DFI Lanparty UT nF4 SLI-DR Expert
Immagini
Caratteristiche- AMD socket939 Athlon FX55+ & Athlon X2 CPU supported
- Software control SLI switch
- Karajan Audio(Theater like7.1/8ch Audio)
- Dual Gigabit LAN
- Magnetic-levitate fan on chipset heatsink
- 4 x Serial ATA-2(3Gb/s)
- 100% Japanese Capacitors/ 4 phase PWM
- UV sensitive slots
- EZ-on / EZ-touch onboard switch button
- Silicon image3114~RAID5 ready
- nVIDIA nTune(embedded overclocking solution)
- nVIDIA ActiveArmor
(Embedded hardware firewall & network solution) - CMOS reloaded®
- All New Genie BIOS for extreme overclocking!
Specifiche Tecniche
Quote:
CPU
- AMD® Athlon 64 X2 / Athlon 64 FX / Athlon 64 / Sempron
- Socket 939
Chipset
- NVIDIA nForce4 SLI - Supports NVIDIA SLI (Scalable Link Interface)
Front Side Bus
- 2000MT/s HyperTransport interface
Memory
- Four 184-pin DDR SDRAM DIMM sockets
- Supports dual channel (128-bit wide) memory interface
- Supports up to 4GB system memory
- Supports PC2100 (DDR266), PC2700 (DDR333) and PC3200 (DDR400) DDR SDRAM DIMM
SLI / Single VGA Mode
- SLI mode - Use 2 SLI-ready PCI Express x16 graphics cards (use identical cards) on the PCI Express x16 slots. - Each x16 slot operates at x8 bandwidth. When the graphics cards are connected via the SLI bridge, the total bandwidth of the two graphics cards is x16.
- Single VGA mode - 1 PCI Express graphics card on the PCIE1 slot operates at x16 bandwidth. - The other PCI Express x16 slot (PCIE4) operates at x2 bandwidth.
BIOS
- Award BIOS
- CMOS Reloaded
- CPU/DRAM overclocking
- CPU/DRAM/Chipset overvoltage
- 4Mbit flash memory
Power Management
- Supports ACPI STR (Suspend to RAM) function
- Wake-On-Events include: - Wake-On-PS/2 Keyboard/Mouse - Wake-On-USB Keyboard/Mouse - Wake-On-LAN - RTC timer to power-on the system
- AC power failure recovery
Hardware Monitor
- Monitors CPU/system/chipset temperature
- Monitors 12V/5V/3.3V/Vcore/Vbat/5Vsb/Vchipset/Vdram voltages
- Monitors the speed of the CPU fan, Fan 2 and Fan 3 fan
- CPU Overheat Protection function monitors CPU temperature during system boot-up
Audio
- Karajan audio module - Realtek ALC850 8-channel AC’97 audio CODEC - 6 audio jacks - 1 CD-in connector - 1 front audio connector
- True stereo line level outputs
- S/PDIF-in/out interface
LAN
- Dual Gigabit LAN - Vitesse VSC8201 Gigabit Phy and Marvell 88E8001 Gigabit PCI
- Fully compliant to IEEE 802.3 (10BASE-T), 802.3u (100BASE-TX) and 802.3ab (1000BASE-T) standards
IDE
- Supports two IDE connectors that allows connecting up to four UltraDMA 133Mbps hard drives
- NVIDIA RAID allows RAID arrays spanning across Serial ATA and Parallel ATA
- RAID 0, RAID 1, RAID 0+1 and JBOD
Serial ATA with RAID
- Four Serial ATA ports supported by the nForce4 SLI chip - SATA speed up to 3Gb/s - RAID 0, RAID 1, RAID 0+1 and JBOD - NVIDIA RAID allows RAID arrays spanning across Serial ATA and Parallel ATA
