supermarchino
28-06-2004, 12:15
si blocca sempre al 73%!!! :mad: :mad:
View Full Version : [mdk 10] da fat32 a fat32: impossibile copiare un file di 1,3Gb!!
lovaz
28-06-2004, 12:17
Che ti dà
ulimit -f
?
ulimit -f
?
supermarchino
28-06-2004, 12:19
Originariamente inviato da lovaz
Che ti dà
ulimit -f
?
unlimited
Che ti dà
ulimit -f
?
unlimited
lovaz
28-06-2004, 12:22
E se provi a copiare in un'altra part (magari ext3) e poi sull'altra fat?
supermarchino
28-06-2004, 12:23
Originariamente inviato da lovaz
E se provi a copiare in un'altra part (magari ext3) e poi sull'altra fat?
posso provare, mi si piantava da fat32 a fat32 e da fat32 a smb
cmq. indica chiaramente che è un problema di LETTURA
E se provi a copiare in un'altra part (magari ext3) e poi sull'altra fat?
posso provare, mi si piantava da fat32 a fat32 e da fat32 a smb
cmq. indica chiaramente che è un problema di LETTURA
supermarchino
28-06-2004, 12:24
ALL.TO
supermarchino
28-06-2004, 12:33
Originariamente inviato da lovaz
E se provi a copiare in un'altra part (magari ext3) e poi sull'altra fat?
idem si pianta al 73%
è un po' frustrante 'sta situazione :rolleyes:
E se provi a copiare in un'altra part (magari ext3) e poi sull'altra fat?
idem si pianta al 73%
è un po' frustrante 'sta situazione :rolleyes:
lovaz
28-06-2004, 12:33
Usa cp, magari è konqueror che ha problemi...
supermarchino
28-06-2004, 12:36
Originariamente inviato da lovaz
Usa cp, magari è konqueror che ha problemi...
proverò con cp, ma ho i miei dubbi, visto che con nautilus è la stessa storia.... :rolleyes: :rolleyes:
Usa cp, magari è konqueror che ha problemi...
proverò con cp, ma ho i miei dubbi, visto che con nautilus è la stessa storia.... :rolleyes: :rolleyes:
supermarchino
28-06-2004, 12:46
cp: lettura di `/mnt/documenti/bakmdk.tib': Input/output error
lovaz
28-06-2004, 12:51
Non sarà qualche cluster difettoso? Scandisk?
supermarchino
28-06-2004, 12:55
Originariamente inviato da lovaz
Non sarà qualche cluster difettoso? Scandisk?
neppure winzoz copia: dice 'controllo di ridondanza ciclico'
eppure con chkdsk /f non rileva problemi...
:rolleyes: :rolleyes: :rolleyes:
Non sarà qualche cluster difettoso? Scandisk?
neppure winzoz copia: dice 'controllo di ridondanza ciclico'
eppure con chkdsk /f non rileva problemi...
:rolleyes: :rolleyes: :rolleyes:
Paolo-82
28-06-2004, 14:59
Ma la fat32 non aveva dei limiti alla grandezza massima per i file? Non è che magari li hai superati...
supermarchino
28-06-2004, 15:04
Originariamente inviato da Paolo-82
Ma la fat32 non aveva dei limiti alla grandezza massima per i file? Non è che magari li hai superati...
il limite è 4 gb
Ma la fat32 non aveva dei limiti alla grandezza massima per i file? Non è che magari li hai superati...
il limite è 4 gb
lovaz
30-06-2004, 09:27
Originariamente inviato da supermarchino
neppure winzoz copia: dice 'controllo di ridondanza ciclico'
eppure con chkdsk /f non rileva problemi...
:rolleyes: :rolleyes: :rolleyes:
A questo punto penso sia un problema di disco, che dice smart?
http://sourceforge.net/projects/smartmontools/
Se l'hai gia' installato:
smartctl -a /dev/hdX
(devi mettere il device del disco)
neppure winzoz copia: dice 'controllo di ridondanza ciclico'
eppure con chkdsk /f non rileva problemi...
:rolleyes: :rolleyes: :rolleyes:
A questo punto penso sia un problema di disco, che dice smart?
http://sourceforge.net/projects/smartmontools/
Se l'hai gia' installato:
smartctl -a /dev/hdX
(devi mettere il device del disco)
ilsensine
30-06-2004, 09:42
Originariamente inviato da supermarchino
neppure winzoz copia: dice 'controllo di ridondanza ciclico'
eppure con chkdsk /f non rileva problemi...
CRC error...male.
Rifai la copia con linux, quando arriva all'errore controlla i messaggi del kernel (dmesg). Anzi meglio, scrivili su un file (dmesg > file.txt) e allegalo. Ho paura che ci troviamo una sorpresina.
neppure winzoz copia: dice 'controllo di ridondanza ciclico'
eppure con chkdsk /f non rileva problemi...
