Ubuntu non masterizza

[fsdfdsddijsdfsdfo]

O meglio: masterizza male.

Stavo scrivendo un immagine di Xubuntu per un amico... ironia della sorte non vuole masterizzare... Crea il cd ma dentro ci sono solo quattro schifezze... abbastanza per bruciarlo...

Posto il log:

valeria@ubuntu:~$ sudo gnomebaker
Password:

(process:5565): GStreamer-WARNING **: The GStreamer function gst_init_get_option_group() was
called, but the GLib threading system has not been initialised
yet, something that must happen before any other GLib function
is called. The application needs to be fixed so that it calls
if (!g_thread_supported ()) g_thread_init(NULL);
as very first thing in its main() function. Please file a bug
against this application.
libnotify-Message: Unable to get session bus: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken.

** (gnomebaker:5565): CRITICAL **: dbus_g_proxy_connect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed

** (gnomebaker:5565): CRITICAL **: dbus_g_proxy_connect_signal: assertion `DBUS_IS_G_PROXY (proxy)' failed

** (gnomebaker:5565): CRITICAL **: dbus_g_proxy_call: assertion `DBUS_IS_G_PROXY (proxy)' failed

** (gnomebaker:5565): CRITICAL **: dbus_g_proxy_call: assertion `DBUS_IS_G_PROXY (proxy)' failed
valeria@ubuntu:~$

wodim: No write mode specified.
wodim: Asuming -tao mode.
wodim: Future versions of wodim may have different drive dependent defaults.
scsidev: '4,0,0'
scsibus: 4 target: 0 lun: 0
Linux sg driver version: 3.5.34
Wodim version: 1.1.2
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 3 = CD-ROM XA mode 2
atapi: 1
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'HL-DT-ST'
Identification : 'DVDRAM GSA-T10N '
Revision : 'PC05'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009 (CD-R)
Profile: 0x0012 (DVD-RAM)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0015 (DVD-R/DL sequential recording)
Profile: 0x0016 (DVD-R/DL layer jump recording)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x001A (DVD+RW)
Profile: 0x001B (DVD+R)
Profile: 0x002B (DVD+R/DL)
Profile: 0x0010 (DVD-ROM)
Profile: 0x0009 (CD-R) (current)
Profile: 0x000A (CD-RW)
Profile: 0x0008 (CD-ROM)
Profile: 0x0002 (Removable disk)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1053696 = 1029 KB
Drive DMA Speed: 9242 kB/s 52x CD 6x DVD
FIFO size : 12582912 = 12288 KB
Speed set to 1764 KB/s
 4 seconds. 3 seconds. 2 seconds. 1 seconds. 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Starting new track at sector: 0
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB: 2A 00 00 00 00 9B 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 10 2A 30 02 80 21 02 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x21 Qual 0x02 (invalid address for write) Fru 0x0
Sense flags: Blk 0 (not valid)
resid: 63488
cmd finished after 0.002s timeout 40s
wodim: The current problem looks like a buffer underrun.
wodim: It looks like 'driveropts=burnfree' does not work for this drive.
wodim: Please report.
wodim: Make sure that you are root, enable DMA and check your HW/OS set up.

write track data: error after 317440 bytes
Writing time: 20.021s
Average write speed 193.2x.
Fixating...
Fixating time: 28.185s

[barraacodice]

Perchè hai lanciato gnomebaker con sudo?
C'è un qualche problema con GStreamer. Prova un pò con k3b...

[fsdfdsddijsdfsdfo]

Originariamente inviato da barraacodice

Perchè hai lanciato gnomebaker con sudo?
C'è un qualche problema con GStreamer. Prova un pò con k3b...

perchè sennò ad un certo punto nel log mi consigliava di SUDOare... scusate se non lo posto ma non voglio bruciare un altro cd

[barraacodice]

E' molto strano, qualcosa non va di sicuro, gnomebaker deve poter essere usato da utente normale
Installa K3B e togliti il pensiero. Anche se hai gnome non c'è nessun problema di conflitti o altro. Inoltre ha più funzioni di gnomebaker