guarda anche : dmesg
ottengo questo...in effetti qualcosa dice a proposito di eth0 ma non so interpretarlo...
[ 0.160637] PCI: not using MMCONFIG
[ 0.160915] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
[ 0.160922] PCI: Using configuration type 1 for base access
[ 0.165643] bio: create slab <bio-0> at 0
[ 0.169082] ACPI: EC: Look up EC in DSDT
[ 0.176366] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.193522] ACPI: Interpreter enabled
[ 0.193534] ACPI: (supports S0 S3 S4 S5)
[ 0.193598] ACPI: Using IOAPIC for interrupt routing
[ 0.223976] ACPI Warning: Incorrect checksum in table [OEMB] - 0xFC, should be 0xFB (20100428/tbutils-314)
[ 0.224448] ACPI: No dock devices found.
[ 0.224460] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.224820] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.225530] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.225541] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.225551] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.225561] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000dffff]
[ 0.225570] pci_root PNP0A08:00: host bridge window [mem 0x3f800000-0xffffffff]
[ 0.225686] pci 0000:00:02.0: reg 10: [mem 0xfea80000-0xfeafffff]
[ 0.225698] pci 0000:00:02.0: reg 14: [io 0xec00-0xec07]
[ 0.225711] pci 0000:00:02.0: reg 18: [mem 0xd0000000-0xdfffffff pref]
[ 0.225723] pci 0000:00:02.0: reg 1c: [mem 0xfea40000-0xfea7ffff]
[ 0.225840] pci 0000:00:1b.0: reg 10: [mem 0xfea38000-0xfea3bfff 64bit]
[ 0.225904] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.225915] pci 0000:00:1b.0: PME# disabled
[ 0.226020] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.226032] pci 0000:00:1c.0: PME# disabled
[ 0.226114] pci 0000:00:1d.0: reg 20: [io 0xe880-0xe89f]
[ 0.226192] pci 0000:00:1d.1: reg 20: [io 0xe800-0xe81f]
[ 0.226268] pci 0000:00:1d.2: reg 20: [io 0xe480-0xe49f]
[ 0.226345] pci 0000:00:1d.3: reg 20: [io 0xe400-0xe41f]
[ 0.226421] pci 0000:00:1d.7: reg 10: [mem 0xfea37c00-0xfea37fff]
[ 0.226493] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.226504] pci 0000:00:1d.7: PME# disabled
[ 0.226677] pci 0000:00:1f.0: quirk: [io 0x0800-0x087f] claimed by ICH6 ACPI/GPIO/TCO
[ 0.226689] pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by ICH6 GPIO
[ 0.226700] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff)
[ 0.226767] pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
[ 0.226781] pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
[ 0.226795] pci 0000:00:1f.1: reg 18: [io 0x08f0-0x08f7]
[ 0.226808] pci 0000:00:1f.1: reg 1c: [io 0x08f8-0x08fb]
[ 0.226822] pci 0000:00:1f.1: reg 20: [io 0xffa0-0xffaf]
[ 0.226886] pci 0000:00:1f.2: reg 10: [io 0xe080-0xe087]
[ 0.226900] pci 0000:00:1f.2: reg 14: [io 0xe000-0xe003]
[ 0.226915] pci 0000:00:1f.2: reg 18: [io 0xdc00-0xdc07]
[ 0.226929] pci 0000:00:1f.2: reg 1c: [io 0xd880-0xd883]
[ 0.226945] pci 0000:00:1f.2: reg 20: [io 0xd800-0xd80f]
[ 0.226988] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.226998] pci 0000:00:1f.2: PME# disabled
[ 0.227067] pci 0000:00:1f.3: reg 20: [io 0x0400-0x041f]
[ 0.227222] pci 0000:01:00.0: reg 10: [mem 0xfebc0000-0xfebfffff 64bit]
[ 0.227268] pci 0000:01:00.0: reg 30: [mem 0xfeba0000-0xfebbffff pref]
[ 0.227321] pci 0000:01:00.0: PME# supported from D3hot D3cold
[ 0.227332] pci 0000:01:00.0: PME# disabled
[ 0.227359] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.227382] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.227393] pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.227405] pci 0000:00:1c.0: bridge window [mem 0xfeb00000-0xfebfffff]
[ 0.227419] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.227515] pci 0000:00:1e.0: PCI bridge to [bus 02-02] (subtractive decode)
[ 0.227526] pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.227538] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.227552] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.227562] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.227571] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.227580] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.227590] pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
[ 0.227599] pci 0000:00:1e.0: bridge window [mem 0x3f800000-0xffffffff] (subtractive decode)
[ 0.227621] pci_bus 0000:00: on NUMA node 0
[ 0.227640] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.228057] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.228574] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.254870] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.255174] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.255511] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 0.255812] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.256132] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.256440] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.256772] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.257079] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.257229] HEST: Table is not found!