CRC error...male.
Rifai la copia con linux, quando arriva all'errore controlla i messaggi del kernel (dmesg). Anzi meglio, scrivili su un file (dmesg > file.txt) e allegalo. Ho paura che ci troviamo una sorpresina.
supermarchino
30-06-2004, 12:54
Originariamente inviato da ilsensine
CRC error...male.
Rifai la copia con linux, quando arriva all'errore controlla i messaggi del kernel (dmesg). Anzi meglio, scrivili su un file (dmesg > file.txt) e allegalo. Ho paura che ci troviamo una sorpresina.
sorpresina? :rolleyes:
(maxtor)
CRC error...male.
Rifai la copia con linux, quando arriva all'errore controlla i messaggi del kernel (dmesg). Anzi meglio, scrivili su un file (dmesg > file.txt) e allegalo. Ho paura che ci troviamo una sorpresina.
sorpresina? :rolleyes:
(maxtor)
supermarchino
30-06-2004, 14:54
Originariamente inviato da lovaz
A questo punto penso sia un problema di disco, che dice smart?
http://sourceforge.net/projects/smartmontools/
Se l'hai gia' installato:
smartctl -a /dev/hdX
(devi mettere il device del disco)
thanx
questo il risultato :confused:
smartctl version 5.31 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: Maxtor 6Y080L0
Serial Number: Y2FXW95E
Firmware Version: YAR41BW0
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Wed Jun 30 15:51:50 2004 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 241) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 37) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 225 225 063 Pre-fail Always - 6259
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 53
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 7
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 252 249 187 Pre-fail Always - 44338
9 Power_On_Minutes 0x0032 253 253 000 Old_age Always - 36h+34m
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 253 253 000 Old_age Always - 57
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always - 27
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 1196
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 1
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 2
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0
209 Offline_Seek_Performnce 0x0024 192 192 000 Old_age Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 740 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 740 occurred at disk power-on lifetime: 29 hours (1 days + 5 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 77 0c 2e e6 Error: UNC 1 sectors at LBA = 0x062e0c77 = 103681143
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 77 0c 2e e6 00 01:20:04.784 READ DMA
ca 00 08 3f 98 b0 e1 00 01:20:04.784 WRITE DMA
ca 00 08 07 7d 4f e0 00 01:20:04.784 WRITE DMA
ca 00 08 cf 00 00 e0 00 01:20:04.784 WRITE DMA
c8 00 80 ef 0d 2e e6 00 01:20:04.784 READ DMA
Error 739 occurred at disk power-on lifetime: 29 hours (1 days + 5 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 77 0c 2e e6 Error: UNC 1 sectors at LBA = 0x062e0c77 = 103681143
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 77 0c 2e e6 00 01:20:03.744 READ DMA
ca 00 08 3f 98 b0 e1 00 01:20:03.728 WRITE DMA
ca 00 08 df 00 00 e0 00 01:20:03.728 WRITE DMA
c8 00 01 00 00 00 e0 00 01:20:03.728 READ DMA
c8 00 80 6f 0d 2e e6 00 01:20:03.712 READ DMA
Error 738 occurred at disk power-on lifetime: 29 hours (1 days + 5 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 77 0c 2e e6 Error: UNC 1 sectors at LBA = 0x062e0c77 = 103681143
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 77 0c 2e e6 00 01:20:02.672 READ DMA
ca 00 08 3f 98 b0 e1 00 01:20:02.672 WRITE DMA
ca 00 08 1f 7d 4f e0 00 01:20:02.672 WRITE DMA
ca 00 10 57 99 01 e0 00 01:20:02.672 WRITE DMA
c8 00 01 00 00 00 e0 00 01:20:02.656 READ DMA
Error 737 occurred at disk power-on lifetime: 29 hours (1 days + 5 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 77 0c 2e e6 Error: UNC 1 sectors at LBA = 0x062e0c77 = 103681143
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 77 0c 2e e6 00 01:20:01.632 READ DMA
c8 00 70 7f 0c 2e e6 00 01:20:01.632 READ DMA
c8 00 08 6f 0c 2e e6 00 01:20:01.616 READ DMA
ca 00 08 3f 98 b0 e1 00 01:20:01.584 WRITE DMA
c8 00 78 77 0c 2e e6 00 01:18:55.040 READ DMA
Error 736 occurred at disk power-on lifetime: 29 hours (1 days + 5 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 71 77 0c 2e e6 Error: UNC 113 sectors at LBA = 0x062e0c77 = 103681143
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 78 77 0c 2e e6 00 01:18:55.040 READ DMA
c8 00 80 6f 0c 2e e6 00 01:18:54.032 READ DMA
c8 00 80 ef 0b 2e e6 00 01:18:54.032 READ DMA
c8 00 80 6f 0b 2e e6 00 01:18:54.032 READ DMA
c8 00 80 ef 0a 2e e6 00 01:18:54.032 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
A questo punto penso sia un problema di disco, che dice smart?
