Problema router philips cga7740n

[andreasder]

un amico ha questo problema, quando prova a disabilitare la connessione senza fili gli appare questa scritta, cosa può essere?

Grazie

[andreasder]

up

[alterpeople]

cari, ho alcuni problemi con un paio di router brandizzati come philips cga7740n ,

(è questo prodotto qui
http://www.p4c.philips.com/cgi-bin/d...&scy=it&slg=it

)

beh,dopo qualche minuto di contemplazione mi son deciso a smontarlo

ho attaccato un' interfaccia seriale col max3225e e mi son messo a smanettare.

Innanzitutto vediamo come fare l'interfaccia

il connettore che ci serve è praticamente identico all'apparato che vi linko qui di sotto

http://midge.vlad.org.ua/forum/viewt...fd25c81b5d73ef


veniamo a noi.
la configurazione della seriale deve essere

38400 ,8 ,n ,1

è possibile premendo 3 volte la barra spaziatrice ( dovete essere veloci ) accedere al bootloader quando l'apparato è in fase di avvio.
Una volta nel bootloader è possibile inviare via xmodem i file relativi all'area di memoria del firmware , della configurazione ,del bootloader stesso e/o dell'intera flash , anche se in giro loader e flash intera non si trovano , dovreste estrarli in jtag da un apparato funzionante.

Veniamo a noi.
Dopo vari tentativi di scrittura ed erase del firmware il mio problema rimane

o meglio l'apparato continua a riavviarsi all'infinito.
Vediamo cosa sputa in console.




=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2010.06.04 22:34:04 =~=~=~=~=~=~=~=~=~=~=~=


================
ROM VER: 1.0.3
CFG 01
Read EEPROMX
X




=======================================================================

Wireless ADSL Router AR7505QW 1-A-LF-B7 Loader V0.01 build Jun 29 2007 13:27:38

Arcadyan Technology Corporation

=======================================================================

MXIC MX29LV160B bottom boot 16-bit mode found


Copying boot params.....DONE


Press Space Bar 3 times to enter command mode ...

Flash Checking

Passed.


Unzipping firmware at 0x80002000 ... [ZIP 3] [ZIP 1] done

In c_entry() function ...

install_exception

Co config = 80008483

[INIT] Interrupt ...

init GPIO#3 (as0:0,as1:0,dir:1)

init GPIO#19 (as0:0,as1:0,dir:1)

init GPIO#5 (as0:0,as1:0,dir:1)

init GPIO#7 (as0:0,as1:0,dir:1)

init GPIO#30 (as0:0,as1:0,dir:0)

init GPIO#11 (as0:0,as1:0,dir:0)

gptu: totally 6 16-bit timers/counters

Init timer = 0

##### _ftext = 0x80002000

##### _fdata = 0x80343EA0

##### __bss_start = 0x803A7CDC

##### end = 0x80F828B0

##### Backup Data from 0x80343EA0 to 0x80F8A8B0~0x80FEE6EC len 409148

##### Backup Data completed

##### Backup Data verified

[INIT] System Log Pool startup ...

[INIT] MTinitialize ..

[INIT] usrclk

CPU Clock 333333334 Hz

mips_counter_frequency:166666667

r4k_offset: 00028b0a(166666)

init_US_counter : time1 = 260418 , time2 = 40260470, diff 40000052

US_counter = 48

cnt1 40984870 cnt2 40986122, diff 1252

Runtime code version: v0.13

System startup...

[INIT] Memory COLOR 0, 800000 bytes ..

[INIT] Memory COLOR 1, 600000 bytes ..

[INIT] Memory COLOR 2, 607200 bytes ..

MXIC MX29LV160B bottom boot 16-bit mode found

debug retVar= 1

Set flash memory layout to CMP_MACADDR: 00:1D:19:63:01:29

Boot Parameters found !!!