[ 0.257488] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.257517] vgaarb: loaded
[ 0.258096] SCSI subsystem initialized
[ 0.258343] libata version 3.00 loaded.
[ 0.258593] usbcore: registered new interface driver usbfs
[ 0.258646] usbcore: registered new interface driver hub
[ 0.258744] usbcore: registered new device driver usb
[ 0.259248] ACPI: WMI: Mapper loaded
[ 0.259255] PCI: Using ACPI for IRQ routing
[ 0.259267] PCI: pci_cache_line_size set to 64 bytes
[ 0.259385] reserve RAM buffer: 000000000009f400 - 000000000009ffff
[ 0.259395] reserve RAM buffer: 000000003f7b0000 - 000000003fffffff
[ 0.259730] NetLabel: Initializing
[ 0.259737] NetLabel: domain hash size = 128
[ 0.259743] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.259778] NetLabel: unlabeled traffic allowed by default
[ 0.259902] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.259915] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.259929] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.268092] Switching to clocksource tsc
[ 0.297374] AppArmor: AppArmor Filesystem Enabled
[ 0.297419] pnp: PnP ACPI init
[ 0.297472] ACPI: bus type pnp registered
[ 0.311255] pnp: PnP ACPI: found 16 devices
[ 0.311265] ACPI: ACPI bus type pnp unregistered
[ 0.311275] PnPBIOS: Disabled by ACPI PNP
[ 0.311315] system 00:01: [mem 0xfed13000-0xfed19fff] has been reserved
[ 0.311341] system 00:08: [io 0x0a00-0x0a0f] has been reserved
[ 0.311350] system 00:08: [io 0x0a10-0x0a1f] has been reserved
[ 0.311359] system 00:08: [io 0x0a20-0x0a2f] has been reserved
[ 0.311368] system 00:08: [io 0x0a30-0x0a3f] has been reserved
[ 0.311388] system 00:09: [io 0x04d0-0x04d1] has been reserved
[ 0.311398] system 00:09: [io 0x0800-0x087f] has been reserved
[ 0.311407] system 00:09: [io 0x0480-0x04bf] has been reserved
[ 0.311418] system 00:09: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.311429] system 00:09: [mem 0xfed20000-0xfed8ffff] has been reserved
[ 0.311466] system 00:0c: [mem 0xffc00000-0xfff7ffff] has been reserved
[ 0.311485] system 00:0d: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.311495] system 00:0d: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.311520] system 00:0e: [mem 0xe0000000-0xe3ffffff] has been reserved
[ 0.311539] system 00:0f: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.311550] system 00:0f: [mem 0x000c0000-0x000cffff] could not be reserved
[ 0.311560] system 00:0f: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.311571] system 00:0f: [mem 0x00100000-0x3f7fffff] could not be reserved
[ 0.352042] pci 0000:00:1c.0: BAR 15: assigned [mem 0x3f800000-0x3f9fffff 64bit pref]
[ 0.352057] pci 0000:00:1c.0: BAR 13: assigned [io 0x1000-0x1fff]
[ 0.352069] pci 0000:00:1c.0: PCI bridge to [bus 01-01]
[ 0.352078] pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff]
[ 0.352090] pci 0000:00:1c.0: bridge window [mem 0xfeb00000-0xfebfffff]
[ 0.352102] pci 0000:00:1c.0: bridge window [mem 0x3f800000-0x3f9fffff 64bit pref]
[ 0.352116] pci 0000:00:1e.0: PCI bridge to [bus 02-02]
[ 0.352123] pci 0000:00:1e.0: bridge window [io disabled]
[ 0.352133] pci 0000:00:1e.0: bridge window [mem disabled]
[ 0.352142] pci 0000:00:1e.0: bridge window [mem pref disabled]
[ 0.352170] pci 0000:00:1c.0: enabling device (0106 -> 0107)
[ 0.352189] alloc irq_desc for 16 on node -1
[ 0.352196] alloc kstat_irqs on node -1
