Stevejedi
02-08-2010, 16:37
Salve a tutti. Ho da poco sotto avuto sotto mano il q9550s assieme a delle nuove Dominator 2x2 GB prese per andare su di OC (prima avevo le xms2 a 800mhz). Vado benissimo su 3.4GHz (da testare in RS, ma promette molto bene), ma non riesco a superare i 400 MHz di FSB.
A 450 MHz passo il boot, ma si blocca durante il caricamento di Windows (la bandiera non si compone, o si blocca, o rimane vibrante in loop).
A 500 MHz (con moltiplicatore a 7x), il boot mi segnala 500x7, ma in Windows mi scende a 333x7. Strano!?!?!
EDIT: Appena provato a 533x6, boota su windows... ma sempre a 333x6. Assurdo
Che devo fare per salire di FSB??
Per un quadro completo vi posto la configurazione esatta:
DFI Lanparty UT P45-T2RS (bios aggiornato)
Intel Core 2 Quad Q9550s - Dissipatore Noctua NH-U12P - Pasta Diamond 7 Carati
Corsair Dominator Twin2x4096-8500C5D (2x CM2X2048-8500C5DF) rev 1.2 (chip PSC.F-Die 128MX8) 2x2GB
Sapphire 5850 Vapor-X 2GB
Western Digital Caviar Blue 400GB Sata II
Corsair HX 850W
Windows 7 Professional x64bit
Per evitare problemi legati alle periferiche usb utilizzo una tastiera PS/2 nel boot.
Vi porto i test che ho effettuato:
Test 1 = 400 x 8.5
Test 2 = 450 x 8.5
Test 1:
Ho raggiunto -semplicemente- un 400x8.5 con le RAM a 400MHz e timings rilassati. Con la seguente configurazione BIOS:
Genie BIOS Page
- BIOS Field
Exit Setup Shutdown……Mode 2
Shutdown After AC Loss……Enabled
AC Shutdown Free……Enabled
OC Fail Retry Counter……1
OC Fail CMOS Reload……Disabled
CPU Clock Ratio……8.5x
CPU N/2 Ratio……Enabled
Target CPU Clock……3400 MHz
CPU Clock……400 MHz
Boot Up Clock……Auto
CPU Clock Amplitude……800mV
CPU Clock0 Skew……0ps
CPU Clock1 Skew……0ps
DRAM Speed……400/800
Target DRAM Speed……DDR2 800
PCIE Clock……100 MHz
PCIE Slot Config……1X 1X
CPU Spread Spectrum……Disabled
PCIE Spread Spectrum……Disabled
- CPU Feature Page
Thermal Management Control……Disabled
PPM (EIST) Mode……Disabled
Limit CPUID MaxVal……Disabled
C1E Function……Disabled
Execute Disable Bit……Enabled
Virtualization Technology……Enabled
Core Multi Processing……Enabled
- DRAM Timing
Enhance Data Transmitting……Auto
Enhance Addressing……Auto
T2 Dispatch……Auto
Flex Memory Mode……Auto
Cas Latnecy Time (tCL)……Auto
RAS# to CAS# Delay (tCRD)……Auto
RAS# Precharge Time (tRP)……Auto
Precharge Delay (tRAS)……Auto
All Precharge to Act……Auto
REF to ACT Delay (tRFC)……Auto
Performance LVL (Read Delay)……Auto
Read delay phase adjust……N/A
Write to PRE Delay (tWR)……Auto
Rank Write to Read (tWTR)……Auto
ACT to ACT Delay (tRRD)……Auto
Read to Write Delay (tRDWR)……Auto
Ranks Write to Write (tWRWR)……Auto
Ranks Write to Read (tWRRD)……Auto
Read CAS# Precharge (tRTP)……Auto
All PRE to Refresh……Auto
- Clock Setting Fine Delay (tutti i valori si sono impostati automaticamente)
