Mimmothor
11-11-2003, 16:51
Ciao ti basta il manuale?
Anch'io ho il T3100 ma ho il floppy rotto!!
Ti è possibile inviarmi il boot ?
Grazie
MODEL:T3100E
1.1 GENERAL
Toshiba Personal Computer T3100e is a compact and lightweight
portable personal computer. The T3100e is a high-performance system
with special features. The CPU is the 80286-12 16-bit microprocessor.
The standard memory has a capacity of 1 Mbyte. The hard disk drive
(HDD) has a capacity of 20 Mbytes. The floppy disk drive (FDD) can
support 2DD (720 Kbytes) and 2HD (1.44 Mbytes) floppy disks. The
universal auto-sensing power supply is used for world-wide usage.
The T3100e system unit consists of the following functional modules;
System board/Memory board
3.5-inch floppy disk drive
3.5-inch hard disk drive
Plasma display
Keyboard
Power supply unit
Figure 1-1 T3100e personal computer
~~
MODEL:T3100E
Page 1-2
1.2 SYSTEM UNIT
The configuration of the system unit is shown in figure 1-2.
Figure 1-2 System unit configuration
Page 1-3
The key features of the system unit are:
o A system board and memory board connected by 2 flat cables.
o An internal 3.5-inch FDD supporting two media types:
2HD (double-side, high-density, double-track)
2DD (double-side, double-density, double-track)
The 2HD and 2DD floppy disks can be formatted with 1.44 Mbytes
and 720 Kbytes of storage capacity, respectively.
o A 20-Mbyte 3.5-inch HDD (hard disk drive).
o An internal 82-key keyboard. For most applications it can be used
exactly like a standard typewriter keyboard.
o An internal 640 x 400 pixel plasma display.
o A universal auto-sensing power supply that can be used
world-wide provides +5 VDC, +12 VDC, -5 VDC and -12 VDC power to
all the components in the system unit, including the option cards.
For the plasma display, the power supply provides the regulated
+205 and +5 VDC power. The power supply's ventilation fans are
driven by +12 VDC.
o A lithium battery that keeps the date and time even when the
system unit power is off.
o A parallel printer (or floppy disk drive), Red/Green/Blue (RGB)
direct drive Cathode Ray Tube (CRT) display, and two SERIAL device
connectors, located on the system unit's rear panel and right
side. The parallel printer connector can be used to connect an
external FDD unit by changing the A-B-PRT switch.
~~
MODEL:T3100E
Page 1-4
1.3 SYSTEM BOARD
Figure 1-3 shows the block diagram of the system board.
Figure 1-3 Block diagram
Page 1-5
System board and memory board are composed of the following components:
System board
o Central processing unit: CPU (80286-12)
The CPU is a 16-bit microprocessor operated at 12 MHz clock speed.
o Numeric data processor socket for the 80287-12 (optional).
o Real time clock: RTC (MC146818)
The RTC continuously keeps the date and time powered by lithium
battery.
o Serial input output: SIO (TC8570)
The SIO controls the RS232C port.
o Variable frequency oscillator: VFO (MB4108A)
The VFO chip is used for FDD control logic.
o Two super integration: SI (JC810, M5M82C800)
SI (JC810) includes the FDC (TC8565), SIO (TC8570), and PIT
(82C54). SI (M5M82C800) includes the two DMACs (82C37), two PICs
(82C59) and one PIT (82C54).
o Gate arrays:
The following gate arrays are used in the system board.
See the T3100e GATE ARRAY SPECIFICATION MANUAL for more
information.
o DMA controller gate array : DMA3-GA (100 pin)
o MAP controller gate array : MAP3-GA (100 pin)
o Bus controller gate array : BUS-GA (100 pin)
o PLC controller gate array : PLC-GA (100 pin)
Page 1-6
Memory board
o Keyboard controller: KBC (8742 or 8042)
o Memory
Random access memory : RAM 1 Mbyte
Read only memory : ROM 64 Kbytes (system BIOS)
o Gate array
The following gate array is used in the memory board.
See the T3100e GATE ARRAY SPECIFICATION MANUAL for more
information.
EMS controller gate array : EMS2-GA (100 pin)
~~
MODEL:T3100E
Page 1-7
1.4 3.5-INCH FLOPPY DISK DRIVE
The 3.5-inch internal FDD is a high performance, reliable and thin
drive that supports 720-Kbyte (formatted) 2DD and 1.44-Mbyte
(formatted) 2HD 3.5-inch floppy disks.
The FDD is shown in figure 1-5 and its specifications are described in
table 1-1.
Figure 1-4 3.5-inch FDD
Table 1-1 3.5-inch FDD specifications
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Item ³ Specifications ³
³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ 2-Mbyte mode ³ 1-Mbyte mode ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Storage Capacity (Kbytes) ³ ³ ³
³ Unformatted ³ 2,000 ³ 1,000 ³
³ Formatted ³ 1,440 ³ 720 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ No. of Heads ³ 2 ³ 2 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ No. of Cylinders ³ 80 ³ 80 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Access Time (ms) ³ ³ ³
³ 1 Track Access ³ 3 ³ 3 ³
³ Average ³ 94 ³ 94 ³
³ Head Settling Time ³ 15 ³ 15 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Recording Density ³ 17434 ³ 8717 ³
³ (bit per inch) (MAX) ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Data Transfer Rate ³ 500 ³ 250 ³
³ (Kbytes per second) ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Rotational Speed ³ 300 ³ 300 ³
³ (revolutions per minute) ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Recording Method ³ MFM (Modified Frequency ³
³ ³ Modulation ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100E
Page 1-8
1.5 3.5-INCH HARD DISK DRIVE
The 20-Mbyte (formatted) HDD is a random access type storage device. It
is equipped with non-removable 3.5-inch magnetic disks and
mini-winchester type magnetic heads. The HDD has three jumper straps
which are located on the hard disk controller (HDC) board.
The HDD is shown in figure 1-5 and its specifications are described in
table 1-2. The jumper straps status are shown in table 1-3.
Figure 1-5 3.5-inch HDD
Page 1-9
Table 1-2 3.5-inch HDD specifications
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Item ³ Specifications ³
³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ ³ 20-Mbyte ³ 40-Mbyte ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Storage Capacity : ³ ³ ³
³ Formatted (Mbytes) ³ 21.4 ³ 42.8 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Number of Disks ³ 1 ³ 1 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Data Surfaces ³ 2 ³ 2 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Data Heads ³ 2 ³ 2 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Tracks per Surface ³ 636 ³ 1,047 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Track Density (tpi) ³ 1,150 ³ 1,400 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Track Capacity : ³ ³ ³
³ Formatted (bytes) ³ 16,896 ³ 20,480 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Sectors per Track : (bps) ³ ³ ³
³ Physical Sectors ³ 34 ³ 41 ³
³ User Sectors ³ 33 ³ 40 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Access Time (ms) ³ ³ ³
³ Track to Track ³ 8 ³ 8 ³
³ Average ³ 27 ³ 25 ³
³ Maximum ³ 50 ³ 50 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Rotation Speed (rpm) ³ 3,575 ³ 3,557 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Data Transfer Rate : (bps) ³ ³ ³
³ To/From Media ³ 1.25 M ³ 1.5 M ³
³ To/From Buffer ³ 4 M ³ 4.5 M ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Start Time (s) ³ ³ ³
³ (0-3575RPM) : Typical ³ 5 ³ 5 ³
³ Maximum ³ 10 ³ 10 ³
³ (0 RPM-READY): Typical ³ 7 ³ 7 ³
³ Maximum ³ 15 ³ 15 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Stop Time (s) : Typical ³ 5 ³ 5 ³
³ Maximum ³ 10 ³ 10 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Interleave ³ CP3022 3 : 1 ³ 1 : 1 ³
³ ³ CP3024 1 : 1 ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Recording Method ³ 2-7 RLL code ³
³ ³ (Run Length Limited) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Recording Density (ID) (bpi) ³ 21,594 ³ 30,871 ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Table 1-3 HDD jumper strap status
20-Mbyte (CP3022)
ÚÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Signal ³ Status ³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄij
³ E5 ³ Short ³
³ E6 ³ Open ³
³ E7 ³ Short ³
ÀÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÙ
20-Mbyte (CP3024) or 40-Mbyte
ÚÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Signal ³ Status ³
ÃÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ HSP ³ Open ³
³ C/D ³ Short ³
³ DHP ³ Open ³
³ ACT ³ Short ³
ÀÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100E
Page 1-10
1.6 KEYBOARD
The 82-key keyboard is mounted on the system unit. The 82 keys consist
of 54 standard keys, 10 function keys, 17 control keys, and Fn key.