Bootcode version: V0.01

Serial number: J818045662

Hardware version: 01

MXIC MX29LV160B bottom boot 16-bit mode found



sizeof(struct III_Config_t) is 81876, nLen:81876, Magic:0x33343536

MXIC MX29LV160B bottom boot 16-bit mode found


my CFGVersionMagic = 33343536, old CFGVersionMagic on flash = 33343536

my CFGsize = 81888, my CFGDescSize = 16747

my Version = v0.13, Version on flash= v0.13

[CONFIG] flash version:[v0.13], [0.13.0-0]

[CONFIG] code version:[v0.13], [0.13.0-0]

CFGsize on flash = 81888, CFGDescSize on flash = 16747

MXIC MX29LV160B bottom boot 16-bit mode found

OldCfgHexSize:5987

Unzipping from 80631280 to 8062D104 ... [ZIP 1] done

Uncompressed size = 16745

Tail1 : END_III_Config_t


Size of Old CFG_DESC is :16745!!!

useCfgDesc:1

MyCfgHexSize:5987

Unzipping from 8062B988 to 8062780C ... [ZIP 1] done

Uncompressed size = 16745

My CFGDescSize:16747

useCfgDesc:1

Tail : END_III_Config_t


useCfgDesc:3


Restore Config file from ver:v0.13!!!


[CONFIG] Configuration in Flash is old version: 0.13.0

[CONFIG] DS_Tail:[t_CGA7740N]

!!! Invalid wireless channel range 0 ~ 0

!!! Use default value 1 ~ 11

default route: 0.0.0.0

BufferInit:

BUF_HDR_SZ=160 BUF_ALIGN_SZ=24 BUFFER_OFFSET=384

BUF_BUFSZ0=544 BUF_BUFSZ1=4320

NUM_OF_B0=0 NUM_OF_B1=1000

BUF_POOL0_SZ=0 BUF_POOL1_SZ=4480000

sizeof(BUFFER0)=704,sizeof(BUFFER1)=4480

*BUF0=0x80b47534 *BUF1=0x80701914

Altgn *BUF0=0x80b47540 *BUF1=0x80701920

End at BUF0:0x80b47540, BUF1:0x80b47520


BUF0[0]=0x80b47540 BUF1[0]=0x80701920


buffer0 pointer init OK!

buffer1 pointer init OK!

[qm_lnk_init] CLOCKHZ=1000 ...

[qm_lnk_init] add if 3 into QM link 0

[qm_cbq_enable] no QM attached

[qm_cbq_detach] no QM is attached at link 0

f=3492148201/100000, ns_per_byte=1090005888/100000

New cls: id=0, bw=8080 ns/byte, maxd=0 ms,

maxb=32, minb=2, avgpktsz=0, maxpktsz=0,

offtime=1, parent=0, borrow=0

pri=0, maxidle=1, minidle=0,

maxq=96, clsfg=17

f=2002645667/100000, ns_per_byte=1083109375/100000

New cls: id=1, bw=808080 ns/byte, maxd=0 ms,

maxb=16, minb=1, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f81bb8, borrow=80f81bb8

pri=7, maxidle=1, minidle=0,

maxq=48, clsfg=21

qm_cbq_attach(): cbqp->cbq_res=31

f=90439747/100000, ns_per_byte=1089990048/100000

New cls: id=2, bw=8162 ns/byte, maxd=0 ms,

maxb=32, minb=4, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f81bb8, borrow=80f81bb8

pri=0, maxidle=1, minidle=0,

maxq=96, clsfg=21

f=3846176767/100000, ns_per_byte=1072693248/100000

New cls: id=3, bw=799999999 ns/byte, maxd=0 ms,

maxb=16, minb=4, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f805b8, borrow=80f805b8

pri=0, maxidle=0, minidle=0,

maxq=96, clsfg=21

f=3846176767/100000, ns_per_byte=1072693248/100000

New cls: id=4, bw=799999999 ns/byte, maxd=0 ms,

maxb=16, minb=4, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f805b8, borrow=80f805b8

pri=2, maxidle=0, minidle=0,

maxq=48, clsfg=23

f=3846176767/100000, ns_per_byte=1072693248/100000

New cls: id=5, bw=799999999 ns/byte, maxd=0 ms,

maxb=16, minb=4, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f805b8, borrow=80f805b8

pri=3, maxidle=0, minidle=0,

maxq=48, clsfg=23

f=3846176767/100000, ns_per_byte=1072693248/100000

New cls: id=6, bw=799999999 ns/byte, maxd=0 ms,

maxb=16, minb=4, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f805b8, borrow=80f805b8

pri=4, maxidle=0, minidle=0,

maxq=48, clsfg=23

f=3846176767/100000, ns_per_byte=1072693248/100000

New cls: id=7, bw=799999999 ns/byte, maxd=0 ms,

maxb=16, minb=4, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f805b8, borrow=80f805b8

pri=5, maxidle=0, minidle=0,

maxq=48, clsfg=23

f=90439747/100000, ns_per_byte=1089990048/100000

New cls: id=8, bw=8162 ns/byte, maxd=0 ms,

maxb=16, minb=4, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f805b8, borrow=80f805b8

pri=7, maxidle=1, minidle=0,

maxq=48, clsfg=20

CLOCKHZ=1000

ifno= 0, Link_Type= 4

time = 08/01/2003, 00:00:00

TRAP(linkUp) : send ok!