[ 0.352216] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.352230] pci 0000:00:1c.0: setting latency timer to 64
[ 0.352248] pci 0000:00:1e.0: setting latency timer to 64
[ 0.352260] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.352269] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.352278] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.352288] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.352296] pci_bus 0000:00: resource 8 [mem 0x3f800000-0xffffffff]
[ 0.352306] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff]
[ 0.352315] pci_bus 0000:01: resource 1 [mem 0xfeb00000-0xfebfffff]
[ 0.352325] pci_bus 0000:01: resource 2 [mem 0x3f800000-0x3f9fffff 64bit pref]
[ 0.352335] pci_bus 0000:02: resource 4 [io 0x0000-0x0cf7]
[ 0.352344] pci_bus 0000:02: resource 5 [io 0x0d00-0xffff]
[ 0.352352] pci_bus 0000:02: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.352361] pci_bus 0000:02: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.352369] pci_bus 0000:02: resource 8 [mem 0x3f800000-0xffffffff]
[ 0.352487] NET: Registered protocol family 2
[ 0.352691] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.353589] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.354785] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.355408] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.355450] TCP reno registered
[ 0.355481] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.355512] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.355861] NET: Registered protocol family 1
[ 0.355911] pci 0000:00:02.0: Boot video device
[ 0.356076] PCI: CLS 32 bytes, default 64
[ 0.356743] cpufreq-nforce2: No nForce2 chipset.
[ 0.356849] Scanning for low memory corruption every 60 seconds
[ 0.357221] audit: initializing netlink socket (disabled)
[ 0.357251] type=2000 audit(1287302693.352:1): initialized
[ 0.381421] highmem bounce pool size: 64 pages
[ 0.381440] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.386897] VFS: Disk quotas dquot_6.5.2
[ 0.387109] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.389332] fuse init (API version 7.14)
[ 0.389670] msgmni has been set to 1709
[ 0.390666] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.390677] io scheduler noop registered
[ 0.390683] io scheduler deadline registered
[ 0.390737] io scheduler cfq registered (default)
[ 0.391036] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.391090] alloc irq_desc for 40 on node -1
[ 0.391097] alloc kstat_irqs on node -1
[ 0.391119] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[ 0.391388] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.391579] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.391913] intel_idle: MWAIT substates: 0x10
[ 0.391921] intel_idle: v0.4 model 0x1C
[ 0.391927] intel_idle: lapic_timer_reliable_states 0x6
[ 0.392319] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.392343] ACPI: Power Button [PWRB]
[ 0.392509] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.392521] ACPI: Power Button [PWRF]
[ 0.393217] ACPI: acpi_idle yielding to intel_idle
[ 0.408133] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.408161] ACPI: Thermal Zone [THRM] (30 C)
[ 0.408363] ERST: Table is not found!
[ 0.409119] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.409318] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.410141] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.414584] brd: module loaded
[ 0.415685] isapnp: Scanning for PnP cards...
