Entra

View Full Version : bios portatili.


orlando_b
22-03-2005, 20:36
come mai il bios dei portatili è così scarno?? ci sono opzioni nascoste?

Arajein
22-03-2005, 22:35
bella domanda, l'ho notato anche io,,, su su, avanti con le risposte! :D :D

samuele1234
22-03-2005, 23:01
Dipende da marca a marca.
Per esempio i bios della compaq (quelli che ho visto io) non ti fanno impostare niente, mentre altri ti fanno impostare qualcosa (comunque di solito hanno molte meno opzioni di quelle di una scheda madre di un fisso).
Penso che questo sia dovuto al fatto che il notebook lo compri già bello e pronto, e la possibilità di upgrade è molto limitata, e oltretutto meno opzioni ci sono, minore è la probabilità che un utente inesperto vada a fare dei macelli.

darp
22-03-2005, 23:13
Be su un portatile con un centrino non avrebbe molto senso ad esempio il settaggio delle frequenze o le impostazioni di controllo energetico modificabili, a mio parere.

Symonjfox
23-03-2005, 10:47
Il modo migliore se effettivamente è disponibile un BIOS completo, è quello di verificare nel sito della motherboard (non quello della marca del portatile).

Con CPU-Z andate su Motherboard e cercate con Google il modello esatto. Se avete fortuna, trovate il sito e il BIOS completo per il vostro portatile.

ATTENZIONE! Se sbagliate qualcosa, il portatile non partirà più!!!!!

PS: ho letto di gente che è riuscita in questo tipo di operazione e un bios più completo, a mio avviso è utilissimo.

Il portatile di mia sorella, ad esempio, ha il chipset Via KT400A con un Athlon XP M 2600+, con il bus impostato a 266Mhz, ma con RAM a 333 Mhz. Col bios normale non si può fare niente, ma con un bios giusto, capite anche voi che imposterei FSB a 333, in sincrono con le RAM, aumentando le prestazioni senza per forza overcloccare.

kirk96
23-03-2005, 14:55
Originariamente inviato da Symonjfox
ATTENZIONE! Se sbagliate qualcosa, il portatile non partirà più!!!!!

scusa, potresti essere un po' più dettagliato su questo aspetto?
Saluti

Kirk :)

Symonjfox
23-03-2005, 18:00
Originariamente inviato da kirk96
scusa, potresti essere un po' più dettagliato su questo aspetto?
Saluti

Kirk :)
Beh, più dettagliato. Cioè, mai flashato un bios? Se salta la corrente, se il Bios non è quello esatto per il modello preciso, se avvengono strani avvenimenti imprevisti durante il flash, ecc ecc. l'apparecchio che stavi aggiornando puoi anche salutarlo (oppure devi trovare qualcuno bravo bravo che riesce a flasharlo a caldo (cosa non facile)).

Per esempio io ho rovinato un lettore DVD da tavolo (aggiornando il firmware da CD-RW invece che da CD-R come consigliato. Infatti quel CD-RW era di qualità scadente. A metà aggiornamento esce la scritta ERROR e da allora non è più funzionato).
Un altro caso è stato un masterizzatore DVD Samsung, dove probabilmente era errato il BIOS e, al termine, masterizzava, ma i DVD uscenti erano perfettamente ILLEGGIBILI.

Cioè, flashare i BIOS e i Firmware è un'operazione molto rischiosa. Bisogna essere sicuri al 100% di cosa si stia facendo.

Per questo ho detto di fare attenzione. Cioè, se per ipotesi trovi il BIOS nuovo per la tua motherboard, ma per qualche losco motivo poi non era quello esatto, potrebbe succedere che non riparta più (mentre in altri casi più fortunati, il programma che flasha avverte che i BIOS sono per hardware diverso).

kirk96
23-03-2005, 18:23
Grazie Simon! :D :D

Symonjfox
23-03-2005, 19:04
Originariamente inviato da kirk96
Grazie Simon! :D :D
Di nulla ;)

mpec82
24-03-2005, 09:20
Io ho unfujitsu-siemens amilo a7600, cpu-z mi dice che la mainboard è una ati raptor. Ho fatto una ricerca ma nn ho trovato niente.

Il bios è un PhoenixBIOS 4.0 Release 6.0 del 09/12/02. Ha senso aggiornarlo? Finora non ho mai avuto problemi. Inoltre alla luce delle vostre informazioni, mi sta passando la voglia (paura). La vostra opinione? :)

Symonjfox
24-03-2005, 12:47
http://download.fujitsu-siemens.com/DriverCD/Start_GB_Notebook.htm

Intanto, suppongo tu abbia già guardato questa pagina. Il sito ufficiale Fujitsu Siemens. Ho trovato il tuo bios, scarica l'immagine CD e masterizzala. Occhio a non usare CDRW rovinati o di bassa qualità, perchè altrimenti ti si può bloccare a metà il flash (a me è capitato una volta con un lettore DVD da tavolo).

*********************************************
* *
* BIOS Flash-update for Fujitsu Siemens *
* AMILO AMILO A-6600, A-7600 *
* BFY26011001, BFY26011002 *
* *
*********************************************


After running ACY6V110.EXE the floppy disk should contain following files:


Flash.bat
Readme.txt (this file)
bios.wph
PHLASH16.EXE


To flash your BIOS.
Please boot in DOS-mode from the floppy disk created and type FLASH.

!! Connect AC adapter before flashing !!
Important Note: !Please reboot your system after flashing!


current BIOS V1.10:

Problems solved:

- Fixed serial port commulication lose data.
- Fixed USB 2.0 pcmcia card performance problem.

