Potenziamento hardware

[unascarpa]

Salve a tutti,
oramai devo prendere un pc nuovo, ma volevo anche per non sprecare un pc, potenziare il mio attuale.
Quindi diciamo che avevo pensato di spendere un 100 euro per upgradare questo harware.

innanzitutto ho un Intel Core i7 3632QM, attualemente con un HDD da 500Gb e monto Ubuntu 18.04 in dual boot con windowz.


Per quanto riguarda il disco rigido, passerò ad un ssd montato al posto del HDD e monterò il mio attuale
HDD meccanico nello spazio usato per il lettore cd(ho visto guide in internet).
Per quanto riguarda le ram, attualmente(1 di 2 slot occupati) è montata una DDR3 5GB Channel Single. (Nanya NT4GC64B8HB0NS-CG 4GB 2Rx8 SODIMM PC3-10600S-9-10-F2 DDR3) per intenderci.

Ora volevo fare un paio di domande.
1)Quanta Ram supporta questo notebook acer? (scheda madre VA50_HC_CR - Type2 - Board Version) Chiedo perchè ho trovato info discordanti su internet (qualcuno diceva 16/qualcuno diceva 32).
E a che frequenza massima posso prenderla?

2)Inoltre per quanto riguarda hard disk, trovate sia un modo efficiente per fare ciò? ed inoltre come posso migliore di più questa divisione che voglio fare?
Nel senso, nel nuovo ssd monterò comunque il dual boot(ci lavoro con windowz purtroppo) ma vorrei fare di tutto per poter ottimizzare il tutto.

In attesa delle vostre risposte, vi ringrazio in anticipo.

EDIT: aggiungo info

sudo hdparm -i /dev/sda

Codice: Seleziona tutto
    /dev/sda:

     Model=TOSHIBA MQ01ABD050, FwRev=AX003J, SerialNo=925IS3D3S
     Config={ Fixed }
     RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
     BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
     CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=976773168
     IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
     PIO modes:  pio0 pio1 pio2 pio3 pio4
     DMA modes:  sdma0 sdma1 sdma2 mdma0 mdma1 mdma2
     UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
     AdvancedPM=yes: unknown setting WriteCache=enabled
     Drive conforms to: Unspecified:  ATA/ATAPI-3,4,5,6,7

     * signifies the current active mode

sudo hdparm -I /dev/sda

Codice: Seleziona tutto
    /dev/sda:

    ATA device, with non-removable media
       Model Number:       TOSHIBA MQ01ABD050                     
       Serial Number:      925IS3D3S
       Firmware Revision:  AX003J 
       Transport:          Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
    Standards:
       Supported: 8 7 6 5
       Likely used: 8
    Configuration:
       Logical      max   current
       cylinders   16383   16383
       heads      16   16
       sectors/track   63   63
       --
       CHS current addressable sectors:    16514064
       LBA    user addressable sectors:   268435455
       LBA48  user addressable sectors:   976773168
       Logical  Sector size:                   512 bytes
       Physical Sector size:                  4096 bytes
       Logical Sector-0 offset:                  0 bytes
       device size with M = 1024*1024:      476940 MBytes
       device size with M = 1000*1000:      500107 MBytes (500 GB)
       cache/buffer size  = 8192 KBytes
       Form Factor: 2.5 inch
       Nominal Media Rotation Rate: 5400
    Capabilities:
       LBA, IORDY(can be disabled)
       Queue depth: 32
       Standby timer values: spec'd by Standard, no device specific minimum
       R/W multiple sector transfer: Max = 16   Current = 16
       Advanced power management level: 254
       DMA: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
            Cycle time: min=120ns recommended=120ns
       PIO: pio0 pio1 pio2 pio3 pio4
            Cycle time: no flow control=120ns  IORDY flow control=120ns
    Commands/features:
       Enabled   Supported:
          *   SMART feature set
              Security Mode feature set
          *   Power Management feature set
          *   Write cache
          *   Look-ahead
          *   Host Protected Area feature set
          *   WRITE_BUFFER command
          *   READ_BUFFER command
          *   NOP cmd
          *   DOWNLOAD_MICROCODE
          *   Advanced Power Management feature set
              SET_MAX security extension
          *   48-bit Address feature set
          *   Device Configuration Overlay feature set
          *   Mandatory FLUSH_CACHE
          *   FLUSH_CACHE_EXT
          *   SMART error logging
          *   SMART self-test
          *   General Purpose Logging feature set
          *   WRITE_{DMA|MULTIPLE}_FUA_EXT
          *   64-bit World wide name
          *   IDLE_IMMEDIATE with UNLOAD
          *   WRITE_UNCORRECTABLE_EXT command
          *   {READ,WRITE}_DMA_EXT_GPL commands
          *   Segmented DOWNLOAD_MICROCODE
          *   Gen1 signaling speed (1.5Gb/s)
          *   Gen2 signaling speed (3.0Gb/s)
          *   Gen3 signaling speed (6.0Gb/s)
          *   Native Command Queueing (NCQ)
          *   Host-initiated interface power management
          *   Phy event counters
          *   Idle-Unload when NCQ is active
          *   Host automatic Partial to Slumber transitions
          *   Device automatic Partial to Slumber transitions
          *   READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
          *   DMA Setup Auto-Activate optimization
          *   Device-initiated interface power management
          *   Software settings preservation
          *   SMART Command Transport (SCT) feature set
          *   SCT Write Same (AC2)
          *   SCT Error Recovery Control (AC3)
          *   SCT Features Control (AC4)
          *   SCT Data Tables (AC5)
    Security:
       Master password revision code = 65534
          supported
       not   enabled
       not   locked
          frozen
       not   expired: security count
          supported: enhanced erase
       116min for SECURITY ERASE UNIT. 116min for ENHANCED SECURITY ERASE UNIT.
    Logical Unit WWN Device Identifier: 5000039445e81b18
       NAA      : 5
       IEEE OUI   : 000039
       Unique ID   : 445e81b18
    Checksum: correct

