Configurazione Cisco 1841 - Alice Casa - 7M

[crudican]

Buongiorno a tutti,
sono nuovo del forum e ho un problema che non riesco a risolvere ormai da un mese, ho configurato il router in oggetto e funziona tutto ma purtroppo la velocità è 0,60 in Download e 0,40 in Upload.

Mentre prima con il router Telecom andava a 3,00 in Download e 0,40 in Upload.

Ecco la configurazione del router:

version 12.4
service timestamps debug datetime msec
service timestamps log uptime
no service password-encryption
!
hostname AliceADSL
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$ibpw$hGHwG8ajHvZ4vKxBpmjty1
!
no aaa new-model
ip cef
!
!
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1
!
ip dhcp pool LOCAL
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 85.37.17.52 85.38.28.92
!
!
ip name-server 85.37.17.52
ip name-server 85.38.28.92
multilink bundle-name authenticated
!
!
!
!
archive
log config
hidekeys
!
!
!
!
!
interface FastEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
no ip mroute-cache
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface ATM0/0/0
mtu 1492
no ip address
no ip mroute-cache
no atm ilmi-keepalive
dsl operating-mode auto
hold-queue 224 in
pvc 8/35
encapsulation aal5snap
protocol ppp dialer
dialer pool-member 1
!
!
interface Dialer0
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp pap sent-username aliceadsl password 0 aliceadsl
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
!
!
no ip http server
no ip http secure-server
ip nat inside source list 101 interface Dialer0 overload
!
access-list 101 permit ip 192.168.1.0 0.0.0.255 any
dialer-list 1 protocol ip permit
!
!
!
control-plane
!
!
!
line con 0
line aux 0
line vty 0 4
login local
!
scheduler allocate 20000 1000
end

Ed ecco lo status dell'ATM

ATM0/0/0
Alcatel 20150 chipset information
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT) Annex A
ITU STD NUM: 0x01 0x1
Vendor ID: ' ' 'TSTC'
Vendor Specific: 0xDBB0 0x0000
Vendor Country: 0x04 0xB5
Capacity Used: 97% 73%
Noise Margin: 10.5 dB 21.0 dB
Output Power: 20.0 dBm 12.0 dBm
Attenuation: 20.5 dB 10.5 dB
Defect Status: None None
Last Fail Code: None
Watchdog Counter: 0xEC
Watchdog Resets: 0
Selftest Result: 0x00
Subfunction: 0x15
Interrupts: 2650 (0 spurious)
PHY Access Err: 0
Activations: 1
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: ASW_init_3_8_131.bin
Operation FW: ASW_R3_8_131.bin
FW Source: embedded
FW Version: 3.8.131

Interleave Fast Interleave Fast
Speed (kbps): 7456 0 480 0
Cells: 26132 0 249291 0
Reed-Solomon EC: 1649 0 0 0
CRC Errors: 0 0 0 0
Header Errors: 0 0 0 0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0

LOM Monitoring : Disabled


DMT Bits Per Bin
000: 0 0 0 0 0 0 0 3 3 4 6 7 7 8 7 9
010: 8 9 9 8 8 8 9 8 8 8 7 6 5 5 0 0
020: 0 0 0 0 0 0 7 7 8 8 9 A A B B B
030: B C C C C C C C C C C C C C C C
040: 0 C C C C C C C C C C C C C C C
050: C C C C C C C C C C C C 2 C C C
060: C C B B B B B B B B B B B B B B
070: B B B B B B B B B B B B B B B B
080: B B B B B B B B B B B B B B B A
090: B B A B A A A A A A A A A A A A
0A0: A A A A A A A A A A A A A A A A
0B0: A A A A A A A A A A A A A A A 9
0C0: A A A A A 9 9 9 9 9 9 9 9 9 9 9
0D0: 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9
0E0: 9 9 9 9 9 9 9 9 9 9 9 8 8 8 7 6
0F0: 5 4 4 5 4 0 0 0 0 0 0 0 0 0 0 0

DSL: Training log buffer capability is not enabled

Grazie Mille

Spero possiate aiutarmi sono disperato.