Known errors, problems and restrictions:

- If customer upgrades from bios version 1.06 or older the HDD will be locked if the HDD
password is enabled. Solution: Disable HDD password before flashing.
- Wakeup by scheduler from S4 state does not work.
- Flashing from BIOS 1.05 to any older version freezes the system after completion.
The user must first remove all power (AC-plug and battery), after this it is possible to
use the system with the flashed BIOS version.

Additional information:

- If the HDD get locked during bios upgrade the customer can set any passwords to get access
to the HDD. There is no need to use a master password.
- Systems which are delivered without internal floppy disk drive can boot from USB floppy disk.
- The USB floppy disk drive will become the first boot device when it is connected.
- It is mandatory to use this BIOS version with the new CPUs (2400+ and higher with 512KB
2nd Level Cache).

.............................................................................................

predecessor V1.09

Problems solved:

- A LAN boot issue was solved.

Known errors, problems and restrictions:

- If customer upgrades from bios version 1.06 or older the HDD will be locked if the HDD
password is enabled. Solution: Disable HDD password before flashing.
- Wakeup by scheduler from S4 state does not work.
- Flashing from BIOS 1.05 to any older version freezes the system after completion.
The user must first remove all power (AC-plug and battery), after this it is possible to
use the system with the flashed BIOS version.

Additional information:

- If the HDD get locked during bios upgrade the customer can set any passwords to get access
to the HDD. There is no need to use a master password.
- Systems which are delivered without internal floppy disk drive can boot from USB floppy disk.
- The USB floppy disk drive will become the first boot device when it is connected.
- It is mandatory to use this BIOS version with the new CPUs (2400+ and higher with 512KB
2nd Level Cache).

.............................................................................................

predecessor V1.08

Problems solved:

- The reason for this BIOS Version is related to the additional information.

Known errors, problems and restrictions:

- Wakeup by scheduler from S4 state does not work.
- Flashing from BIOS 1.05 to any older version freezes the system after completion.
The user must first remove all power (AC-plug and battery), after this it is possible to
use the system with the flashed BIOS version.

Additional information:

- Systems which are delivered without internal floppy disk drive can boot from USB floppy disk.
- The USB floppy disk drive will become the first boot device when it is connected.
- It is mandatory to use this BIOS version with the new CPUs (2400+ and higher with 512KB
2nd Level Cache).

.............................................................................................

predecessor V1.07

Problems solved:

- External PS/2 keyboard now works properly.
- Solves the problem, that existed where the BIOS default values were loaded and passwords cleared
after S4 with following reboot.

Known errors, problems and restrictions:

- Wakeup by scheduler from S4 state does not work.
- Flashing from BIOS 1.05 to any older version freezes the system after completion.
The user must first remove all power (AC-plug and battery), after this it is possible to
use the system with the flashed BIOS version.

Additional information:

- It is mandatory to use this BIOS version with the new CPUs (2400+ and higher with 512KB
2nd Level Cache).

.............................................................................................

predecessor V1.06


Solved problems:

- BIOS will not auto-reboot when flash-process has terminated.

Known errors, problems and restrictions:

- The right ALT and CTRL key on an external PS2 keyboard do not work
- Wakeup by scheduler from S4 state does not work.
- Flashing from 1.05 to any older version freezes the system after flashing.
The user has to remove AC-plug and battery. After that he can use the system with the flashed
BIOS version.


Additional information:

- Update for correct support of 2000+ and 2200+ CPUs

.............................................................................................

predecessor V1.05

Solved problems:

- BIOS cannot be flashed without AC-adapter plugged in

Known errors, problems and restrictions:

- This BIOS will not auto-reboot when flash-process has terminated.
- Wakeup by scheduler from S4 does not work.
- Flashing from 1.05 to any older version freezes the system after flashing.
The user has to remove AC-plug and battery. After that he can use the system with the flashed
BIOS version

Additional information:

- This BIOS was only for production line.


.............................................................................................

predecessor V1.04

Solved problems:

- CMOS data won’t get lost anymore.
- Video memory (UMA size) is automatically allocated according to the amount of
populated memory.
- PS/2-wheelmice cannot be used after S3-resume.
- Support for B0-stepping CPUs added.
- Support for AMD 2200+ CPUs added.
- VGA BIOS update for LG 15” panel.

Known errors, problems and restrictions:

- This BIOS will not auto-reboot when flash-process has terminated.

Additional information:

- none

.............................................................................................

predecessor V1.03

Solved problems:

- Functionality added: It is now possible to simulate brightness and display hotbuttons
on external PS/2-keybaords. On external PS/2-keyboards press left CTRL and left ALT
keys simultaneously to simulate “Fn”-key on notebook keyboard. CTRL-ALT-F5 is display switch,
CTRL-ALT-Cursor up/down is brightness increase/decrease.
Note: this function is working with PS/2-keyboards only – USB-keyboards are not supported!
- Starting/rebooting the notebook will disable the “PadLock” function. Since there is no LED
indicator for this function the users could have experienced trouble with password entries.

Known errors, problems and restrictions:

- none

Additional information:

- PS/2-wheelmice cannot be used after S3-resume. Workaround until next BIOS: use S4 (hibernate) instead.


.............................................................................................

Predecessor BIOS V 1.02

Solved problems:

- Change boot device priority to: ODD - FDD – HDD
- The following CPU’s are supported:
- Mobile AMD Athlon 1400+
- Mobile AMD Athlon 2000+

Known errors, problems and restrictions:

- none

Additional information:

- It is mandatory to use this BIOS after an update or exchange of the CPU or mainboard.


.............................................................................................

Predecessor BIOS V 1.01

this is an initial BIOS
Cmq se dici che tutto funziona bene e non dà problemi, allora forse è meglio non rischiare, giusto?