[Carciofone]

Originariamente inviato da Bovirus

@Carciofone

Prima di provarci sarebbe meglio avere sia il debrick midficato che l'immagine completa del fw funzionante.

Nessuna notiza da wyokterm?

Ho trovato questa: http://www.dd-wrt.com/dd-wrtv2/down....tility_v48.zip
Nel changelog tra i chip supportati c'è anche il 29LV320MB:

The following flash chips (switch options) are supported:

/fc:01 ..... AMD 29lv160DB 1Mx16 BotB (2MB)
/fc:02 ..... AMD 29lv160DT 1Mx16 TopB (2MB)
/fc:03 ..... AMD 29lv320DB 2Mx16 BotB (4MB)
/fc:04 ..... AMD 29lv320DT 2Mx16 TopB (4MB)
/fc:05 ..... AMD 29lv320MB 2Mx16 BotB (4MB)
/fc:06 ..... AMD 29lv320MT 2Mx16 TopB (4MB)
/fc:07 ..... AMD 29lv320MT 2Mx16 TopB (4MB)
/fc:08 ..... Intel 28F128J3 8Mx16 (16MB)
/fc:09 ..... Intel 28F160B3 1Mx16 BotB (2MB)
/fc:10 ..... Intel 28F160B3 1Mx16 TopB (2MB)
/fc:11 ..... Intel 28F160C3 1Mx16 BotB (2MB)
/fc:12 ..... Intel 28F160C3 1Mx16 TopB (2MB)
/fc:13 ..... Intel 28F160S3/5 1Mx16 (2MB)
/fc:14 ..... Intel 28F320B3 2Mx16 BotB (4MB)
/fc:15 ..... Intel 28F320B3 2Mx16 TopB (4MB)
/fc:16 ..... Intel 28F320C3 2Mx16 BotB (4MB)
/fc:17 ..... Intel 28F320C3 2Mx16 TopB (4MB)
/fc:18 ..... Intel 28F320J3 2Mx16 (4MB)
/fc:19 ..... Intel 28F320J5 2Mx16 (4MB)
/fc:20 ..... Intel 28F320S3/5 2Mx16 (4MB)
/fc:21 ..... Intel 28F640B3 4Mx16 BotB (8MB)
/fc:22 ..... Intel 28F640B3 4Mx16 TopB (8MB)
/fc:23 ..... Intel 28F640C3 4Mx16 BotB (8MB)
/fc:24 ..... Intel 28F640C3 4Mx16 TopB (8MB)
/fc:25 ..... Intel 28F640J3 4Mx16 (8MB)
/fc:26 ..... Intel 28F640J5 4Mx16 (8MB)
/fc:27 ..... MBM29LV320BE 2Mx16 BotB (4MB)
/fc:28 ..... MBM29LV320TE 2Mx16 TopB (4MB)
/fc:29 ..... MX29LV320B 2Mx16 BotB (4MB)
/fc:30 ..... MX29LV320B 2Mx16 BotB (4MB)
/fc:31 ..... MX29LV320T 2Mx16 TopB (4MB)
/fc:32 ..... MX29LV320T 2Mx16 TopB (4MB)
/fc:33 ..... SST39VF320 2Mx16 (4MB)
/fc:34 ..... ST 29w320DB 2Mx16 BotB (4MB)
/fc:35 ..... ST 29w320DT 2Mx16 TopB (4MB)
/fc:36 ..... Sharp 28F320BJE 2Mx16 BotB (4MB)
/fc:37 ..... TC58FVB321 2Mx16 BotB (4MB)
/fc:38 ..... TC58FVT321 2Mx16 TopB (4MB)

* If you have trouble with auto-detection or just running the software try using both
the /noreset and /nobreak options together.

* In this version I have gone back to the normal flash window of 0x1FC00000 for the
smaller flash chips (2MB and 4MB), while the larger flash chips (8MB and 16MB) will
use the flash window at 0x1C000000.

* Included are the source files for Compiling under Linux (default), Windows, FreeBSD.
Also included are a pre-compiled version (wrt54g.exe) for Windows, along with the
GiveIO.sys driver and installer which are need ONLY for use with Windows.

* I have also included the original "HairyDairyMaid_WRT54G_v2_DeBrick_Guide.pdf"
for reference in creating the needed JTAG cable and to give some basic
understanding of debricking your router / flashing via EJTAG. Note that
in this version some of the command line switches have changed from what is
represented in the "HairyDairyMaid_WRT54G_v2_DeBrick_Guide.pdf" doc. I am
not going to go back and re-write that doc! (I hate writing documentation)

* Many thanks to Terry Porter for creating an easy to read schematic
(jtag-hairydairymaid.png) that I have also included here for reference
in building the JTAG cable. (As info - it shows GND being connected to
pin 6 on the JTAG header side and the .doc show it going to pin 2 as
either work just the same).

* Thanks to Daniel O'Connor for the FreeBSD support suggestion/code.

Enjoy!

-hairydairydairy (a.k.a lightbulb)