DFI UT P45-T2RS - Q9550s - Dominator 2x2 GB FSB WALL

Stevejedi · 02-08-2010, 17:37

Salve a tutti. Ho da poco sotto avuto sotto mano il q9550s assieme a delle nuove Dominator 2x2 GB prese per andare su di OC (prima avevo le xms2 a 800mhz). Vado benissimo su 3.4GHz (da testare in RS, ma promette molto bene), ma non riesco a superare i 400 MHz di FSB.
A 450 MHz passo il boot, ma si blocca durante il caricamento di Windows (la bandiera non si compone, o si blocca, o rimane vibrante in loop).
A 500 MHz (con moltiplicatore a 7x), il boot mi segnala 500x7, ma in Windows mi scende a 333x7. Strano!?!?!
EDIT: Appena provato a 533x6, boota su windows... ma sempre a 333x6. Assurdo

Che devo fare per salire di FSB??

Per un quadro completo vi posto la configurazione esatta:

DFI Lanparty UT P45-T2RS (bios aggiornato)
Intel Core 2 Quad Q9550s - Dissipatore Noctua NH-U12P - Pasta Diamond 7 Carati
Corsair Dominator Twin2x4096-8500C5D (2x CM2X2048-8500C5DF) rev 1.2 (chip PSC.F-Die 128MX8) 2x2GB
Sapphire 5850 Vapor-X 2GB
Western Digital Caviar Blue 400GB Sata II
Corsair HX 850W
Windows 7 Professional x64bit

Per evitare problemi legati alle periferiche usb utilizzo una tastiera PS/2 nel boot.

Vi porto i test che ho effettuato:
Test 1 = 400 x 8.5
Test 2 = 450 x 8.5

Test 1:

Ho raggiunto -semplicemente- un 400x8.5 con le RAM a 400MHz e timings rilassati. Con la seguente configurazione BIOS:

Genie BIOS Page

- BIOS Field

Exit Setup Shutdown……Mode 2
Shutdown After AC Loss……Enabled
AC Shutdown Free……Enabled
OC Fail Retry Counter……1
OC Fail CMOS Reload……Disabled
CPU Clock Ratio……8.5x
CPU N/2 Ratio……Enabled
Target CPU Clock……3400 MHz
CPU Clock……400 MHz
Boot Up Clock……Auto
CPU Clock Amplitude……800mV
CPU Clock0 Skew……0ps
CPU Clock1 Skew……0ps
DRAM Speed……400/800
Target DRAM Speed……DDR2 800
PCIE Clock……100 MHz
PCIE Slot Config……1X 1X

CPU Spread Spectrum……Disabled
PCIE Spread Spectrum……Disabled

- CPU Feature Page

Thermal Management Control……Disabled
PPM (EIST) Mode……Disabled
Limit CPUID MaxVal……Disabled
C1E Function……Disabled
Execute Disable Bit……Enabled
Virtualization Technology……Enabled
Core Multi Processing……Enabled

- DRAM Timing

Enhance Data Transmitting……Auto
Enhance Addressing……Auto
T2 Dispatch……Auto
Flex Memory Mode……Auto
Cas Latnecy Time (tCL)……Auto
RAS# to CAS# Delay (tCRD)……Auto
RAS# Precharge Time (tRP)……Auto
Precharge Delay (tRAS)……Auto
All Precharge to Act……Auto
REF to ACT Delay (tRFC)……Auto
Performance LVL (Read Delay)……Auto
Read delay phase adjust……N/A
Write to PRE Delay (tWR)……Auto
Rank Write to Read (tWTR)……Auto
ACT to ACT Delay (tRRD)……Auto
Read to Write Delay (tRDWR)……Auto
Ranks Write to Write (tWRWR)……Auto
Ranks Write to Read (tWRRD)……Auto
Read CAS# Precharge (tRTP)……Auto
All PRE to Refresh……Auto

- Clock Setting Fine Delay (tutti i valori si sono impostati automaticamente)

DLL and RCOMP Settings……Auto
CH1 DRAM Default Skew……Model 0
CH2 DRAM Default Skew……Model 0
RCOMP Setting…Model 0

Fine Delay Step Degree……70ps
Ch1 Clock Crossing Setting……Auto
DIMM1 Clock Fine Delay……2032ps
DIMM2 Clock Fine Delay……2032ps
Ch1 Control0 Fine Delay……234ps
Ch1 Control1 Fine Delay……234ps
Ch1 Control2 Fine Delay……234ps
Ch1 Control3 Fine Delay……234ps
Ch1 Command Fine Delay……344ps

