il lettore viene correttamente riconosciuto fra le periferiche usb (usb 2)
Riporto un po' più delle ultime 20 righe
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
Probing IDE interface ide1...
hdc: LITE-ON DVD SOHD-167T, ATAPI CD/DVD-ROM drive
hdd: HL-DT-ST DVDRAM GSA-4120B, ATAPI CD/DVD-ROM drive
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 48X DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
ide-floppy driver 0.99.newide
ACPI: PCI interrupt 0000:06:01.0[A] -> GSI 22 (level, low) -> IRQ 22
ahc_pci:6:1:0: Host Adapter Bios disabled. Using default SCSI device parameters
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2902/04/10/15/20C/30C SCSI adapter>
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
PCI: Enabling device 0000:06:01.0 (0116 -> 0117)
ACPI: PCI interrupt 0000:06:01.0[A] -> GSI 22 (level, low) -> IRQ 22
PCI: Unable to reserve mem region #2:1000@dfeff000 for device 0000:06:01.0
aic7xxx: <Adaptec AIC-7850 SCSI host adapter> at PCI 6/1/0
aic7xxx: I/O ports already in use, ignoring.
libata version 1.02 loaded.
ata_piix version 1.02
ACPI: PCI interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ata: 0x170 IDE port busy
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xFFA0 irq 14
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
ata1: dev 1 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f
ata1: dev 1 ATA, max UDMA/133, 312581808 sectors: lba48
ata1: dev 0 configured for UDMA/133
ata1: dev 1 configured for UDMA/133
scsi1 : ata_piix
Vendor: ATA Model: ST3160021AS Rev: 3.05
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: ST3160021AS Rev: 3.05
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3
Attached scsi disk sdb at scsi1, channel 0, id 1, lun 0
Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0, type 0
Attached scsi generic sg1 at scsi1, channel 0, id 1, lun 0, type 0
ohci1394: $Rev: 1223 $ Ben Collins <
[email protected]>
ACPI: PCI interrupt 0000:06:05.0[A] -> GSI 17 (level, low) -> IRQ 17
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17] MMIO=[dfefd000-dfefd7ff] Max
Packet=[2048]
video1394: Installed video1394 module
ieee1394: raw1394: /dev/raw1394 device initialized
sbp2: $Rev: 1219 $ Ben Collins <
[email protected]>
ieee1394: Loaded AMDTP driver
ieee1394: Loaded CMP driver
pd: pd version 1.05, major 45, cluster 64, nice 0
pda: Autoprobe failed
pd: no valid drive found
pcd: pcd version 1.07, major 46, nice 0
pcd0: Autoprobe failed
pcd: No CD-ROM drive found
pg: pg version 1.02, major 97
pga: Autoprobe failed
pg: No ATAPI device detected
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI
Controller
ieee1394: Host added: ID:BUS[0-00:1023] GUID[001111000027042a]
ehci_hcd 0000:00:1d.7: BIOS handoff failed (104, 1010001)
ehci_hcd 0000:00:1d.7: continuing after BIOS bug...
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 23, pci mem f883ec00
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI
#1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 23, io base 0000e000
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI
#2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 19, io base 0000e400
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI
#3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 18, io base 0000e800
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI
#4
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: irq 16, io base 0000ec00
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usbcore: registered new driver usblcd
drivers/usb/misc/usblcd.c: USBLCD Driver Version 1.04 (C) Adams IT Services http
://www.usblcd.de
drivers/usb/misc/usblcd.c: USBLCD support registered.
