|
|
|
![]() |
|
Strumenti |
![]() |
#1 |
Junior Member
Iscritto dal: Dec 2007
Messaggi: 12
|
Problemi di connessione!!! - Teleconomy Internet -
Ho un notebook toshiba con installato ubuntu 7.10 desktop alternate.
Grazie al gestore driver con restrizioni, ho abilitato il modem. Dopo aver dato i comandi nella riga di comando sudo apt-get update e sudo apt-get install gnome-ppp, ho configurato gnome-ppp, interrogando il modem che automaticamente ha trovato il dispositivo in /dev/ttySL0. Ho inserito il numero di connessione 7020187187, e telecom nei campi user e password. Ip dinamico. Dns automatico. Ecco il risultato dei log del modem: /home/fabio/.wvdial.conf<Warn>: Ignoring malformed input line: ";Do NOT edit this file by hand!" WvDial<*1>: WvDial: Internet dialer version 1.56 WvModem<*1>: Cannot get information for serial port. WvDial<*1>: Initializing modem. WvDial<*1>: Sending: ATZ WvDial Modem<*1>: ATZ WvDial Modem<*1>: OK WvDial<*1>: Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 WvDial Modem<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 WvDial Modem<*1>: OK WvDial<*1>: Modem initialized. WvDial<*1>: Sending: ATM1L3DT7020187187 WvDial<*1>: Waiting for carrier. WvDial Modem<*1>: ATM1L3DT7020187187 WvDial Modem<*1>: NO DIALTONE WvDial<Err>: No dial tone. WvDial<*1>: Disconnecting at Wed Dec 12 15:24:57 2007 Consigli per risolvere il problema? Grazie ![]() ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#2 | |
Messaggi: n/a
|
Quote:
Qua si va a scavare nei meandri della memoria, quando ci si collegava alle bbs e ai primi provider circa 12/13 anni fa... ![]() Il problema mi sembra che sia chiaro, "NO DIALTONE". Il problema dovrebbe stare nella stringa che passi prima del numero, nel tuo caso "ATM1L3DT", solo che mi sembra a "posto", perlomeno ci sono i comandi ATDT, il resto (M1L3) sta per? |
|
![]() |
![]() |
#3 |
Junior Member
Iscritto dal: Dec 2007
Messaggi: 12
|
Sono scoperto dal servizio adsl.
Ecco perche uso modem 56k con teleconomy internet. Comunque da quel che ho scritto volevo anche far intendere che ho configurato poche cose (completati i campi del gnome-ppp riferiti al numero telefonico, user e passord), conseguentemente le stringhe e ogni altra cosa son venute da sè (by ubuntu)... Spero di essermi spiegato. Quindi grazie per l'attenzione al mio post, ma non so dirti il significato di tutta la stringa. La gara alla scoperta della soluzione è ancora aperta ![]() ![]() ![]() ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#4 | |
Messaggi: n/a
|
Quote:
Cosí a naso il problema sta nella stringa che passi prima del numero, ATDT vuol dire "usa il dial tone" ma anche gli altri caratteri hanno un significato preciso. Devi trovare una legenda dei comandi AT e fare delle prove. La prima che farei é scrivere ATDT tutto attaccato e poi il numero da chiamare, senza altre stringhe. Ultima modifica di Lutra : 13-12-2007 alle 01:28. |
|
![]() |
![]() |
#5 |
Senior Member
Iscritto dal: Mar 2005
Città: /home/gica
Messaggi: 1653
|
Hai provato a cambiare alcune impostazioni di Gnome-ppp? Tipo "Ignora le stringhe da terminale" o "Utilizza modalità stupida", "Attendi il segnale di linea", ecc? Prova a modificarle una per volta e riprova!
![]()
__________________
gianluca@gicastation:~$ tar -c tar: Codardamente mi rifiuto di creare un archivio vuoto ![]() |
![]() |
![]() |
![]() |
#6 |
Junior Member
Iscritto dal: Dec 2007
Messaggi: 12
|
Grazie!