- Four Serial ATA ports supported by the Silicon Image Sil 3114 chip - SATA speed up to 1.5Gb/s - RAID 0, RAID 1, RAID 0+1 and RAID 5
IEEE 1394
- VIA VT6307
- Supports two 100/200/400 Mb/sec ports
Rear Panel I/O Ports
- 1 mini-DIN-6 PS/2 mouse port
- 1 mini-DIN-6 PS/2 keyboard port
- 2 S/PDIF RCA jacks (S/PDIF-in and S/PDIF-out)
- Karajan audio module (6 audio jacks)
- 1 IEEE 1394 port
- 2 RJ45 LAN ports
- 6 USB 2.0/1.1 ports
I/O Connectors
- 2 connectors for 4 additional external USB 2.0/1.1 ports
- 1 connector for 1 external IEEE 1394 port
- 1 connector for 1 external serial port
- 1 connector for the Karajan audio module
- 1 front audio connector for external line-out and mic-in jacks (on the Karajan audio module)
- 1 CD-in internal audio connector (on the Karajan audio module)
- 1 S/PDIF connector for optical cable connection
- 1 IrDA connector
- 8 Serial ATA connectors
- 2 IDE connectors
- 1 floppy connector
- 1 24-pin ATX power connector
- 1 8-pin ATX 12V power connector
- 1 4-pin 5V/12V power connector (FDD type)
- 1 front panel connector
- 5 fan connectors
- 4 diagnostic LEDs
- EZ touch switches (power switch and reset switch)
Expansion Slots
- 2 PCI Express x16 slots
- 1 PCI Express x1 slot
- 1 PCI Express x4 slot
- 3 PCI slots
PCB
- ATX form factor
- 24cm (9.45") x 30.5cm (12")
|
Manuali
Differenze con la SLI-DR
Bios
***IMPORTANTE, non flashate i bios di altre Main Lanparty, altrimenti ucciderete le Expert***
E' possibile flashare i bios della Venus (anche se non portano grandi vantaggi) pero su alcune main non è garantito che il flashing vada a buon fine, meglio quindi avere un bios di scorta
Beta- N4ELDB11.zip (2005-11-11 non proveniente dal sito DFI)
- N4ELDB17.zip (2005-11-17)
Codice:
Enhance Memory Support
- N4ELDB22.zip (2005-11-22 non proveniente dal sito DFI)
Codice:
Added Ram DLL (Auto , Low Speed , High Speed)
- N4ELDB25.zip (2005-11-25)
Codice:
Support AMD Athlon 64 FX60 CPU's
- NF4AD329 (2006/03/29)
Codice:
Add CPU temperature calibration option.
Fix S1/S3 temp error after resume.
Fix startup VID option fail.
Fix C 'n' Q .5 multiplier not working with opteron CPU.
Fix day of month alarm can not set as 0 for every day usage.
Fix ATI X1000 series logo error
Ufficiali- NF4EDB02.zip (2005-11-02)
- NF4EDC07.zip (2005/12/07)
Codice:
Enhance Memory Support.
Support AMD Athlon 64 FX60 CPUs.
Add over clocks step by step.
- NF4ED406.zip (2006/04/06)
Codice:
Remove Write CAS latency item and replace it by Odd Divisor Select.
Add support for SST 49LF040B LPC flash ROM.
Add CPU temperature calibration option.
Fix s1/s3 temp error after resume.
Fix startup vid option fail.
Fix c'n'q .5 multiplier not working with opteron cpu.
Fix day of month alarm can not set as 0 for every day usage.
Fix ATI X1000 series logo error.