The keyboard is a key matrix with one of the 82 keys at each vertex.
The keyboard is connected to the keyboard controller on the memory
board through a 22-pin flat cable. The keyboard layout is shown in
figure 1-6.
Figure 1-6 Keyboard
~~
MODEL:T3100E
Page 1-11
1.7 PLASMA DISPLAY
The plasma display is composed of a display panel and driver circuits.
It receives vertical and horizontal synchronizing signals, four bit
data signals, and shift clock for data transmission. All signals are
TTL level compatible. The specifications are described in table 1-4.
The plasma display is shown in figure 1-7.
Figure 1-7 Plasma display
Table 1-4 Plasma display specifications
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Item ³ Specifications ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ No. of Dots (dots) ³ 640 x400 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Dot Dimension (mm) ³ 0.16 (W) x 0.24 (H) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Dot Pitch (mm) ³ 0.33 (W) x 0.36 (H) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Display Area (mm) ³ 192 (W) x 144 (H) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Contrast ³ more than 1:11 (approx. 1:13) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Color ³ Neon-Orange ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Power Requirement ³ ³
³ Anode Logic (E1) ³ 5 +/-0.5 V ³
³ ³ 10 mA (min.) 400 mA (max.) ³
³ Cathode Driver (E2) ³ 205 +/-5 V ³
³ ³ 3 mA (min.) 160 mA (max.) ³
³ Cathode Logic (E3) ³ 5 +/-0.5 V ³
³ ³ 1 mA (min.) 60 mA (max.) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Power Consumption ³ ³
³ (watts) ³ 35 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Mean Time Between ³ ³
³ Failure (MTBF) ³ ³
³ (hours) ³ 30,000 ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100E
Page 1-12
1.8 POWER SUPPLY UNIT
The universal auto-sensing power supply can be used world-wide and
supplies +5, -5, +12, -12 and +205 VDC to the system.
The power supply unit is housed in the system unit and it supplies the
regulated power to:
1) System board
2) Memory board
3) 3.5-inch floppy disk drive
4) 3.5-inch hard disk drive
5) Plasma display
6) Option boards
7) Cooling fans
The above 2) through 4), 6) and one of cooling fans receive the power
via the system board.
The power supply unit includes an input line filter, line fuse, cooling
fan, power conversion circuitry and connectors.
Input ratings are:
85 to 138 VAC or 170 to 276 VAC, less than 130 W (when input rating is
115 VAC, 60 Hz).
The power supply unit is shown in figure 1-8 and the output ratings are
specified in table 1-5.
Figure 1-8 Power supply unit
Page 1-13
Table 1-5 Power supply unit output rating
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Function ³ DC ³ Max. ³ Requration ³
³ ³ voltage ³ current ³ tolerance ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ System Board ³ +5 V ³ 5.6 A ³ +/- 5% ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ System Board & ³ ³ ³ ³
³ Cooling Fan ³ +12 V ³ 1.1 A ³ +/- 5% ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ System Board ³ -5 V ³ 300 mA ³ +/- 5% ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ System Board ³ -12 V ³ 300 mA ³ +/- 5% ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Plasma Display ³ +5 V ³ 60 mA ³ +/- 10% ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄij
³ Plasma Display ³ +205 V ³ 105 mA ³ +/- 5V ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Page 1-14
File No.: 960-010
~~
MODEL:T3100E
Page 2-1
2.1 GENERAL
The problem isolation procedures described in part 2 are used to
isolate defective FRUs (field replaceable units). The FRUs covered are:
1. Power supply unit
2. System board
3. FDD
4. HDD
5. Keyboard
6. Plasma display
Detailed replacement procedures instructions are described in part 4
and test and diagnostics program operations are described in part 3.
The following items are necessary for implementing the problem
isolation procedures.
1. T3100e diagnostics disk
2. Phillips head screwdriver
3. Blade head screwdriver
4. Tweezers
5. 2DD and 2HD formatted work disk (for FDD testing)
6. Cleaning disk kit (for FDD testing)
7. Multimeter
8. Printer port LED
The problem isolation flowchart described in section 2.2 can be used to
determine which isolation procedures are necessary to isolate a T3100e
problem.
~~
MODEL:T3100E
Page 2-1
2.2 PROBLEM ISOLATION FLOWCHART
The flowchart in figure 2-1 is used as a guide for determining which
FRU is defective. Please confirm the followings before performing the
flowchart procedures.
1. No disk is in the FDD.
2. All optional equipments are disconnected.
3. MS-DOS has been installed in drive C before a trouble happens.
Page 2-2
Figure 2-1 Problem Isolation Flowchart
Page 2-3
Figure 2-1 (cont.) Problem isolation flowchart (continued)
1. If an error is detected on the system test, memory test, display
test, or real timer test, perform the system board isolation
procedures in section 2.4.
2. If an error is detected on the hard disk test, perform the HDD
problem isolation procedures in section 2.6.
3. If an error is detected on the keyboard test, perform the keyboard
problem isolation procedures in section 2.7.
4. If an error is detected on the floppy disk test, perform the FDD
problem isolation procedures in section 2.5.
~~
MODEL:T3100E
Page 2-4
2.3 POWER SUPPLY UNIT PROBLEM ISOLATION PROCEDURESÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ WARNING: Dangerous high voltage is supplied to the power ³
³ supply unit. Pay enough attention on handling. It takes a few ³
³ minutes after power off to discharge the electricity. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
This section describes how to determine whether or not the power supply
unit is defective. Start with PROCEDURE 1 and continue with other
procedures as instructed. The procedures described in this section are:
PROCEDURE 1: Power Indicator Check
PROCEDURE 2: Connector Check
PROCEDURE 3: Output Voltage Check
PROCEDURE 4: Power Supply Unit Replacement
Page 2-5
PROCEDURE 1
Power Indicator Check
1. Turn on the power.
2. If the power indicator lights, go to PROCEDURE 3. If the
indicator does not light, check the AC power cord connection.
One end of the AC power cord should be inserted the standard AC
wall outlet and the other end should be connected to the AC IN
jack on the back of the system unit.
If OK, replace the AC power cord.
After replacing the AC power cord, if the indicator lights, the
original cord was probably defective. If the indicator still
doesn't light, go to PROCEDURE 2.
Page 2-6
PROCEDURE 2
Connector Check
1. Turn off the power, then unplug the AC power cord.
2. Remove the top cover. (Refer to section 4.8.)
3. Remove the power supply unit. (Refer to section 4.9.)
4. If the power supply connector (PJ7) on the system board is connected
properly, go to PROCEDURE 3. If it is not connected properly,
reconnect it.
