unascarpa
03-05-2019, 11:36
Salve a tutti,
oramai devo prendere un pc nuovo, ma volevo anche per non sprecare un pc, potenziare il mio attuale.
Quindi diciamo che avevo pensato di spendere un 100 euro per upgradare questo harware.
innanzitutto ho un Intel Core i7 3632QM, attualemente con un HDD da 500Gb e monto Ubuntu 18.04 in dual boot con windowz.
Per quanto riguarda il disco rigido, passerò ad un ssd montato al posto del HDD e monterò il mio attuale
HDD meccanico nello spazio usato per il lettore cd(ho visto guide in internet).
Per quanto riguarda le ram, attualmente(1 di 2 slot occupati) è montata una DDR3 5GB Channel Single. (Nanya NT4GC64B8HB0NS-CG 4GB 2Rx8 SODIMM PC3-10600S-9-10-F2 DDR3) per intenderci.
Ora volevo fare un paio di domande.
1)Quanta Ram supporta questo notebook acer? (scheda madre VA50_HC_CR - Type2 - Board Version) Chiedo perchè ho trovato info discordanti su internet (qualcuno diceva 16/qualcuno diceva 32).
E a che frequenza massima posso prenderla?
2)Inoltre per quanto riguarda hard disk, trovate sia un modo efficiente per fare ciò? ed inoltre come posso migliore di più questa divisione che voglio fare?
Nel senso, nel nuovo ssd monterò comunque il dual boot(ci lavoro con windowz purtroppo) ma vorrei fare di tutto per poter ottimizzare il tutto.
In attesa delle vostre risposte, vi ringrazio in anticipo.
EDIT: aggiungo info
sudo hdparm -i /dev/sda
Codice: Seleziona tutto
/dev/sda:
Model=TOSHIBA MQ01ABD050, FwRev=AX003J, SerialNo=925IS3D3S
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=976773168
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive conforms to: Unspecified: ATA/ATAPI-3,4,5,6,7
* signifies the current active mode
sudo hdparm -I /dev/sda
Codice: Seleziona tutto
/dev/sda:
ATA device, with non-removable media
Model Number: TOSHIBA MQ01ABD050
Serial Number: 925IS3D3S
Firmware Revision: AX003J
Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
Supported: 8 7 6 5
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 976773168
Logical Sector size: 512 bytes
Physical Sector size: 4096 bytes
Logical Sector-0 offset: 0 bytes
device size with M = 1024*1024: 476940 MBytes
device size with M = 1000*1000: 500107 MBytes (500 GB)
cache/buffer size = 8192 KBytes
Form Factor: 2.5 inch
Nominal Media Rotation Rate: 5400
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: 254
DMA: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
SET_MAX security extension
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* IDLE_IMMEDIATE with UNLOAD
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Segmented DOWNLOAD_MICROCODE
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Gen3 signaling speed (6.0Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
* Idle-Unload when NCQ is active
* Host automatic Partial to Slumber transitions
* Device automatic Partial to Slumber transitions
* READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
* DMA Setup Auto-Activate optimization
* Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Write Same (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
supported: enhanced erase
116min for SECURITY ERASE UNIT. 116min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 5000039445e81b18