Modded- 704-2 - By BigToe
Codice:
basato sugli stessi tweak per le altre LP nF4
- 406 - By BigToe
Codice:
Basato sul 3/29 Beta
Added "odd divisor correct" option and removed Write Cas latency(set at 1 now)
Added Vdimm on VE and EX over4V (for extreme clocking)
Added chipset voltage 2V on VE and EX (for extreme clocking)
Relaxed memory timings, set 2t at boot to make the board more boot friendly
Utility per il flash
Guide al Flash del Bios
Drivers
AC'97 Audio CODECs (per tutti i sistemi Windows dal 98 in poi)
NVIDIA- nForce4 series - Windows 2000/XP - 6.86
Codice:
* Driver audio (v4.65) "WHQL"
* Utilità audio (v4.51)
* Driver Ethernet (v50.25) "WHQL"
* Network Management Tools (v50.19)
* Driver SMBus (v4.57) "WHQL"
* Programma di installazione (v4.89)
* Driver WinXP IDE SataRAID (v6.66) "WHQL"
* Driver WinXP IDE SataIDE (v6.66) "WHQL"
* WinXP RAIDTOOL (v6.63)
- nForce4 series - Windows XP Professional x64 - 6.86
Codice:
* Driver audio (v4.65) "WHQL"
* Utilità audio (v4.51)
* Driver Ethernet (v50.25) "WHQL"
* Network Management Tools (v50.19)
* Driver SMBus (v4.57) "WHQL"
* Programma di installazione (v4.89)
* Driver WinXP IDE SataRAID (v6.66) "WHQL"
* Driver WinXP IDE SataIDE (v6.66) "WHQL"
* WinXP RAIDTOOL (v6.63)
Silicon Image 3114
Marvell
Utility varie
Tips & Tricks
E caldamente consigliato mettere le ram negli slot arancioni (come scritto anche nel manuale) e di mettere il modulo ram con piu propensione all'overclock nello slot piu vicino al socket.
Timings consigliati coi TCCX (by BigToe)
Codice:
LDT Voltage Control........................... - 1.30v
Chip Set Voltage Control...................... - 1.68v
DRAM Voltage Control.......................... - 2.71v
DRAM Configuration Settings:
DRAM Frequency Set............................ - 200=RAM/FSB:01/01
Command Per Clock (CPC)....................... - Enable
CAS Latency Control (Tcl)..................... - 2.5
RAS# to CAS# delay (Trcd)..................... - 4.0
Min RAS# active time (Tras)................... - 10.0
Row precharge time (Trp)...................... - 4.0
Row Cycle time (Trc).......................... - 10 Bus Clocks
Row refresh cyc time (Trfc)................... - 24 Bus Clocks
Row to Row delay (Trrd)....................... - 03 Bus Clocks
Write recovery time (Twr)..................... - 02 Bus Clocks
Write to Read delay (Twtr).................... - 02 Bus Clocks
Read to Write delay (Trwt).................... - 02 Bus Clocks
Refresh Period (Tref)......................... - 3072 Cycles
DRAM Bank Interleave.......................... - Enabled
DQS Skew Control.............................. - Auto
DQS Skew Value................................ - 0
RAM DLL SPEED................................. - High Speed
DRAM Drive Strength........................... - Level 5
DRAM Data Drive Strength...................... - Level 1
Max Async Latency............................. - 7.0ns
DRAM Response Time............................ - Normal
Read Preamble Time............................ - 5.5ns
IdleCycle Limit............................... - 128 Cycles
Dynamic Counter............................... - Disable
R/W Queue Bypass.............................. - 16 x
Bypass Max.................................... - 04 x
32 Byte Granularity........................... - Disable(4 Bursts)
Questi invece sono i timings con cui attualmente mi trovo meglio io coi TCCD
Codice:
LDT Voltage Control........................... - 1.30v
Chip Set Voltage Control...................... - 1.68v
DRAM Voltage Control.......................... - 2.84v
DRAM Configuration Settings:
DRAM Frequency Set............................ - 200=RAM/FSB:01/01
Command Per Clock (CPC)....................... - Enable
CAS Latency Control (Tcl)..................... - 2.5
RAS# to CAS# delay (Trcd)..................... - 3.0
Min RAS# active time (Tras)................... - 7.0
Row precharge time (Trp)...................... - 3.0
Row Cycle time (Trc).......................... - 10 Bus Clocks
Row refresh cyc time (Trfc)................... - 17 Bus Clocks
Row to Row delay (Trrd)....................... - 03 Bus Clocks
Write recovery time (Twr)..................... - 02 Bus Clocks
