mi potete aiutare a configurare lo scanner ? (epson - debian)

[Simone XP]

Ciao, il mio scanner è un epson perfection 1650 photo:
ho installato xsane con apt-get, poi ho compilato il supporto usb direttamente nel kernel (non come modulo)
ed ho messo nel fstab:
none /proc/bus/usb usbdevfs defaults 0 0
ho editato il file /etc/sane.d/epson.conf in modo che rimanesse solo la riga

usb /dev/usbscanner0


poi ho creato il dev usbscanner : mknod /dev/usbscanner0 c 180 48


ed ho cambiato i permessi: chmod 660 /dev/usbscanner0


ma quando provo ad avviare xsane come risultato ho sempre:
"no SANE device found".

Inoltre se provo a dare cat /proc/bus/usb/devices ottengo niente!

Cosa devo fare? lo scanner non ho mai provato a configurarlo sotto debian prima di adesso, ma facendo quello che ho scritto sopra con altre distribuzioni ha sempre funzionato!

Grazie

[Simone XP]

up

[VICIUS]

domanda stupida. il modulo scanner.o è caricato ?

per poter fare cat /proc/bus/usb/devices serve un kernel con l'opzione "preliminary usb filesystem" è selezionata ?. Inoltre il filesystem va montato. basta aggiungere questa linea in fstab:

none            /proc/bus/usb   usbfs   defaults                0       0

ciao

[Simone XP]

Originariamente inviato da VICIUS
domanda stupida. il modulo scanner.o è caricato ?

per poter fare cat /proc/bus/usb/devices serve un kernel con l'opzione "preliminary usb filesystem" è selezionata ?. Inoltre il filesystem va montato. basta aggiungere questa linea in fstab:

none            /proc/bus/usb   usbfs   defaults                0       0

ciao

come carico il modulo scanner.o? l'opzione nel kernel è compilata, ho aggiunto quel codice il fstab l'avevo messo ma con file system usbdevfs, lo cambio con usbfs?
ciao

[VICIUS]

Originariamente inviato da Simone XP
come carico il modulo scanner.o? l'opzione nel kernel è compilata, ho aggiunto quel codice il fstab l'avevo messo ma con file system usbdevfs, lo cambio con usbfs?
ciao

il modulo lo carichi con modprobe scanner oppure con modoconf.

usbdevfs penso sia deprecato. ora gli hanno cambiato nome e in usbfs.

ciao

[Simone XP]

Originariamente inviato da VICIUS
il modulo lo carichi con modprobe scanner oppure con modoconf.

usbdevfs penso sia deprecato. ora gli hanno cambiato nome e in usbfs.

ciao

per il modulo dice can't locate, ma io ho compilato tuto come build-in, ho cambiato usbdevfs con usbfs ma continua a non funzionare...cosa devo fare?

[Simone XP]

è normale che /proc/bus/usb non esista?

[Simone XP]

up

[VICIUS]

Originariamente inviato da Simone XP
è normale che /proc/bus/usb non esista?

di solito non c'è ma montanto il filesystem usbfs compare. sei sicuro di aver caricato tutti i moduli all'avvio ? non è che puoi allegare l'output del comando dmesg ?

ciao

[Simone XP]