NAA : 5
IEEE OUI : 000039
Unique ID : 445e81b18
Checksum: correct
inxi -Fz
Codice: Seleziona tutto
inxi -Fz
System: Host: ************* Kernel: 4.18.0-18-generic x86_64 bits: 64 Desktop: Gnome 3.28.3
Distro: Ubuntu 18.04.2 LTS
Machine: Device: laptop System: Acer product: Aspire V3-571G v: V2.07 serial: N/A
Mobo: Acer model: VA50_HC_CR v: Type2 - Board Version serial: N/A
UEFI [Legacy]: Acer v: V2.07 date: 10/15/2012
Battery BAT1: charge: 4.0 Wh 100.0% condition: 4.0/48.8 Wh (8%)
CPU: Quad core Intel Core i7-3632QM (-MT-MCP-) cache: 6144 KB
clock speeds: max: 3200 MHz 1: 1201 MHz 2: 1206 MHz 3: 1202 MHz 4: 1211 MHz 5: 1199 MHz 6: 1209 MHz
7: 1204 MHz 8: 1199 MHz
Graphics: Card-1: Intel 3rd Gen Core processor Graphics Controller
Card-2: NVIDIA GF117M [GeForce 610M/710M/810M/820M / GT 620M/625M/630M/720M]
Display Server: x11 (X.Org 1.20.1 ) drivers: modesetting,nvidia (unloaded: fbdev,vesa,nouveau)
Resolution: 1366x768@60.01hz, 1680x1050@59.95hz
OpenGL: renderer: GeForce 710M/PCIe/SSE2 version: 4.4.0 NVIDIA 340.107
Audio: Card Intel 7 Series/C216 Family High Definition Audio Controller driver: snd_hda_intel
Sound: Advanced Linux Sound Architecture v: k4.18.0-18-generic
Network: Card-1: Broadcom and subsidiaries NetLink BCM57785 Gigabit Ethernet PCIe driver: tg3
IF: enp2s0f0 state: up speed: 1000 Mbps duplex: full mac: <filter>
Card-2: Qualcomm Atheros AR9462 Wireless Network Adapter driver: ath9k
IF: wlp3s0 state: up mac: <filter>
Drives: HDD Total Size: 500.1GB (10.0% used)
ID-1: /dev/sda model: TOSHIBA_MQ01ABD0 size: 500.1GB
Partition: ID-1: / size: 179G used: 47G (28%) fs: ext4 dev: /dev/sda5
RAID: No RAID devices: /proc/mdstat, md_mod kernel module present
Sensors: System Temperatures: cpu: 58.0C mobo: N/A gpu: 55C
Fan Speeds (in rpm): cpu: N/A
Info: Processes: 336 Uptime: 6 min Memory: 1814.2/3764.9MB Client: Shell (bash) inxi: 2.3.56
oramai devo prendere un pc nuovo, ma volevo anche per non sprecare un pc, potenziare il mio attuale.
Quindi diciamo che avevo pensato di spendere un 100 euro per upgradare questo harware.
innanzitutto ho un Intel Core i7 3632QM, attualemente con un HDD da 500Gb e monto Ubuntu 18.04 in dual boot con windowz.
Per quanto riguarda il disco rigido, passerò ad un ssd montato al posto del HDD e monterò il mio attuale
HDD meccanico nello spazio usato per il lettore cd(ho visto guide in internet).
Per quanto riguarda le ram, attualmente(1 di 2 slot occupati) è montata una DDR3 5GB Channel Single. (Nanya NT4GC64B8HB0NS-CG 4GB 2Rx8 SODIMM PC3-10600S-9-10-F2 DDR3) per intenderci.
Ora volevo fare un paio di domande.
1)Quanta Ram supporta questo notebook acer? (scheda madre VA50_HC_CR - Type2 - Board Version) Chiedo perchè ho trovato info discordanti su internet (qualcuno diceva 16/qualcuno diceva 32).
E a che frequenza massima posso prenderla?
2)Inoltre per quanto riguarda hard disk, trovate sia un modo efficiente per fare ciò? ed inoltre come posso migliore di più questa divisione che voglio fare?
Nel senso, nel nuovo ssd monterò comunque il dual boot(ci lavoro con windowz purtroppo) ma vorrei fare di tutto per poter ottimizzare il tutto.
In attesa delle vostre risposte, vi ringrazio in anticipo.
