secondary master nn trovato

[khri81]

nessuna distro mi vede il secondary master, mi vedono il primary master, slave il secondary slave, ma il master no! solo windows e le distro linux live cd!

guardando bene mi da un messaggio di errore durante il boot di debian che dice che ide 1 master è in collisione con un altra periferica, ma nn so quale nn lo dice!!!

ho una scheda abit ic7max3! cioè aiutatemi nn so più che fare, mi tocca rinunciare a linux x na cazzata del genere!!!

[VICIUS]

Sicuro di non aver impostato due drive come master o come slave sullo stesso cavo ide ? Controlla bene i jumper.

ciao

[khri81]

sicurissimo! scusa ma allora xchè le distro live mi vedono tutti e 4 i device sui canali ide?
il problema risiede da un altra parte!

e poi scusa win nn mi da questi problemi!

[NA01]

posta il log di avvio completo

quindi alla fine non era un problema di gentoo

[khri81]

dove lo trovo il log di avvio completo?

[NA01]

buttaci il dmesg

cia

[khri81]

Linux version 2.4.18-bf2.4 (root@zombie) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 Son Apr 14 09:53:28 CEST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
found SMP MP-table at 000f5d50
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f0000 reserved twice.
hm, page 000f1000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Unknown CPU [15:2] APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 1
Kernel command line: BOOT_IMAGE=Linux ro root=305
Initializing CPU#0
Detected 3015.243 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 6016.20 BogoMIPS
Memory: 512680k/524224k available (1783k kernel code, 11156k reserved, 549k data, 280k init, 0k highmem)
Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: bfebfbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 12K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After vendor init, caps: bfebfbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-3, 2-4, 2-5, 2-7, 2-10, 2-11, 2-20, 2-22 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 22.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00178020
....... : arbitration: 00
WARNING: unexpected IO-APIC, please mail
to linux-smp@vger.kernel.org
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 1 0 0 0 0 0 0 00
06 001 01 0 0 0 0 0 1 1 41
07 000 00 1 0 0 0 0 0 0 00
08 001 01 0 0 0 0 0 1 1 49
09 001 01 0 0 0 0 0 1 1 51
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 001 01 0 0 0 0 0 1 1 59
0d 001 01 0 0 0 0 0 1 1 61
0e 001 01 0 0 0 0 0 1 1 69
0f 001 01 0 0 0 0 0 1 1 71
10 001 01 1 1 0 1 0 1 1 79
11 001 01 1 1 0 1 0 1 1 81
12 001 01 1 1 0 1 0 1 1 89
13 001 01 1 1 0 1 0 1 1 91
14 000 00 1 0 0 0 0 0 0 00
15 001 01 1 1 0 1 0 1 1 99
16 000 00 1 0 0 0 0 0 0 00
17 001 01 1 1 0 1 0 1 1 A1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ6 -> 0:6
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ21 -> 0:21
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 3015.2938 MHz.
..... host bus clock speed is 215.3779 MHz.
cpu: 0, clocks: 2153779, slice: 1076889
CPU0<T0:2153776,T1:1076880,D:7,S:1076889,C:2153779>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfba20, last bus=3
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
Unknown bridge resource 2: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router default [8086/24d0] at 00:1f.0
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P1) -> 19
PCI->APIC IRQ transform: (B0,I29,P2) -> 18
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P3) -> 23
PCI->APIC IRQ transform: (B0,I31,P0) -> 18
PCI->APIC IRQ transform: (B0,I31,P0) -> 18
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI->APIC IRQ transform: (B2,I1,P0) -> 18
PCI->APIC IRQ transform: (B3,I2,P0) -> 18
PCI->APIC IRQ transform: (B3,I5,P0) -> 21
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
Journalled Block Device driver loaded
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
Console: switching to colour frame buffer device 80x30
fb0: VGA16 VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
Real Time Clock Driver v1.10e
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PCI_IDE: unknown IDE controller on PCI bus 00 device f9, VID=8086, DID=24db
PCI: Device 00:1f.1 not available because of resource collisions
PCI_IDE: chipset revision 2
PCI_IDE: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hdaio, hdbio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdcio, hddio
PCI_IDE: unknown IDE controller on PCI bus 00 device fa, VID=8086, DID=24d1
PCI_IDE: chipset revision 2
PCI_IDE: 100% native mode on irq 18
ide2: BM-DMA at 0xd000-0xd007, BIOS settings: hdeio, hdfio
ide3: BM-DMA at 0xd008-0xd00f, BIOS settings: hdgio, hdhio
hda: QUANTUM FIREBALLP LM20.5, ATA DISK drive
hdb: Maxtor 91741U4, ATA DISK drive
hdd: RW-481248 1.07, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 40132503 sectors (20548 MB) w/1900KiB Cache, CHS=2498/255/63
hdb: 34004880 sectors (17410 MB) w/512KiB Cache, CHS=2116/255/63
hdd: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.12
ide-floppy driver 0.97.sv
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 >
hdb: hdb1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Loading I2O Core - (c) Copyright 1999 Red Hat Software
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
loop: loaded (max 8 devices)
Compaq CISS Driver (v 2.4.5)
HDLC support module revision 1.02 for Linux 2.4
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
ide-floppy driver 0.97.sv
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.01
No raid array found
SCSI subsystem driver Revision: 1.00
Red Hat/Adaptec aacraid driver, Apr 14 2002
DC390: 0 adapters found
3ware Storage Controller device driver for Linux v1.02.00.016.
3w-xxxx: No cards with valid units found.
request_module[scsi_hostadapter]: Root fs not mounted
request_module[scsi_hostadapter]: Root fs not mounted
i2o_scsi.c: Version 0.0.1
chain_pool: 0 bytes @ c1852360
(512 byte buffers X 4 can_queue X 0 i2o controllers)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
cramfs: wrong magic
FAT: bogus logical sector size 0
reiserfs: checking transaction log (device 03:05) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 280k freed
Adding Swap: 489940k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 10:29:43 Apr 14 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xbc00, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xb000, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 18
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.3 to 64
usb-uhci.c: USB UHCI at I/O 0xb800, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver keyboard
usbkbd.c: :USB HID Boot Protocol keyboard driver