hal-9000:~# dmesg
Linux version 2.4.21 (root@hal-9000) (gcc version 3.3.1 20030626 (Debian prerelease)) #7 Tue Jul 22 22:05:37 CEST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff8000 (ACPI data)
BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffee0000 - 00000000fff00000 (reserved)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=linux2421 ro root=307 hdc=ide-scsi hdd=ide-scsi
ide_setup: hdc=ide-scsi
ide_setup: hdd=ide-scsi
Initializing CPU#0
Detected 1460.471 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2916.35 BogoMIPS
Memory: 515112k/524224k available (2049k kernel code, 8724k reserved, 671k data, 120k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383f9ff c1cbf9ff 00000000 00000000
CPU: Common caps: 0383f9ff c1cbf9ff 00000000 00000000
CPU: AMD Athlon(tm) XP 1700+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router SIS [1039/0008] at 00:02.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
udf: registering filesystem
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
i2c-core.o: driver i2c-dev dummy driver registered.
i2c-algo-pcf.o: i2c pcf8584 algorithm module
i2c-elektor.o: i2c pcf8584-isa adapter module
i2c-proc.o version 2.6.1 (20010825)
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
via-rhine.c:v1.10-LK1.1.17 March-1-2003 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
PCI: Found IRQ 11 for device 00:0f.0
PCI: Sharing IRQ 11 with 00:02.2
eth0: VIA VT6105 Rhine-III at 0xd400, 00:03:6d:30:69:ce, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
PCI: Found IRQ 5 for device 00:11.0
eth1: VIA VT6105 Rhine-III at 0xd000, 00:03:6d:30:61:fa, IRQ 5.
eth1: MII PHY found at address 1, status 0x786d advertising 05e1 Link 0021.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected SiS 735 chipset
agpgart: AGP aperture is 128M @ 0xd0000000
[drm] Initialized tdfx 1.0.0 20010216 on minor 0
[drm] AGP 0.99 on SiS @ 0xd0000000 128MB
[drm] Initialized radeon 1.1.1 20010405 on minor 1
[drm] AGP 0.99 on SiS @ 0xd0000000 128MB
[drm] Initialized i810 1.2.0 20010920 on minor 2
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 00:02.5
SIS5513: chipset revision 208
SIS5513: not 100% native mode: will probe irqs later
SiS735 ATA 100 controller
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hdaMA, hdbMA
ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdcMA, hddMA
hda: ST3120023A, ATA DISK drive
blk: queue c03f1980, I/O limit 4095Mb (mask 0xffffffff)
hdc: LITEON DVD-ROM LTD163D, ATAPI CD/DVD-ROM drive
hdd: HL-DT-ST GCE-8480B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=14593/255/63, UDMA(100)
hdc: attached ide-scsi driver.
hdd: attached ide-scsi driver.
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 >
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: LITEON Model: DVD-ROM LTD163D Rev: GHR3
Type: CD-ROM ANSI SCSI revision: 02
Vendor: HL-DT-ST Model: CD-RW GCE-8480B Rev: 1.03
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 0x/48x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Intel 810 + AC97 Audio, version 0.24, 22:13:46 Jul 22 2003
PCI: Found IRQ 11 for device 00:02.7
i810: SiS 7012 found at IO 0xd800 and 0xdc00, MEM 0x0000 and 0x0000, IRQ 11
i810_audio: Audio Controller supports 2 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 Audio codec, id: ALC38 (Unknown)
i810_audio: only 48Khz playback available.
i810_audio: AC'97 codec 0 supports AMAP, total channels = 2
es1371: version v0.32 time 22:14:00 Jul 22 2003
usb.c: registered new driver hub
host/uhci.c: USB Universal Host Controller Interface driver v1.1
usb.c: registered new driver usbscanner
scanner.c: 0.4.12:USB Scanner Driver
usb.c: registered new driver usblp
printer.c: v0.11: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 292 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 120k freed
Adding Swap: 1036152k swap-space (priority -1)
0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-4363 Sat Apr 19 17:46:46 PDT 2003
eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
/dev/vmmon: Module vmmon: registered with major=10 minor=165
/dev/vmmon: Module vmmon: initialized
/dev/vmnet: open called by PID 264 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: up
bridge-eth0: attached
/dev/vmnet: open called by PID 287 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 288 (vmnet-netifup)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 289 (vmnet-natd)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 310 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 311 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
hal-9000:~#

[Simone XP]

comunaque non lo monta (credo)

hal-9000:~# mount -t usbfs none /proc/bus/usb
mount: mount point /proc/bus/usb does not exist
hal-9000:~# mount -t usbdevfs none /proc/bus/usb
mount: mount point /proc/bus/usb does not exist
hal-9000:~#

[VICIUS]

sei _sicuro_ di aver selezionato l'opzione nel kernel ??

[Simone XP]

Originariamente inviato da VICIUS
sei _sicuro_ di aver selezionato l'opzione nel kernel ??

quali ozioni devo selezionare?

[Simone XP]

ok, sono riuscito a farlo funzionare, ora volevo chiederti se conosci un programma che mi permetta di fare le scansioni dei negativi. Lo scanner lo supporta e teoricamente anche xsane, ma in realtà non funziona, esiste un programma tipo il twain di windows che fa le scansioni e le converte in positivo automaticamente?
ciao

[Simone XP]

forse ho fatto una cavolata!

ho seguito queste istruzioni

8. Installing and patching the Epson Image Scan! Software for Linux.

First ensure your scanner works with xsane or xscanimage.

As user:

a. Download iscan-1.4.0-1.i386.rpm, NOT the source tarball.
http://www.epkowa.co.jp/english/linux_e/lsd_e.html

As Root or SU:

b. Convert the RPM to Debian: alien iscan_-1.4.0-1.i386.rpm
c. Install: dpkg -i iscan_1.4.0-2_i386.deb (the resulting deb file from step b)
d. cd /usr/lib/sane
e. rm libsane-epson.so.1 (this is a symbolic link)
f. ln -s libsane-epsonkw.so.1.0.6 libsane-epson.so.1
g. (Optional) echo "libsane hold" | dpkg --set-selections (to prevent overwrite by future
upgrades)
h. (Optional) ln -s /usr/bin/iscan /usr/lib/gimp/1.2/plug-ins/ (to use iscan from within the
gimp)
i. Change group from root to scan for /usr/bin/iscan (chown root.scan /usr/bin/iscan)
j. Change permission: chmod 0777 /usr/bin/iscan

To start Image Scan: iscan


solo dopo mi sono accorto che facendo rm libsane-epson.so.1 rimuovo questo file....io l'ho copiato senza accorgermene e ora non funziona più lo scannner nemmeno con xsane!!! come posso fare?

[Simone XP]

sono riuscito a sistemarlo in questo modo:
ln -s libsane-epson.so.1.0.12 libsane-epson.so.1

ora mi dite come si fa a installare iscan sulla debian senza incasianre tutto?
grazie