Interface 0 ip = 127.0.0.1


ifno= 1, Link_Type= 1

vlan=0, vid=0, port_mask=0x0

DMA g_desc_list=0x80624640

Register=0x4012FFFF

init GPIO#6 (as0:0,as1:0,dir:1)

MAC Address: 00:1d:19:63:01:29

time = 08/01/2003, 00:00:00

TRAP(linkUp) : send ok!

Interface 1 ip = 192.168.2.1


ifno= 2, Link_Type= 1

PCI: Probing PCI hardware on host bus 0.

danube pci startup...

PCI clock 33.3MHz

DANUBE_GPIO_P1_ALTSEL0=85c7

DANUBE_GPIO_P1_ALTSEL1=0

DANUBE_GPIO_P1_DIR=81ee

Autoconfig PCI channel 0x80390660

Scanning bus 00, I/O 0x1ae00000:0x1b000001, Mem 0x18000000:0x1a000001

(bus:dev:fun)= 00:0e.0 Class 0280: VenID 18ff: DevID 06ff

Mem at 0x18000000 [size=0x10000]

Scanning bus 00:

Found 00:70 [18ff/06ff] 000280 00

Fixups for bus 00

Bus scan for 00 returning with max=00

6ff18ff 4300007 2800000 8000 18000000 0 0 0

0 0 ff80ff 28ff18ff 0 40 0 4020100


[HWLAN] ifno=2 irno=7 port=0x00000000

ifp->linkp->init(2) return non-Zero

ifno= 3, Link_Type= 1

PPE clear share buffer : 0xBE1A0000

ppe: ATM init succeeded

ATM_UBR

call ppe_open

alloc vpi = 8, vci = 35

ppe_dev.connection[1].vcc = 0x80EE24DC

ppe_open: QID 1, DMA 4

Init SAR ifno:3 g_atm_vcc[0] CONN:1 VPI/VCI:8/35

MAC Address: 00:1d:19:63:01:2b

Interface 3 ip = 0.0.0.0


ifno= 4, Link_Type= 0

ifno= 5, Link_Type= 0

ifno= 6, Link_Type= 0

ifno= 7, Link_Type= 0

ifno= 8, Link_Type= 0

ifno= 9, Link_Type= 0

ifno= 10, Link_Type= 0

ifno= 11, Link_Type= 136

IFLNK_PPPOE init : (Linkp)ifno = 11 idx = 2

IFLNK_PPPOE init : (Driverp)ifno = 11 idx = 3

ifp->linkp->init(11) return non-Zero

ifno= 12, Link_Type= 0

ifno= 13, Link_Type= 0

ifno= 14, Link_Type= 0

ifno= 15, Link_Type= 0

ifno= 16, Link_Type= 0

ifno= 17, Link_Type= 0

ifno= 18, Link_Type= 0

ifno= 19, Link_Type= 0

ruleCheck()> Group: 0, Error: Useless rule index will be truncated

ruleCheck()> Group: 1, Error: Useless rule index will be truncated

ruleCheck()> Group: 2, Error: Useless rule index will be truncated

CBAC rule format check succeed !!

reqCBACBuf()> init match pool, Have: 1000

Memory Address: 0x80f20a58 ~ 0x80f277d4

reqCBACBuf()> init timeGap pool, Have: 10000

Memory Address: 0x80f277d4 ~ 0x80f58528

reqCBACBuf()> init sameHost pool, Have: 2000

Memory Address: 0x80f58528 ~ 0x80f67f48

CBAC rule pool initialized !!

Init NAT data structure

RUNTASK id=2 if_task if0...

RUNTASK id=3 if_task if1...

RUNTASK id=4 if_task if2...

RUNTASK id=5 if_task if3...

RUNTASK id=6 timer_task...

RUNTASK id=7 conn_mgr...

RUNTASK id=8 main_8021x...

RUNTASK id=9 period_task...