dmesg di debian.

[NA01]

qui nulla

puoi postare il messaggio che dicevi in avvio?

cia

[khri81]

hda: 40132503 sectors (20548 MB) w/1900KiB Cache, CHS=2498/255/63
hdb: 34004880 sectors (17410 MB) w/512KiB Cache, CHS=2116/255/63
hdd: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache


vedi che nn legge l'hdc!!!! ti assicuro che le distro live e win lo vedono e funziona senza problemi!

quale può essere il prob?

[NA01]

si, visto

quale è precisamente l'errore che dicevi nel primo post?

cia

[khri81]

mi da un errore di collisione degli irq, ma nn so cazzo voglia dire sinceramente!!!

cioè debian, gentoo e qualsiasi altro distro installata su hd nn vede l'hdc!

win e le distro live si!

[NA01]

non è che è seguita o preceduta da qualcosa sull'acpi?
dovresti trovarlo dentro
/var/log/messages
prova a cercarlo e a postarelo inseime a qualche riga prima e dopo


cia

[AnonimoVeneziano]

Stai usando il Kernel 2.4.18 della debian , probabilmente è un po' troppo antico .

Dovresti usare un disco di installazione + nuovo per installare un kernel + recente (se vuoi ti mando un disco mini di Sarge RC1 da 8MB ) .

Oppure (soluzione + semplice ) metti un kernel + recente .

Ti consiglio di Upgradare prima a Sarge o SID , a sto punto metti un kernel + recente che supporta il tuo sistema relativamente nuovo

Ciao

[maxithron]

Per i messaggi di avvio, in genere, sarebbe meglio attivare anche il servizio bootlogd.

