|
|
|
![]() |
|
Strumenti |
![]() |
#1 |
Senior Member
Iscritto dal: Dec 2006
Messaggi: 9542
|
[Thread ufficiale] Collegamento/uso di 2 router in cascata
Ho deciso di pubblicare questa guida in quanto nell'ultimo periodo vedo tante richieste su come collegare 2 router in cascata, esempio: un router con modem adsl integrato collegato ad un router senza modem integrato(con porta WAN)
Guida Consigliata per connessioni ADSL PPPoE(Telecom,WIND,ecc) Guida Alternativa per connessioni ADSL PPPoA(Tiscali) Guida per Router ADSL e Router Broadband con LAN separate Guida per trasformare un router in semplice Switch-Access Point English guide is below(second post) Guida valida per tutte le ADSL di tipo PPP, non vale quindi per abbonamenti con IP Statici(Telecom Business, ecc) Gli utenti Fastweb ADSL potrebbe provare la guida in bridge mode(guida consigliata) mettendo però VCI=36 Chi possiede un router ADSL fornito dal proprio ISP per servizi aggiuntivi quali VoIP\IPTV, deve necessariamente collegare tale router alla presa telefonica. Non è possibile utilizzare la guida "consigliata" in questo caso, non funzionerbbe più l'IPTV\VoIP. Consiglio di prendere un Access Point Puro per chi deve portare la connettività internet dal router principale in altri punti della casa\ufficio(basta settare l'AP in modalità repeater, oppure WDS... primo router permettendo per discorso compatibilità) [/b] Attenzione(Come trasformare un router in Switch-Access Point): chi è in possesso di 2 router entrambi ADSL può utillzzare il 2° router come semplice switch\Access Point, basta disabilitare il DHCP al 2° router, infine i due router devono essere collegati tramite cavo ETH da porta LAN a porta LAN. Lo stesso vale qualora il 2° router avesse la porta WAN(anche se consiglio le guide sottostanti). Per gestire entrambi gli apparati via webinterface conviene cambiare l'IP di uno dei due router(es. 1° router 192.168.1.1/255.255.255.0 e secondo router 192.168.1.50/255.255.255.0) Il mio consiglio è sempre lo stesso(Guida consigliata): 1) trasformare il router con modem integrato in modem puro 2) settare i parametri di certificazione dell'ISP nella sezione PPPoE del router(quello con porta WAN, senza modem integrato) 3) collegare il cavo ETH dalla porta LAN del modem puro alla porta WAN del router senza modem integrato Requisiti per la realizzazione di questa configurazione: 1) configurazione in PPPoE lato ISP(se il vostro ISP non supporta il PPPoE vedi la guida alternativa in fondo) 2) modem adsl ETH oppure router ETH con modem adsl integrato 3) cavo ETH 4) router ETH senza modem adsl integrato Ecco un esempio utilizzando 2 prodotto D-Link(DSL-604T e DI-624T) Il principio non cambia per altri modelli, per questo motivo non entro in particolari tipo l'indirizzo IP dei prodotti e come salvare le relative configurazioni Prima di iniziare è preferibile un reset alle impostazioni di fabbrica dei vari prodotti a disposizione Primo step: Trasformare il router con modem in MODEM PURO: Grazie al protocollo RFC 1483 Bridged IP LLC(Vpi=8 e Vci=35) è sempre possibile trasformare un router ETH in modem ETH PURO Questa configurazione rende trasparente il router, quindi disabilita NAT, DHCP e Firewall Integrato. Nella sezione WAN del modem\router adsl selezioniamo il bridge mode(in alcuni modelli troviamo la voce "Pure Bridge Mode") ![]() Per rientrare nella configurazione di tale prodotto dopo averlo spento oppure dopo aver spento il PC, è necessario forzare il TCP/IP in quanto il DHCP non entra più in gioco Secondo Step: Configurazione client certificazione lato router con porta WAN Anche qui nella sezione WAN cerchiamo la voce PPPoE e mettiamo semplicemente username e password del nostro provider ![]() Terzo Step: Collegare i due prodotti insieme L'ultima fase è di collegare il modem