========== ADSL Modem initialization OK ! ======


RUNTASK id=10 dhcp_daemon...

---[ HASH head start in 0xB0040000 ]---

---[ LZMA head start in 0xB011B800 ]---

[2] find PK at 0xB0135800

[3] find PK at 0xB0160400

Image[1] at 0xB0040000, len = 898590

Image[2] at 0xB011B800, len = 105960

Image[3] at 0xB0135800, len = 174289

Image[4] at 0xB0160400, len = 174289

Unzipping from B011B800 to 81EC2000 ... [ZIP 1] done

Uncompressed size = 883729

drive start addr[0]=81ec2000, [1]=81f99c20

[HTTPD] flash_init: failed!!

httpd: listen at 192.168.2.1:80

RUNTASK httpd...

RUNTASK id=13 dnsproxy...

RUNTASK id=14 snmp_task...

RUNTASK id=15 rip...

RUNTASK id=16 ripout...

RUNTASK id=17 dhcpd_mgmt_task...

UPnP is enabled

UPNP Device initialize success! slot=18

gConfig.WSC_Mode:1

RUNTASK id=19 wscmain...

RUNTASK id=20 wsc_Send_eap_packet...

RUNTASK id=21 wsc_Send_UPNP_packet...

RUNTASK id=22 WSC_WaitUserAction_Task...

gConfig.WSC_Mode:1

UART RX Input

Starting Multitask...

run_project_task

RUNTASK id=23 CMV_task...

RUNTASK id=24 UCPServer... (ProductType=6)

RUNTASK id=25 apAppInit...

[qm_outbnd_bw_update] ...

[qm_cbq_resetclst] n_totalcls=9

aft rst: id=0, bw=8080 ns/byte, maxd=0 ms,

maxb=32, minb=2, avgpktsz=0, maxpktsz=0,

offtime=1, parent=0, borrow=0

pri=0, maxidle=1, minidle=0,

maxq=96, clsfg=17

aft rst: id=1, bw=808080 ns/byte, maxd=0 ms,

maxb=16, minb=1, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f81bb8, borrow=80f81bb8

pri=7, maxidle=1, minidle=0,

maxq=48, clsfg=21

aft rst: id=2, bw=8162 ns/byte, maxd=0 ms,

maxb=32, minb=4, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f81bb8, borrow=80f81bb8

pri=0, maxidle=1, minidle=0,

maxq=96, clsfg=21

aft rst: id=3, bw=800000000 ns/byte, maxd=0 ms,

maxb=16, minb=4, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f805b8, borrow=80f805b8

pri=0, maxidle=0, minidle=0,

maxq=96, clsfg=21

aft rst: id=4, bw=800000000 ns/byte, maxd=0 ms,

maxb=16, minb=4, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f805b8, borrow=80f805b8

pri=2, maxidle=0, minidle=0,

maxq=48, clsfg=23

aft rst: id=5, bw=800000000 ns/byte, maxd=0 ms,

maxb=16, minb=4, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f805b8, borrow=80f805b8

pri=3, maxidle=0, minidle=0,

maxq=48, clsfg=23

aft rst: id=6, bw=800000000 ns/byte, maxd=0 ms,

maxb=16, minb=4, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f805b8, borrow=80f805b8

pri=4, maxidle=0, minidle=0,

maxq=48, clsfg=23

aft rst: id=7, bw=800000000 ns/byte, maxd=0 ms,

maxb=16, minb=4, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f805b8, borrow=80f805b8

pri=5, maxidle=0, minidle=0,

maxq=48, clsfg=23

aft rst: id=8, bw=8162 ns/byte, maxd=0 ms,

maxb=16, minb=4, avgpktsz=0, maxpktsz=0,

offtime=1, parent=80f805b8, borrow=80f805b8

pri=7, maxidle=1, minidle=0,

maxq=48, clsfg=20

Danube MEI version:1.00.07

get_datapump_address has been re-written

[qm_outbnd_bw_update] ok

===== General exception ======

EPC -> 0x80084080

CO_SR -> 0x0000FC03

Register Dump: Saved Area : Begin 0x805DC40C End 0x805DC5A7

RES:0x00000000

RA:0x800831F8

AT:0x803A0000

V0:0x00001008

V1:0x0000FC03

A0:0x00000000

A1:0x806E26AC

A2:0x00000000

T0:0x0000FC01

T1:0x00000000

T2:0x00000055

T3:0x0000002D

T4:0x00000020

T5:0x00000023

T6:0x00000000

T7:0x00000000

T8:0x00000001

T9:0x00000001

S0:0x00000000

S1:0x00000019

S2:0x00000064

S3:0x80083FCC

S4:0x80BB0000

S5:0x5EB5FBEA

S6:0x9FAFB95F

S7:0x6FD19A3A

S8:0xFA1DAB89

EPC:0x80084080

SR:0x0000FC03

CAUSE:0x00001008

Instruction : 0xAF82AC50

SP (Save Point) :0x805DC40C

==============================

SP (Real) :0x805DC6C8 : 0x0000005F

Stack Dump :