DLL and RCOMP Settings……Auto
CH1 DRAM Default Skew……Model 0
CH2 DRAM Default Skew……Model 0
RCOMP Setting…Model 0
Fine Delay Step Degree……70ps
Ch1 Clock Crossing Setting……Auto
DIMM1 Clock Fine Delay……2032ps
DIMM2 Clock Fine Delay……2032ps
Ch1 Control0 Fine Delay……234ps
Ch1 Control1 Fine Delay……234ps
Ch1 Control2 Fine Delay……234ps
Ch1 Control3 Fine Delay……234ps
Ch1 Command Fine Delay……344ps
Ch2 Clock Crossing Setting……Auto
DIMM3 Clock Fine Delay……1744ps
DIMM4 Clock Fine Delay……1744ps
Ch2 Control0 Fine Delay……42ps
Ch2 Control1 Fine Delay……42ps
Ch2 Control2 Fine Delay……42ps
Ch2 Control3 Fine Delay……42ps
Ch2 Command Fine Delay……344ps
Ch1Ch2 Common Clock Setting……Auto
Ch1 RDCAS GNT-Chip Delay……Auto
Ch1 WRCAS GNT-Chip Delay……Auto
Ch1 Command to CS Delay……Auto
Ch2 RDCAS GNT-Chip Delay…Auto
Ch2 WRCAS GNT-Chip Delay……Auto
Ch2 Command to CS Delay……Auto
- Read Delay Phase Adjust (tutti i valori si sono impostati automaticamente)
Ch1 Read Delay Phase (4~0)……7-7-7-7-7
Channel 1 Phase 0 Pull-in……Auto
Channel 1 Phase 1 Pull-in……Auto
Channel 1 Phase 2 Pull-in……Auto
Channel 1 Phase 3 Pull-in……Auto
Ch2 Read Delay Phase (4~0)……7-7-7-7-7
Channel 2 Phase 0 Pull-in……Auto
Channel 2 Phase 1 Pull-in……Auto
Channel 2 Phase 2 Pull-in……Auto
Channel 2 Phase 3 Pull-in……Auto
- Voltage Settings
CPU VID Control……Auto 1.1575 V (è il VID del processore)
CPU VID Special Add Limit……Enabled
CPU VID Special Add……Auto
DRAM Voltage Control……1.91V (in automatico è il valore impostato da bios sulle ram)
SB Core/CPU PLL Voltage……1.55V
NB Core Voltage……1.140V
CPU VTT Voltage……1.200V
Vcore Droop Control……Disabled
Clockgen Voltage Control……3.45V
GTL+ Buffers Strength……Strong
CPU GTL 0 REF Volt……0.6700
CPU GTL 1 REF Volt……0.6700
CPU GTL 2 REF Volt……0.6700
CPU GTL 3 REF Volt……0.6700
NB GTL 0 Ref Volt……0.6700
NB GTL 1 Ref Volt……0.6700
FSB Vref……Auto
________________________________________
Test 2 (450x8.5)
In grassetto i cambiamenti rispetto al precedente
Genie BIOS Page
- BIOS Field
Exit Setup Shutdown……Mode 2
Shutdown After AC Loss……Enabled
AC Shutdown Free……Enabled
OC Fail Retry Counter……1
OC Fail CMOS Reload……Disabled
CPU Clock Ratio……8.5x
CPU N/2 Ratio……Enabled
Target CPU Clock……3825 MHz
CPU Clock……450 MHz
Boot Up Clock……Auto
CPU Clock Amplitude……800mV
CPU Clock0 Skew……200ps
CPU Clock1 Skew……200ps
DRAM Speed……266/667
Target DRAM Speed……DDR2 1128
PCIE Clock……100 MHz
PCIE Slot Config……1X 1X
CPU Spread Spectrum……Disabled
PCIE Spread Spectrum……Disabled
- CPU Feature Page
Thermal Management Control……Disabled
PPM (EIST) Mode……Disabled
Limit CPUID MaxVal……Disabled
C1E Function……Disabled
Execute Disable Bit……Disabled
Virtualization Technology……Disabled
Core Multi Processing……Enabled
- DRAM Timing