Page 2-7
PROCEDURE 3
Output Voltage Check
1. Plug the AC power cord to the power supply unit, then turn on the
power.
2. Use a multimeter to confirm that the output voltages for the two
power supply connectors conform to the values given in table 2-1.
3. If the voltages are within the range of values given in table 2-1,
the power supply unit is normal, but the system board is probably
defective. Go to the system board isolation procedures in section
2.4.
4. If the voltages are still not within the range of values given
in table 2-1, go to PROCEDURE 4.
Table 2-1 Power supply unit output voltages
ÚÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ ³ Pin number ³ Voltage (Vdc) ³
³ Connector ÃÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄ´
³ ³ +lead ³ -lead ³ Normal ³ Min ³ Max ³
ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´
³ ³ 1 ³ 2,5,6 ³ 12 ³ 11.4 ³ 12.6 ³
³ ÃÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´
³ For ³ 3 ³ 2,5,6 ³ -12 ³ -12.6 ³ -11.4 ³
³ system ÃÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄij
³ board ³ 4 ³ 2,5,6 ³ -5 ³ -5.25 ³ -4.75 ³
³ ÃÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´
³ ³ 8 ³ 2,5,6 ³ 5 ³ 4.75 ³ 5.25 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´
³ For ³ 1 ³ 4 ³ 205 ³ 200 ³ 210 ³
³ plasma ÃÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´
³ display ³ 5 ³ 4 ³ 5 ³ 4.5 ³ 5.5 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´
³ For ³ ³ ³ ³ ³ ³
³ cooling ³ 1 ³ 2 ³ 12 ³ 11.4 ³ 12.6 ³
³ fan ³ ³ ³ ³ ³ ³
ÀÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÙ
Page 2-8
PROCEDURE 4
Power Supply Unit Replacement
1. Turn off the power, then unplug the AC power cord.
2. Replace the power supply unit. (Refer to section 4.9.)
3. If normal operation is restored after replacing the power supply
unit, the original power supply unit was probably defective.
4. If normal operation is not restored, another FRU is probably
defective. The defective unit must be isolated and replaced.
~~
MODEL:T3100E
Page 2-9
2.4 SYSTEM BOARD PROBLEM ISOLATION PROCEDURES
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³CAUTION: Before carrying out any of these procedures, make ³
³sure that the FDD is empty. Performing these procedures ³
³with a floppy disk in the FDD may result in loss of data. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
This section describes how to determine whether or not the
system board is defective. Start with PROCEDURE 1 and
continue with other procedures as instructed. The
procedures described in this section are:
PROCEDURE 1: Message Check
PROCEDURE 2: Printer Port LED Check
PROCEDURE 3: Test Program Execution
PROCEDURE 4: System Board Replacement
Page 2-10
PROCEDURE 1 Message Check
1. Turn on the power.
2. If the system is loaded normally, go to PROCEDURE 3.
3. If the following message is displayed on the screen, press the
F1 key. Execute the setup operation. (See the section 3 for
details.)
*** Error in CMOS. Bad battery ***
Check system. Then, press [F1) key .....
*** Error in CMOS. Bad check sum ***
Check system. Then, press [F1) key .....
*** Error in CMOS. Bad configuration **
Check system. Then, press [F1) key .....
*** Error in CMOS. Bad memory size ***
Check system. Then, press [F1) key .....
*** Error in CMOS. Bad time function **
Check system. Then, press [F1) key .....
4. If the following message is displayed on the screen, turn off the
power. Wait 5 seconds or more, then turn on the power. If the
following message is displayed again, go to HDD isolation procedures
in section 2.6.
Insert system disk in drive
Press any key when ready .....
Page 2-11
5. If the following message is displayed on the screen, the system may
not be set up correctly. Go to the system setup menu and select the
appropriate system configuration. (see the part 3 for details.) If
the following message is displayed again, go to PROCEDURE 5.
Video RAM error
CRTC error
6. If the following message is displayed on the screen, go to
PROCEDURE 4.
CPU flag register error
KBC IBF/OBF error
KBC IBF error
KBC self test error
KBC OBF error
CPU register error
ROM checksum error
PIT channel 2 error
CMOS shutdown byte error
DMA channel 0 error
DMA channel 1 error
DMA page register error
Memory refresh error
1st 64KB memory error
Error interrupt controller 1
Error interrupt controller 2
VRAM error
Memory verify error at X:X found X expanded X
Memory parity error at X:X found X expected X
Error interrupt and stuck NMI
Error interrupts and stuck NMI
Error interrupts and stuck NMI
Error protect mode...
Error sizing expansion memory
Memory verify error at X:X:X found X expected X
Memory verify error at X:X:X found X expected X
Error processor exceptional interrupts...
Refresh timing error
Error encountered initializing hard drive
First 64KB memory error
LIM page register error
7. If none of the above messages are displayed and you have a printer
port LED, go to PROCEDURE 2.
Page 2-12
PROCEDURE 2
Printer Port LED Check
1. Turn off the power.
2. Plug the printer port LED into the PRT/FDD connector on the back of
the unit and set the A-B-PRT switch to PRT position.
3. While watching the printer port LED, turn on the power. The printer
port LED will light when the power switch is turned on.
4. Read the final LED status from left to right as a hexadecimal
value.
5. If the final LED status matches any of the error code values in the
table 2-3, go to PROCEDURE 4.
