|
|||||||
|
|
|
 |
|
|
Strumenti |
02-05-2012, 11:18
|
#1 |
|
Member
Iscritto dal: Feb 2010
Messaggi: 286
|
Aiuto overclock e8600 su dfi utx48t3rs
Ciao ragazzi come da descrizione..chiedo aiuto per clokkare il mio e8600 su questa mobo dfi utx48t3rs ho provato a cambiare 1000 parametri ma niente nn sale.. si riavvia ..crasha qualcuno può aiutarmi?
La mia cfg è mainboard è dfi utx48t3rs memorie ocz platinum 2+2 4 gb ddr 2000mhz processore e8600 di seguito posto il bios template: [code] DFI UT X48-T3RS LanParty CPU Feature - Thermal Management Control: Disabled - PPM(EIST) Mode: Disabled - Limit CPUID MaxVal: Disabled - CIE Function: Disabled - Execute Disable Bit: Disabled - Virtualization Technology: Disabled - Core Multi-Processing: Enabled Exist Setup Shutdown: Mode 2 Shutdown after AC Loss: Disabled O.C. Fail retry Counter: 0 CPU Clock Ratio: 10x CPU N/2 ratio: Disabled Target CPU Clock: 3600MHz CPU Clock: 400MHz Boot Up Clock: Auto CPU Clock Amplitude: 800mV CPU Clock0 Skew: 0ps CPU Clock1 Skew: 0ps DRAM Speed: 400/1333 Target DRAM SpeedDR3 1333 PCIE Clock: 100mhz PCIE Slot Config: 1X 1X CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled Voltage Settings CPU VID Control: Auto 1.2200V CPU VID Special Add Limit: Enabled CPU VID Special Add: Auto DRAM Voltage Control: 1.510V SB Core/CPU PLL Voltage: 1.510V NB Core Voltage: 1.291V CPU VTT Voltage: 1.100V Vcore Droop Control: Enabled Clockgen Voltage Control: 3.45v GTL+ Buffers Strength: Strong Host Slew Rate: Weak x MCH RON Offset Value: 00 x MCH RTT Offset Value: 00 x MCH Slew Rate Offset Value: 00 x MCH VREF 1 Value x MCH VREF 2 Value x MCH VREF 3 Value GTL REF Voltage Control: Disable x CPU GTL1/3 REF Volt: 113 x CPU GTL 0/2 REF Volt: 100 x North Bridge GTL REF Volt: 100 CPU Core Voltage: 1.20V DRAM Voltage: 1.50V NB Core Voltage: 1.32V CPU VTT Voltage: 1.10V DRAM Timing - Enhance Data transmitting: AUTO - Enhance Addressing: AUTO - T2 Dispatch: Auto Clock Setting Fine Delay: Press Enter CAS Latency Time (tCL): 9 RAS# to CAS# Delay (tRCD): 9 RAS# Precharge (tRP): 9 Precharge Delay (tRAS): 24 All Precharge to Act: AUTO REF to ACT Delay (tRFC): AUTO Performance LVL (Read Delay): AUTO Read delay phase adjust: Press Enter MCH ODT Latency: AUTO Write to PRE Delay (tWR): AUTO Rank Write to Read (tWTR): AUTO ACT to ACT Delay (tRRD): AUTO Read to Write Delay (tRDWR): AUTO Ranks Write to Write (tWRWR): AUTO Ranks Read to Read (tRDRD): AUTO Ranks Write to Read (tWRRD): AUTO Read CAS# Precharge (tRTP): AUTO ALL PRE to Refresh: AUTO DRAM CLK Driving Strength: Level 6 DRAM Data Driving Strength: Level 8 Ch1 DLL Default Skew Model: Model 0 Ch2 DLL Default Skew Model: Model 0 Fine Delay Step Degree: 5ps Ch1 Clock Crossing Setting: AUTO - DIMM 1 Clock fine delay: Current 489ps - DIMM 2 Clock fine delay: Current 489ps - DIMM 2 Control Fine Delay: Current 434ps - DIMM 1 Control Fine Delay: Current 473ps - Ch 1 Command fine delay: Current 560ps Ch2 Clock Crossing Setting: AUTO - DIMM 3 Clock fine delay: Current 686ps - DIMM 4 Clock fine delay: Current 686ps - DIMM 4 Control Fine Delay: Current 607ps - DIMM 3 Control Fine Delay: Current 654ps - Ch 2 Command fine delay: Current 693ps Ch1Ch2 CommonClock Setting: Auto Ch1 RDCAS GNT-Chip Delay: Auto Ch1 WRCAS GNT-Chip Delay: Auto Ch1 Command to CS Delay: Auto Ch2 RDCAS GNT-Chip Delay: Auto Ch2 WRCAS GNT-Chip Delay: Auto Ch2 Command to CS Delay: Auto Common CMD to CS Delay: Auto Qualccuno mi aiuti nn ce la faccio + sono settimane che smanetto ((
__________________
Trattative concluse positivamente con: Fabiox87x, irendul, Stappern , faUguale |
|
|
|
|
| Strumenti | |
|
|
Tutti gli orari sono GMT +1. Ora sono le: 19:38.