Enhance Data Transmitting……Auto
Enhance Addressing……Auto
T2 Dispatch……Auto
Flex Memory Mode……Auto
Cas Latnecy Time (tCL)……Auto (provato anche con 5)
RAS# to CAS# Delay (tCRD)……Auto (provato anche con 5)
RAS# Precharge Time (tRP)……Auto (provato anche con 5)
Precharge Delay (tRAS)……Auto (provato anche con 15)
All Precharge to Act……Auto
REF to ACT Delay (tRFC)……Auto
Performance LVL (Read Delay)……Auto
Read delay phase adjust……N/A
Write to PRE Delay (tWR)……Auto
Rank Write to Read (tWTR)……Auto
ACT to ACT Delay (tRRD)……Auto
Read to Write Delay (tRDWR)……Auto
Ranks Write to Write (tWRWR)……Auto
Ranks Write to Read (tWRRD)……Auto
Read CAS# Precharge (tRTP)……Auto
All PRE to Refresh……Auto
- Clock Setting Fine Delay (i valori numerici si sono impostati automaticamente)
DLL and RCOMP Settings……Auto
CH1 DRAM Default Skew……Model 3
CH2 DRAM Default Skew……Model 3
RCOMP Setting…Model 1
Fine Delay Step Degree……70ps
Ch1 Clock Crossing Setting……More Relaxed (provato anche in Auto)
DIMM1 Clock Fine Delay……2396ps
DIMM2 Clock Fine Delay……2396ps
Ch1 Control0 Fine Delay……268ps
Ch1 Control1 Fine Delay……268ps
Ch1 Control2 Fine Delay……268ps
Ch1 Control3 Fine Delay……268ps
Ch1 Command Fine Delay……394ps
Ch2 Clock Crossing Setting……More Relaxed (provato anche in Auto)
DIMM3 Clock Fine Delay……2066ps
DIMM4 Clock Fine Delay……2066ps
Ch2 Control0 Fine Delay……48ps
Ch2 Control1 Fine Delay……48ps
Ch2 Control2 Fine Delay……48ps
Ch2 Control3 Fine Delay……48ps
Ch2 Command Fine Delay……394ps
Ch1Ch2 Common Clock Setting……More Relaxed (provato anche in Auto)
Ch1 RDCAS GNT-Chip Delay……Auto
Ch1 WRCAS GNT-Chip Delay……Auto
Ch1 Command to CS Delay……Auto
Ch2 RDCAS GNT-Chip Delay…Auto
Ch2 WRCAS GNT-Chip Delay……Auto
Ch2 Command to CS Delay……Auto
- Read Delay Phase Adjust (tutti i valori si sono impostati automaticamente)
Ch1 Read Delay Phase (4~0)……7-7-7-7-7
Channel 1 Phase 0 Pull-in……Auto
Channel 1 Phase 1 Pull-in……Auto
Channel 1 Phase 2 Pull-in……Auto
Channel 1 Phase 3 Pull-in……Auto
Ch2 Read Delay Phase (4~0)……7-7-7-7-7
Channel 2 Phase 0 Pull-in……Auto
Channel 2 Phase 1 Pull-in……Auto
Channel 2 Phase 2 Pull-in……Auto
Channel 2 Phase 3 Pull-in……Auto
- Voltage Settings
CPU VID Control……1.16250 V
CPU VID Special Add Limit……Enabled
CPU VID Special Add……Auto
DRAM Voltage Control……2.11V
SB Core/CPU PLL Voltage……1.75V
NB Core Voltage……1.408V
CPU VTT Voltage……1.303V
Vcore Droop Control……Disabled
Clockgen Voltage Control……3.45V
GTL+ Buffers Strength……Strong
CPU GTL 0 REF Volt……0.6700
CPU GTL 1 REF Volt……0.6700
CPU GTL 2 REF Volt……0.6700
CPU GTL 3 REF Volt……0.6700
NB GTL 0 Ref Volt……0.6700
NB GTL 1 Ref Volt……0.6700
FSB Vref……00
A 450 MHz passo il boot, ma si blocca durante il caricamento di Windows (la bandiera non si compone, o si blocca, o rimane vibrante in loop).