6. If the final LED status is 33H, go to PROCEDURE 3.
Table 2-2 Printer port LED normal status
ÚÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Status ³ Error message ³
ÃÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ 00H ³ Shutdown process and video initialization ³
³ 01H ³ CPU test 1 ³
³ 02H ³ KBC test 1 ³
³ 03H ³ KBC test 2 ³
³ 04H ³ KBC test 3 ³
³ 05H ³ KBC test 4 ³
³ 06H ³ LSI initialization ³
³ 07H ³ CPU test 2 ³
³ 08H ³ RTC initialization ³
³ 09H ³ ROM checksum test ³
³ 0AH ³ Video initializatiion ³
³ 0BH ³ Reserved ³
³ 0CH ³ Reserved ³
³ 0DH ³ PIT Channel 2 test and initialization ³
³ 0EH ³ Reserved ³
³ 0FH ³ CMOS RAM test ³
³ 10H ³ DMA CHannel 0 test ³
ÀÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Page 2-13
Table 2-2 Printer port LED normal status (continued)
ÚÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Status ³ Message ³
ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ 11H ³ DMA channel 1 test ³
³ 12H ³ DMA page register test ³
³ 13H ³ Memory refresh test ³
³ 14H ³ First 64KB memory test ³
³ 15H ³ Interrupt vector set ³
³ 16H ³ PIC 1 mask register test ³
³ 17H ³ PIC 2 mask register test ³
³ 18H ³ CMOS Battery test ³
³ 19H ³ CMOS chechsum test ³
³ 1AH ³ Reserved ³
³ 1BH ³ Keyboard initialization 1 ³
³ 1CH ³ VRAM test ³
³ 1DH ³ Video I/O initialization ³
³ 1EH ³ System memory size set ³
³ 1FH ³ System memory size check ³
³ 20H ³ System memory and extra memory test ³
³ 21H ³ PIC test ³
³ 22H ³ NMI and parity test ³
³ 23H ³ Interrupt process test ³
³ 24H ³ Protect mode test ³
³ 25H ³ Extended memory size check ³
³ 26H ³ Extended memory test ³
³ 27H ³ Protect mode exception processing test ³
³ 28H ³ Reserved ³
³ 29H ³ CRT type check ³
³ 2AH ³ PIT interrupt check ³
³ 2BH ³ Hardware interrupt vector set ³
³ 2CH ³ Keyboard initialization 2 ³
³ 2DH ³ FDD initialization ³
³ 2EH ³ SIO/Printer initialization ³
³ 2FH ³ HDD initialization ³
³ 30H ³ Option ROM check ³
³ 31H ³ Timer check ³
³ 32H ³ NDP initialization ³
³ 33H ³ Prepare for boot ³
ÀÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Page 2-14
Table 2-3 Printer port LED error status
ÚÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄ¿
³ Status ³ Error message ³ Process ³
ÃÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄ´
³ 81H ³ CPU flag register error ³ halt ³
³ 82H ³ KBC IBF/OBF error ³ halt ³
³ 83H ³ KBC IBF error ³ halt ³
³ 84H ³ KBC self test error ³ halt ³
³ 85H ³ KBC OBF error ³ halt ³
³ 87H ³ CPU register error ³ halt ³
³ 89H ³ ROM checksum error ³ halt ³
³ 8DH ³ PIT channel 2 error ³ halt ³
³ 8FH ³ CMOS shutdown byte error ³ halt ³
³ 90H ³ DMA channel 0 error ³ halt ³
³ 91H ³ DMA channel 1 error ³ halt ³
³ 92H ³ DMA page register error ³ halt ³
³ 93H ³ Memory refresh error ³ halt ³
³ 94H ³ 1st 64KB memory error ³ halt ³
³ 96H ³ Error interrupt controller 1 ³ halt ³
³ 97H ³ Error interrupt controller 2 ³ Continue ³
³ 9CH ³ VRAM error ³ halt ³
³ A0H ³ Memory verify error at X:X ³ ³
³ ³ found X expanded X ³ Continue ³
³ A1H ³ Error interrupt and stuck NMI ³ Continue ³
³ A2H ³ Error interrupts and stuck NMI ³ Continue ³
³ A3H ³ Error interrupts and stuck NMI ³ Continue ³
³ A4H ³ Error protect mode... ³ Continue ³
³ A5H ³ Error sizing expansion memory ³ Continue ³
³ A6H ³ Memory verify error at X:X:X ³ ³
³ ³ found X expected X ³ Continue ³
³ ³ Memory verify error at X:X:X ³ ³
³ ³ found X expected ³ ³
³ A7H ³ Error processor exceptional interrupts... ³ Continue ³
³ AAH ³ Refresh timing error ³ Continue ³
³ AFH ³ Error encountered initializing ³ ³
³ ³ hard drive ³ Continue ³
³ D4H ³ First 64KB memory error ³ halt ³
³ EOH ³ LIM page register error ³ Continue ³
ÀÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÙ
Page 2-15
PROCEDURE 3
Test Program Execution
1. Execute the following tests on the Diagnostic Test Menu. (Refer to
Part 3 Test and Diagnostics.)
1. System test
2. Memory test
3. Keyboard test
4. Display test
5. Floppy disk test
6. Printer test
7. ASYNC test
8. Hard disk test
9. Real timer test
2. If an error is detected during the system test, memory test,
Printer test, ASYNC test, or real timer test, go to PROCEDURE 4.
3. If an error is detected during the floppy disk test, go to FDD
problem isolation procedures in section 2.5.
4. If an error is detected during the hard disk test, go to HDD
problem isolation procedures in section 2.6.
5. If an error is detected during the keyboard test, go to keyboard
problem isolation procedures in section 2.7.
6. If an error is detected during the display test, go to display
problem isolation procedures in section 2.8.
Page 2-16
PROCEDURE 4
System Board Replacement
1. Replace the system board. (Refer to section 4.16.)
2. If normal operation is restored after replacing the system board,
the original system board is probably defective.
3. If normal operation is not restored, another FRU is probably
defective. The defective unit must be isolated by the test and
diagnostics program and replaced.
~~
MODEL:T3100E
Page 2-17
2.5 FLOPPY DISK DRIVE PROBLEM ISOLATION PROCEDURESThis section describes how to determine whether or not the floppy disk
drive is defective. Start with PROCEDURE 1 and continue with other
procedures as instructed. The procedures described in this section are:
PROCEDURE 1: Test and Diagnostics Program
Loading Check
PROCEDURE 2: Message Check
PROCEDURE 3: Head Cleaning
PROCEDURE 4: FDD Test Execution
PROCEDURE 5: FDD Connector Check
PROCEDURE 6: New FDD Connection
Page 2-18
PROCEDURE 1
Test and Diagnostics Program Loading Check
1. Turn off the power.
2. Insert the diagnostics disk into the FDD.
3. Turn on the power.
4. If loading starts normally, go to PROCEDURE 3. (See section 3.2 to
determine if loading has started normally.)
5. If loading has not started normally, go to PROCEDURE 2.
Page 2-19
PROCEDURE 2
Message Check
1. When the power switch is turned on after the diagnostics disk is
inserted into the FDD, message (a), (b), or (c) shown below may
appear.
(a) *** FDD A is not installed ***
(b) Non-System disk or disk error
Replace and press any key when ready
(c) ** FDD load error or Bad system disk **
Insert system disk in drive
Press any key when ready .....
2. If message (a) is displayed, check that the A-B-PRT switch is set
to PRT. If it is not set to PRT, set it to PRT. If it is set to PRT,
go to PROCEDURE 5.
3. If message (b) or (c) is displayed, the contents of the floppy disk
is damaged, or a disk other than the diagnostics disk has been
inserted into the FDD.
Insert a new diagnostics disk into the FDD. If loading completes,
go to PROCEDURE 4. If loading does not complete, go to PROCEDURE 3.
4. If none of the above messages appears, go to PROCEDURE 5.
Page 2-20
PROCEDURE 3
Head Cleaning
1. Turn off the power.
2. Insert the cleaning disk into the FDD.
3. Turn on the power.
4. If normal operation is restored after cleaning the head, go to
PROCEDURE 4.
5. If normal operation is not restored, go to PROCEDURE 5.
Page 2-21
PROCEDURE 4
FDD Test Execution
1. Run the floppy disk test as indicated on the diagnostic test menu.
2. If an error is generated during the floppy disk test, an error code
and status will be displayed. The error codes are described in table
2-4. Go to PROCEDURE 6.
3. If no error is generated, the FDD is normal.
Table 2-4 FDD error code
ÚÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Code ³ Status ³
ÃÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ 01 ³ Bad Command ³
³ 02 ³ Address Mark Not Found ³
³ 03 ³ Write Protected ³
³ 04 ³ Record Not Found ³
³ 06 ³ Media Removed ³
³ 08 ³ DMA Overrun Error ³
³ 09 ³ DMA Boundary Error ³
³ 10 ³ CRC Error ³
³ 20 ³ FDC Error ³
³ 40 ³ Seek Error ³
³ 60 ³ FDD Not Drive ³
³ 80 ³ Time Out Error ³
³ EE ³ Write Buffer Error ³
ÀÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Page 2-22
PROCEDURE 5
FDD Connector Check
1. Turn off the power, then unplug the AC power cord.
2. Remove the top cover. (Refer to section 4.8.)
3. Check that the FDD connection (PJ8) is secure.
4. If the FDD cable is securely connected to the system board, go to
PROCEDURE 6.
5. If the FDD cable is not securely connected to the system board,
secure the connection.
Page 2-23
PROCEDURE 6
New FDD Connection
1. Turn off the power.
2. Remove the FDD. (Refer to section 4.12.)
3. Connect a new FDD to the FDD connector without installing the new
FDD. Then connect all of the FRUs removed during FDD removal to
their corresponding connectors without installing the FRUs.