http://sourceforge.net/projects/smartmontools/
Se l'hai gia' installato:
smartctl -a /dev/hdX
(devi mettere il device del disco)
thanx
questo il risultato :confused:
smartctl version 5.31 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: Maxtor 6Y080L0
Serial Number: Y2FXW95E
Firmware Version: YAR41BW0
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Wed Jun 30 15:51:50 2004 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 241) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 37) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 225 225 063 Pre-fail Always - 6259
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 53
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 7
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 252 249 187 Pre-fail Always - 44338
9 Power_On_Minutes 0x0032 253 253 000 Old_age Always - 36h+34m
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 253 253 000 Old_age Always - 57
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always - 27
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 1196
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 1
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 2
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0
209 Offline_Seek_Performnce 0x0024 192 192 000 Old_age Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 740 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 740 occurred at disk power-on lifetime: 29 hours (1 days + 5 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 77 0c 2e e6 Error: UNC 1 sectors at LBA = 0x062e0c77 = 103681143
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 77 0c 2e e6 00 01:20:04.784 READ DMA
ca 00 08 3f 98 b0 e1 00 01:20:04.784 WRITE DMA
ca 00 08 07 7d 4f e0 00 01:20:04.784 WRITE DMA
ca 00 08 cf 00 00 e0 00 01:20:04.784 WRITE DMA
c8 00 80 ef 0d 2e e6 00 01:20:04.784 READ DMA
Error 739 occurred at disk power-on lifetime: 29 hours (1 days + 5 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 77 0c 2e e6 Error: UNC 1 sectors at LBA = 0x062e0c77 = 103681143
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 77 0c 2e e6 00 01:20:03.744 READ DMA
ca 00 08 3f 98 b0 e1 00 01:20:03.728 WRITE DMA
ca 00 08 df 00 00 e0 00 01:20:03.728 WRITE DMA
c8 00 01 00 00 00 e0 00 01:20:03.728 READ DMA
c8 00 80 6f 0d 2e e6 00 01:20:03.712 READ DMA
Error 738 occurred at disk power-on lifetime: 29 hours (1 days + 5 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 77 0c 2e e6 Error: UNC 1 sectors at LBA = 0x062e0c77 = 103681143
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 77 0c 2e e6 00 01:20:02.672 READ DMA
ca 00 08 3f 98 b0 e1 00 01:20:02.672 WRITE DMA
ca 00 08 1f 7d 4f e0 00 01:20:02.672 WRITE DMA
ca 00 10 57 99 01 e0 00 01:20:02.672 WRITE DMA
c8 00 01 00 00 00 e0 00 01:20:02.656 READ DMA
Error 737 occurred at disk power-on lifetime: 29 hours (1 days + 5 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 77 0c 2e e6 Error: UNC 1 sectors at LBA = 0x062e0c77 = 103681143
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 77 0c 2e e6 00 01:20:01.632 READ DMA
c8 00 70 7f 0c 2e e6 00 01:20:01.632 READ DMA
c8 00 08 6f 0c 2e e6 00 01:20:01.616 READ DMA
ca 00 08 3f 98 b0 e1 00 01:20:01.584 WRITE DMA
c8 00 78 77 0c 2e e6 00 01:18:55.040 READ DMA
Error 736 occurred at disk power-on lifetime: 29 hours (1 days + 5 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 71 77 0c 2e e6 Error: UNC 113 sectors at LBA = 0x062e0c77 = 103681143
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 78 77 0c 2e e6 00 01:18:55.040 READ DMA
c8 00 80 6f 0c 2e e6 00 01:18:54.032 READ DMA
c8 00 80 ef 0b 2e e6 00 01:18:54.032 READ DMA
c8 00 80 6f 0b 2e e6 00 01:18:54.032 READ DMA
c8 00 80 ef 0a 2e e6 00 01:18:54.032 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
GhePeU
30-06-2004, 19:25
io farei un salto a comprare un hard disk nuovo
e penserei anche a un backup generale il prima possibile
e penserei anche a un backup generale il prima possibile
supermarchino
30-06-2004, 23:23
Originariamente inviato da GhePeU
io farei un salto a comprare un hard disk nuovo
e penserei anche a un backup generale il prima possibile
:eek: :eek:
cmq. il backup è fatto.. soprattutto della preziosa installazione di lin. che il suo tempo lo vuole!
:rolleyes:
sicuro?
ecco i blocchi strani del pc :rolleyes:
io farei un salto a comprare un hard disk nuovo
e penserei anche a un backup generale il prima possibile
:eek: :eek:
cmq. il backup è fatto.. soprattutto della preziosa installazione di lin. che il suo tempo lo vuole!