0x805DC6C8 : 0x0000005F

0x805DC6CC : 0x00000019

0x805DC6D0 : 0x00000064

0x805DC6D4 : 0x800831F8

0x805DC6D8 : 0x80008634

0x805DC6DC : 0x00000000

0x805DC6E0 : 0x00000000

0x805DC6E4 : 0x00000000

0x805DC6E8 : 0x00003A98

0x805DC6EC : 0x8000896C

0x805DC6F0 : 0x00000000

0x805DC6F4 : 0x00000000

0x805DC6F8 : 0x80009610

0x805DC6FC : 0x00000000

0x805DC700 : 0x00000000

0x805DC704 : 0x00000000

0x805DC708 : 0x00000000

0x805DC70C : 0x00000000

0x805DC710 : 0x00000000

0x805DC714 : 0x00000000

0x805DC718 : 0x00000000

0x805DC71C : 0x00000000

0x805DC720 : 0x00000000

0x805DC724 : 0x00000000

0x805DC728 : 0x00000000

0x805DC72C : 0x00000000

0x805DC730 : 0x803A0000

0x805DC734 : 0x00000000

0x805DC738 : 0x00000001

0x805DC73C : 0x00000000

0x805DC740 : 0x00000004

0x805DC744 : 0x00000000

0x805DC748 : 0x00000000

0x805DC74C : 0x00000000

0x805DC750 : 0x0000001F

0x805DC754 : 0x00000000

0x805DC758 : 0x00000000

0x805DC75C : 0x00000000

0x805DC760 : 0x00000000

0x805DC764 : 0x00000000

0x805DC768 : 0x0000FC01

0x805DC76C : 0x00000000

0x805DC770 : 0x00000000

0x805DC774 : 0x00000000

0x805DC778 : 0x00000055

0x805DC77C : 0x00000000

0x805DC780 : 0x0000002D

0x805DC784 : 0x00000000

0x805DC788 : 0x00000020

0x805DC78C : 0x00000000






#### a questo punto si rebootta ###


================
ROM VER: 1.0.3
CFG 01
Read EEPROMX
X




=======================================================================

Wireless ADSL Router AR7505QW 1-A-LF-B7 Loader V0.01 build Jun 29 2007 13:27:38

Arcadyan Technology Corporation

=======================================================================

MXIC MX29LV160B bottom boot 16-bit mode found


Copying boot params.....DONE


Press Space Bar 3 times to enter command mode ...

Flash Checking

Passed.

##### e via discorrendo ....
###############################

prova e riprova mi decido a cancellare l'area relativa alla configurazione , sempre tramite bootloader.

A questo punto il primo apparato parte , quindi dei 2 riesco a farne partire almeno uno.

In allegato c'è il log di quello che funziona , quindi divertitevi col diff !!! :D

no, dai alleggerisco il lavoro
uno si ferma a:


--non funzionante

Danube MEI version:1.00.07
get_datapump_address has been re-written
[qm_outbnd_bw_update] ok
====== General exception ======
EPC -> 0x80084080
CO_SR -> 0x0000FC03
Register Dump: Saved Area : Begin 0x805DC40C End 0x805DC5A7

bla ...bla ....