puro alla porta WAN del secondo router ![]() L'eventuale portforwarding si effettua logicamente sul router senza modem integrato Un grazie particolare a pegasolabs! Guida Alternativa per gli ISP che lavorano SOLO in PPPoATM: Requisiti per la realizzazione di questa configurazione: 1) modem adsl ETH oppure router ETH con modem adsl integrato con funzione HALF-BRIDGE MODE 2) cavo ETH 3) router ETH senza modem adsl integrato 4)E' obbligatorio che i 2 router siano in due subnet diverse(es. 1° router 192.168.1.1/255.255.255.0 e secondo router 192.168.0.1/255.255.255.0). Con questa configurazione sarà sempre possibile gestire entrambi gli apparati da un PC dietro il router WAN. Inoltre, è obbligatorio che le subnet siano diverse perchè la porta WAN non può avere un IP appartente alla stessa subnet del suo DHCP Server(es. se la subnet del DHCP Server del router WAN è 192.168.0.0/24 non è possibile assegnare un IP della subnet 192.168.0.0/24 alla porta WAN, 2 interfacce di Livello 3 non posso appartenere alla stessa subnet) le screenshot sottostanti sono del routerino Trust 4050 con firmware Billion e router WAN TP-Link Parte 1: Modem ADSL Partiamo con il prodotto con modem ADSL 1) iniziamo con un reset factory settings 2) settiamo la parte WAN in PPPoA VC-MUX VPI=8 e VCI=35 NAT disable e Half Bridge Mode enabled vedi screen: ![]() ![]() Parentesi: collegando un PC direttamente al modem in half bridge mode dovreste avere un ipconfig /all che assomigli a questo: ![]() 3) consiglio anche di disabilitare l'eventuale firewall: ![]() Parte 2: Router WAN Lato router WAN basta selezionare nella WAN Dynamic IP Address cioè di ottenere l'IP automaticamente ![]() Infine basta collegare il modem adsl tramite cavo ETH alla porta WAN del 2° router In caso di problemi provate un riavvio sia del modem che il router Lo status del router WAN dovrebbe somigliare a questa screen: ![]() Il portfowarding per il P2P e simili si effettua sul router con porta WAN Nel caso incontraste problemi di navigazione(è capitato al sottoscritto durante i test collegando il PC direttamente al modem in half-bridge), potrebbe essere un problema di DNS. Quindi si può provare ad aggiungerli sul TCP/IP della scheda ETH oppure direttamente nella WAN del router senza modem Un grazie particolare al tecnico di fiducia Harry_Bosch ![]() Il contenuto di questo post è rilasciato con licenza Creative Commons Attribution-Noncommercial-Share Alike 2.5
__________________
Harry Callahan: We're not just going to let you walk out of here. Crook: Who's "we", sucker? Harry Callahan: Smith, and Wesson, and me. Ultima modifica di Harry_Callahan : 20-10-2010 alle 22:09. |
![]() |
![]() |
![]() |
#2 |
Senior Member
Iscritto dal: Dec 2006
Messaggi: 9542
|
English Guide
How to connect 2 routers together using an ADSL PPP connection(1 router with ADSL modem and the other without integrated modem(broadband router), this guide is not for Static IP ADSLs)
If you have a ADSL router from your ISP and have a VoIP\IPTV service, you must connect this router to the telephone outlet. If you put the router in bridge mode you will lose the VoIP\IPTV connection. It's better to use an Access Point(without WAN port) to expand ETH or wireless connectivity(for wireless try using WDS mode) The most important thing when hooking up 2 routers is avoiding a double NAT configuration If both routers have an ADSL modem, you can use the second router as an Access Point\switch ETH. The only thing to do is disable the DHCP server of the second router and hook the two routers togther with an ETH cable. You can do the same if the second router has a WAN port, but I suggest the following guides for that! I suggest to change one of the routers webinterface IP, that way you can enter both routers from the same LAN(example: first