4. Turn on the power.
5. If normal operation is restored, the original FDD is probably
defective. Reassemble the system.
6. If normal operation is not restored, the system board is probably
defective. Refer to section 2.4.
~~
MODEL:T3100E
Page 2-24
2.6 HARD DISK DRIVE PROBLEM ISOLATION PROCEDURESThis section describes how to determine whether or not the hard disk
drive is defective. Start with PROCEDURE 1 and continue with other
procedures as instructed. The procedures described in this section are:
PROCEDURE 1: HDD Indicator Check
PROCEDURE 2: Message Check
PROCEDURE 3: Format Execution
PROCEDURE 4: Hard Disk Test Execution
PROCEDURE 5: Connector Check
PROCEDURE 6: HDD Jumper Straps Check
PROCEDURE 7: New HDD Connection
Page 2-25
PROCEDURE 1
HDD Indicator Check
1. Turn off the power.
2. If there is a floppy disk in the FDD, take it out.
3. Wait 5 seconds or more after turning off the power, then turn on
the power.
4. If the HDD indicator blinks briefly, then goes out, go to PROCEDURE
2. If the HDD indicator continues blinking, go to PROCEDURE 4.
5. If the HDD indicator does not light at all, go to PROCEDURE 5.
Page 2-26
PROCEDURE 2
Message Check
1. If the operating system is loaded normally, go to PROCEDURE 4.
2. If one of the following message is displayed on the screen, go to
PROCEDURE 3.
** RDD Load error or Bad system disk **
Insert system disk in drive.
Press any key when ready .....
Check system disk in drive
Press any key when ready .....
Page 2-27
PROCEDURE 3
Format Execution
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³CAUTION: The contents of the hard disk will be erased when the ³
³FORMAT command is run. Before running this test, transfer the contents³
³of the hard disk to floppy disks. This can be done with the MS-DOS ³
³BACKUP command. (See the MS-DOS Manual for details.) ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
1. Remove the diagnostics disk from the FDD, then insert the MS-DOS
system disk in.
2. Make partition of the hard disk by entering the FDISK command. (See
the MS-DOS Manual for details.)
3. Format the hard disk by entering the FORMAT command. (See the
MS-DOS Manual for details.) At this time use /S switch to transfer
the system program.
4. If normal operation is restored, the HDD is normal.
5. If normal operation is not restored, go to PROCEDURE 5.
Page 2-28
PROCEDURE 4
Hard Disk Test Execution
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
¿
³CAUTION: The contents of the hard disk will be erased when the
³
³test program is run. Before running this test, transfer the contents
of³
³the hard disk to floppy disks. This can be done with the MS-DOS BACKUP
³
³command. (See the MS-DOS Manual for details.)
³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Ù
1. Insert the diagnostics disk into the FDD and load the test and
diagnostics programs.
2. Run the hard disk test as indicated on the diagnostic test menu.
3. If an error is detected during the hard disk test, an error code
and status will be displayed; go to PROCEDURE 6. The error codes
are described in table 2-5.
4. If no error is generated, the HDD is normal. Enter the MS-DOS FDISK
command to make partition of the hard disk. Then enter the MS-DOS
FORMAT command. (See the MS-DOS Manual for details.)
Table 2-5 HDD error code
ÚÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Code ³ Status ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ 01 ³ Bad command error ³
³ 02 ³ Bad address mark ³
³ 04 ³ Record not found ³
³ 05 ³ HDC not reset ³
³ 07 ³ Drive not initialize ³
³ 09 ³ DMA boundary error ³
³ 0A ³ Bad sector error ³
³ 0B ³ Bad track error ³
³ 10 ³ ECC error ³
³ 11 ³ ECC recover enable ³
³ 20 ³ HDC error ³
³ 40 ³ Seek error ³
³ 80 ³ Time out error ³
³ AA ³ Drive not ready ³
³ BB ³ Undefined ³
³ CC ³ Write fault ³
³ E0 ³ Status error ³
³ F0 ³ Not sense error (HW.code=FF) ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Page 2-29
PROCEDURE 5
Connector Check
1. Turn off the power, then unplug the AC power cord.
2. Remove the top cover. (Refer to section 4.8)
3. Check that the HDC signal cable (PJ6) and HDD power cable (PJ11)
are secure.
4. If both cables are securely connected to the system board, go to
PROCEDURE 6.
5. If the cables are not securely connected, secure them.
Page 2-30
PROCEDURE 6
HDD Jumper Straps Check
1. Remove the disk support (Refer to section 4.12.).
2. Check that the jumper straps are set correctly as shown in figure
2-2 and described in table 2-6.
3. If the jumper straps are set correctly, go to PROCEDURE 7.
4. If the jumper straps are not set correctly, set them correctly.
Table 2-6 HDD jumper straps functions
20-Mbyte (CP3022) 20-Mbyte (CP3024) or 40-Mbyte
ÚÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄ¿
³Signal ³ Status ³ ³Signal ³ Status ³
ÃÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´ ÃÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄ´
³ E5 ³ Short ³ ³ HSP ³ Open ³
³ E6 ³ Open ³ ³ C/D ³ Short ³
³ E7 ³ Short ³ ³ DHP ³ Open ³
ÀÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÙ ³ ACT ³ Short ³
ÀÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÙ
Figure 2-2 HDD JUMPER STRAPS
Page 2-31
PROCEDURE 7
New HDD Connection
1. Turn off the power.
2. Remove the HDD. (Refer to section 4.13.)
3. Connect a new HDD to the system board without installing the HDD.
Then connect all the FRUs removed during HDD removal without
installing the FRUs.
4. If normal operation is restored, the original HDD is probably
defective. Reassemble the system.
5. If normal operation is not restored, the system board is probably
defective. Refer to section 2.4.
~~
MODEL:T3100E
Page 2-32
2.7 KEYBOARD PROBLEM ISOLATION PROCEDURESThis section describes how to determine whether or not the keyboard
is defective. Start with PROCEDURE 1 and continue with other
procedures as instructed. The procedures described in this section are:
PROCEDURE 1: Input Check
PROCEDURE 2: Keyboard Test Execution
PROCEDURE 3: Connector Check
PROCEDURE 4: New Keyboard Connection
Page 2-33
PROCEDURE 1
Input Check
1. Insert an MS-DOS system disk into the FDD.
2. Turn on the power.
3. When the prompt appears on the screen, press any of the white keys
on the keyboard (any character or the space bar).
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³CAUTION: Do not type an MS-DOS acceptable command such as del ³
³and format. Such operation may erase your important program or data.³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
If the character you press appears on the screen, press Enter. Go
to PROCEDURE 2.
4. If the character does not appear on the screen, go to PROCEDURE 3.
Toshiba Personal Computer MS-DOS Version X.XX /(RXXXXX)
(C) Copyright Toshiba Corporation 1983, 1986
(C) Copyright Microsoft Corporation 1981, 1986
Current date is XXX X_XX_19XX
Enter new date (mm-dd-yy):
Current time is X:XX:XX,XX
Enter new time: _
C-ND Version X.XX
A> abcdefghijklmnopqrst............
Page 2-34
PROCEDURE 2
Keyboard Test Execution
1. Insert the diagnostics disk into the FDD and load the test and
diagnostics program. (Refer to section 3.)
2. Run the keyboard test as indicated on the diagnostic test menu.
3. If an error is detected during the test, go to PROCEDURE 3.
4. If no error is detected during the test, the keyboard is normal.
Page 2-35
PROCEDURE 3
Connector Check
1. Turn off the power, then disconnect the AC power cord.
2. Lift up the top cover. (Refer to section 4.8.)
3. Lift up the keyboard and check that the keyboard cable (PJ3) is
securely connected to the system board. If it is securely connected,
go to PROCEDURE 4.
