nin
30-06-2010, 11:14
Ciao a tutti!
Scusate se rompo con una questione così vetusta..ma mi sono trovato a dover riesumare un vecchio portatile Acer Travelmate 254lmi_dt (serie 250 comunque) per emergenza.
Ho installato sul computer Debian Lenny e come network manager Wicd, trovandomi su Lxde e non volendo portarmi dietro tutte le dipendenze di altri gestori su kde o gnome.
Il problema credo sia il seguente: il portatile ha un pulsante che consente l'accensione della scheda wireless, sotto windows mi è bastato installare i drivers per xp ma su linux non so assolutamente come farlo riconoscere.
Sto ammattendo perchè credo che nonostante i miei sforzi per far riconoscere la scheda al sistema, senza quel passaggio non vado troppo in là..
Il chipset della scheda mini-pci wireless è Intersil Prism 2.5, aggiornato all'ultimo firmware disponibile.
Di seguito l'output di ifconfig ( a seguito del comando ifconfig wlan0 up) :
eth1 Link encap:Ethernet HWaddr 00:0a:e4:4a:02:16
inet addr:192.168.1.4 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::20a:e4ff:fe4a:216/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1147 errors:0 dropped:0 overruns:0 frame:0
TX packets:813 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1522509 (1.4 MiB) TX bytes:67688 (66.1 KiB)
Interrupt:11 Base address:0x3000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:560 (560.0 B) TX bytes:560 (560.0 B)
wifi0 Link encap:UNSPEC HWaddr 00-02-8A-D8-98-D7-65-74-00-00-00-00-00-00-00-00
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:11
wlan0 Link encap:Ethernet HWaddr 00:02:8a:d8:98:d7
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:11
..e quello di iwconfig:
wifi0 IEEE 802.11b ESSID:"Gabriele" Nickname:""
Mode:Managed Frequency:2.467 GHz Access Point: None
Bit Rate:2 Mb/s Sensitivity=1/3
Retry short limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
wlan0 IEEE 802.11b ESSID:"Gabriele" Nickname:""
Mode:Managed Frequency:2.467 GHz Access Point: None
Bit Rate:2 Mb/s Sensitivity=1/3
Retry short limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=0/70 Signal level=-73 dBm Noise level=-73 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Ho seguito questa guida ufficiale: Guida per driver Hotstap (http://wiki.debian.org/hostap), seguendo tutti i passaggi.
Spero di essere stato completo, grazie per l'eventuale aiuto!
:)
Scusate se rompo con una questione così vetusta..ma mi sono trovato a dover riesumare un vecchio portatile Acer Travelmate 254lmi_dt (serie 250 comunque) per emergenza.
Ho installato sul computer Debian Lenny e come network manager Wicd, trovandomi su Lxde e non volendo portarmi dietro tutte le dipendenze di altri gestori su kde o gnome.
Il problema credo sia il seguente: il portatile ha un pulsante che consente l'accensione della scheda wireless, sotto windows mi è bastato installare i drivers per xp ma su linux non so assolutamente come farlo riconoscere.
Sto ammattendo perchè credo che nonostante i miei sforzi per far riconoscere la scheda al sistema, senza quel passaggio non vado troppo in là..
Il chipset della scheda mini-pci wireless è Intersil Prism 2.5, aggiornato all'ultimo firmware disponibile.
Di seguito l'output di ifconfig ( a seguito del comando ifconfig wlan0 up) :
eth1 Link encap:Ethernet HWaddr 00:0a:e4:4a:02:16
inet addr:192.168.1.4 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::20a:e4ff:fe4a:216/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1147 errors:0 dropped:0 overruns:0 frame:0
TX packets:813 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1522509 (1.4 MiB) TX bytes:67688 (66.1 KiB)
Interrupt:11 Base address:0x3000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:560 (560.0 B) TX bytes:560 (560.0 B)
wifi0 Link encap:UNSPEC HWaddr 00-02-8A-D8-98-D7-65-74-00-00-00-00-00-00-00-00
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:11
wlan0 Link encap:Ethernet HWaddr 00:02:8a:d8:98:d7
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:11
..e quello di iwconfig:
wifi0 IEEE 802.11b ESSID:"Gabriele" Nickname:""
Mode:Managed Frequency:2.467 GHz Access Point: None
Bit Rate:2 Mb/s Sensitivity=1/3
Retry short limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
wlan0 IEEE 802.11b ESSID:"Gabriele" Nickname:""
Mode:Managed Frequency:2.467 GHz Access Point: None
Bit Rate:2 Mb/s Sensitivity=1/3
Retry short limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=0/70 Signal level=-73 dBm Noise level=-73 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Ho seguito questa guida ufficiale: Guida per driver Hotstap (http://wiki.debian.org/hostap), seguendo tutti i passaggi.
Spero di essere stato completo, grazie per l'eventuale aiuto!
:)