Ch2 Clock Crossing Setting……Auto
DIMM3 Clock Fine Delay……1744ps
DIMM4 Clock Fine Delay……1744ps
Ch2 Control0 Fine Delay……42ps
Ch2 Control1 Fine Delay……42ps
Ch2 Control2 Fine Delay……42ps
Ch2 Control3 Fine Delay……42ps
Ch2 Command Fine Delay……344ps

Ch1Ch2 Common Clock Setting……Auto

Ch1 RDCAS GNT-Chip Delay……Auto
Ch1 WRCAS GNT-Chip Delay……Auto
Ch1 Command to CS Delay……Auto

Ch2 RDCAS GNT-Chip Delay…Auto
Ch2 WRCAS GNT-Chip Delay……Auto
Ch2 Command to CS Delay……Auto

- Read Delay Phase Adjust (tutti i valori si sono impostati automaticamente)

Ch1 Read Delay Phase (4~0)……7-7-7-7-7
Channel 1 Phase 0 Pull-in……Auto
Channel 1 Phase 1 Pull-in……Auto
Channel 1 Phase 2 Pull-in……Auto
Channel 1 Phase 3 Pull-in……Auto

Ch2 Read Delay Phase (4~0)……7-7-7-7-7
Channel 2 Phase 0 Pull-in……Auto
Channel 2 Phase 1 Pull-in……Auto
Channel 2 Phase 2 Pull-in……Auto
Channel 2 Phase 3 Pull-in……Auto

- Voltage Settings

CPU VID Control……Auto 1.1575 V (è il VID del processore)
CPU VID Special Add Limit……Enabled
CPU VID Special Add……Auto
DRAM Voltage Control……1.91V (in automatico è il valore impostato da bios sulle ram)
SB Core/CPU PLL Voltage……1.55V
NB Core Voltage……1.140V
CPU VTT Voltage……1.200V
Vcore Droop Control……Disabled
Clockgen Voltage Control……3.45V
GTL+ Buffers Strength……Strong
CPU GTL 0 REF Volt……0.6700
CPU GTL 1 REF Volt……0.6700
CPU GTL 2 REF Volt……0.6700
CPU GTL 3 REF Volt……0.6700
NB GTL 0 Ref Volt……0.6700
NB GTL 1 Ref Volt……0.6700
FSB Vref……Auto

________________________________________

Test 2 (450x8.5)

In grassetto i cambiamenti rispetto al precedente

Genie BIOS Page

- BIOS Field

Exit Setup Shutdown……Mode 2
Shutdown After AC Loss……Enabled
AC Shutdown Free……Enabled
OC Fail Retry Counter……1
OC Fail CMOS Reload……Disabled
CPU Clock Ratio……8.5x
CPU N/2 Ratio……Enabled
Target CPU Clock……3825 MHz
CPU Clock……450 MHz
Boot Up Clock……Auto
CPU Clock Amplitude……800mV
CPU Clock0 Skew……200ps
CPU Clock1 Skew……200ps
DRAM Speed……266/667
Target DRAM Speed……DDR2 1128
PCIE Clock……100 MHz
PCIE Slot Config……1X 1X

CPU Spread Spectrum……Disabled
PCIE Spread Spectrum……Disabled

- CPU Feature Page

Thermal Management Control……Disabled
PPM (EIST) Mode……Disabled
Limit CPUID MaxVal……Disabled
C1E Function……Disabled
Execute Disable Bit……Disabled
Virtualization Technology……Disabled
Core Multi Processing……Enabled

- DRAM Timing

Enhance Data Transmitting……Auto
Enhance Addressing……Auto
T2 Dispatch……Auto
Flex Memory Mode……Auto
Cas Latnecy Time (tCL)……Auto (provato anche con 5)
RAS# to CAS# Delay (tCRD)……Auto (provato anche con 5)
RAS# Precharge Time (tRP)……Auto (provato anche con 5)
Precharge Delay (tRAS)……Auto (provato anche con 15)
All Precharge to Act……Auto
REF to ACT Delay (tRFC)……Auto
Performance LVL (Read Delay)……Auto
Read delay phase adjust……N/A
Write to PRE Delay (tWR)……Auto
Rank Write to Read (tWTR)……Auto
ACT to ACT Delay (tRRD)……Auto
Read to Write Delay (tRDWR)……Auto
Ranks Write to Write (tWRWR)……Auto
Ranks Write to Read (tWRRD)……Auto
Read CAS# Precharge (tRTP)……Auto
All PRE to Refresh……Auto