4. If it is not securely connected, secure it.
Page 2-36
PROCEDURE 4
New Keyboard Connection
1. Turn off the power, then unplug the AC power cord.
2. Remove the keyboard. (Refer to section 4.2.)
3. Connect a new keyboard to the system board without installing it.
4. If normal operation is restored after connecting the new keyboard,
the original keyboard is probably defective. Install the new
keyboard.
5. If normal operation is not restored, the system board is probably
defective. Refer to section 2.4.
~~
MODEL:T3100E
Page 2-37
2.8 PLASMA DISPLAY PROBLEM ISOLATION PROCEDURES
This section describes how to determine whether or not the PLASMA
DISPLAY is defective. Start with PROCEDURE 1 and continue with other
procedures as instructed. The procedures described in this section are:
PROCEDURE 1: Display Check
PROCEDURE 2: Display Test Execution
PROCEDURE 3: PDP Connector Check
PROCEDURE 4: New PDP Connection
Page 2-38
PROCEDURE 1
Display Check
1. Turn off the power.
2. Wait 5 seconds or more and turn on the power. After turning on the
power, the following message should be displayed on the upper
left-hand corner of the screen:
MEMORY TEST XXXXKB
3. If the above message appears, go to PROCEDURE 2.
4. If the above message does not appear:
(a) Check that CRT indicator is light. If CRT indicator is light,
hold the Fn key, then press the Home key.
After performing (a), reperform steps 1 and 2. If the message in
step 2 still fails to appear, go to PROCEDURE 3.
Page 2-39
PROCEDURE 2
Display Test Execution
1. Insert the diagnostics disk into the FDD and run the display test
as indicated on the diagnostic test menu.
2. If an error is detected during the display test, the system board
is probably defective. Refer to section 2.4.
3. If no error is generated, the plasma display is normal.
Page 2-40
PROCEDURE 3
PDP Connector Check
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³WARNING: Dangerous high voltage is supplied to the plasma ³
³display panel. Pay enough attention on handling. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
1. Turn off the power, then unplug the AC power cord.
2. Remove the PDP without disconnecting the cables (Refer to section
4.5.) and check that the cables are securely connected to the plasma
display board (Refer to figure 2-3.)
3. If the cable is securely connected, go to PROCEDURE 4.
4. If the cable is not securely connected, secure it.
Figure 2-3 PDP connector check
Page 2-41
PROCEDURE 4
New PDP Connection
1. Connect a new PDP without installing it.
2. If normal operation is restored after connecting the new PDP, the
original PDP is probably defective. Reassemble the system.
3. If normal operation is not restored, the system board is probably
defective. Refer to section 2.4.
Page 2-42
File No.: 960-010
~~
MODEL:T3100E
Page 3-1
3.1 GENERAL
This part explains test and diagnostics programs. That checks the
functions of all hardware modules of the T3100e.
There are 21 programs grouped into two modules: the service program
module (DIAGNOSTICS MENU) and test program module (DIAGNOSTIC TEST
MENU)
The service program module is composed of 10 tasks:
1. DIAGNOSTIC TEST
2. HARD DISK FORMAT
3. SEEK TO LANDING ZONE (HDD)
4. HEAD CLEANING
5. LOG UTILITIES
6. RUNNING TEST
7. FDD UTILITIES
8. SYSTEM CONFIGURATION
9. EXIT TO MS-DOS
10. SETUP
The test program module is composed of 11 tests:
1. SYSTEM TEST
2. MEMORY TEST
3. KEYBOARD TEST
4. DISPLAY TEST
5. FLOPPY DISK TEST
6. PRINTER TEST
7. ASYNC TEST
8. HARD DISK TEST
9. REAL TIMER TEST
10. NDP TEST
11. EXPANSION TEST
The following items are necessary for carrying out the test and
diagnostic programs.
1. T3100e diagnostics disk
2. MS-DOS system disk
3. 2DD and 2HD formatted work disks (For FDD test)
4. Cleaning disk kit (For read cleaning)
5. Printer wraparound connector
(For printer wraparound test)
6. RS-232-C wraparound connector
(For ASYNC wraparound test)
Service personnel can use these programs to isolate problems by
selecting the appropriate program and operation procedures described in
section 3.2.
~~
MODEL:T3100E
Page 3-2
3.2 OPERATIONS
1. Insert the diagnostics disk in the floppy disk drive, and turn on
the power to boot the T3100e.
2. The following message will appear:
TOSHIBA personal computer T3100e DIAGNOSTICS
version X.XX (C) copyright TOSHIBA Corp. 1988
DIAGNOSTICS MENU:
1 - DIAGNOSTIC TEST
2 - HARD DISK FORMAT
3 - SEEK TO LANDING ZONE (HDD)
4 - HEED CLEANING
5 - LOG UTILITIES
6 - RUNNING TEST
7 - FDD UTILITIES
8 - SYSTEM CONFIGURATION
9 - EXIT TO MS-DOS
0 - SETUP
PRESS [0] - [9] KEY
Detailed explanations of the service programs and the operations
are given in section 3.17 to 3.24.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ NOTE: To stop the test program: ³
³ (1) During keyboard operation, press Ctrl + C ³
³ (2) While running the test program, press Ctrl + Break ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Page 3-3
3. Type in 1, then press Enter and the following message
will appear:
TOSHIBA personal computer T3100e DIAGNOSTICS
version X.XX (C) copyright TOSHIBA Corp. 1988
DIAGNOSTIC TEST MENU:
1 - SYSTEM TEST
2 - MEMORY TEST
3 - KEYBOARD TEST
4 - DISPLAY TEST
5 - FLOPPY DISK TEST
6 - PRINTER TEST
7 - ASYNC TEST
8 - HARD DISK TEST
9 - REAL TIMER TEST
10 - NDP TEST
11 - EXPANSION TEST
88 - FDD & HDD ERROR RETRY COUNT SET
99 - EXIT TO DIAGNOSTICS MENU
PRESS [1] - [9] KEY
Numbers, 1 to 11 are diagnostic tests.
Number 88 is for setting the floppy disk drive and hard disk drive
error retry count.
Number 99 is for returning to the DIAGNOSTICS MENU.
When selecting the floppy disk test or hard disk test, special
sub-messages will appear, as described in sections 3.8 and 3.11.
4. After typing in a test number (1 to 11) of the DIAGNOSTIC TEST
MENU, pressing Enter displays as follows:
TEST NAME XXXXXXX
SUB TEST : XX ERROR COUNT : XXXXX
PASS COUNT : XXXXX READ DATA : XX
WRITE DATA : XX STATUS : XXX
ADDRESS : XXXXXX
SUB-TEST MENU:
01 - ROM CHECKSUM
02 - HW status
99 - Exit to DIAGNOSTIC TEST MENU
SELECT SUB-TEST NUMBER ? _
The screen shown above, for example, appears when you type 1
and Enter.
Page 3-4
5. Select a subtest. Type in the subtest number, then press
Enter. The following message will appear:
TEST LOOP (1:YES/2:NO) ?
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³NOTE: If you select KEYBOARD TEST, this message will not ³
³appear. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
If you select YES (by typing in 1, then pressing
Enter):
Each time a test cycle ends, it increments the pass counter by one
and repeats the test cycle.
If you select NO (by typing in 2, then pressing
Enter):
At the end of a test cycle, the test execution is terminated and you
exit to the subtest menu.