[khri81]

no aspe raga, io su gentoo, ho cacciato su il kernel 2.6.7 ho pure provato il .8.1 ma dava problemi alla scheda audio, ma cmq il secondary master nn viene visto!

e poi cmq anche le distro live che ho provato hanno un kernel 2.4 vecchio eppure loro nn mi danno questo problema e funziona tutto bene!


scheda madre difettosa nn credo propio xchè su windows e le distro live tutti e 4 i device sui canali ide funzionano alla perfezione!

[khri81]

Sep 6 20:31:05 flexo kernel: Uniform Multi-Platform E-IDE driver Revision: 6.31
Sep 6 20:31:05 flexo kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Sep 6 20:31:05 flexo kernel: PCI_IDE: unknown IDE controller on PCI bus 00 device f9, VID=8086, DID=24db
Sep 6 20:31:05 flexo kernel: PCI_IDE: chipset revision 2
Sep 6 20:31:05 flexo kernel: PCI_IDE: not 100%% native mode: will probe irqs later
Sep 6 20:31:05 flexo kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hdaio, hdbio
Sep 6 20:31:05 flexo kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdcio, hddio
Sep 6 20:31:05 flexo kernel: PCI_IDE: unknown IDE controller on PCI bus 00 device fa, VID=8086, DID=24d1
Sep 6 20:31:05 flexo kernel: PCI_IDE: chipset revision 2
Sep 6 20:31:05 flexo kernel: PCI_IDE: 100%% native mode on irq 18
Sep 6 20:31:05 flexo kernel: ide2: BM-DMA at 0xd000-0xd007, BIOS settings: hdeio, hdfio
Sep 6 20:31:05 flexo kernel: ide3: BM-DMA at 0xd008-0xd00f, BIOS settings: hdgio, hdhio
Sep 6 20:31:05 flexo kernel: hda: QUANTUM FIREBALLP LM20.5, ATA DISK drive
Sep 6 20:31:05 flexo kernel: hdb: Maxtor 91741U4, ATA DISK drive
Sep 6 20:31:05 flexo kernel: hdd: RW-481248 1.07, ATAPI CD/DVD-ROM drive
Sep 6 20:31:05 flexo kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Sep 6 20:31:05 flexo kernel: ide1 at 0x170-0x177,0x376 on irq 15
Sep 6 20:31:05 flexo kernel: hda: 40132503 sectors (20548 MB) w/1900KiB Cache, CHS=2498/255/63
Sep 6 20:31:05 flexo kernel: hdb: 34004880 sectors (17410 MB) w/512KiB Cache, CHS=2116/255/63
Sep 6 20:31:05 flexo kernel: hdd: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache
Sep 6 20:31:05 flexo kernel: Uniform CD-ROM driver Revision: 3.12



tanto x cominciare quanti cavolo di controller ide mi trova?

ho addirittura hdf!!!!!

e poi xchè il primo controllor mi dice not 100% compatible, mentre il secondo 100% compatible?

[NA01]

ma l'errore?

[khri81]

nn lo trovo da nessuna parte. cmq c'è del casino con i controller ide e l'sata che da quanto ho visto nn vengono riconosciuti correttamente! solo che nn so come fare visto che nemmeno i kernel 2.6 li riconoscono correttamente!

cmq nn uso sata solo i canali ide 2 hd, mast e dvd, il controller sata lo disattivo ma si vede che da rogne lo stesso!

ho questi controller sulla cheda madre:

canale primario ide
canale primario ide
canale secondario ide
canale secondario ide
intel 8280 1eb ultra ata storage controllers
intel 8280 1eb ultra ata storage controllers

linux si vede che nn li vede correttamente oppure fa del casino!

[khri81]

help

[NA01]

senza l'errore non so come ti si possa aiutare....

cmq prova a disabilitare l'acpi

cia