A 500 MHz (con moltiplicatore a 7x), il boot mi segnala 500x7, ma in Windows mi scende a 333x7. Strano!?!?!
EDIT: Appena provato a 533x6, boota su windows... ma sempre a 333x6. Assurdo
Che devo fare per salire di FSB??
Per un quadro completo vi posto la configurazione esatta:
DFI Lanparty UT P45-T2RS (bios aggiornato)
Intel Core 2 Quad Q9550s - Dissipatore Noctua NH-U12P - Pasta Diamond 7 Carati
Corsair Dominator Twin2x4096-8500C5D (2x CM2X2048-8500C5DF) rev 1.2 (chip PSC.F-Die 128MX8) 2x2GB
Sapphire 5850 Vapor-X 2GB
Western Digital Caviar Blue 400GB Sata II
Corsair HX 850W
Windows 7 Professional x64bit
Per evitare problemi legati alle periferiche usb utilizzo una tastiera PS/2 nel boot.
Vi porto i test che ho effettuato:
Test 1 = 400 x 8.5
Test 2 = 450 x 8.5
Test 1:
Ho raggiunto -semplicemente- un 400x8.5 con le RAM a 400MHz e timings rilassati. Con la seguente configurazione BIOS:
Genie BIOS Page
- BIOS Field
Exit Setup Shutdown……Mode 2
Shutdown After AC Loss……Enabled
AC Shutdown Free……Enabled
OC Fail Retry Counter……1
OC Fail CMOS Reload……Disabled
CPU Clock Ratio……8.5x
CPU N/2 Ratio……Enabled
Target CPU Clock……3400 MHz
CPU Clock……400 MHz
Boot Up Clock……Auto
CPU Clock Amplitude……800mV
CPU Clock0 Skew……0ps
CPU Clock1 Skew……0ps
DRAM Speed……400/800
Target DRAM Speed……DDR2 800
PCIE Clock……100 MHz
PCIE Slot Config……1X 1X
CPU Spread Spectrum……Disabled
PCIE Spread Spectrum……Disabled
- CPU Feature Page
Thermal Management Control……Disabled
PPM (EIST) Mode……Disabled
Limit CPUID MaxVal……Disabled
C1E Function……Disabled
Execute Disable Bit……Enabled
Virtualization Technology……Enabled
Core Multi Processing……Enabled
- DRAM Timing
Enhance Data Transmitting……Auto
Enhance Addressing……Auto
T2 Dispatch……Auto
Flex Memory Mode……Auto
Cas Latnecy Time (tCL)……Auto
RAS# to CAS# Delay (tCRD)……Auto
RAS# Precharge Time (tRP)……Auto
Precharge Delay (tRAS)……Auto
All Precharge to Act……Auto
REF to ACT Delay (tRFC)……Auto
Performance LVL (Read Delay)……Auto
Read delay phase adjust……N/A
Write to PRE Delay (tWR)……Auto
Rank Write to Read (tWTR)……Auto
ACT to ACT Delay (tRRD)……Auto
Read to Write Delay (tRDWR)……Auto
Ranks Write to Write (tWRWR)……Auto
Ranks Write to Read (tWRRD)……Auto
Read CAS# Precharge (tRTP)……Auto
All PRE to Refresh……Auto
- Clock Setting Fine Delay (tutti i valori si sono impostati automaticamente)
DLL and RCOMP Settings……Auto
CH1 DRAM Default Skew……Model 0
CH2 DRAM Default Skew……Model 0
RCOMP Setting…Model 0
Fine Delay Step Degree……70ps
Ch1 Clock Crossing Setting……Auto
DIMM1 Clock Fine Delay……2032ps