- Clock Setting Fine Delay (i valori numerici si sono impostati automaticamente)

DLL and RCOMP Settings……Auto
CH1 DRAM Default Skew……Model 3
CH2 DRAM Default Skew……Model 3
RCOMP Setting…Model 1

Fine Delay Step Degree……70ps
Ch1 Clock Crossing Setting……More Relaxed (provato anche in Auto)
DIMM1 Clock Fine Delay……2396ps
DIMM2 Clock Fine Delay……2396ps
Ch1 Control0 Fine Delay……268ps
Ch1 Control1 Fine Delay……268ps
Ch1 Control2 Fine Delay……268ps
Ch1 Control3 Fine Delay……268ps
Ch1 Command Fine Delay……394ps

Ch2 Clock Crossing Setting……More Relaxed (provato anche in Auto)
DIMM3 Clock Fine Delay……2066ps
DIMM4 Clock Fine Delay……2066ps
Ch2 Control0 Fine Delay……48ps
Ch2 Control1 Fine Delay……48ps
Ch2 Control2 Fine Delay……48ps
Ch2 Control3 Fine Delay……48ps
Ch2 Command Fine Delay……394ps

Ch1Ch2 Common Clock Setting……More Relaxed (provato anche in Auto)

Ch1 RDCAS GNT-Chip Delay……Auto
Ch1 WRCAS GNT-Chip Delay……Auto
Ch1 Command to CS Delay……Auto

Ch2 RDCAS GNT-Chip Delay…Auto
Ch2 WRCAS GNT-Chip Delay……Auto
Ch2 Command to CS Delay……Auto

- Read Delay Phase Adjust (tutti i valori si sono impostati automaticamente)

Ch1 Read Delay Phase (4~0)……7-7-7-7-7
Channel 1 Phase 0 Pull-in……Auto
Channel 1 Phase 1 Pull-in……Auto
Channel 1 Phase 2 Pull-in……Auto
Channel 1 Phase 3 Pull-in……Auto

Ch2 Read Delay Phase (4~0)……7-7-7-7-7
Channel 2 Phase 0 Pull-in……Auto
Channel 2 Phase 1 Pull-in……Auto
Channel 2 Phase 2 Pull-in……Auto
Channel 2 Phase 3 Pull-in……Auto

- Voltage Settings

CPU VID Control……1.16250 V
CPU VID Special Add Limit……Enabled
CPU VID Special Add……Auto
DRAM Voltage Control……2.11V
SB Core/CPU PLL Voltage……1.75V
NB Core Voltage……1.408V
CPU VTT Voltage……1.303V
Vcore Droop Control……Disabled
Clockgen Voltage Control……3.45V
GTL+ Buffers Strength……Strong
CPU GTL 0 REF Volt……0.6700
CPU GTL 1 REF Volt……0.6700
CPU GTL 2 REF Volt……0.6700
CPU GTL 3 REF Volt……0.6700
NB GTL 0 Ref Volt……0.6700
NB GTL 1 Ref Volt……0.6700
FSB Vref……00

Stevejedi · 02-08-2010, 18:14

Curiosità. Sto provando pure FSB 567x6, ma se imposto PCIE Clock maggiore di 100MHz mi da errore 26 sulla scheda madre (problema alla scheda video) e si riavvia. Se imposto 100MHz di PCIE, va su windows ma a 333x6...

EDIT:

Sto facendo altre prove. Imposto l'FSB maggiore di 500, in questo caso 567x6, schermata di boot che conferma la frequenza, subito faccio partire Memtest86+.
Risultato:
FSB 333MHz
RAM 333MHz
CAS 5-5-7-18
Processore 2.0 GHz (333x6)

EDIT 2:

Anche con un solo banco installato fa lo stesso...

