Info sul connettore posteriore. E' il connettore della console seriale (finalmente!)
I pin sono (da sinistra a destra / dall'alto verso il basso)
GND GND GND
RX VCC TX
Attacando un cavo seriale (vedi link x costruzione cavo console seriale) al boot del modem compare
----------------------------------------------------------- Bootlog
CFE version 1.0.37-10.2 for BCM96348 (32bit,SP,BE)
Build Date: Wed Jul 2 19:25:25 CST 2008 (root@localhost.localdomain)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AB, id 0x22a8, size 4096KB
Unknown PHY type
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)
Total memory used by CFE: 0x80401000 - 0x80525140 (1196352)
Initialized Data: 0x8041C8D0 - 0x8041E890 (8128)
BSS Area: 0x8041E890 - 0x80423140 (18608)
Local Heap: 0x80423140 - 0x80523140 (1048576)
Stack Area: 0x80523140 - 0x80525140 (8192)
Text (code) segment: 0x80401000 - 0x8041C8C4 (112836)
Boot area (physical): 0x00526000 - 0x00566000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 3
Board Id (0-9) : D-4P-W
Number of MAC Addresses (1-32) : 24
Base MAC Address : xx:xx:xx:xx:xx:xx
PSI Size (1-128) KBytes : 48
Dying Gasp Enable (0
isable 1:Enable) : 1
*** Press any key to stop auto run (3 seconds) ***
Auto run second count down: 0
Booting from only image (0xbfc10000) ...
Code Address: 0x80010000, Entry Address: 0x801b1018
Decompression OK!
Entry at 0x801b1018
Closing network.
Starting program at 0x801b1018
Linux version 2.6.8.1 (root@localhost.localdomain) (gcc version 3.4.2) #1 Wed Jul 2 19:28:36 CST 200
8
Parallel flash device: name MX29LV320AB, id 0x22a8, size 4096KB
D-4P-W prom init
CPU revision is: 00029107
Determined physical RAM map:
memory: 00fa0000 @ 00000000 (usable)
On node 0 totalpages: 4000
DMA zone: 4000 pages, LIFO batch:1
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
PID hash table entries: 64 (order 6: 512 bytes)
Using 128.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 13912k/16000k available (1452k kernel code, 2068k reserved, 212k data, 72k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80e00000 ... 0x80f00000>
Calibrating delay loop... 255.59 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction... unavailable.
NET: Registered protocol family 16
Total Flash size: 4096K with 71 sectors
File system address: 0xbfc10100
Can't analyze prologue code at 80179904
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
brcmboard: brcm_board_init entry
Invalid External Interrupt definition
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
URL Filter v1.1 initialized
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 72k freed
init started: BusyBox v1.00 (2008.07.02-11:33+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
mount: Mounting none on /proc/bus/usb failed: No such file or direc
BusyBox v1.00 (2008.07.02-11:33+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6348B0 Ethernet Network Device v0.3 Jul 2 2008 19:27:18
Config Ethernet Switch Through SPI Slave Select 0
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
eth0: MAC Address: xx:xx:xx:xx:xx:xx
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: xx:xx:xx:xx:xx:xx
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.5.cpe2.0
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
BcmAdsl_Initialize=0xC00603C8, g_pFnNotifyCallback=0xC00798D4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA0FFFFF8, 0x1810 0x868822E0
AdslCoreHwReset: AdslOemDataAddr = 0xA0FFD4D4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!
==> Bcm963xx Software Version: EU_3-10-02-2900.A2pB022g2.d20h.dlinkdle_euDSL-2640B <==
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
Setting SSID "dlink"
Setting country code using abbreviation: "GB"
wlctl: Not Found
wlctl: Not Found
wlctl: Not Found
channel 1 selected
device wl0 entered promiscuous mode
br0: port 2(wl0) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0) entering forwarding state
sntp: host not found
Done
swapn task PID 494 for PC App
Fermando il boot appena acceso il modem invece
-------------------------------------------------------------------- Stop boot
CFE version 1.0.37-10.2 for BCM96348 (32bit,SP,BE)
Build Date: Wed Jul 2 19:25:25 CST 2008 (root@localhost.localdomain)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AB, id 0x22a8, size 4096KB
Unknown PHY type
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
Total memory: 16777216 bytes (16MB)
Total memory used by CFE: 0x80401000 - 0x80525140 (1196352)
Initialized Data: 0x8041C8D0 - 0x8041E890 (8128)
BSS Area: 0x8041E890 - 0x80423140 (18608)
Local Heap: 0x80423140 - 0x80523140 (1048576)
Stack Area: 0x80523140 - 0x80525140 (8192)
Text (code) segment: 0x80401000 - 0x8041C8C4 (112836)
Boot area (physical): 0x00526000 - 0x00566000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 3
Board Id (0-9) : D-4P-W
Number of MAC Addresses (1-32) : 24
Base MAC Address : xx:xx:xx:xx:xx:xx
PSI Size (1-128) KBytes : 48
Dying Gasp Enable (0
isable 1:Enable) : 1
*** Press any key to stop auto run (3 seconds) ***
Auto run second count down: 3
web info: Waiting for connection on socket 0.
CFE>
CFE> help
Available commands:
w Write the whole image start from beginning of the flash
e Erase [n]vram or [a]ll flash except bootrom
r Run program from flash image or from host depend on [f/h] flag
p Print boot line and board parameter info
c Change booline parameters
f Write image to the flash
i Erase persistent storage data
b Change board parameters
reset Reset the board
flashimage Flashes a compressed image after the bootloader.
help Obtain help for CFE commands
For more information about a command, enter 'help command-name'
*** command status = 0