Con un normale convertitore LVTTL-RS232 (da seriale a 3,3V a seriale standard...) sono riuscito a connettermi al NAS (per il momento in ricezione...)
Su J2 i collegamenti sono i seguenti:
Pin 1 --> GND
Pin 3 --> 3,3V
Pin 4 --> TX NAS
Allego il LOG:
Uncompressing Linux.............................................................
....................... done, booting the kernel.
request_standard_resources()....OK
trap_init().....OK
init_IRQ().....OK
sched_init().....OK
softirq_init().....OK
time_init().....OK
Linux version 2.4.27-star (
[email protected]) (gcc version 3.3.6) #1709
Wed Jul 11 10:54:19 CST 2007
CPU: FA526id(wb) revision 1
ICache:16KB enabled, DCache:16KB enabled, BTB support
Machine: STAR_STR9100
On node 0 totalpages: 8192
zone(0): 8192
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0,38400 root=/dev/ram0 initrd=0x00900000,10M me
m=32M@0x00000000
IRQ Timer1 at interrupt number 0x0 and clock 100000000(Hz)
console_init().....OK
kmem_cache_init().....OK
Calibrating delay loop... 153.60 BogoMIPS
Memory: 32MB = 32MB total
Memory: 19328KB available (1953K code, 575K data, 220K init)
mem_init().....OK
pgtable_cache_init().....OK
max_threads is :512 @@@@@@@@@@@@@@@@@
proc_caches_init().....OK
Dentry cache hash table entries: 4096 (o
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
vfs_caches_init().....OK
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
buffer_init().....OK
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
page_cache_init().....OK
signals_init().....OK
POSIX conformance testing by UNIFIX
Data In reg is:1bf00e!!!!!!!!!!!!!
USB to PC now
PCI: bus0: Fast back to back transfers disabled
pci bridge found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
do initcalls start
Starting kswapd
NTFS driver v1.1.22 [Flags: R/W]
SGI XFS with no debug enabled
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-algo-bit.o: i2c bit algorithm module
pty: 256 Unix98 ptys configured
Str9100 Serial Driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xf7800000 (irq = 10) is a Star_UART
!!!!!!!!!!!!!mac is: 0:16:67:0:8a:3
RAMDISK driver initialized: 16 RAM disks of
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Creating 3 MTD partitions on "str9100_flash":
0x00000000-0x00020000 : "Armboot"
0x00020000-0x007e0000 : "Kernel & Ramdisk"
0x007e0000-0x00800000 : "configure"
ftl_cs: FTL header not found.
ftl_cs: FTL header not found.
ftl_cs: FTL header not found.
usb.c: registered new driver hub
hcd.c: ehci_hcd @ EHCI, EHCI_HCdriver
hcd.c: irq 24, pci mem fcc00000
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
host/usb-ohci.c: USB OHCI at membase 0xc3819000, IRQ 23
host/usb-ohci.c: usb-OHCI, OHCI_HCdriver
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver usblp
printer.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for
NET4: AppleTalk 0.18a for Linux NET4.0
NetWinder Floating Point Emulator V0.97 (double precision)
do initcalls end
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 10240K
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 220K
UART IRQ_ports = c02a6018
UART IRQ at interrupt number 0xa
Mon Jan 1 00:00:00 UTC 2007
Mounting root fs rw ...
hub.c: new USB device EHCI-2, assigned address 2
Load x1205 rtc driver ...
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: MAXTOR S Model: TM3250310AS Rev:
Type: Direct-Access ANSI SCSI revision: 02
Using /lib/modules/2.4.27-star/x1205-rtc.o
X1205: I2C based RTC driver.
X1205: found X1205 on STR9100 I2C Adapter
ccr_write_enable: verify SR failed
X1205: i2c_add_driver RTC driver.
X1205: misc_register RTC driver.
atr is 0
port:50
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Synchronize system date & time .Partition check:
.. sda:
sda1 sda2 sda3
Mounting other filesystems ...
System initialization begin!
Load configuration file OK!
Time zone setting OK!
Load nt_sev OK!
Network setting OK!
System time setting OK!
sh: ¨t@þÿ¿,þÿ¿Àµ: not found
Http & Ftp OK!
Load automount OK!
USB connect to pc;
clear all interrupt !
Load button driver OK!
Adding Swap: 465876k swap-space (priority -1)
Load bittorrent job control deamon OK!
XFS mounting filesystem sd(8,2)
Load upnp av finished!
Starting XFS recovery on filesystem: sd(8,2) (dev: sd(8,2))
Load check disk full finished!
Ending XFS recovery on filesystem: sd(8,2) (dev: sd(8,2))
XFS mounting filesystem sd(8,3)
System initialization end!
Load printerd ...
printerd wakened
Sysinit done
BusyBox v1.00-rc2 (2006.09.14-03:08+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
# Starting XFS recovery on filesystem: sd(8,3) (dev: sd(8,3))
Ending XFS recovery on filesystem: sd(8,3) (dev: sd(8,3))
Saluti!