router 192.168.1.1/255.255.255.0 & second router 192.168.1.50/255.255.255.0 The best way of getting rid of 1 NAT is this: 1) make the router with modem to act as a simple ADSL modem(no NAT-Firewall-DHCP Server) 2) set the ISP account in the PPPoE menù of the broadband router(router with WAN port, router without ADSL modem) 3) connect the routers together with an ETH cable. The cable must be inserted in the WAN port of the broadband router Specifications & Requirements: 1) your ISP must support PPPoE connections(if your ISP uses only PPPoATM see the PPPoATM guide below) 2) ETH adsl modem or router ETH with integrated adsl modem 3) ETH cable 4) router ETH without adsl modem(WAN port broadband router) I'm going to show an example with 2 D-Link products(DSL-604T & DI-624T) Other brands of routers can be used with the same configuration Let's start with a factory reset of the 2 routers First step: Putting the ADSL router in MODEM MODE ONLY: With the protocol RFC 1483 Bridged IP LLC(Vpi=8 e Vci=35) it is always possibile to switch off routing of an ADSL router This configuration disables NAT, DHCP & Firewall. In the WAN menù of the modem\router adsl we have to select bridge mode(or "Pure Bridge Mode" depending on the model) ![]() If for some reason you have to enter the webinterface of the modem-router(after using this guide), you must insert a static IP in TCP/IP of the computer because the bridge mode turns off DHCP server. Or you can also reset to router with reset button Second Step: PPPoE client configuration on the WAN router Find the WAN setup and simply insert your ISP username & password ![]() Third Step: Connecting the routers together The last step is to connection the routers togehter with an ETH cable, from LAN port of the ADSL modem to the WAN port of the broadband router ![]() Portforwarding is done only on the broadband router(the one with the WAN port) Guide for ISPs that support only PPPoATM connections: Specifications & Requirements: 1) ETH adsl modem or router ETH with modem adsl that has HALF-BRIDGE MODE function 2) ETH cable 3) router ETH without integrated adsl modem(broadband router that has a WAN port) 4) I suggest that the 2 routers have different IP addresses(first router 192.168.1.1/255.255.255.0 and second router 192.168.0.50/255.255.255.0) Screenshots below are from a Trust 4050 with Billion firmware and a WAN TP-Link router Part 1: ADSL Modem Lets start with the modem ADSL 1) do a reset factory settings 2) setup the WAN section in PPPoA VC-MUX VPI=8 e VCI=35 NAT disable e Half Bridge Mode enabled screenshots: ![]() ![]() a PC connected to the modem in half bridge mode should have a ipconfig /all like this: ![]() 3) manually switch off the firewall: ![]() Part 2: Router WAN On the broadband router the only thing we must do is select Dynamic IP Address (obtain IP automatically) ![]() Now connect the routers together from the LAN port of the adsl modem to the WAN port of the 2° router If you have any problems just try to restart both the routers(power off and the turn them on after a minute) The WAN Status of the broadband router should look like this: ![]() Portfowarding for P2P or other software must be done on the broadband router If the broadband router has a public IP and your having browsing problems, it could be a DNS problem Try putting your ISP DNSs on the TCP/IP of your PC or on the WAN section of the broadband router Il contenuto di questo post è rilasciato con licenza Creative Commons Attribution-Noncommercial-Share Alike 2.5
__________________
Harry Callahan: We're not just going to let you walk out of here. Crook: Who's "we", sucker? Harry Callahan: Smith, and Wesson, and me. Ultima modifica di Harry_Callahan : 19-09-2010 alle 20:27. |
![]() |
![]() |
![]() |
#3 | |
Senior Member
Iscritto dal: Dec 2006