--funzionnate:



Danube MEI version:1.00.07
get_datapump_address has been re-written
[qm_outbnd_bw_update] ok
rt2860_open : should call request_irq ????????????????????????
rt2860_open 1
Image[1] at 0xB0040000, len = 898590
Image[2] at 0xB011B800, len = 105960
Image[3] at 0xB0135800, len = 174289
Image[4] at 0xB0160400, len = 174289
Image[3] is data pump.
Unzip DSP firmware ...
Unzipping from B0135800 to 80DD2400 ... [ZIP] rt2860_open 2
rt2860_init 1
rt2860_init 2
rt2860_init 3
rt2860_init 6
rt2860_init 7
rt2860_init 8
rt2860_init 9
rt2860_init 10
sizeof(RT2860AP_DAT) : 1314
sould check E2PROM MAC ?????????????????
rt2860_open 3
should Set up the Mac address ?????????
rt2860_open 4
rt2860_open 5
rt2860_open 6
netif_carrier_on() called ???
[htf_dbg] - OnlineActiveWirless() 862
should check capable(CAP_NET_ADMIN) ???
should check capable(CAP_NET_ADMIN) ???
should check capable(CAP_NET_ADMIN) ???
should check capable(CAP_NET_ADMIN) ???
should check capable(CAP_NET_ADMIN) ???
should check capable(CAP_NET_ADMIN) ???
should check capable(CAP_NET_ADMIN) ???
should check capable(CAP_NET_ADMIN) ???
should check capable(CAP_NET_ADMIN) ???
should check capable(CAP_NET_ADMIN) ???
should check capable(CAP_NET_ADMIN) ???
done
Uncompressed size = 301080
[dhcp_clt] close DHCP Clinet task, no interface needs dhcp client
*********************************************
Wi-Fi Simple Config Application - Intel Corp.
Version: Build 1.02, Mar 13 2008 12:11:07
*********************************************
Initializing stack...
---------in wsc init----------
----------sizeof(uint32)=4
----------sizeof(uint-long)=4
----------sizeof(uint32)=2
@#*@#*@#*EAP-WSC: Entered eap_wsc_init *#@*#@*#@
wsc_Send_eap_packet:udpFdupnp_wcn:2a;;udpFdupnp:2c
WSC_WaitUserAction:wait user action:0
update_img_hdr = A0DD2400
idx=0 mem_ptr=0xA0DD2400 size=65536
idx=1 mem_ptr=0xA0DE2400 size=65536
idx=2 mem_ptr=0xA0DF2400 size=65536
idx=3 mem_ptr=0xA0E02400 size=65536
idx=4 mem_ptr=0xA0E12400 size=38936
meiRunAdslModem() ok...
[HWLAN] [28] rapi_tmr_task running
[20]pthread_cond_init: 0
[20]pthread_mutex_init: resource No. 39
[20]pthread_mutex_init: resource No. 40
[PORTABLITY]:WscCreateThread--------------------
Entered udp_read
WscCmd:ActualCBThreadProc: Started
ADSL Firmware: 2.1.3.6.0.1 [Annex A:0x8105 0x0]
TRAP(coldStart) : send ok!
[20]pthread_cond_init: 1
[20]pthread_mutex_init: resource No. 41
[20]pthread_mutex_init: resource No. 42
[PORTABLITY]:WscCreateThread--------------------
WscCmd:ActualUIThreadProc: Started.
ActualUIThreadProc: wait q
ADSL> READY
MasterControl constructor
WscCmd::MC instantiated ok
[20]pthread_cond_init: 2
[20]pthread_mutex_init: resource No. 43
[20]pthread_mutex_init: resource No. 44
[PORTABLITY]:WscCreateThread--------------------
[20]pthread_mutex_init: resource No. 45
[PORTABLITY]:pthread_mutex_init--------------------
CTransport Construction
[20]pthread_cond_init: 3
[20]pthread_mutex_init: resource No. 46
[20]pthread_mutex_init: resource No. 47
[PORTABLITY]:WscCreateThread--------------------
In CTransport::ActualCBThreadProc
ActualCBThreadProc: Calling Dequeue
MC::Init: Init complete ok
WscCmd::MC intialized ok
WscCmd::Init ok, starting stack...
Info::ReadConfigFile: Called
Info::ReadConfigFile:?3??
Info::ReadConfigFile:File open ok
******************uuid_p:0x00000000000000011000001d19ca24d5*****
mp_deviceInfo->uuid[i]:
0-0-0-0-0-0-0-1-10-0-0-1d-19-ca-24-d5-
mp_deviceInfo->macAddr:00:1D:19:CA:24:D5
gSetting.dot1x.if_entry[0].enableWEP:0
authTypeFlags is 1 ,encrTypeFlags is 1 ,m_nwKey is , key len is 0
ssid is philips_install
S, 1342
E, 1591
RegistrarSM constructor
[20]pthread_cond_init: 4
[20]pthread_mutex_init: resource No. 48
[20]pthread_mutex_init: resource No. 49
[PORTABLITY]:WscCreateThread--------------------
[20]pthread_mutex_init: resource No. 50
[PORTABLITY]:pthread_mutex_init--------------------
RegistrarSM constructor
[20]pthread_cond_init: 5
[20]pthread_mutex_init: resource No. 51
[20]pthread_mutex_init: resource No. 52
[PORTABLITY]:WscCreateThread--------------------
c_devPwd:org:68557683
**************mcp_devPwd:68557683;;
Generated devPwd: ?`??
in startMonitor....
CInbEap Construction
Sizeof(WSC_NOTIFY_DATA) = -2141151024
---test--sizeof(WSC_NOTIFY_DATA) = 36
[20]pthread_cond_init: 6
[PORTABLITY]:WscCreateEvent--------------------
Entered udp_open
Socket open successful, sd: -2141151040
Entered udp_open
Socket open successful, sd: -2141151040
Entered udp_bind
Binding successful for socket [-2141151056]
[PORTABLITY]:WscCreateThread--------------------
In CInbEap::StaticRecvThread
CInbEap::ActualRecvThread Started
Entered udp_read
in startMonitor....
CInbUPnPDev Construction
Entered udp_open
Socket open successful, sd: -2141151040
Entered udp_open
Socket open successful, sd: -2141151040
Entered udp_bind
Binding successful for socket [-2141151056]
CInbUPnPDev StartMonitor
[PORTABLITY]:WscCreateThread--------------------
MC::SwitchModeOn: Exit
In CInbUPnPDev::StaticUPnPThread
end UPnPCreateMicroStack
Entered udp_read
MC::StartStack: Informing app of mode
-WscCmd::CallbackProc Enqueue done
MC::SwitchModeOn: Done callback
exit wscmain
@@[11]pthread_mutex_unlock: the res is free 39-- -2142290964
WscCmd:ActualCBThreadProc: CB_MAIN_PUSH_MODE recd