Ora sono di fretta e devo uscire, quando torno spero di riuscire a sviscerare ogni consiglio che mi hai dato! Spero ci sia solo da puntare/spuntare funzioni nella configurazione di gnome-ppp, e nulla di particolarmente complesso. ![]() ![]() ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#7 |
Junior Member
Iscritto dal: Dec 2007
Messaggi: 12
|
ECCO QUALCHE INFORMAZIONE IN PIU'
Nella scheda Setup Modem: dispositivo /dev/ttySL0 Tipo: modem analogico Velocità: 460800 Composizione: Toni Volume: Alto Tentativi di connessione: 3 Spuntato: Attendi il segnale di linea STRINGHE DI INIZIALIZZAZIONE: Init 2 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 Networking: Indirizzo Ip dinamico - Dns automatico In Opzioni: Spuntato: Abbandona la connessione se non cè tono di chiamata Controlla carrir line Controlla l'instradamento di default Non spuntato: Abbandona la connessione se la linea è occupata Abbandona la connessione se non cè tono di chiamata Ignora le stringhe del terminale (modo stupido) Invia risposta personalizzata Tempo di inattività prima della disconnessione 3 secondi QUESTE SON TUTTE LE INFORMAZIONI RIGUARDO LA CONFIGURAZIONE DEL MIO GNOME-PPPP. Consigli su cosa cambiare nelle stringhe, su cosa spuntare o non spuntare nelle ozioni??? Qualsiasi consiglio, spero utile, sarà ben accetto. Grazie |
![]() |
![]() |
![]() |
#8 |
Junior Member
Iscritto dal: Dec 2007
Messaggi: 12
|
Ho provato ad aggiungere ATX3 alla stringa di inizializzazione
Eccone il risultato del log del modem /home/fabio/.wvdial.conf<Warn>: Ignoring malformed input line: ";Do NOT edit this file by hand!" WvDial<*1>: WvDial: Internet dialer version 1.56 WvModem<*1>: Cannot get information for serial port. WvDial<*1>: Initializing modem. WvDial<*1>: Sending: ATZ WvDial Modem<*1>: ATZ WvDial Modem<*1>: OK WvDial<*1>: Sending: ATX3Q0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 WvDial Modem<*1>: ATX3Q0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 WvDial Modem<*1>: OK WvDial<*1>: Modem initialized. WvDial<*1>: Sending: ATM1L3DT7020187187 WvDial<*1>: Waiting for carrier. WvDial Modem<*1>: ATM1L3DT7020187187 WvDial Modem<*1>: NO CARRIER WvDial<Warn>: No Carrier! Trying again. WvDial<*1>: Sending: ATM1L3DT7020187187 WvDial<*1>: Waiting for carrier. WvDial Modem<*1>: ATM1L3DT7020187187 WvDial Modem<*1>: NO CARRIER WvDial<Warn>: No Carrier! Trying again. WvDial<*1>: Sending: ATM1L3DT7020187187 WvDial<*1>: Waiting for carrier. WvDial Modem<*1>: ATM1L3DT7020187187 WvDial Modem<*1>: NO CARRIER WvDial<Warn>: No Carrier! Trying again. WvDial<Warn>: Maximum Attempts Exceeded..Aborting!! WvDial<*1>: Disconnecting at Thu Dec 13 13:23:54 2007 Ultima modifica di FabioWWW : 13-12-2007 alle 12:28. |
![]() |
![]() |
![]() |
#9 |
Junior Member
Iscritto dal: Dec 2007
Messaggi: 12
|
Apro una parentesi: scusa Alexit ma posto ancora qui perchè credo, spero di essere a buon punto.