Write to Read delay (Twtr).................... - 02 Bus Clocks
Read to Write delay (Trwt).................... - 02 Bus Clocks
Refresh Period (Tref)......................... - 3072 Cycles
DRAM Bank Interleave.......................... - Enabled
DQS Skew Control.............................. - Auto
DQS Skew Value................................ - 0
DRAM Drive Strength........................... - Level 7
DRAM Data Drive Strength...................... - Level 2
Max Async Latency............................. - 8.0ns
DRAM Response Time............................ - Normal
Read Preamble Time............................ - 6.0ns
IdleCycle Limit............................... - 128 Cycles
Dynamic Counter............................... - Disable
R/W Queue Bypass.............................. - 16 x
Bypass Max.................................... - 07 x
32 Byte Granularity........................... - Disable(4 Bursts)
Timings consigliati con i chipset UCCC (by BigToe)
Codice:
LDT Voltage Control........................... - 1.30v
Chip Set Voltage Control...................... - 1.68v
DRAM Voltage Control.......................... - 2.71v
DRAM Configuration Settings:
DRAM Frequency Set............................ - 200=RAM/FSB:01/01
Command Per Clock (CPC)....................... - Enable
CAS Latency Control (Tcl)..................... - 3.0
RAS# to CAS# delay (Trcd)..................... - 4.0
Min RAS# active time (Tras)................... - 10.0
Row precharge time (Trp)...................... - 4.0
Row Cycle time (Trc).......................... - 10 Bus Clocks
Row refresh cyc time (Trfc)................... - 24 Bus Clocks
Row to Row delay (Trrd)....................... - 03 Bus Clocks
Write recovery time (Twr)..................... - 02 Bus Clocks
Write to Read delay (Twtr).................... - 02 Bus Clocks
Read to Write delay (Trwt).................... - 02 Bus Clocks
Refresh Period (Tref)......................... - 3072 Cycles
DRAM Bank Interleave.......................... - Enabled
DQS Skew Control.............................. - Auto
DQS Skew Value................................ - 0
RAM DLL SPEED................................. - High Speed
DRAM Drive Strength........................... - Level 8
DRAM Data Drive Strength...................... - Level 1
Max Async Latency............................. - 7.0ns
DRAM Response Time............................ - Normal
Read Preamble Time............................ - 5.5ns
IdleCycle Limit............................... - 128 Cycles
Dynamic Counter............................... - Disable
R/W Queue Bypass.............................. - 16 x
Bypass Max.................................... - 04 x
32 Byte Granularity........................... - Disable(4 Bursts)
Timings consigliati con i chipset UTT (by BigToe)
Codice:
LDT Voltage Control........................... - 1.30v
Chip Set Voltage Control...................... - 1.68v
DRAM Voltage Control.......................... - 3.22v
DRAM Configuration Settings:
DRAM Frequency Set............................ - 200=RAM/FSB:01/01
Command Per Clock (CPC)....................... - Enable
CAS Latency Control (Tcl)..................... - 2.0
RAS# to CAS# delay (Trcd)..................... - 2.0
Min RAS# active time (Tras)................... - 8.0
Row precharge time (Trp)...................... - 2.0
Row Cycle time (Trc).......................... - 10 Bus Clocks
Row refresh cyc time (Trfc)................... - 24 Bus Clocks
Row to Row delay (Trrd)....................... - 03 Bus Clocks
Write recovery time (Twr)..................... - 02 Bus Clocks
Write to Read delay (Twtr).................... - 01 Bus Clocks
Read to Write delay (Trwt).................... - 02 Bus Clocks
Refresh Period (Tref)......................... - 3072 Cycles
DRAM Bank Interleave.......................... - Enabled
DQS Skew Control.............................. - Auto
DQS Skew Value................................ - 0
RAM DLL SPEED................................. - High Speed
DRAM Drive Strength........................... - Level 8
DRAM Data Drive Strength...................... - Level 1
Max Async Latency............................. - 7.0ns
