[Gentoo] Configurazione server X

[ANDY CAPS]

se avvii knoppix lo trovi in /etc/X11

[pinball]

guarda che te l'ha scritto... indirettamente ma te l'ha detto dove sta....

[sanxius]

Originariamente inviato da ANDY CAPS
se avvii knoppix lo trovi in /etc/X11

gia' fatto e ora mi sta rompendo l'anima con sto DRI

modprobe: Can't locate module agpgart
[drm] failed to load kernel module "agpgart"
....

[drm] failed to load kernel module "mga"

che du pall sta Matrox G400.. ho preso proprio una scheda video cazzuta.
strano...devo metterlo come modulo e non come incluso nel kernel???

faccio altre prove...

anyway thanks

[ANDY CAPS]

l'importante è che tu metta anche l'agp della tua mobo come modulo

stanno sotto l'agpgart

poi scrivilo in /etc/modules.autoload.d/il kernel che usi

[sanxius]

Originariamente inviato da ANDY CAPS
l'importante è che tu metta anche l'agp della tua mobo come modulo

stanno sotto l'agpgart

poi scrivilo in /etc/modules.autoload.d/il kernel che usi

mboh.... dentro /etc/modules.autoload.d/il kernel c'e' 2.4 e 2.6 e io sono alla ver 2.4.25
comunque non fa niente... strano che facendo solo X si pianta...mentre startx va

sicuro che e' disabilitato il DRI xche' non trova il modulo e li' non c'e' modo di saltarci su...
tento tento

SZ

[ANDY CAPS]

se hai il 2.4 lo devi scrivere nel kernel-2.4


leggi questa guida comunque
http://www.gentoo.it/doc/dri-howto.html

qui trovi tutto il necessario per il giovane matroxista

[sanxius]

Originariamente inviato da ANDY CAPS
l'importante è che tu metta anche l'agp della tua mobo come modulo

stanno sotto l'agpgart

poi scrivilo in /etc/modules.autoload.d/il kernel che usi

Originariamente inviato da ANDY CAPS
se hai il 2.4 lo devi scrivere nel kernel-2.4


leggi questa guida comunque
http://www.gentoo.it/doc/dri-howto.html

qui trovi tutto il necessario per il giovane matroxista

certo... quella guida li l'ho letta 200 volte...

pero' c'e' sta bega qua...
ricompilato riscritto...
e in /etc/modules.autoload.d/2.4.0 che ci scrivo???? vedo una fila di moduli... buh!

comunque domani all'univ mi prendo il secondo CD di packages (e l'ho scoperto stanotte) e ci faccio la installazione GRP.

Ciao e grazie SZ

[pinball]

devi scriverci dentro i nomi dei moduli che vuoi vengano caricati all'avvio.. non mi semrba difficile....

[ANDY CAPS]

ce li devi scrivere anche se fai un installazione grp
l'installazione da grp velocizza l'installazione ma la configurazione la devi fare come quella per lo stage 1


se mi incolli un dmesg e un lsmod ti posso dire cosa sciverci

per l'agp ad esempio io ho una mobo con via come chipset ho messo

via-agp



l'importante
prova anche


VIDEO_CARDS="mga" emerge xfree-drm

o
VIDEO_CARDS="matrox" emerge xfree-drm
dai un occhiata anche qui

http://forums.gentoo.org/viewtopic.p...deocard+matrox

[sanxius]

uhm... qualcosa qui non ha funzionato!!!stavo postando via linux... e mi chiede sempre di loggarmi....evidentemente w3m non e' il browser ideale per hwupg


allora...dmesg:

Linux version 2.4.25-gentoo-r1 (root@livecd) (gcc version 3.3.2 20031218 (Gentoo Linux 3.3.2-r5, propolice-3.3-7)) #2 Thu Jun 24 04:45:18 CEST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffec000 (usable)
BIOS-e820: 000000001ffec000 - 000000001ffef000 (ACPI data)
BIOS-e820: 000000001ffef000 - 000000001ffff000 (reserved)
BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 131052
zone(0): 4096 pages.
zone(1): 126956 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 ASUS ) @ 0x000f6a70
ACPI: RSDT (v001 ASUS A7V-133 0x30303031 MSFT 0x31313031) @ 0x1ffec000
ACPI: FADT (v001 ASUS A7V-133 0x30303031 MSFT 0x31313031) @ 0x1ffec080
ACPI: BOOT (v001 ASUS A7V-133 0x30303031 MSFT 0x31313031) @ 0x1ffec040
ACPI: DSDT (v001 ASUS A7V-133 0x00001000 MSFT 0x0100000b) @ 0x00000000
Kernel command line: BOOT_IMAGE=gentoo ro root=343
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 1410.242 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2811.49 BogoMIPS
Memory: 514260k/524208k available (2139k kernel code, 9564k reserved, 359k data, 160k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
Proc Config support by ptb@it.uc3m.es
proc config counted 9347 bytes in names
proc config counted 1035 bytes in value handles
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183fbff c1c7fbff 00000000 00000000
CPU: Common caps: 0183fbff c1c7fbff 00000000 00000000
CPU: AMD Athlon(tm) Processor stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1410.1721 MHz.
..... host bus clock speed is 268.6043 MHz.
cpu: 0, clocks: 2686043, slice: 1343021
CPU0<T0:2686032,T1:1343008,D:3,S:1343021,C:2686043>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20040116
PCI: PCI BIOS revision 2.10 entry at 0xf1180, last bus=1
PCI: Using configuration type 1
tbxface-0117 [03] acpi_load_tables : ACPI Tables successfully acquired
Parsing all Control Methods:...................................................................................................................
Table [DSDT](id F004) - 356 Objects with 38 Devices 115 Methods 24 Regions
ACPI Namespace successfully loaded at root c016d1bc
ACPI: IRQ9 SCI: Edge set to Level Trigger.
evxfevnt-0093 [04] acpi_enable : Transition to ACPI mode successful
evgpeblk-0747 [06] ev_create_gpe_block : GPE 00 to 15 [_GPE] 2 regs at 000000000000E420 on int 9
Completing Region/Field/Buffer/Package initialization:...........................................................
Initialized 24/24 Regions 2/2 Fields 19/19 Buffers 14/14 Packages (364 nodes)
Executing all Device _STA and_INI methods:........................................
40 Devices found containing: 40 _STA, 0 _INI methods
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 S5)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 89 & 1f -> 09
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 12
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
matroxfb: Matrox Millennium G400 MAX (AGP) detected
matroxfb: MTRR's turned on
matroxfb: 640x480x16bpp (virtual: 640x13104)
matroxfb: framebuffer at 0xE4000000, mapped to 0xe081c000, size 33554432
Console: switching to colour frame buffer device 80x30
fb0: MATROX VGA frame buffer device
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10f
Non-volatile memory driver v1.2
floppy0: no floppy controllers found
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Compaq SMART2 Driver (v 2.4.28)
HP CISS Driver (v 2.4.50)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:04.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:04.1
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hdaMA, hdbMA
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdcio, hddio
PDC20265: IDE controller at PCI slot 00:11.0
PDC20265: chipset revision 2
PDC20265: not 100% native mode: will probe irqs later
PDC20265: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
ide2: BM-DMA at 0x8800-0x8807, BIOS settings: hdeio, hdfMA
ide3: BM-DMA at 0x8808-0x880f, BIOS settings: hdgio, hdhio
hdb: C/H/S=0/0/0 from BIOS ignored
hda: JLMS XJ-HD163, ATAPI CD/DVD-ROM drive
hdb: IBM-DJNA-371350, ATA DISK drive
blk: queue c018809c, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 26520480 sectors (13578 MB) w/1966KiB Cache, CHS=26310/16/63, UDMA(33)
hda: attached ide-cdrom driver.
hda: ATAPI 48X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.12
Partition check:
/dev/ide/host0/bus0/target1/lun0: [PTBL] [1650/255/63] p1 p2 p3
ide: late registration of driver.
matroxfb_crtc2: secondary head of fb0 was registered as fb1
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 2147.200 MB/sec
32regs : 1384.800 MB/sec
pII_mmx : 3297.600 MB/sec
p5_mmx : 4234.800 MB/sec
raid5: using function: p5_mmx (4234.800 MB/sec)
md: multipath personality registered as nr 7
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
LVM version 1.0.8(17/11/2003)
device-mapper: 4.0.5-ioctl (2003-11-18) initialised: dm@uk.sistina.com
Initializing Cryptographic API
IEEE 802.2 LLC for Linux 2.1 (c) 1996 Tim Alpaerts
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
reiserfs: found format "3.6" with standard journal
reiserfs: checking transaction log (device ide0(3,67)) ...
for (ide0(3,67))
ide0(3,67):Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 160k freed
Adding Swap: 1004052k swap-space (priority -1)
spurious 8259A interrupt: IRQ7.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
8139too Fast Ethernet driver 0.9.26
PCI: Enabling device 00:0d.0 (0004 -> 0007)
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 at 0xa400, 00:e0:4c:55:3a:19, IRQ 5
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
8139cp: 10/100 PCI Ethernet driver v1.1 (Aug 30, 2003)
uhci.c: USB Universal Host Controller Interface driver v1.1
uhci.c: USB UHCI at I/O 0xd400, IRQ 5
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
uhci.c: USB UHCI at I/O 0xd000, IRQ 5
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport_pc: Via 686A parallel port: io=0x378
8139cp: 10/100 PCI Ethernet driver v1.1 (Aug 30, 2003)
8139cp: 10/100 PCI Ethernet driver v1.1 (Aug 30, 2003)
8139cp: 10/100 PCI Ethernet driver v1.1 (Aug 30, 2003)
8139cp: 10/100 PCI Ethernet driver v1.1 (Aug 30, 2003)
8139cp: 10/100 PCI Ethernet driver v1.1 (Aug 30, 2003)
8139cp: 10/100 PCI Ethernet driver v1.1 (Aug 30, 2003)
8139cp: 10/100 PCI Ethernet driver v1.1 (Aug 30, 2003)
8139cp: 10/100 PCI Ethernet driver v1.1 (Aug 30, 2003)
8139cp: 10/100 PCI Ethernet driver v1.1 (Aug 30, 2003)
8139cp: 10/100 PCI Ethernet driver v1.1 (Aug 30, 2003)
eth0: no IPv6 routers present

questo e' il lsmod

Module Size Used by Not tainted
parport_pc 25704 0
parport 23752 0 [parport_pc]
uhci 26204 0 (unused)
8139too 15240 1
mii 2272 0 [8139too]
usbcore 60460 1 [uhci]


Ciao e grasss

[ANDY CAPS]

in /etc/modules.autoload.d/kernel-2.4


devi mettere almeno

mga
agpgart
matroxfb
via-agp
via82cxxx_audio
ac97_codec

è da diversi mesi che non metto un kernel 2.4 e i nomi dei moduli non li ricordo se danno errore al boot puoi anche toglierli

sembra che tu non abbia besso i moduli della tua scheda audio nel kernel che dovrebbe essere un integrata via come la mia

eventualmente ricompila il kernel ed inserisci anche i moduli degli oss dal menu sound

dai un update-modules quando gli hai scritti nel file ed al riavvio dovrebbe funzionare