Messaggi: 9542
|
Router ADSL + Router WAN(LAN Separate)
Guida per collegare un router ADSL con un router Broadband e bloccare la comunicazione tra i PC dietro il router WAN e quelli dietro il router ADSL
Di solito i PC collegati dietro un router Broadband raggiungono senza problemi quelli attaccati al router ADSL a monte(da quello ADSL verso WAN il traffico di solito è bloccato), con la seguente configurazione possiamo bloccare il traffico dalla LAN del router Broadband a quello ADSL Configurazione: Quote:
Gateway 192.168.1.1/255.255.255.0 ![]() DHCP sul Gateway a partire da 192.168.1.4 ![]() FRITZ! 7170 trasformato in router WAN(la porta LAN1 diventa la WAN) IP WAN 192.168.1.2/255.255.255.252 ![]() ![]() Extra: Per fare comunicare i PC dietro il router WAN con quelli dietro il router ADSL bisogna semplicemente utilizzare la subnet 255.255.255.0 sulla porta WAN(es. 192.168.1.2/255.255.255.0) oppure impostare la porta WAN in DHCP in modo che l'IP della porta WAN venga configurata dal DHCP Server del router ADSL Un ringraziamento particolare a nuovoUtente86 per i settaggi in questione Il contenuto di questo post è rilasciato con licenza Creative Commons Attribution-Noncommercial-Share Alike 2.5
__________________
Harry Callahan: We're not just going to let you walk out of here. Crook: Who's "we", sucker? Harry Callahan: Smith, and Wesson, and me. Ultima modifica di Harry_Callahan : 20-09-2010 alle 19:13. |
|
![]() |
![]() |
![]() |
#4 |
Senior Member
Iscritto dal: Feb 2007
Messaggi: 7120
|
Semplice, chiara,e utile
![]() Ciao Harry
__________________
|
![]() |
![]() |
![]() |
#5 |
Senior Member
Iscritto dal: Dec 2006
Messaggi: 9542
|
Grazie!
quando ti capita rimandali qui gli utenti Ciao Intrepido
__________________
Harry Callahan: We're not just going to let you walk out of here. Crook: Who's "we", sucker? Harry Callahan: Smith, and Wesson, and me. Ultima modifica di Harry_Callahan : 06-10-2007 alle 09:44. |
![]() |
![]() |
![]() |
#6 |
Senior Member
Iscritto dal: Dec 2003
Città: Caltanissetta
Messaggi: 16270
|
in effetti ci mancava una guida del genere
ogni volta bisognava ripetere tutti i passaggi per il bridge grazie Harry!!!! P.S.: Hai utilizzato router che detesto però..... ![]() |
![]() |
![]() |
![]() |
#7 |
Junior Member
Iscritto dal: Oct 2007
Messaggi: 16
|
please help
Ciao a tutti, mi sono appena registrato ed ho un problema.
Ho recentemente acquistato un router wireless della d-link (per collegarmi col portatile ad internet da tutti i punti della casa), modello di-524 (4 porte ethernet e una porta WAN per collegare il modem). Il problema è che avvio il wizard del router e faccio questi passi : 1) attacco l'alimentazione al router 2) attacco il router al pc home 3) attacco il modem al router successivamente configuro la connessione (tipo PPPoE, pass:aliceadsl e user:aliceadsl), quando il wizard testa se c'è internet attivo, mi da errore e mi dice di controllare la configurazione del modem . E' come se il router non vedesse il modem, in quanto il led del modem, che dovrebbe accendersi quando è collegato via ethernet, non da segni di vita. Qualcuno può aiutarmi? sto leggermente impazzendo. P.S. il cavo eth che collega il modem al router non è cross vero?? |
![]() |
![]() |
![]() |
#8 | |
Senior Member
Iscritto dal: Dec 2006
Messaggi: 9542
|
Quote:
segui la guida sopra attaccando un solo prodotto alla volta al PC terminata la configurazione del singolo prodotto, basta attaccare i prodotti insieme
__________________
Harry Callahan: We're not just going to let you walk out of here. Crook: Who's "we", sucker? Harry Callahan: Smith, and Wesson, and me. |
|
![]() |
![]() |
![]() |
#9 |
Senior Member
Iscritto dal: May 2004
Città: Salerno
Messaggi: 21185
|
Il primo "modem" l'hai messo in bridge come indicato nella guida?