DRAM Response Time............................ - Normal
Read Preamble Time............................ - 5.5ns
IdleCycle Limit............................... - 128 Cycles
Dynamic Counter............................... - Disable
R/W Queue Bypass.............................. - 16 x
Bypass Max.................................... - 04 x
32 Byte Granularity........................... - Disable(4 Bursts)
Timings consigliati con ram OCZ (vedere in basso i modelli) --->segnalate da
bartolino3200 
Codice:
LDT Voltage Control........................... - 1.30v
Chip Set Voltage Control...................... - 1.52v
DRAM Voltage Control.......................... - 2.71v
DRAM Configuration Settings:
DRAM Frequency Set............................ - 200=RAM/FSB:01/01
Command Per Clock (CPC)....................... - Enable
CAS Latency Control (Tcl)..................... - 3.0
RAS# to CAS# delay (Trcd)..................... - 4.0
Min RAS# active time (Tras)................... - 8.0
Row precharge time (Trp)...................... - 3.0
Row Cycle time (Trc).......................... - 11 Bus Clocks
Row refresh cyc time (Trfc)................... - 16 Bus Clocks
Row to Row delay (Trrd)....................... - 03 Bus Clocks
Write recovery time (Twr)..................... - 03 Bus Clocks
Write to Read delay (Twtr).................... - 02 Bus Clocks
Read to Write delay (Trwt).................... - 03 Bus Clocks
Refresh Period (Tref)......................... - 3120 Cycles
DRAM Bank Interleave.......................... - Enabled
DQS Skew Control.............................. - Auto
DQS Skew Value................................ - 0
RAM DLL SPEED................................. - High Speed
DRAM Drive Strength........................... - Level 07
DRAM Data Drive Strength...................... - Level 2
Max Async Latency............................. - 8.0ns
DRAM Response Time............................ - Normal
Read Preamble Time............................ - 6.0ns
IdleCycle Limit............................... - 128 Cycles
Dynamic Counter............................... - Disable
R/W Queue Bypass.............................. - 16 x
Bypass Max.................................... - 04 x
32 Byte Granularity........................... - Disable(4 Bursts)
Lista Ram OCZ- PC3200 Platinum and Titanium 2GB Kit Part Number: OCZ4002048ELDCPE-K, OCZP4002GK, and OCZ4002048ELDCTE-K
- PC3200 Platinum Rev 2 1GB Kit Part Number: OCZ4001024ELDCPER2-K
- PC4000 Platinum EB 2GB Kit Part Number: OCZ5002048EBPE-K
- PC3200 Gold and Gold XTC 1GB KitPart Number: OCZ4001024ELDCGE-K and OCZ4001024ELGEGXT-K
- PC4000 Gold and Gold XTC 2GB Part Number: OCZ5002048ELGE-K and OCZ5002048ELGEGXT-K
- PC3500 Gold Gamer's Xtreme and Xtreme XTC 1GB Part Number: OCZ4331024ELDCGE-K and OCZ4331024ELGEGXT-K
- PC3200 Gold XTC 2GB Part Number: OCZ4002048ELGEGXT-K
- PC3200 Value 2GB Part Number: OCZ4002048V3DC-K
- PC4000 Gold VX Part Number: OCZ5001024ELDCGEVX-K
- PC4000 Platinum XTC Part Number: OCZP5002GXTC-K
- PC3200 Gold C2 1GB Kit Part Number: OCZ4001024ELDCGEC2-K
- 4800Plats (elite) DDR600 run 1GB (2x512) D/C Kit PN – OCZ6001024EEPE-K
Qui la discussione uffficiale sul forum OCZ
Tabella dei voltaggi erogabili alla cpu (by
ixtapalapaquetl)
Procedura consigliata per abilitare lo SLI:- Mettere le due schede
- Impostare nel bios 8-4-NB-8
- Installare Windows ex novo
- Installare i Driver della main e della vga
- Riavviare il pc e spegnerlo
- Inserire il bridge SLi nelle due schede
- Riaccendere il pc
Bug Noti- La mainboard non gradisce molto le ram con chipset Samsung (sopratutto i TCCD e TCC5, ma anche gli UCCC non sembrano volare), sono caldamente consigliati i chipset BH-5/UTT
- La temperatura indicata sulla Cpu è di circa 6-7° piu bassa di quella reale (problema risolvibile con i bios successivi al beta 2006/03/29)
- Il programma Speedfan risulata incompatibile fino alla versione 4.30 con la nostra main (causa freeze e riavii), i problemi sembrano risolti dalla versione 4.31 in poi.
Revision
Attualmente in giro sembrano esserci tre revision di questa mainboard, la AA0, la AB0 e la A02, quest'ultima pare essere quella con meno problemi.