FreeBSD:partenza di X

[gokan]

Salve, ho installato poco fa FreeBSD 4.8. L'installazione è andata a buon fine.Il problema è adesso far partire X
Ho quella schifosa scheda che prende il nome di Kiro e come ben saprete fino a qualche tempo fa era parecchio ostica anche sotto linux.
Ho provato a far partire xf86cfg ma non funziona, allora ho provato a settare il tutto con xf86confi scegliendo come al solito Vesa generic (cosi faccio sotto linux all'atto dell'installazione), selezionato il monitor,etc.
In pratica alla fine ho creato tale file /etc/X11/XF86Config:


# File generated by xf86config.

#
# Copyright (c) 1999 by The XFree86 Project, Inc.
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
# THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
#
# Except as contained in this notice, the name of the XFree86 Project shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from the
# XFree86 Project.
#

# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of
# this file.
# **********************************************************************

# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

Load "dbe" # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection

# This loads the Type1 and FreeType font modules
Load "type1"
Load "speedo"
# Load "freetype"
# Load "xtt"

# This loads the GLX module
# Load "glx"
# This loads the DRI module
# Load "dri"

EndSection

# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.

RgbPath "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#

FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
# FontPath "/usr/X11R6/lib/X11/fonts/TrueType/"
# FontPath "/usr/X11R6/lib/X11/fonts/freefont/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"

# The module search path. The default path is shown here.

# ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

# Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.

# Option "DontVTSwitch"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

# Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.

# Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

# Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

# Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

# Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

# Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

Identifier "Keyboard1"
Driver "Keyboard"

# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

# Option "Protocol" "Xqueue"

Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"

# Option "LeftAlt" "Meta"
# Option "RightAlt" "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"

# These are the default XKB settings for XFree86
# Option "XkbRules" "xfree86"
# Option "XkbModel" "pc101"
# Option "XkbLayout" "us"
# Option "XkbVariant" ""
# Option "XkbOptions" ""

# Option "XkbDisable"

Option "XkbRules" "xfree86"
Option "XkbModel" "pc102"
Option "XkbLayout" "it"

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "PS/2"
Option "Device" "/dev/sysmouse"

# Mouse-speed setting for PS/2 mouse.

# Option "Resolution" "256"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

# Option "Protocol" "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

# Option "BaudRate" "9600"
# Option "SampleRate" "150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

Option "Emulate3Buttons"
# Option "Emulate3Timeout" "50"

# ChordMiddle is an option for some 3-button Logitech mice

# Option "ChordMiddle"

EndSection


# **********************************************************************
# Other input device sections
# this is optional and is required only if you
# are using extended input devices. This is for example only. Refer
# to the XF86Config man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice"
# Identifier "Mouse2"
# Driver "mouse"
# Option "Protocol" "MouseMan"
# Option "Device" "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball"
# Driver "magellan"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball2"
# Driver "spaceorb"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen0"
# Driver "microtouch"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "1412"
# Option "MaxX" "15184"
# Option "MinY" "15372"
# Option "MaxY" "1230"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen1"
# Driver "elo2300"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "231"
# Option "MaxX" "3868"
# Option "MinY" "3858"
# Option "MaxY" "272"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonThreshold" "17"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

Identifier "daewoo"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

HorizSync 31.5 - 64.3

# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

VertRefresh 50-160

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"

# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.

# Chipset "generic"

# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

Driver "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.

# BusID "PCI:0:10:0"

# VideoRam 256

# Clocks 25.2 28.3

EndSection

# Device configured by xf86config:

Section "Device"
Identifier "kiro"
Driver "vesa"
#VideoRam 65536
# Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen 1"
Device "kiro"
Monitor "daewoo"
DefaultDepth 16

Subsection "Display"
Depth 8
Modes "1280x1024" "1024x768" "800x600" "640x480"
ViewPort 0 0
Virtual 1600 1280
EndSubsection
Subsection "Display"
Depth 16
Modes "1024x768"
ViewPort 0 0
Virtual 1280 1024
EndSubsection
Subsection "Display"
Depth 24
Modes "1280x1024" "1024x768" "800x600" "640x480"
ViewPort 0 0
Virtual 1152 900
EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
Identifier "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.

Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"

EndSection

# Section "DRI"
# Mode 0666
# EndSection


Mi date qualche dritta su come sistemarlo per bene? Che ne dite se piazzo una versione del file tipo quella che uso con linux?
Ad esempio penso che la sezione DRI non dovrebbe essere commentata, dico bene?
Grazie in anticipo

[AnonimoVeneziano]

Fai partire xf86cfg direttamente da root , e non farlo partire normalmente con "xf86cfg" , ma con il comando :

xf86cfg -textmode

E' molto + comodo che la versione grafica .

Deve perforza funzionare se X è installato

Ciao

[gokan]

Originariamente inviato da AnonimoVeneziano
Fai partire xf86cfg direttamente da root , e non farlo partire normalmente con "xf86cfg" , ma con il comando :

xf86cfg -textmode

E' molto + comodo che la versione grafica .

Deve perforza funzionare se X è installato

Ciao

Effettivamente con con questo tipo di configurazione le cose sono più semplici, ho visto che alla fin fine avevo fatto lo stesso con xfc86config , purtroppo continua a non funzionare
Allego il file /var/log....

[cagnaluia]

.... ok, lho installato pure io e il server X, parte qualche piccolo errore, parte tranquillamente.


ho una piccola cosuccia adesso da vedere...

durante l'installazione ho tralasciato la configuraione della rete...