EDIT 3:

Operativo a 471MHz impostando il FSB vref a 00

02-08-2010, 17:37	#1
Stevejedi Senior Member Iscritto dal: Nov 2003 Città: Cosenza Messaggi: 1956	DFI UT P45-T2RS - Q9550s - Dominator 2x2 GB FSB WALL Salve a tutti. Ho da poco sotto avuto sotto mano il q9550s assieme a delle nuove Dominator 2x2 GB prese per andare su di OC (prima avevo le xms2 a 800mhz). Vado benissimo su 3.4GHz (da testare in RS, ma promette molto bene), ma non riesco a superare i 400 MHz di FSB. A 450 MHz passo il boot, ma si blocca durante il caricamento di Windows (la bandiera non si compone, o si blocca, o rimane vibrante in loop). A 500 MHz (con moltiplicatore a 7x), il boot mi segnala 500x7, ma in Windows mi scende a 333x7. Strano!?!?! EDIT: Appena provato a 533x6, boota su windows... ma sempre a 333x6. Assurdo Che devo fare per salire di FSB?? Per un quadro completo vi posto la configurazione esatta: DFI Lanparty UT P45-T2RS (bios aggiornato) Intel Core 2 Quad Q9550s - Dissipatore Noctua NH-U12P - Pasta Diamond 7 Carati Corsair Dominator Twin2x4096-8500C5D (2x CM2X2048-8500C5DF) rev 1.2 (chip PSC.F-Die 128MX8) 2x2GB Sapphire 5850 Vapor-X 2GB Western Digital Caviar Blue 400GB Sata II Corsair HX 850W Windows 7 Professional x64bit Per evitare problemi legati alle periferiche usb utilizzo una tastiera PS/2 nel boot. Vi porto i test che ho effettuato: Test 1 = 400 x 8.5 Test 2 = 450 x 8.5 Test 1: Ho raggiunto -semplicemente- un 400x8.5 con le RAM a 400MHz e timings rilassati. Con la seguente configurazione BIOS: Genie BIOS Page - BIOS Field Exit Setup Shutdown……Mode 2 Shutdown After AC Loss……Enabled AC Shutdown Free……Enabled OC Fail Retry Counter……1 OC Fail CMOS Reload……Disabled CPU Clock Ratio……8.5x CPU N/2 Ratio……Enabled Target CPU Clock……3400 MHz CPU Clock……400 MHz Boot Up Clock……Auto CPU Clock Amplitude……800mV CPU Clock0 Skew……0ps CPU Clock1 Skew……0ps DRAM Speed……400/800 Target DRAM Speed……DDR2 800 PCIE Clock……100 MHz PCIE Slot Config……1X 1X CPU Spread Spectrum……Disabled PCIE Spread Spectrum……Disabled - CPU Feature Page Thermal Management Control……Disabled PPM (EIST) Mode……Disabled Limit CPUID MaxVal……Disabled C1E Function……Disabled Execute Disable Bit……Enabled Virtualization Technology……Enabled Core Multi Processing……Enabled - DRAM Timing Enhance Data Transmitting……Auto Enhance Addressing……Auto T2 Dispatch……Auto Flex Memory Mode……Auto Cas Latnecy Time (tCL)……Auto RAS# to CAS# Delay (tCRD)……Auto RAS# Precharge Time (tRP)……Auto Precharge Delay (tRAS)……Auto All Precharge to Act……Auto REF to ACT Delay (tRFC)……Auto Performance LVL (Read Delay)……Auto Read delay phase adjust……N/A Write to PRE Delay (tWR)……Auto Rank Write to Read (tWTR)……Auto ACT to ACT Delay (tRRD)……Auto Read to Write Delay (tRDWR)……Auto Ranks Write to Write (tWRWR)……Auto Ranks Write to Read (tWRRD)……Auto Read CAS# Precharge (tRTP)……Auto All PRE to Refresh……Auto - Clock Setting Fine Delay (tutti i valori si sono impostati automaticamente) DLL and RCOMP Settings……Auto CH1 DRAM Default Skew……Model 0 CH2 DRAM Default Skew……Model 0 RCOMP Setting…Model 0 Fine Delay Step Degree……70ps Ch1 Clock Crossing Setting……Auto DIMM1 Clock Fine Delay……2032ps DIMM2 Clock Fine Delay……2032ps Ch1 Control0 Fine Delay……234ps Ch1 Control1 Fine Delay……234ps Ch1 Control2 Fine Delay……234ps Ch1 Control3 Fine Delay……234ps Ch1 Command Fine Delay……344ps Ch2 Clock Crossing Setting……Auto DIMM3 Clock Fine Delay……1744ps DIMM4 Clock Fine Delay……1744ps Ch2 Control0 Fine Delay……42ps Ch2 Control1 Fine Delay……42ps Ch2 Control2 Fine Delay……42ps Ch2 Control3 Fine Delay……42ps Ch2 Command Fine Delay……344ps Ch1Ch2 Common Clock Setting……Auto Ch1 RDCAS GNT-Chip Delay……Auto Ch1 WRCAS GNT-Chip Delay……Auto Ch1 Command to CS Delay……Auto Ch2 RDCAS GNT-Chip Delay…Auto Ch2 WRCAS GNT-Chip Delay……Auto Ch2 Command to CS Delay……Auto - Read Delay Phase Adjust (tutti i valori si sono impostati automaticamente) Ch1 Read Delay Phase (4~0)……7-7-7-7-7 Channel 1 Phase 0 Pull-in……Auto Channel 1 Phase 1 Pull-in……Auto Channel 1 Phase 2 Pull-in……Auto Channel 1 Phase 3 Pull-in……Auto Ch2 Read Delay Phase (4~0)……7-7-7-7-7 Channel 2 Phase 0 Pull-in……Auto Channel 2 Phase 1 Pull-in……Auto Channel 2 Phase 2 Pull-in……Auto Channel 2 Phase 3 Pull-in……Auto - Voltage Settings CPU VID Control……Auto 1.1575 V (è il VID del