] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
Mar 16 13:18:46 ambulanza-00000000000000000000000 kernel: [ 18.395459] ipw2200: Copyright(c) 2003-2006 Intel Corporation
Mar 16 13:18:46 ambulanza-00000000000000000000000 kernel: [ 18.473254] ipw2200 0000:02:04.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
Mar 16 13:18:46 ambulanza-00000000000000000000000 kernel: [ 18.490756] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
Mar 16 13:18:46 ambulanza-00000000000000000000000 kernel: [ 19.131106] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
Mar 16 13:20:16 ambulanza-00000000000000000000000 kernel: [ 18.372592] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
Mar 16 13:20:16 ambulanza-00000000000000000000000 kernel: [ 18.372598] ipw2200: Copyright(c) 2003-2006 Intel Corporation
Mar 16 13:20:16 ambulanza-00000000000000000000000 kernel: [ 18.433259] ipw2200 0000:02:04.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
Mar 16 13:20:16 ambulanza-00000000000000000000000 kernel: [ 18.454608] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
Mar 16 13:20:16 ambulanza-00000000000000000000000 kernel: [ 19.115881] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)


non capisco, perchè diventa ready dopo qualche tentativo... cioè bho ora la connessione va bene eh, che comandi sono?

[sacarde]

il problema e' che va dopo 1/2 ora...



il firmware cel'hai?

scaricalo da:
http://ipw2200.sourceforge.net/firmware.php?fid=4


leggi l'ultimo post:
http://forum.ubuntu-it.org/index.php?topic=419418.0

[ambulanza]

Originariamente inviato da sacarde

il problema e' che va dopo 1/2 ora...



il firmware cel'hai?

scaricalo da:
http://ipw2200.sourceforge.net/firmware.php?fid=4


leggi l'ultimo post:
http://forum.ubuntu-it.org/index.php?topic=419418.0

ma credo che il problema non sia alla scheda wireless... cioè le reti me le trova tutte subito, e si connette. mi dice connesso a wifi-studenti (il wifi dell'un) ma poi quando carico la pagine mi dice pagina non disponibile O_o...
ora comunque provo con i driver.

[sacarde]

ma se non ti risponde al ping al default-gateway...

sembra che tu non sia in rete