![]() |
![]() |
![]() |
![]() |
#10 | |
Junior Member
Iscritto dal: Oct 2007
Messaggi: 16
|
Quote:
Collegamento PC Stato Indirizzo IP Indirizzo MAC Collegamento Ethernet Attivo 192.168.1.3 00:E0:4C:B0:18:7D Collegamento USB Non attivo nothing nothing Linea ADSL Stato linea ADSL Attivo Velocità down link (kbps) 2464 Velocità up link (kbps) 352 Modalità ADSL G.DMT VPI/VCI 8/35 Protocollo-Incapsulamento Bridge LLC/SNAP Identificativi Prodotto Nome e ID Alice ADSL 302T Versione Software V1.00B01T16.TI.20040224 Versione Firmware ADSL 4.02.01.00 - 3.00.02.01 - 1.01.00.00 Annex A - 01.06.06 - 0.49 |
|
![]() |
![]() |
![]() |
#11 |
Senior Member
Iscritto dal: Dec 2006
Messaggi: 9542
|
e l'hai attaccato alla porta WAN, giusto?
__________________
Harry Callahan: We're not just going to let you walk out of here. Crook: Who's "we", sucker? Harry Callahan: Smith, and Wesson, and me. |
![]() |
![]() |
![]() |
#12 |
Junior Member
Iscritto dal: Oct 2007
Messaggi: 16
|
alla porta WAN del router wireless, si... ma cm dicevo prima il led del modem nn si accede.. (ho provato a collegarlo sia col cavo cross e sia col cavo normale). Il bello è k ho appena provato a collegare il modem non nella porta WAN, ma in una porta normale del router e mi si è accesa la luce del modem....
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#13 |
Senior Member
Iscritto dal: Dec 2006
Messaggi: 9542
|
riesci a navigare? E' strano perchè con la porta WAN dovrebbe connettersi
__________________
Harry Callahan: We're not just going to let you walk out of here. Crook: Who's "we", sucker? Harry Callahan: Smith, and Wesson, and me. |
![]() |
![]() |
![]() |
#14 | |
Junior Member
Iscritto dal: Oct 2007
Messaggi: 16
|
Quote:
nn si connette con la porta WAN.... mentre se lo attacco ad un'altra porta navigo solo con questo pc via ethernet e non col portatile via wireless, xò mi chiede la connessione del modem sul pc connesso via ethernet.. mah... misteri... |
|
![]() |
![]() |
![]() |
#15 | |
Senior Member
Iscritto dal: Dec 2006
Messaggi: 9542
|
Quote:
molto probabilmente di defualt è impostato su connect on demand, come in questo screen: ![]() riprova con il PPPoE, porta WAN e sposta su "Always ON" facci sapere
__________________
Harry Callahan: We're not just going to let you walk out of here. Crook: Who's "we", sucker? Harry Callahan: Smith, and Wesson, and me. |
|
![]() |
![]() |
![]() |
#16 |
Senior Member
Iscritto dal: Dec 2003
Città: Caltanissetta
Messaggi: 16270
|
forse ha incasinato qualcosa con pppoe e simili
sarebbe opportuno eventualmente eseguire un reset del dispositivo |
![]() |
![]() |
![]() |
#17 |
Junior Member
Iscritto dal: Oct 2007
Messaggi: 16
|
|
![]() |
![]() |
![]() |
#18 | |
Senior Member
Iscritto dal: Dec 2003
Città: Caltanissetta
Messaggi: 16270
|
Quote:
la cosa che mi stranizza è che dici che il tuo modem ha un indirizzo ip del tipo 192.168.1.3 se settato in bridge non ne dovrebbe avere in quanto gli verrà assegnato direttamente un indirizzo ip pubblico dall'ISP ad avvenuta connessione |
|
![]() |
![]() |
![]() |
#19 | |
Senior Member
Iscritto dal: Dec 2006
Messaggi: 9542
|
Quote:
perchè a questo punto potrebbe essere anche un difetto della porta WAN
__________________
Harry Callahan: We're not just going to let you walk out of here. Crook: Who's "we", sucker? Harry Callahan: Smith, and Wesson, and me. |
|
![]() |
![]() |
![]() |
#20 | |
Junior Member
Iscritto dal: Oct 2007
Messaggi: 16
|
Quote:
e kmq penso di avere il firmware bloccato visto k non mi fa cambiare niente sulle impostazioni del modem. ![]() |
|
![]() |
![]() |
![]() |
Strumenti | |
|
|
Tutti gli orari sono GMT +1. Ora sono le: 19:03.