DIMM2 Clock Fine Delay……2032ps
Ch1 Control0 Fine Delay……234ps
Ch1 Control1 Fine Delay……234ps
Ch1 Control2 Fine Delay……234ps
Ch1 Control3 Fine Delay……234ps
Ch1 Command Fine Delay……344ps
Ch2 Clock Crossing Setting……Auto
DIMM3 Clock Fine Delay……1744ps
DIMM4 Clock Fine Delay……1744ps
Ch2 Control0 Fine Delay……42ps
Ch2 Control1 Fine Delay……42ps
Ch2 Control2 Fine Delay……42ps
Ch2 Control3 Fine Delay……42ps
Ch2 Command Fine Delay……344ps
Ch1Ch2 Common Clock Setting……Auto
Ch1 RDCAS GNT-Chip Delay……Auto
Ch1 WRCAS GNT-Chip Delay……Auto
Ch1 Command to CS Delay……Auto
Ch2 RDCAS GNT-Chip Delay…Auto
Ch2 WRCAS GNT-Chip Delay……Auto
Ch2 Command to CS Delay……Auto
- Read Delay Phase Adjust (tutti i valori si sono impostati automaticamente)
Ch1 Read Delay Phase (4~0)……7-7-7-7-7
Channel 1 Phase 0 Pull-in……Auto
Channel 1 Phase 1 Pull-in……Auto
Channel 1 Phase 2 Pull-in……Auto
Channel 1 Phase 3 Pull-in……Auto
Ch2 Read Delay Phase (4~0)……7-7-7-7-7
Channel 2 Phase 0 Pull-in……Auto
Channel 2 Phase 1 Pull-in……Auto
Channel 2 Phase 2 Pull-in……Auto
Channel 2 Phase 3 Pull-in……Auto
- Voltage Settings
CPU VID Control……Auto 1.1575 V (è il VID del processore)
CPU VID Special Add Limit……Enabled
CPU VID Special Add……Auto
DRAM Voltage Control……1.91V (in automatico è il valore impostato da bios sulle ram)
SB Core/CPU PLL Voltage……1.55V
NB Core Voltage……1.140V
CPU VTT Voltage……1.200V
Vcore Droop Control……Disabled
Clockgen Voltage Control……3.45V
GTL+ Buffers Strength……Strong
CPU GTL 0 REF Volt……0.6700
CPU GTL 1 REF Volt……0.6700
CPU GTL 2 REF Volt……0.6700
CPU GTL 3 REF Volt……0.6700
NB GTL 0 Ref Volt……0.6700
NB GTL 1 Ref Volt……0.6700
FSB Vref……Auto
________________________________________
Test 2 (450x8.5)
In grassetto i cambiamenti rispetto al precedente
Genie BIOS Page
- BIOS Field
Exit Setup Shutdown……Mode 2
Shutdown After AC Loss……Enabled
AC Shutdown Free……Enabled
OC Fail Retry Counter……1
OC Fail CMOS Reload……Disabled
CPU Clock Ratio……8.5x
CPU N/2 Ratio……Enabled
Target CPU Clock……3825 MHz
CPU Clock……450 MHz
Boot Up Clock……Auto
CPU Clock Amplitude……800mV
CPU Clock0 Skew……200ps
CPU Clock1 Skew……200ps
DRAM Speed……266/667
Target DRAM Speed……DDR2 1128
PCIE Clock……100 MHz
PCIE Slot Config……1X 1X
CPU Spread Spectrum……Disabled
PCIE Spread Spectrum……Disabled
- CPU Feature Page
Thermal Management Control……Disabled
PPM (EIST) Mode……Disabled
Limit CPUID MaxVal……Disabled
C1E Function……Disabled
Execute Disable Bit……Disabled
Virtualization Technology……Disabled
Core Multi Processing……Enabled
- DRAM Timing
Enhance Data Transmitting……Auto
Enhance Addressing……Auto