processore) CPU VID Special Add Limit……Enabled CPU VID Special Add……Auto DRAM Voltage Control……1.91V (in automatico è il valore impostato da bios sulle ram) SB Core/CPU PLL Voltage……1.55V NB Core Voltage……1.140V CPU VTT Voltage……1.200V Vcore Droop Control……Disabled Clockgen Voltage Control……3.45V GTL+ Buffers Strength……Strong CPU GTL 0 REF Volt……0.6700 CPU GTL 1 REF Volt……0.6700 CPU GTL 2 REF Volt……0.6700 CPU GTL 3 REF Volt……0.6700 NB GTL 0 Ref Volt……0.6700 NB GTL 1 Ref Volt……0.6700 FSB Vref……Auto ________________________________________ Test 2 (450x8.5) In grassetto i cambiamenti rispetto al precedente Genie BIOS Page - BIOS Field Exit Setup Shutdown……Mode 2 Shutdown After AC Loss……Enabled AC Shutdown Free……Enabled OC Fail Retry Counter……1 OC Fail CMOS Reload……Disabled CPU Clock Ratio……8.5x CPU N/2 Ratio……Enabled Target CPU Clock……3825 MHz CPU Clock……450 MHz Boot Up Clock……Auto CPU Clock Amplitude……800mV CPU Clock0 Skew……200ps CPU Clock1 Skew……200ps DRAM Speed……266/667 Target DRAM Speed……DDR2 1128 PCIE Clock……100 MHz PCIE Slot Config……1X 1X CPU Spread Spectrum……Disabled PCIE Spread Spectrum……Disabled - CPU Feature Page Thermal Management Control……Disabled PPM (EIST) Mode……Disabled Limit CPUID MaxVal……Disabled C1E Function……Disabled Execute Disable Bit……Disabled Virtualization Technology……Disabled Core Multi Processing……Enabled - DRAM Timing Enhance Data Transmitting……Auto Enhance Addressing……Auto T2 Dispatch……Auto Flex Memory Mode……Auto Cas Latnecy Time (tCL)……Auto (provato anche con 5) RAS# to CAS# Delay (tCRD)……Auto (provato anche con 5) RAS# Precharge Time (tRP)……Auto (provato anche con 5) Precharge Delay (tRAS)……Auto (provato anche con 15) All Precharge to Act……Auto REF to ACT Delay (tRFC)……Auto Performance LVL (Read Delay)……Auto Read delay phase adjust……N/A Write to PRE Delay (tWR)……Auto Rank Write to Read (tWTR)……Auto ACT to ACT Delay (tRRD)……Auto Read to Write Delay (tRDWR)……Auto Ranks Write to Write (tWRWR)……Auto Ranks Write to Read (tWRRD)……Auto Read CAS# Precharge (tRTP)……Auto All PRE to Refresh……Auto - Clock Setting Fine Delay (i valori numerici si sono impostati automaticamente) DLL and RCOMP Settings……Auto CH1 DRAM Default Skew……Model 3 CH2 DRAM Default Skew……Model 3 RCOMP Setting…Model 1 Fine Delay Step Degree……70ps Ch1 Clock Crossing Setting……More Relaxed (provato anche in Auto) DIMM1 Clock Fine Delay……2396ps DIMM2 Clock Fine Delay……2396ps Ch1 Control0 Fine Delay……268ps Ch1 Control1 Fine Delay……268ps Ch1 Control2 Fine Delay……268ps Ch1 Control3 Fine Delay……268ps Ch1 Command Fine Delay……394ps Ch2 Clock Crossing Setting……More Relaxed (provato anche in Auto) DIMM3 Clock Fine Delay……2066ps DIMM4 Clock Fine Delay……2066ps Ch2 Control0 Fine Delay……48ps Ch2 Control1 Fine Delay……48ps Ch2 Control2 Fine Delay……48ps Ch2 Control3 Fine Delay……48ps Ch2 Command Fine Delay……394ps Ch1Ch2 Common Clock Setting……More Relaxed (provato anche in Auto) Ch1 RDCAS GNT-Chip Delay……Auto Ch1 WRCAS GNT-Chip Delay……Auto Ch1 Command to CS Delay……Auto Ch2 RDCAS GNT-Chip Delay…Auto Ch2 WRCAS GNT-Chip Delay……Auto Ch2 Command to CS Delay……Auto - Read Delay Phase Adjust (tutti i valori si sono impostati automaticamente) Ch1 Read Delay Phase (4~0)……7-7-7-7-7 Channel 1 Phase 0 Pull-in……Auto Channel 1 Phase 1 Pull-in……Auto Channel 1 Phase 2 Pull-in……Auto Channel 1 Phase 3 Pull-in……Auto Ch2 Read Delay Phase (4~0)……7-7-7-7-7 Channel 2 Phase 0 Pull-in……Auto Channel 2 Phase 1 Pull-in……Auto Channel 2 Phase 2 Pull-in……Auto Channel 2 Phase 3 Pull-in……Auto - Voltage Settings CPU VID Control……1.16250 V CPU VID Special Add Limit……Enabled CPU VID Special Add……Auto DRAM Voltage Control……2.11V SB Core/CPU PLL Voltage……1.75V NB Core Voltage……1.408V CPU VTT Voltage……1.303V Vcore Droop Control……Disabled Clockgen Voltage Control……3.45V GTL+ Buffers Strength……Strong CPU GTL 0 REF Volt……0.6700 CPU GTL 1 REF Volt……0.6700 CPU GTL 2 REF Volt……0.6700 CPU GTL 3 REF Volt……0.6700 NB GTL 0 Ref Volt……0.6700 NB GTL 1 Ref Volt……0.6700 FSB Vref……00 __________________ Obsidian 550D \| Sabertooth Z77 \| 3770K \| Corsair CMD32GX3M4A2400C10 \| Palit Super JetStream GTX 1080 8GB \| HD0:Crucial MX300 2TB \| Corsair HX850W \| APC Back-UPS Pro 900 \| HP W2448HC \|\| MERCATINO + Feedbacks Ultima modifica di Stevejedi : 02-08-2010 alle 18:00.