LA MIA STRINGA DI DEFAULT CON GNOME-PPP (AVEVO SOLO AGGIUNTO X3): ATX3Q0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 LA SOSTITUISCO CON +MS=90, eccone il risultato: /home/fabio/.wvdial.conf<Warn>: Ignoring malformed input line: ";Do NOT edit this file by hand!" WvDial<*1>: WvDial: Internet dialer version 1.56 WvModem<*1>: Cannot get information for serial port. WvDial<*1>: Initializing modem. WvDial<*1>: Sending: ATX3 WvDial Modem<*1>: ATX3 WvDial Modem<*1>: OK WvDial<*1>: Sending: ATX3Q0 V1 E1 S0=0 &C1 &D2 +MS=90 WvDial Modem<*1>: ATX3Q0 V1 E1 S0=0 &C1 &D2 +MS=90 WvDial Modem<*1>: OK WvDial<*1>: Modem initialized. WvDial<*1>: Sending: ATM1L3DT7020187187 WvDial<*1>: Waiting for carrier. WvDial Modem<*1>: ATM1L3DT7020187187 WvDial Modem<*1>: NO CARRIER WvDial<Warn>: No Carrier! Trying again. WvDial<*1>: Sending: ATM1L3DT7020187187 WvDial<*1>: Waiting for carrier. WvDial Modem<*1>: ATM1L3DT7020187187 WvDial Modem<*1>: NO CARRIER WvDial<Warn>: No Carrier! Trying again. WvDial<*1>: Sending: ATM1L3DT7020187187 WvDial<*1>: Waiting for carrier. WvDial Modem<*1>: ATM1L3DT7020187187 WvDial Modem<*1>: NO CARRIER WvDial<Warn>: No Carrier! Trying again. WvDial<Warn>: Maximum Attempts Exceeded..Aborting!! WvDial<*1>: Disconnecting at Mon Dec 17 07:43:46 2007 LA SOSTITUISCO CON +MS=34 /home/fabio/.wvdial.conf<Warn>: Ignoring malformed input line: ";Do NOT edit this file by hand!" WvDial<*1>: WvDial: Internet dialer version 1.56 WvModem<*1>: Cannot get information for serial port. WvDial<*1>: Initializing modem. WvDial<*1>: Sending: ATX3 WvDial Modem<*1>: ATX3 WvDial Modem<*1>: OK WvDial<*1>: Sending: ATX3Q0 V1 E1 S0=0 &C1 &D2 +MS=34 WvDial Modem<*1>: ATX3Q0 V1 E1 S0=0 &C1 &D2 +MS=34 WvDial Modem<*1>: OK WvDial<*1>: Modem initialized. WvDial<*1>: Sending: ATM1L3DT7020187187 WvDial<*1>: Waiting for carrier. WvDial Modem<*1>: ATM1L3DT7020187187 WvDial Modem<*1>: CONNECT 33600 WvDial<*1>: Carrier detected. Starting PPP immediately. WvDial<Notice>: Starting pppd at Mon Dec 17 07:44:55 2007 WvDial<Err>: Warning: Could not modify /etc/ppp/pap-secrets: Permission denied WvDial<Err>: --> PAP (Password Authentication Protocol) may be flaky. WvDial<Err>: Warning: Could not modify /etc/ppp/chap-secrets: Permission denied WvDial<Err>: --> CHAP (Challenge Handshake) may be flaky. WvDial<Notice>: Pid of pppd: 10802 WvDial<*1>: Using interface ppp0 WvDial<*1>: local IP address 80.104.224.93 WvDial<*1>: remote IP address 80.17.209.14 WvDial<*1>: primary DNS address 62.211.69.150 WvDial<*1>: secondary DNS address 212.48.4.15 --- Sfogliando SISTEMA-AMMINISTRAZIONE-RETE: Potrei tentare con Network Setting in Modem Connection Enable this connection ... ma ho lasciato perdere e ho ritentato con le stringhe. sudo