T2 Dispatch……Auto
Flex Memory Mode……Auto
Cas Latnecy Time (tCL)……Auto (provato anche con 5)
RAS# to CAS# Delay (tCRD)……Auto (provato anche con 5)
RAS# Precharge Time (tRP)……Auto (provato anche con 5)
Precharge Delay (tRAS)……Auto (provato anche con 15)
All Precharge to Act……Auto
REF to ACT Delay (tRFC)……Auto
Performance LVL (Read Delay)……Auto
Read delay phase adjust……N/A
Write to PRE Delay (tWR)……Auto
Rank Write to Read (tWTR)……Auto
ACT to ACT Delay (tRRD)……Auto
Read to Write Delay (tRDWR)……Auto
Ranks Write to Write (tWRWR)……Auto
Ranks Write to Read (tWRRD)……Auto
Read CAS# Precharge (tRTP)……Auto
All PRE to Refresh……Auto
- Clock Setting Fine Delay (i valori numerici si sono impostati automaticamente)
DLL and RCOMP Settings……Auto
CH1 DRAM Default Skew……Model 3
CH2 DRAM Default Skew……Model 3
RCOMP Setting…Model 1
Fine Delay Step Degree……70ps
Ch1 Clock Crossing Setting……More Relaxed (provato anche in Auto)
DIMM1 Clock Fine Delay……2396ps
DIMM2 Clock Fine Delay……2396ps
Ch1 Control0 Fine Delay……268ps
Ch1 Control1 Fine Delay……268ps
Ch1 Control2 Fine Delay……268ps
Ch1 Control3 Fine Delay……268ps
Ch1 Command Fine Delay……394ps
Ch2 Clock Crossing Setting……More Relaxed (provato anche in Auto)
DIMM3 Clock Fine Delay……2066ps
DIMM4 Clock Fine Delay……2066ps
Ch2 Control0 Fine Delay……48ps
Ch2 Control1 Fine Delay……48ps
Ch2 Control2 Fine Delay……48ps
Ch2 Control3 Fine Delay……48ps
Ch2 Command Fine Delay……394ps
Ch1Ch2 Common Clock Setting……More Relaxed (provato anche in Auto)
Ch1 RDCAS GNT-Chip Delay……Auto
Ch1 WRCAS GNT-Chip Delay……Auto
Ch1 Command to CS Delay……Auto
Ch2 RDCAS GNT-Chip Delay…Auto
Ch2 WRCAS GNT-Chip Delay……Auto
Ch2 Command to CS Delay……Auto
- Read Delay Phase Adjust (tutti i valori si sono impostati automaticamente)
Ch1 Read Delay Phase (4~0)……7-7-7-7-7
Channel 1 Phase 0 Pull-in……Auto
Channel 1 Phase 1 Pull-in……Auto
Channel 1 Phase 2 Pull-in……Auto
Channel 1 Phase 3 Pull-in……Auto
Ch2 Read Delay Phase (4~0)……7-7-7-7-7
Channel 2 Phase 0 Pull-in……Auto
Channel 2 Phase 1 Pull-in……Auto
Channel 2 Phase 2 Pull-in……Auto
Channel 2 Phase 3 Pull-in……Auto
- Voltage Settings
CPU VID Control……1.16250 V
CPU VID Special Add Limit……Enabled
CPU VID Special Add……Auto
DRAM Voltage Control……2.11V
SB Core/CPU PLL Voltage……1.75V
NB Core Voltage……1.408V
CPU VTT Voltage……1.303V
Vcore Droop Control……Disabled
Clockgen Voltage Control……3.45V
GTL+ Buffers Strength……Strong
CPU GTL 0 REF Volt……0.6700
CPU GTL 1 REF Volt……0.6700
CPU GTL 2 REF Volt……0.6700
CPU GTL 3 REF Volt……0.6700
NB GTL 0 Ref Volt……0.6700
NB GTL 1 Ref Volt……0.6700
FSB Vref……00