usbcore: registered new driver usbled
usbcore: registered new driver usbtest
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
input: PC Speaker
Bluetooth: HCI USB driver ver 2.7
usbcore: registered new driver hci_usb
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 15
p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
ACPI: (supports S0 S1 S3 S4 S5)
ACPI wakeup devices:
PEGP P0P2 AC97 USB0 USB1 USB2 USB3 USB7 UAR1 PEX1 PEX2 PEX3 PEX4 AZAL PWRB
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 268k freed
usb 1-4: new high speed USB device using address 2
uba: resid 0 len 18 act 0
uba: resid 0 len 18 act 0
uba: device 2 capacity nsec 50 bsize 512
uba: resid 0 len 18 act 0
uba: made changed
uba: resid 0 len 18 act 0
uba: device 2 capacity nsec 50 bsize 512
uba: resid 0 len 18 act 0
uba: device 2 capacity nsec 50 bsize 512
uba:end_request: I/O error, dev uba, sector 0
Buffer I/O error on device uba, logical block 0
end_request: I/O error, dev uba, sector 2
Buffer I/O error on device uba, logical block 1
end_request: I/O error, dev uba, sector 4
Buffer I/O error on device uba, logical block 2
end_request: I/O error, dev uba, sector 6
Buffer I/O error on device uba, logical block 3
end_request: I/O error, dev uba, sector 6
Buffer I/O error on device uba, logical block 3
end_request: I/O error, dev uba, sector 4
Buffer I/O error on device uba, logical block 2
end_request: I/O error, dev uba, sector 2
Buffer I/O error on device uba, logical block 1
end_request: I/O error, dev uba, sector 0
Buffer I/O error on device uba, logical block 0
ldm_validate_partition_table(): Disk read failed.
end_request: I/O error, dev uba, sector 2
Buffer I/O error on device uba, logical block 1
end_request: I/O error, dev uba, sector 4
Buffer I/O error on device uba, logical block 2
end_request: I/O error, dev uba, sector 6
Buffer I/O error on device uba, logical block 3
end_request: I/O error, dev uba, sector 0
Buffer I/O error on device uba, logical block 0
unable to read partition table
uba:end_request: I/O error, dev uba, sector 2
Buffer I/O error on device uba, logical block 1
end_request: I/O error, dev uba, sector 4
Buffer I/O error on device uba, logical block 2
end_request: I/O error, dev uba, sector 6
Buffer I/O error on device uba, logical block 3
end_request: I/O error, dev uba, sector 0
Buffer I/O error on device uba, logical block 0
ldm_validate_partition_table(): Disk read failed.
end_request: I/O error, dev uba, sector 2
Buffer I/O error on device uba, logical block 1
end_request: I/O error, dev uba, sector 4
Buffer I/O error on device uba, logical block 2
end_request: I/O error, dev uba, sector 6
Buffer I/O error on device uba, logical block 3
end_request: I/O error, dev uba, sector 0
Buffer I/O error on device uba, logical block 0
unable to read partition table
usb 5-1: new low speed USB device using address 2
input,hiddev96: USB HID v1.10 Keyboard [13ec:0006] on usb-0000:00:1d.3-1
EXT3 FS on sda2, internal journal
Adding 1028152k swap on /dev/sda3. Priority:1 extents:1
EXT3 FS on sda2, internal journal
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sda1.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sda1.
NTFS volume version 3.1.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sdb2.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sdb2.
NTFS volume version 3.1.
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1: LSR safety check engaged!
ttyS1: LSR safety check engaged!
NET: Registered protocol family 17
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (8177 buckets, 65416 max) - 304 bytes per conntrack
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sda1.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sda1.
NTFS volume version 3.1.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sdb2.
FAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev sdb2.
NTFS volume version 3.1.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0504580(lo)
IPv6 over IPv4 tunneling driver
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
ttyS1: LSR safety check engaged!
Bluetooth: L2CAP ver 2.4
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.3
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
mtrr: 0xb0000000,0x10000000 overlaps existing 0xb0000000,0x200000
drivers/usb/input/hid-input.c: event field not found
eth0: no IPv6 routers present
ABORTED IN=ppp0 OUT= MAC= SRC=80.183.42.251 DST=80.183.125.220 LEN=40 TOS=0x00 PREC=0x00 TTL=122 ID=46806 PROTO=TCP SPT=3999 DPT=445 SEQ=44644491 ACK=44644491 WINDOW=0 RES=0x00 RST URGP=0
ABORTED IN=ppp0 OUT= MAC= SRC=80.183.42.251 DST=80.183.125.220 LEN=40 TOS=0x00 PREC=0x00 TTL=122 ID=47026 PROTO=TCP SPT=3999 DPT=445 SEQ=44644491 ACK=44644491 WINDOW=0 RES=0x00 RST URGP=0