gedit /etc/default/sl-modem-daemon ECCO IL RISULTATO, dovrei modificare qualcosa? # NOTE: settings in /etc/defautls/slmodemd are used too # set this to 1 to never run the daemon from the init script # you can set it if you have an USB device, than the init script won't # be started at boot (but when the USB device is plugged on) DONTSTART=0 # This is the default configuration for the slmodem driver daemon # running on Debian systems. # # Edit device node and country code here ... # # possible country codes are: # # USA # GERMANY # BELGIUM # etc. # # use 'slmodemd --countrylist' to check out other countries # # #SLMODEMD_DEVICE=slamr0 #SLMODEMD_COUNTRY=GERMANY SLMODEMD_DEVICE=auto SLMODEMD_COUNTRY=USA # # Additional options for slmodemd, see "slmodemd -h" output for details. # Do NOT set country or device name here! OPTS="" # force the start of the daemon even if old type modules seem to be # installed (set it to 1) FORCESTART=0 # set this to not see any hints of the init script on startup # BEQUIET=1 # set this to not create the /dev/modem symlink # NOSYMLINK=1 DOPO TUTTA QUESTI TEST e PROVE ECC... ho tentato seguendo la stringa ATQ0 V1 E1 X3 S0=0 +MS=34 e... /home/fabio/.wvdial.conf<Warn>: Ignoring malformed input line: ";Do NOT edit this file by hand!" WvDial<*1>: WvDial: Internet dialer version 1.56 WvModem<*1>: Cannot get information for serial port. WvDial<*1>: Initializing modem. WvDial<*1>: Sending: ATX3 WvDial Modem<*1>: ATX3 WvDial Modem<*1>: OK WvDial<*1>: Sending: ATQ0 V1 E1 X3 S0=0 +MS=34 WvDial Modem<*1>: ATQ0 V1 E1 X3 S0=0 +MS=34 WvDial Modem<*1>: OK WvDial<*1>: Modem initialized. WvDial<*1>: Sending: ATM1L3DT7020187187 WvDial<*1>: Waiting for carrier. WvDial Modem<*1>: ATM1L3DT7020187187 WvDial Modem<*1>: CONNECT 33600 WvDial<*1>: Carrier detected. Starting PPP immediately. WvDial<Notice>: Starting pppd at Mon Dec 17 08:08:01 2007 WvDial<Err>: Warning: Could not modify /etc/ppp/pap-secrets: Permission denied WvDial<Err>: --> PAP (Password Authentication Protocol) may be flaky. WvDial<Err>: Warning: Could not modify /etc/ppp/chap-secrets: Permission denied WvDial<Err>: --> CHAP (Challenge Handshake) may be flaky. WvDial<Notice>: Pid of pppd: 5951 WvDial<*1>: Using interface ppp0 WvDial<*1>: local IP address 80.104.222.175 WvDial<*1>: remote IP address 80.17.209.1 WvDial<*1>: primary DNS address 62.211.69.150 WvDial<*1>: secondary DNS address 212.48.4.15 Internet va! ma vedo che nei log da alcuni errori...Potete consigliarmi cosa migliore? E gnome-ppp m rimane aperto senza crearsi l'icona di notifica... Grazie! |
![]() |
![]() |
![]() |
#10 |
Junior Member
Iscritto dal: Dec 2007
Messaggi: 1
|
[SIS] AC'97 Modem - Problema con teleconomy 2
Ciao e scusate se mi intrometto.