6. Type in 1 or 2, then press Enter. The
following message will appear:
ERROR STOP (1:YES/2:NO) ?
If you select YES (by typing in 1, then pressing Enter):
When an error occurs, the error status is displayed and execution
of the test program stops and the operation guide is displayed
on the right side of the display screen.
If you select NO (by typing in 2, then pressing Enter):
When an error occurs, the error status is displayed then the error
counter is incremented by one and you can continue the test.
7. Type in 1 or 2, then press Enter and the test
program will run. Each subtest is described in section 3.3.
8. When an error occurs during the test program, the following message
will appear: (if you answer YES for ERROR STOP question,)
ERROR STATUS NAME [[ HALT OPERATION ]]
1: Test End
2: Continue
3: Retry
1: Terminates the test program execution and exits to thesubtest menu.
2: Continues the test.
3: Retires the test.
The error code and error status names are described in section 3.15.
~~
MODEL:T3100E
Page 3-5
3.3 SUBTEST NAMES
Table 3-1 lists the subtest of each test program.
Table 3-1 Subtest names and execution time
ÚÄÄÄÂÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄ¿
³No.³Test name ³Subtest No.³ Subtest item ³Time[s] ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´
³ 1 ³ SYSTEM ³ 01 ³ROM checksum ³ ³
³ ³ ³ 02 ³HW status ³ ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´
³ ³ ³ 01 ³RAM constant data ³ 20 ³
³ ³ ³ 02 ³RAM address pattern data ³ 5 ³
³ 2 ³ MEMORY ³ 03 ³RAM refresh ³ 12 ³
³ ³ ³ 04 ³Protected mode ³ 50 * ³
³ ³ ³ 05 ³Extended memory ³ 50 * ³
³ ³ ³ 06 ³LIM/EMS mode ³ 22 * ³
³ ³ ³ ³Expanded memory ³ ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´
³ 3 ³ KEYBOARD ³ 01 ³Pressed key display ³ ³
³ ³ ³ 02 ³Pressed key code display ³ ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´
³ ³ ³ 01 ³VRAM read/write ³ 1 ³
³ ³ ³ 02 ³Character attributes ³ ³
³ ³ ³ 03 ³Character set ³ ³
³ ³ ³ 04 ³80*25 Character display ³ ³
³ 4 ³ DISPLAY ³ 05 ³Graphics display ³ ³
³ ³ ³ ³(color set 0/1) ³ ³
³ ³ ³ 06 ³640*200 Graphics display ³ ³
³ ³ ³ ³(mode 6) ³ ³
³ ³ ³ ³640*400 Graphics display ³ ³
³ ³ ³ ³(mode 74) ³ ³
³ ³ ³ 08 ³Display page ³ 14 ³
³ ³ ³ 09 ³"H" pattern display ³ ³
³ ³ ³ 10 ³LED & Font change ³ ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´
³ ³ ³ 01 ³Sequential read ³ 50 65 ³
³ ³ ³ 02 ³Sequential read/write ³ 80 130 ³
³ 5 ³ FDD ³ 03 ³Random address/data ³ 10 10 ³
³ ³ ³ 04 ³Write specified address ³2DD 2HD ³
³ ³ ³ 05 ³Read specified address ³ ³
ÀÄÄÄÁÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÙ
*: This execution time assumes that 2 Mbytes of expansion memory
is installed. Execution time will vary with amount of memory
installed.
Page 3-6
Table 3-1 Subtest names and execution time (continued)
ÚÄÄÄÂÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄ¿
³No.³Test name³Subtest No.³ Subtest item ³Time[s] ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄ´
³ ³ ³ 01 ³ Ripple pattern ³ 110 ³
³ 6 ³ PRINTER³ 02 ³ Function ³ 15 ³
³ ³ ³ 03 ³ Wrap around ³ 1 ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄ´
³ ³ ³ 01 ³ Wrap around (board) ³ 1 ³
³ ³ ³ 02 ³ Board (#1) board (#2) ³ ³
³ ³ ³ 03 ³ Point to point (send) ³ 1 ³
³ 7 ³ ASYNC ³ 04 ³ Point to point (receive) ³ 1 ³
³ ³ ³ 05 ³ Card modem loopback ³ 5 ³
³ ³ ³ 06 ³ Card modem on-line test ³ 10 ³
³ ³ ³ 07 ³ Dial tester test ³ 60 ³
³ ³ ³ 08 ³ Interrupt test IR 4 3 5 ³ 2 ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄ´
³ ³ ³ 01 ³ Sequential read ³ 225 ³
³ ³ ³ 02 ³ Address uniqueness ³ ³
³ ³ ³ ³ 1. Forward sequential ³ 230 ³
³ ³ ³ ³ 2. Reverse ³ 270 ³
³ ³ ³ ³ 3. Random ³ 130 ³
³ ³ ³ 03 ³ Random address/data ³ 14 ³
³ ³ ³ 04 ³ Cross talk & peak shift ³ 225 ³
³ ³ ³ 05 ³ Write/read/compare (CE) ³ ³
³ 8 ³ HDD ³ 06 ³ Write specified address ³ ³
³ ³ ³ 07 ³ Read specified address ³ ³
³ ³ ³ 08 ³ ECC circuit (CE cylinder) ³ 5 ³
³ ³ ³ 09 ³ Sequential write ³ 115 ³
³ ³ ³ 10 ³ W-R-C specified address ³ ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄ´
³ ³ ³ 01 ³ Real time test ³ ³
³ ³ ³ 02 ³ Backup memory test ³ 1 ³
³ 9 ³REAL TIME³ 03 ³ Real time carry test ³ ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄ´
³10 ³ NDP ³ 01 ³ NDP test ³ ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄ´
³ ³EXPANSION³ 01 ³ Box wrap around test ³ 3 ³
³11 ³ UNIT ³ 02 ³ Box mono video ram test ³ 1 ³
³ ³ ³ 03 ³ Wrap around test (16bit bus)³ ³
ÀÄÄÄÁÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100E
<fig id=MMS\3100E\31E3_7.TIF>Page 3-7
3.4 SYSTEM TEST
Subtest 01 ROM checksum
This test performs the ROM check sum test on the system
board.
(Test extent : F0000H - FFFFFH 64KB)
Subtest 02 H/W status
This test reads the system hardware status, then displays
the status as shown below. Press Enter to return to the
system test's SUB-TEST MENU. Table 3-2 describes the
hardware status bits. If you want to return to the SYSTEM
TEST menu, press Enter.
76543210
H/W status = 10101100
Bit7 ---Display mode = Plasma
Bit6 ---CPU clock = 12MHZ
Bit5 --
Bit4
---2MB FDD = 2MB
Bit3 ---Internal FDDs = 1
Bit2 ---Drive A/B = Normal
Bit1 ---External FDD = OFF
Bit0 ---Internal FDD = 2HD type
Table 3-2 Hardware status bit
ÚÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄ¿
³ Items ³ H/W status ³ 1 ³ 0 ³
ÃÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄ´
³ Bit7 ³ Display mode ³ Plasma ³ CRT ³
³ Bit6 ³ CPU clock ³ 6MHz ³ 12MHz ³
³ Bit5 ³ Reserved ³ ³ ³
³ Bit4 ³ 2MD FDD ³ 1.6MB ³ 2MB ³
³ Bit3 ³ Internal FDDs ³ 1 ³ 2 ³
³ Bit2 ³ Drive A/B ³ Normal ³ Change ³
³ Bit1 ³ External FDD ³ ON ³ OFF ³
³ Bit0 ³ Internal FDD ³ 2DD type³ 2HD type³
ÀÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100E
Page 3-8
3.5 MEMORY TEST
Subtest 01 RAM constant data (in real mode)
This subtest writes constant data to memory, then reads
and compares it with the original data. The constant data
is FFFFH, AAAAH, 5555H, 0101H, and 0000H.