Come faccio per ripeterla... voglio dire.... come faccio per vedere la scheda di rete.. configurarla... darle il supporto per tcp/ip, ip, gateway, dns... insomma mettere il PC con FreeBSD in una rete di computer Winshit....



Grazie 1000

[Pang]

Originariamente inviato da cagnaluia
.... ok, lho installato pure io e il server X, parte qualche piccolo errore, parte tranquillamente.


ho una piccola cosuccia adesso da vedere...

durante l'installazione ho tralasciato la configuraione della rete...

Come faccio per ripeterla... voglio dire.... come faccio per vedere la scheda di rete.. configurarla... darle il supporto per tcp/ip, ip, gateway, dns... insomma mettere il PC con FreeBSD in una rete di computer Winshit....



Grazie 1000

sysinstall

Ciao

[AnonimoVeneziano]

Comunque , gokan, il log non riporta alcun problema , ora, o è il driver vesa che fa a botte con il server X o non so .

Comunque usa xf86cfg -textmode , deve funzionare per forza.

Ciao

[gokan]

Originariamente inviato da AnonimoVeneziano
Comunque , gokan, il log non riporta alcun problema , ora, o è il driver vesa che fa a botte con il server X o non so .

Comunque usa xf86cfg -textmode , deve funzionare per forza.

Ciao

Riproverò, anche se non penso possa cambiare tanto.
Grazie lo stesso.

[gokan]

Prima di tutto, mi sembra di avere lo stretto indispensabile per fare partire X
>>pkg_info
Mesa-3.4.2_2 A graphics library similar to SGI's OpenGL
XFree86-4.3.0,1 X11/XFree86 core distribution (complete, using mini/meta-po
XFree86-FontServer-4.3.0 XFree86-4 font server
XFree86-Server-4.3.0_2 XFree86-4 X server and related programs
XFree86-clients-4.3.0_1 XFree86-4 client programs and related files
XFree86-documents-4.3.0 XFree86-4 documentation
XFree86-font100dpi-4.3.0 XFree86-4 bitmap 100 dpi fonts
XFree86-font75dpi-4.3.0 XFree86-4 bitmap 75 dpi fonts
XFree86-fontCyrillic-4.3.0 XFree86-4 Cyrillic fonts
XFree86-fontDefaultBitmaps-4.3.0 XFree86-4 default bitmap fonts
XFree86-fontEncodings-4.3.0 XFree86-4 font encoding files
XFree86-fontScalable-4.3.0 XFree86-4 scalable fonts
XFree86-libraries-4.3.0_1 XFree86-4 libraries and headers
Xft-2.1_3 A client-sided font API for X applications
afterstep-1.0_1 Window manager originally based on the Bowman NeXTSTEP clon
arts-1.1,1 Audio system for the KDE integrated X11 desktop
asclock-1.0 Afterstep clock with some language extentions
cups-base-1.1.18.0_4 The Common UNIX Printing System: headers, libs, & daemons
esound-0.2.29 A sound library for enlightenment package
expat-1.95.6_1 XML 1.0 parser written in C
fam-2.6.9_2 A file alteration monitor
fontconfig-2.1_6 An XML-based font configuration API for X Windows
freetype2-2.1.3_1 A free and portable TrueType font rendering engine
gettext-0.11.5_1 GNU gettext package
imake-4.3.0 Imake and other utilities from XFree86
jpeg-6b_1 IJG's jpeg compression utilities
kde-3.1 The "meta-port" for KDE
kdebase-3.1_1 This package provides the basic applications for the KDE sy
kdegames-3.1 Games for the KDE integrated X11 desktop
kdegraphics-3.1 Graphics utilities for the KDE3 integrated X11 desktop
kdelibs-3.1 This is the base set of libraries needed by KDE programs
kdemultimedia-3.1 Multimedia utilities for the KDE integrated X11 desktop
kdenetwork-3.1 Network-related programs and modules for KDE
kdeutils-3.1 Utilities for the KDE integrated X11 desktop
koffice-1.2.1,1 Office Suite for KDE3
lcms-1.09 Light Color Management System -- a color management library
libart_lgpl2-2.3.11 Library for high-performance 2D graphics
libaudiofile-0.2.3 A sound library for SGI audio file
libgnugetopt-1.2 GNU getopt library
libiconv-1.8_2 A character set conversion library
libmng-1.0.4 Multiple-image Network Graphics (MNG) reference library
libogg-1.0_1,3 Ogg bitstream library
libvorbis-1.0_1,3 Audio compression codec library
libxml2-2.5.4 Xml parser library for GNOME
libxslt-1.0.27 The XSLT C library for GNOME
linux_base-7.1_2 The base set of packages needed in Linux mode
pcre-3.9 Perl Compatible Regular Expressions library
pkgconfig-0.15.0 An utility used to retrieve information about installed lib
png-1.2.5_2 Library for manipulating PNG images
python-2.2.2_2 An interpreted object-oriented programming language
qt-3.1.1_4 A C++ X GUI toolkit
tiff-3.5.7 Tools and library routines for working with TIFF images
uulib-0.5.18 A library for uu/xx/Base64/BinHex/yEnc de-/encoding
wrapper-1.0_2 Wrapper for XFree86-4 server
xanim-2.92.0 Play most popular animation formats and show pictures


Quando faccio startx mi da l'errore di "No Screens Found", cio non dovrebbe succedere dal momento che ho controllato che il file XF86Config è ben settato (xf86cfg docet).
Che ne dite?