:rolleyes:
sicuro?
ecco i blocchi strani del pc :rolleyes:
lovaz
02-07-2004, 10:17
Il disco e' in garanzia? Se si' fai un salto sul sito maxtor per vedere la procedura rma
supermarchino
02-07-2004, 18:40
Originariamente inviato da lovaz
Il disco e' in garanzia? Se si' fai un salto sul sito maxtor per vedere la procedura rma
l'hd è dentro a un pc hp non l'ho assemblato io
scusa ma i dati dello smart sono così tragici?
Il disco e' in garanzia? Se si' fai un salto sul sito maxtor per vedere la procedura rma
l'hd è dentro a un pc hp non l'ho assemblato io
scusa ma i dati dello smart sono così tragici?
AnonimoVeneziano
02-07-2004, 19:07
Error 738 occurred at disk power-on lifetime: 29 hours (1 days + 5 hours)
When the command that caused the error occurred, the device was in an unknown state.
738 errori :p
When the command that caused the error occurred, the device was in an unknown state.
738 errori :p
supermarchino
02-07-2004, 20:32
Originariamente inviato da AnonimoVeneziano
738 errori :p
:sofico:
:(
738 errori :p
:sofico:
:(
lovaz
03-07-2004, 12:33
Originariamente inviato da AnonimoVeneziano
738 errori :p
In realtà è un "errore 738" :D
Comunque se lo smart rileva errori di solito vuol dire che il disco fra un po' peggiorerà e fra un altro po' ti lascerà definitivamente :O
Ma il problema qual è? Se il pc è in garanzia fattelo cambiare, altrimenti metti in conto di prendere un altro hd
738 errori :p
In realtà è un "errore 738" :D
Comunque se lo smart rileva errori di solito vuol dire che il disco fra un po' peggiorerà e fra un altro po' ti lascerà definitivamente :O
Ma il problema qual è? Se il pc è in garanzia fattelo cambiare, altrimenti metti in conto di prendere un altro hd
AnonimoVeneziano
08-07-2004, 01:38
Muahahhaah , che pirla che sono :sofico:
ilsensine
08-07-2004, 08:10
Originariamente inviato da lovaz
In realtà è un "errore 738" :D
Hai ragione, gli errori in effetti sono 740 :sofico:
ATA Error Count: 740 (device log contains only the most recent five errors)
In realtà è un "errore 738" :D
Hai ragione, gli errori in effetti sono 740 :sofico:
ATA Error Count: 740 (device log contains only the most recent five errors)
supermarchino
08-07-2004, 08:44
voi ridete io intanto ho fatto una maialata che non posso raccontare e questo ora è il mio smart
smartctl version 5.31 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: Maxtor 6Y080L0
Serial Number: Y2G89NTE
Firmware Version: YAR41BW0
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Thu Jul 8 09:42:11 2004 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 241) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 37) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 225 225 063 Pre-fail Always - 9992
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 86
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 252 248 187 Pre-fail Always - 59847
9 Power_On_Minutes 0x0032 253 253 000 Old_age Always - 105h+14m
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 253 253 000 Old_age Always - 90
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always - 29
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 581
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 1
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0
209 Offline_Seek_Performnce 0x0024 191 191 000 Old_age Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
chiudete che è meglio :oink:
grazie a tutti per l'aiuto!;)
smartctl version 5.31 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: Maxtor 6Y080L0
Serial Number: Y2G89NTE
Firmware Version: YAR41BW0
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Thu Jul 8 09:42:11 2004 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 241) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 37) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 225 225 063 Pre-fail Always - 9992
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 86
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 252 248 187 Pre-fail Always - 59847
9 Power_On_Minutes 0x0032 253 253 000 Old_age Always - 105h+14m
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 253 253 000 Old_age Always - 90
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always - 29
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 581
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 1
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0
209 Offline_Seek_Performnce 0x0024 191 191 000 Old_age Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
chiudete che è meglio :oink:
grazie a tutti per l'aiuto!;)
ilsensine
08-07-2004, 08:47
Serial Number: Y2FXW95E
Serial Number: Y2G89NTE
AL LADROOOOOO!!!! :D
Serial Number: Y2G89NTE
AL LADROOOOOO!!!! :D
supermarchino
08-07-2004, 08:50
Originariamente inviato da ilsensine
AL LADROOOOOO!!!! :D
no, è un nuovo software della maxtor per il teletrasporto dei numeri seriali, risolve anche i guasti :O
:sofico: :sofico:
AL LADROOOOOO!!!! :D
no, è un nuovo software della maxtor per il teletrasporto dei numeri seriali, risolve anche i guasti :O
:sofico: :sofico:
vBulletin® v3.6.4, Copyright ©2000-2025, Jelsoft Enterprises Ltd.