02-08-2010, 18:14	#2
Stevejedi Senior Member Iscritto dal: Nov 2003 Città: Cosenza Messaggi: 1956	Curiosità. Sto provando pure FSB 567x6, ma se imposto PCIE Clock maggiore di 100MHz mi da errore 26 sulla scheda madre (problema alla scheda video) e si riavvia. Se imposto 100MHz di PCIE, va su windows ma a 333x6... EDIT: Sto facendo altre prove. Imposto l'FSB maggiore di 500, in questo caso 567x6, schermata di boot che conferma la frequenza, subito faccio partire Memtest86+. Risultato: FSB 333MHz RAM 333MHz CAS 5-5-7-18 Processore 2.0 GHz (333x6) EDIT 2: Anche con un solo banco installato fa lo stesso... EDIT 3: Operativo a 471MHz impostando il FSB vref a 00 __________________ Obsidian 550D \| Sabertooth Z77 \| 3770K \| Corsair CMD32GX3M4A2400C10 \| Palit Super JetStream GTX 1080 8GB \| HD0:Crucial MX300 2TB \| Corsair HX850W \| APC Back-UPS Pro 900 \| HP W2448HC \|\| MERCATINO + Feedbacks Ultima modifica di Stevejedi : 04-08-2010 alle 15:50.

Strumenti
Mostra una versione stampabile Invia questa pagina per email