[ 0.416539] loop: module loaded
[ 0.417159] ata_piix 0000:00:1f.1: version 2.13
[ 0.417191] alloc irq_desc for 18 on node -1
[ 0.417197] alloc kstat_irqs on node -1
[ 0.417217] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.417297] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 0.417468] scsi0 : ata_piix
[ 0.417726] scsi1 : ata_piix
[ 0.421558] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 0.421568] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 0.421628] alloc irq_desc for 19 on node -1
[ 0.421634] alloc kstat_irqs on node -1
[ 0.421649] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.421661] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 0.421737] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 0.421877] scsi2 : ata_piix
[ 0.422061] scsi3 : ata_piix
[ 0.426519] ata3: SATA max UDMA/133 cmd 0xe080 ctl 0xe000 bmdma 0xd800 irq 19
[ 0.426529] ata4: SATA max UDMA/133 cmd 0xdc00 ctl 0xd880 bmdma 0xd808 irq 19
[ 0.427807] Fixed MDIO Bus: probed
[ 0.427947] PPP generic driver version 2.4.2
[ 0.428113] tun: Universal TUN/TAP device driver, 1.6
[ 0.428120] tun: (C) 1999-2004 Max Krasnyansky <
[email protected]>
[ 0.428370] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.428419] alloc irq_desc for 23 on node -1
[ 0.428426] alloc kstat_irqs on node -1
[ 0.428443] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.428486] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.428496] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.428604] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 0.428652] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 0.428671] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.432555] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.432607] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfea37c00
[ 0.455738] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.456140] hub 1-0:1.0: USB hub found
[ 0.456155] hub 1-0:1.0: 8 ports detected
[ 0.456361] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.456412] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.456498] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.456517] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.456526] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.456657] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.456705] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e880
[ 0.457080] hub 2-0:1.0: USB hub found
[ 0.457095] hub 2-0:1.0: 2 ports detected
[ 0.457235] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.457250] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.457259] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.457365] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 0.457405] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e800
[ 0.457760] hub 3-0:1.0: USB hub found
[ 0.457774] hub 3-0:1.0: 2 ports detected
[ 0.457915] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.457930] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.457938] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.458045] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 0.458106] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e480
[ 0.458492] hub 4-0:1.0: USB hub found
[ 0.458505] hub 4-0:1.0: 2 ports detected
[ 0.458645] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 0.458660] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 0.458669] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 0.458773] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 0.458831] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e400
[ 0.459189] hub 5-0:1.0: USB hub found
[ 0.459202] hub 5-0:1.0: 2 ports detected
[ 0.459566] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 0.459573] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 0.459774] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.460078] mice: PS/2 mouse device common for all mice
[ 0.460429] rtc_cmos 00:03: RTC can wake from S4
[ 0.460552] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.460593] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.460966] device-mapper: uevent: version 1.0.3
[ 0.465574] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised:
[email protected]
[ 0.479846] device-mapper: multipath: version 1.1.1 loaded
[ 0.479857] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.484585] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 0.485040] EISA: Probing bus 0 at eisa.0
[ 0.485049] EISA: Cannot allocate resource for mainboard
[ 0.485058] Cannot allocate resource for EISA slot 1
[ 0.485066] Cannot allocate resource for EISA slot 2
[ 0.485074] Cannot allocate resource for EISA slot 3
[ 0.485081] Cannot allocate resource for EISA slot 4
[ 0.485089] Cannot allocate resource for EISA slot 5
[ 0.485097] Cannot allocate resource for EISA slot 6
[ 0.485105] Cannot allocate resource for EISA slot 7
[ 0.485113] Cannot allocate resource for EISA slot 8
[ 0.485119] EISA: Detected 0 cards.
[ 0.499676] cpuidle: using governor ladder
[ 0.499884] cpuidle: using governor menu
[ 0.500767] TCP cubic registered
[ 0.501210] NET: Registered protocol family 10
[ 0.502286] lo: Disabled Privacy Extensions
[ 0.502944] NET: Registered protocol family 17
[ 0.503082] Using IPI No-Shortcut mode
[ 0.503380] PM: Resume from disk failed.
[ 0.503428] registered taskstats version 1
[ 0.503849] Magic number: 14:660:68
[ 0.503977] rtc_cmos 00:03: setting system clock to 2010-10-17 08:04:54 UTC (1287302694)
[ 0.503986] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.503992] EDD information not available.
[ 0.608001] ata4.01: NODEV after polling detection
[ 0.615654] ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-T50N, RH03, max UDMA/133
[ 0.632055] ata4.00: configured for UDMA/133
[ 0.634499] ata3.00: ATA-8: STM3500418AS, CC34, max UDMA/133
[ 0.634510] ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 0.690909] ata3.00: configured for UDMA/133
[ 0.769373] isapnp: No Plug & Play device found
[ 0.769784] scsi 2:0:0:0: Direct-Access ATA STM3500418AS CC34 PQ: 0 ANSI: 5
[ 0.770301] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 0.770751] sd 2:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 0.770978] sd 2:0:0:0: [sda] Write Protect is off
[ 0.770990] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.771090] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.771667] sda:
[ 0.773111] scsi 3:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T50N RH03 PQ: 0 ANSI: 5
[ 0.778757] sda1 sda2 <sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 0.784730] Uniform CD-ROM driver Revision: 3.20
[ 0.785072] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 0.785263] sr 3:0:0:0: Attached scsi generic sg1 type 5
[ 0.807094] sda5 >
[ 0.808241] sd 2:0:0:0: [sda] Attached SCSI disk
[ 0.869424] Freeing initrd memory: 10512k freed
[ 0.880276] Freeing unused kernel memory: 684k freed
[ 0.881195] Write protecting the kernel text: 4932k
[ 0.881289] Write protecting the kernel read-only data: 1976k
[ 0.927107] udev[83]: starting version 163
[ 0.951387] usb 4-1: new low speed USB device using uhci_hcd and address 2
[ 1.159297] Atheros(R) L2 Ethernet Driver - version 2.2.3
[ 1.159307] Copyright (c) 2007 Atheros Corporation.