Anche io ho problemi a connettermi con teleconomy e sono proprio agli inizi con Linux, quindi ho usato ScanModem per avere qualche informazione sul tipo di Modem che monta il mio Laptop (ASUS L3350M): PCI slot PCI ID SubsystemID Name ---------- --------- --------- -------------- 00:02.6 1039:7013 1043:1696 Modem: Silicon Integr. Systems [SiS] AC'97Modem Quindi un “Low level” driver snd-intel8x0m (ALSA) che dovrebbe essere affiancato da un slmodemd.gcc4.2 da compilare con ALSA support option. Quindi ho proceduto: #cp slmodemd /usr/sbin/slmodemd #chmod +x /usr/sbin/slmodemd # slmodemd --alsa -c ITALY modem:1 SmartLink Soft Modem: version 2.9.11 Nov 21 2007 09:03:10 symbolic link `/dev/ttySL0' -> `/dev/pts/1' created. modem `modem:1' created. TTY is `/dev/pts/1' Use `/dev/ttySL0' as modem device, Ctrl+C for termination. # wvdialconf /etc/wvdial.conf Editing `/etc/wvdial.conf'. Scanning your serial ports for a modem. ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. Modem Port Scan<*1>: S1 S2 S3 ttyS4<Info>: No such device or address Modem Port Scan<*1>: S4 ttyS5<Info>: No such device or address Modem Port Scan<*1>: S5 ttyS6<Info>: No such device or address Modem Port Scan<*1>: S6 ttyS7<Info>: No such device or address Modem Port Scan<*1>: S7 WvModem<*1>: Cannot get information for serial port. ttySL0<*1>: ATQ0 V1 E1 -- OK ttySL0<*1>: ATQ0 V1 E1 Z -- OK ttySL0<*1>: ATQ0 V1 E1 S0=0 -- OK ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK ttySL0<*1>: Modem Identifier: ATI -- SmartLink Soft Modem ttySL0<*1>: Speed 4800: AT -- OK ttySL0<*1>: Speed 9600: AT -- OK ttySL0<*1>: Speed 19200: AT -- OK ttySL0<*1>: Speed 38400: AT -- OK ttySL0<*1>: Speed 57600: AT -- OK ttySL0<*1>: Speed 115200: AT -- OK ttySL0<*1>: Speed 230400: AT -- OK ttySL0<*1>: Speed 460800: AT -- OK ttySL0<*1>: Max speed is 460800; that should be safe. ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK Found a modem on /dev/ttySL0. Modem configuration written to /etc/wvdial.conf. ttySL0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" Quindi ho ottenuto il seguente wvdial.conf [Dialer Defaults] Init1 = ATX3 Init2 = ATX3Q0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 #Init3 = ATX3 Modem = /dev/ttySL0 Phone = 7020187187 Idle Seconds = 300 Modem Type = Analog Modem #Stupid Mode = 1 Compuserve = 0 Baud = 460800 Auto DNS = 1 Dial Command = ATM1L3 DT Ask Password = 0 ISDN = 0 Password = telecom Username = telecom Carrier check = no Ha questo punto lasciando aperto su un terminale: # slmodemd --alsa -c ITALY modem:1 SmartLink Soft Modem: version 2.9.11 Nov 21 2007 09:03:10 symbolic link `/dev/ttySL0' -> `/dev/pts/1' created. modem `modem:1' created. TTY is `/dev/pts/1' Use `/dev/ttySL0' as modem device, Ctrl+C for termination. ho provato su un altro terminale a lanciare #wvdial --> WvDial: Internet dialer version 1.56 (abuild@mandelbrot) --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK --> Modem initialized. --> Idle Seconds = 300, disabling automatic reconnect. --> Sending: ATDT7020187187 --> Waiting for carrier. ATDT7020187187 --> Timed out while dialing. Trying again. --> Sending: ATDT7020187187 --> Waiting for carrier. --> Timed out while dialing. Trying again. --> Sending: ATDT7020187187 --> Waiting for carrier. Tra l'altro il modem non emette alcun segnale acustico, come invece succede se lo lancio con windows. Ha questo punto ho cercato di fare delle prove apportando delle variazioni a wvdial.conf, soprattutto sulla stringa Init2: Aggiungendo X3 dopo E1, oppure ATX3 e togliento Init3, oppure cambiando +FCLASS=0 con +MS=34 oppure +MS=90. Purtroppo quando lancio wvdial ottengo sempre lo stesso messaggio: Sending: ATDT7020187187 Waiting for carrier. Timed out while dialing. Trying again A questo punto non so veramente più cosa fare pertando ho pensato di aprire questo post con la speranza di trovare un aiuto. Grazie per l'attenzione. Amos |
![]() |
![]() |
![]() |
Strumenti | |
|
|
Tutti gli orari sono GMT +1. Ora sono le: 06:13.