inxi -Fz

Codice: Seleziona tutto
    inxi -Fz
    System:    Host: ************* Kernel: 4.18.0-18-generic x86_64 bits: 64 Desktop: Gnome 3.28.3
               Distro: Ubuntu 18.04.2 LTS
    Machine:   Device: laptop System: Acer product: Aspire V3-571G v: V2.07 serial: N/A
               Mobo: Acer model: VA50_HC_CR v: Type2 - Board Version serial: N/A
               UEFI [Legacy]: Acer v: V2.07 date: 10/15/2012
    Battery    BAT1: charge: 4.0 Wh 100.0% condition: 4.0/48.8 Wh (8%)
    CPU:       Quad core Intel Core i7-3632QM (-MT-MCP-) cache: 6144 KB
               clock speeds: max: 3200 MHz 1: 1201 MHz 2: 1206 MHz 3: 1202 MHz 4: 1211 MHz 5: 1199 MHz 6: 1209 MHz
               7: 1204 MHz 8: 1199 MHz
    Graphics:  Card-1: Intel 3rd Gen Core processor Graphics Controller
               Card-2: NVIDIA GF117M [GeForce 610M/710M/810M/820M / GT 620M/625M/630M/720M]
               Display Server: x11 (X.Org 1.20.1 ) drivers: modesetting,nvidia (unloaded: fbdev,vesa,nouveau)
               Resolution: [email protected], [email protected]
               OpenGL: renderer: GeForce 710M/PCIe/SSE2 version: 4.4.0 NVIDIA 340.107
    Audio:     Card Intel 7 Series/C216 Family High Definition Audio Controller driver: snd_hda_intel
               Sound: Advanced Linux Sound Architecture v: k4.18.0-18-generic
    Network:   Card-1: Broadcom and subsidiaries NetLink BCM57785 Gigabit Ethernet PCIe driver: tg3
               IF: enp2s0f0 state: up speed: 1000 Mbps duplex: full mac: <filter>
               Card-2: Qualcomm Atheros AR9462 Wireless Network Adapter driver: ath9k
               IF: wlp3s0 state: up mac: <filter>
    Drives:    HDD Total Size: 500.1GB (10.0% used)
               ID-1: /dev/sda model: TOSHIBA_MQ01ABD0 size: 500.1GB
    Partition: ID-1: / size: 179G used: 47G (28%) fs: ext4 dev: /dev/sda5
    RAID:      No RAID devices: /proc/mdstat, md_mod kernel module present
    Sensors:   System Temperatures: cpu: 58.0C mobo: N/A gpu: 55C
               Fan Speeds (in rpm): cpu: N/A
    Info:      Processes: 336 Uptime: 6 min Memory: 1814.2/3764.9MB Client: Shell (bash) inxi: 2.3.56

[FreeMan]

sezione errata

leggi le regole di sezione

cerca l'eventuale thread ufficiale dedicato al tuo portatile

CLOSED!!

>bYeZ<