[ 1.159381] atl2 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.159403] atl2 0000:01:00.0: setting latency timer to 64
[ 1.377835] EXT3-fs: barriers not enabled
[ 1.390594] usbcore: registered new interface driver hiddev
[ 1.391746] kjournald starting. Commit interval 5 seconds
[ 1.392208] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 1.404238] input: HID 062a:0000 as /devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.0/input/input3
[ 1.404974] generic-usb 0003:062A:0000.0001: input,hidraw0: USB HID v1.10 Mouse [HID 062a:0000] on usb-0000:00:1d.2-1/input0
[ 1.405535] usbcore: registered new interface driver usbhid
[ 1.405544] usbhid: USB HID core driver
[ 25.581214] udev[305]: starting version 163
[ 25.655942] Adding 2980020k swap on /dev/sda5. Priority:-1 extents:1 across:2980020k
[ 25.888795] lp: driver loaded but no devices found
[ 25.941423] intel_rng: FWH not detected
[ 26.103026] leds_ss4200: no LED devices found
[ 26.161340] EXT3-fs (sda1): using internal journal
[ 26.174910] Linux agpgart interface v0.103
[ 26.396900] agpgart-intel 0000:00:00.0: Intel 945G Chipset
[ 26.397338] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[ 26.422595] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[ 26.594640] type=1400 audit(1287302720.587:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient3" pid=540 comm="apparmor_parser"
[ 26.595540] type=1400 audit(1287302720.587:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=540 comm="apparmor_parser"
[ 26.596155] type=1400 audit(1287302720.591:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=540 comm="apparmor_parser"
[ 26.901214] [drm] Initialized drm 1.1.0 20060810
[ 27.293158] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 27.293174] i915 0000:00:02.0: setting latency timer to 64
[ 27.350788] alloc irq_desc for 41 on node -1
[ 27.350799] alloc kstat_irqs on node -1
[ 27.350826] atl2 0000:01:00.0: irq 41 for MSI/MSI-X
[ 27.351460] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 27.416667] [drm] set up 7M of stolen space
[ 27.419231] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 27.419760] [drm] initialized overlay support
[ 27.483549] type=1400 audit(1287302721.475:5): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=716 comm="apparmor_parser"
[ 27.487661] type=1400 audit(1287302721.479:6): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=717 comm="apparmor_parser"
[ 27.488537] type=1400 audit(1287302721.483:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=717 comm="apparmor_parser"
[ 27.489179] type=1400 audit(1287302721.483:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=717 comm="apparmor_parser"
[ 27.497819] type=1400 audit(1287302721.491:9): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=718 comm="apparmor_parser"
[ 27.511789] type=1400 audit(1287302721.503:10): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=718 comm="apparmor_parser"
[ 27.515127] type=1400 audit(1287302721.507:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/freshclam" pid=720 comm="apparmor_parser"
[ 27.578608] atl2: eth0 NIC Link is Up<10 Mbps Full Duplex>
[ 27.579193] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 27.732550] Console: switching to colour frame buffer device 128x48
[ 27.745155] fb0: inteldrmfb frame buffer device
[ 27.745162] drm: registered panic notifier
[ 27.765239] Slow work thread pool: Starting up
[ 27.769582] Slow work thread pool: Ready
[ 27.769611] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 27.770050] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 27.770136] alloc irq_desc for 42 on node -1
[ 27.770144] alloc kstat_irqs on node -1
[ 27.770168] HDA Intel 0000:00:1b.0: irq 42 for MSI/MSI-X
[ 27.770229] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 27.853731] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 27.853741] apm: disabled - APM is not SMP safe.
