Consiglio su Router Cisco

[Hack3rAttack]

ecco l'ultimo log ma no nnaviga:

Router>sh int
ATM0 is up, line protocol is up
Hardware is PQUICC_SAR (with Alcatel ADSL Module)
MTU 1500 bytes, sub MTU 1500, BW 320 Kbit, DLY 80 usec,
reliability 0/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5 AAL2, PVC mode
10 maximum active VCs, 1024 VCs per VP, 0 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Per VC Queueing
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 4 interface resets
0 output buffer failures, 0 output buffers swapped out
Dialer0 is up (spoofing), line protocol is up (spoofing)
Hardware is Unknown
MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
DTR is pulsed for 1 seconds on reset
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 42 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
0 packets output, 0 bytes
Ethernet0 is up, line protocol is up
Hardware is PQUICC Ethernet, address is 0011.5cb7.a174 (bia 0011.5cb7.a174)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 10Mb/s
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:30, output 00:00:04, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/100 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
62 packets input, 7929 bytes, 0 no buffer
Received 62 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
72 packets output, 7770 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Router>

[cisketto]

Encapsulation HDLC???
che caspiterina ci fa sotto il dialer?
deve essere ppp!

encapsulation ppp

[cisketto]

fammi capire un po tu prima hai postato uno "sh start"? se si allora vedi di postarmi uno "sh runn"!

[Hack3rAttack]

cisketto, ho cambiato l'encapsulation a ppp sotto dialer 0 ma cmq non naviga, tutte le interfacce soon UP.

Ho notato che spegnendo il router non mantiene salvato, e devo riabilitare tutte le interfacce mannaggi a alui.

Ora ti posto un sh runn
Prima ti ho postato un sh int

[Hack3rAttack]

Ecccoti l'sh runn

Router#sh runn
Building configuration...

Current configuration : 591 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
memory-size iomem 15
logging queue-limit 100
!
ip subnet-zero
!
!
!
!
!
!
!
!
!
interface Ethernet0
no ip address
hold-queue 100 out
!
interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
!
interface Dialer0
no ip address
encapsulation ppp
!
ip classless
no ip http server
no ip http secure-server
!
!
line con 0
no modem enable
stopbits 1
line aux 0
line vty 0 4
!
scheduler max-task-time 5000
!
end

Router#

[Hack3rAttack]

Ti ho postato l'sh runn cisketto nel thread sopra, magari continuiamo li da or ain poi

[CH1CC0]

vedendo lo show run, mi sa che hai il config register "puntato male"...

fai uno show ver e postalo
inoltre controlla che il config register sia puntato su 0x2102 (se fosse su 0x2142 allora cambialo in questo modo:
conf t
config-register 0x2102
riavvia il router e tutto dovrebbe andare a posto)

[Hack3rAttack]

Mi dici come si riavvia il router?
Il comando

[cisketto]

reload