******* MODE: Access Point *******
-@@[26]pthread_mutex_unlock: the res is free 41-- -2142290364
*******p_header->eType:1

Options:
0. Quit
1. Get configured
2. Get configured via push-button
3. Get configured using IEs
Enter selection: ***gp_mc->mp_info->GetSwitchMode():1
mp_info->GetSwitchMode():1:e_currMode:1,,e_targetMode:3
mp_deviceInfo->authTypeFlags:1
mp_deviceInfo->encrTypeFlags:1
********cp_devPwd:68557683*****
mp_deviceInfo->authTypeFlags:1
mp_deviceInfo->encrTypeFlags:1
MC::SetBeaconIE: call to trans->SetBeaconIE() ok
MC::SetProbeRespIE: call to trans->SetProbeRespIE() ok
Waiting for Registrar to connect...
WscCmd::unconfig initiated
ActualUIThreadProc: wait q
[reset_802dot1x] wireless module ready
[init_wpa] dot1x_ready[0]=1
[reset_802dot1x] 802.1Xv2 ready
upnp_Init: flag=0
SSDP Initialization completed...
GenaInit : event_hook is NULL!!

[alterpeople]

sembra che il problema accada quando viene caricato il modulo della wireless.

Forza , gente , datemi una mano pls.

[Harry_Callahan]

Originariamente inviato da alterpeople

sembra che il problema accada quando viene caricato il modulo della wireless.

Forza , gente , datemi una mano pls.

la vedo difficile, nessuno dal 2009 ha risposto a andreasder

[alterpeople]

io nel frattempo vado avanti.
Se trovo altro lo posto , ma in giro non c'è niente , o quasi.
Probabilmente dovrò estrarmi in jtag il contenuto intero della flash per guardarci dentro.
Altra prova che posso fare ( mi è venuto in mente ma era sera tardi per attuarlo ) è spegnere sul rt funzionante la wireless, scaricare la conf e caricarla via bootloader su quello che si riavvia , anche se credo che carichi comunque il modulo senza accenderla.
Del resto non è molto diverso dagli altri embeeded device , anzi ... hihhi
vi farò sapere.

AlterPeoPle

[continuum666]

come è finita poi?

[Herbie_53]

Io ho un modem che a quanto pare è praticamente la fotocopia... sto facendo dei confronti tra i firmware e fino ad ora sembrano molto simili.. se c'è ancora qualcuno interessato si faccia vivo!