[ 28.112423] ppdev: user-space parallel port driver
[ 37.992013] eth0: no IPv6 routers present
[ 324.092043] usb 4-2: new full speed USB device using uhci_hcd and address 3
[ 324.416367] usbcore: registered new interface driver cdc_ether
[ 324.705299] rndis_host 4-2:1.0: RNDIS_MSG_QUERY(0x00010202) failed, -47
[ 324.713047] rndis_host 4-2:1.0: eth1: register 'rndis_host' at usb-0000:00:1d.2-2, RNDIS device, 80:00:60:0f:e8:00
[ 324.713262] usbcore: registered new interface driver rndis_host
[ 324.832065] cfg80211: Calling CRDA to update world regulatory domain
[ 324.871542] cfg80211: World regulatory domain updated:
[ 324.871550] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 324.871558] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 324.871565] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 324.871572] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 324.871579] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 324.871585] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 324.897701] usbcore: registered new interface driver rndis_wlan
[ 325.045750] udev[390]: renamed network interface eth1 to eth2
[ 335.336022] eth2: no IPv6 routers present
[ 558.790853] show_signal_msg: 12 callbacks suppressed
[ 558.790868] gnome-keyring-d[1446]: segfault at 83e58955 ip 08055ca9 sp bfc869f0 error 4 in gnome-keyring-daemon[8048000+bf000]
[ 2569.628078] atl2: eth0 NIC Link is Down
[ 2587.356223] atl2: eth0 NIC Link is Up<10 Mbps Full Duplex>
[ 2587.872740] atl2: eth0 NIC Link is Down
[ 2591.083127] atl2: eth0 NIC Link is Up<10 Mbps Full Duplex>
[ 2649.207429] atl2: eth0 NIC Link is Down
[ 2656.072953] atl2: eth0 NIC Link is Up<100 Mbps Full Duplex>
[ 2656.073297] atl2: eth0 NIC Link is Down
[ 2662.045900] atl2: eth0 NIC Link is Up<100 Mbps Full Duplex>
[ 2662.046356] atl2: eth0 NIC Link is Down
[ 2663.608353] atl2: eth0 NIC Link is Up<10 Mbps Full Duplex>
[ 2671.047299] atl2: eth0 NIC Link is Down
[ 2674.453514] atl2: eth0 NIC Link is Up<10 Mbps Half Duplex>
[ 2870.062517] atl2: eth0 NIC Link is Down
[ 2886.048427] atl2: eth0 NIC Link is Up<10 Mbps Full Duplex>
[ 3756.653171] atl2 0000:01:00.0: irq 41 for MSI/MSI-X
[ 3756.653368] atl2: eth0 NIC Link is Up<10 Mbps Full Duplex>
[ 3756.653773] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3756.654292] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 3767.328015] eth0: no IPv6 routers present
[ 3767.456022] eth2: no IPv6 routers present
[24238.448066] usb 4-2: USB disconnect, address 3
[24238.450001] rndis_host 4-2:1.0: eth2: unregister 'rndis_host' usb-0000:00:1d.2-2, RNDIS device
[24267.300356] atl2 0000:01:00.0: irq 41 for MSI/MSI-X
[24267.301094] ADDRCONF(NETDEV_UP): eth0: link is not ready
[24267.303053] atl2: eth0 NIC Link is Up<10 Mbps Full Duplex>
[24267.303677] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[24278.016015] eth0: no IPv6 routers present
[32780.660810] atl2 0000:01:00.0: irq 41 for MSI/MSI-X
[32780.661056] atl2: eth0 NIC Link is Up<10 Mbps Full Duplex>
[32780.661505] ADDRCONF(NETDEV_UP): eth0: link is not ready
[32780.662022] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[32791.104019] eth0: no IPv6 routers present
[45302.962581] atl2 0000:01:00.0: irq 41 for MSI/MSI-X
[45302.962752] atl2: eth0 NIC Link is Up<10 Mbps Full Duplex>
[45302.963249] ADDRCONF(NETDEV_UP): eth0: link is not ready
[45302.963770] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[45313.864022] eth0: no IPv6 routers present