EDIT: aggiungo info
sudo hdparm -i /dev/sda
Codice: Seleziona tutto
/dev/sda:
Model=TOSHIBA MQ01ABD050, FwRev=AX003J, SerialNo=925IS3D3S
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=976773168
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive conforms to: Unspecified: ATA/ATAPI-3,4,5,6,7
* signifies the current active mode
sudo hdparm -I /dev/sda
Codice: Seleziona tutto
/dev/sda:
ATA device, with non-removable media
Model Number: TOSHIBA MQ01ABD050
Serial Number: 925IS3D3S
Firmware Revision: AX003J
Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
Supported: 8 7 6 5
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 976773168
Logical Sector size: 512 bytes
Physical Sector size: 4096 bytes
Logical Sector-0 offset: 0 bytes
device size with M = 1024*1024: 476940 MBytes
device size with M = 1000*1000: 500107 MBytes (500 GB)
cache/buffer size = 8192 KBytes
Form Factor: 2.5 inch
Nominal Media Rotation Rate: 5400
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: 254
DMA: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
SET_MAX security extension
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* IDLE_IMMEDIATE with UNLOAD
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Segmented DOWNLOAD_MICROCODE
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Gen3 signaling speed (6.0Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
* Idle-Unload when NCQ is active
* Host automatic Partial to Slumber transitions
* Device automatic Partial to Slumber transitions
* READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
* DMA Setup Auto-Activate optimization
* Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Write Same (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
supported: enhanced erase
116min for SECURITY ERASE UNIT. 116min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 5000039445e81b18
NAA : 5
IEEE OUI : 000039
Unique ID : 445e81b18
Checksum: correct
inxi -Fz
Codice: Seleziona tutto
inxi -Fz
System: Host: ************* Kernel: 4.18.0-18-generic x86_64 bits: 64 Desktop: Gnome 3.28.3
Distro: Ubuntu 18.04.2 LTS
Machine: Device: laptop System: Acer product: Aspire V3-571G v: V2.07 serial: N/A
Mobo: Acer model: VA50_HC_CR v: Type2 - Board Version serial: N/A
UEFI [Legacy]: Acer v: V2.07 date: 10/15/2012
Battery BAT1: charge: 4.0 Wh 100.0% condition: 4.0/48.8 Wh (8%)
CPU: Quad core Intel Core i7-3632QM (-MT-MCP-) cache: 6144 KB
clock speeds: max: 3200 MHz 1: 1201 MHz 2: 1206 MHz 3: 1202 MHz 4: 1211 MHz 5: 1199 MHz 6: 1209 MHz
7: 1204 MHz 8: 1199 MHz
Graphics: Card-1: Intel 3rd Gen Core processor Graphics Controller
Card-2: NVIDIA GF117M [GeForce 610M/710M/810M/820M / GT 620M/625M/630M/720M]
Display Server: x11 (X.Org 1.20.1 ) drivers: modesetting,nvidia (unloaded: fbdev,vesa,nouveau)
Resolution: 1366x768@60.01hz, 1680x1050@59.95hz
OpenGL: renderer: GeForce 710M/PCIe/SSE2 version: 4.4.0 NVIDIA 340.107
Audio: Card Intel 7 Series/C216 Family High Definition Audio Controller driver: snd_hda_intel
Sound: Advanced Linux Sound Architecture v: k4.18.0-18-generic
Network: Card-1: Broadcom and subsidiaries NetLink BCM57785 Gigabit Ethernet PCIe driver: tg3
IF: enp2s0f0 state: up speed: 1000 Mbps duplex: full mac: <filter>
Card-2: Qualcomm Atheros AR9462 Wireless Network Adapter driver: ath9k
IF: wlp3s0 state: up mac: <filter>
Drives: HDD Total Size: 500.1GB (10.0% used)
ID-1: /dev/sda model: TOSHIBA_MQ01ABD0 size: 500.1GB
Partition: ID-1: / size: 179G used: 47G (28%) fs: ext4 dev: /dev/sda5
RAID: No RAID devices: /proc/mdstat, md_mod kernel module present
Sensors: System Temperatures: cpu: 58.0C mobo: N/A gpu: 55C
Fan Speeds (in rpm): cpu: N/A
Info: Processes: 336 Uptime: 6 min Memory: 1814.2/3764.9MB Client: Shell (bash) inxi: 2.3.56