[lcapriotti]

Originariamente inviato da avware

E' proprio arrivato a questo punto che deve iniziare lo studio invece

allora ho riconfigurato in annex B (ma devo anche mettere su un firmware diverso?) e corretto il refuso, ora la config e':

config interface 'loopback'
        option ifname 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'

config globals 'globals'
        option ula_prefix 'fd99:14c7:13ee::/48'

config dsl 'dsl'
        option annex 'b'
        option tone 'av'
        option xfer_mode 'ptm'
        option firmware '/lib/firmware/lantiq-vrx200-a.bin'

config interface 'lan'
        option type 'bridge'
        option ifname 'eth0.1'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'
        option ip6assign '60'

config interface 'wan'
        option proto 'pppoa'
        option encaps 'vc'
        option atmdev '0'
        option vci '101'
        option vpi '0'
        option ipv6 'auto'

config device 'wan_dev'
        option name 'ptm0'
        option macaddr '44:E9:DD:7C:C4:00'

config interface 'wan6'
        option proto 'dhcpv6'
        option reqaddress 'try'
        option reqprefix 'auto'
        option ifname 'nas0'

config switch
        option name 'switch0'
        option reset '1'
        option enable_vlan '1'

config switch_vlan
        option device 'switch0'
        option vlan '1'
        option ports '0 2 4 5 6t'

config atm-bridge
        option unit '0'
        option atmdev '0'
        option encaps 'vc'
        option vci '101'
        option vpi '0'
        option payload 'bridged'

e lo status rende:

root@lede:~# /etc/init.d/dsl_control status
ATU-C Vendor ID:                          Broadcom 176.200
ATU-C System Vendor ID:                   Broadcom
Chipset:                                  Lantiq-VRX200 Unknown
Firmware Version:                         5.8.1.8.1.6
API Version:                              4.17.18.6
XTSE Capabilities:                        0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x2
Annex:                                    B
Line Mode:                                G.993.2 (VDSL2)
Profile:                                  8b
Line State:                               UP [0x801: showtime_tc_sync]
Forward Error Correction Seconds (FECS):  Near: 0 / Far: 3
Errored seconds (ES):                     Near: 0 / Far: 12
Severely Errored Seconds (SES):           Near: 0 / Far: 0
Loss of Signal Seconds (LOSS):            Near: 0 / Far: 0
Unavailable Seconds (UAS):                Near: 27 / Far: 27
Header Error Code Errors (HEC):           Near: 0 / Far: 0
Non Pre-emtive CRC errors (CRC_P):        Near: 0 / Far: 0
Pre-emtive CRC errors (CRCP_P):           Near: 0 / Far: 0
Power Management Mode:                    L0 - Synchronized
Latency / Interleave Delay:               Down: Fast (0.14 ms) / Up: Fast (0.0 ms)
Data Rate:                                Down: 14.008 Mb/s / Up: 911 Kb/s
Line Attenuation (LATN):                  Down: 33.5dB / Up: 13.7dB
Signal Attenuation (SATN):                Down: 29.8dB / Up: 13.7dB
Noise Margin (SNR):                       Down: 14.3dB / Up: 16.1dB
Aggregate Transmit Power (ACTATP):        Down: 10.8dB / Up: 18.5dB
Max. Attainable Data Rate (ATTNDR):       Down: 22.418 Mb/s / Up: 2.603 Mb/s
Line Uptime Seconds:                      1413
Line Uptime:                              23m 33s