Subtest 02 RAM address pattern data (in real mode)
This subtest creates an address pattern by XORing
(Exclusive-ORing) the address segment and address offset,
writes the address pattern into the segment address and
the offset address, then reads and compares it with the
original data.
Subtest 03 RAM refresh (in real mode)
This subtest writes 256 bytes of constant data to memory,
then reads and compares it with the original data. The
constant data is "AAAAH" and "5555H". There is a delay
between the write and the read operations.
Subtest 04 Protected mode
This subtest writes fixed data and address data to memory
(addresses 100000H to the max.) in protected mode, then
reads and compares it with the original data.
Subtest 05 Extended memory
For the memory located at the address 100000H or more,
the test program writes data, reads it back, and compares
in the microprocessor's protected mode. The data patterns
used by the program are one address pattern and four
constant (i.e. fixed) data patterns. Address pattern data
is a data generated by some logical operation with its
memory address information. Four constant data patterns
are FFFFH, AAAAH, 5555H, and 0000H.
Page 3-9
Subtest 06 LIM/EMS (Expanded memory)
Registers controlling the Lotus Intel Microsoft /
expanded memory specification (LIM/EMS) are checked.
Page information is written at the beginning of each page
to verify its paging function. Then, the memory assigned
as LIM/EMS is checked by a write/read/compare algorithm
using a LTM/EMS window.
~~
MODEL:T3100E
Page 3-9
3.6 KEYBOARD TEST
Subtest 01 Pressed key display
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³NOTE: The Fn key is not subjected to the test. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
When the keyboard layout (as shown below) is drawn on the
display, press any key and check that the corresponding
key on the screen is changed to the character 11*11 When
a key is held depressed, the display will blink
designating the auto-repeat function.
KEYBOARD TEST IN PROGRESS 30100
Figure
IF TEST OK, PRESS [DEL} THEN [ENTER] KEY
Page 3-10
Subtest 02 Pressed key code display
When a key is pressed, its scan code, character code, and
key top name are displayed on the screen in the format
shown below.
The Ins, Caps lock, Num lock, Scroll lock, Alt, Ctrl,
Left Shift, and Right Shift keys are displayed
in reverse screen when pressed.
The scan codes, character codes and key top names are
shown in APPENDIX E.
KEYBOARD TEST IN PROGRESS 30200
Scan code = XX
Character code = XX
Keytop = XXXX
Ins Lock Caps Lock Num Lock Scroll Lock
Alt Ctrl Left Shift Right Shift
PRESS [Enter] KEY
~~
MODEL:T3100E
Page 3-10
3.7 DISPLAY TEST
Subtest 01 VRAM read/write
This subtest writes constant data (FFFFH,
AAAAH, 5555H, 0000H) and address data to video
RAM (256 Kbytes), then reads the data written
and compares it with the original data.
Subtest 02 Character attributes
This subtest checks:
Normal Display
Intensified Display
Reverse Display
Blinking Display
Page 3-11
For color displays, all seven colors used (blue, red,
magenta, green, cyan, yellow, white) are displayed.
The background and foreground colors can then be
checked for brightness. The display below appears on
the screen when this test is run.
CHARACTER ATTRIBUTES
NEXT LINE SHOWS NORMAL DISPLAY.
NNNNNNNNNNNNNNNNNNNNNNNNNNNNNNN
NEXT LINE SHOWS INTENSIFIED DISPLAY.
I I I I I I I I I I I I I I I I
NEXT LINE SHOWS REVERSE DISPLAY.
RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR
NEXT LINE SHOWS BLINKING DISPLAY
BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
CHARACTER ATTRIBUTE COLORS
PRESS [ENTER] KEY
Subtest 03 Character set
In this subtest the character set of its code (00H to
FFH) is displayed in the 40 x 25 character mode as
shown below.
CHARACTER SET IN 40X25
PRESS [ENTER] KEY
Page 3-12
Subtest 04 80*25 Character display
In this subtest, the character string is displayed
shifting one character line by line in the 80*25
character mode as shown below.
80*25 CHARACTER DISPLAY
Figure
PRESS [ENTER] KEY
Subtest 05 320*200 Graphics display
This subtest displays two of color sets for the color
display in the 320*200 dots graphics mode (Mode 4) as
shown below.
320*200 GRAPHICS DISPLAY : [4]
Figure
PRESS [ENTER] KEY
Page 3-13
Subtest 06 640*200 Graphics display
This subtest displays the color blocks for the black
and white display in the 640*200 dots graphics mode
(Mode 6) as shown below.
640*200 GRAPHICS DISPLAY [6]
EVEN DOTS ODD DOTS ALL DOTS
DRIVEN DRIVEN DRIVEN
Figure
PRESS [ENTER) KEY
Subtest 07 640*400 Graphics display
This subtest displays the color blocks for the black
and white display in the 640*400 pixels graphics mode
(Mode 74) as shown below.
640*400 GRAPHICS DISPLAY : [74]
Figure
PRESS [ENTER] KEY
Page 3-14
Subtest 08 Display page
This subtest confirms that the pages can be changed
in order (page 0 to page 7) in the 40 x 25 character
mode.
DISPLAY PAGE 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Subtest 09 "H" pattern display
This subtest displays H characters on the entire
screen, as shown below.
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH
Page 3-15
Subtest 10 LED & Font change
This subtest displays as follows:
[ Speed/CRT/Caps/Num/Scroll LED test ]
(1) Press [ Fn + Pgdn ] key! ...Speed (red)
(2) Press [ Fn + Pgup ] key! ...Speed (green)
(3) Press [ Caps Lock ] key! ...Caps (on/off)
(4) Press [ Num lock ] key! ...Num (on/off)
(5) Press [Scroll lock ] key! ...Scroll (on/off)
(6) Press [ Fn + End ] key! ...CRT (on)
(7) Press [ Fn + Home ] key! ...CRT (off)
(8) Press [ Fn + ÄÄ> ] key! ...FONT change test
Press [ENTER] KEY
[HARDWARE CONFIGURATION TEST]
CHARACTER SET IN 40X25
Figure
[[XXXXXX XXXXXX XXXXXX]]
PRESS [ENTER] KEY
~~
MODEL:T3100E
Page 3-16
3.8 FLOPPY DISK TEST
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³CAUTION: Before running the floppy disk test, prepare a formatted ³
³work disk and remove the diagnostics disk. Then insert the work disk ³
³into the FDD. Because the contents of the floppy disk will be erased.³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
OPERATION
1. When you select the floppy disk test of the DIAGNOSTIC TEST MENU,
the following message will appear under the DIAGNOSTIC TEST MENU.
Test drive number select (1:FDD1,2:FDD2,0:FDD1&2) ?
2. Select the test drive number, then press the Enter. The following
message will appear.
Media in drive#1 mode (0:2DD,1:2D,2:2D-2HD/2DD,3:2HD) ?
3. Select the media type of the floppy disk to be tested, then press
the Enter. The following message will appear.
Test start track (Enter:0/dd:00-79) ?
4. You can select the start track number of the floppy disk
test.
When pressing the Enter only, the start track number will be zero.
If you desire, select the start track number. Then the subtest menu
of the floppy disk test will appear.
5. During the floppy disk test, the message shown below will appear.
The ADDRESS number indicates that the first XX shows a cylinder
number, the third X shows a head number, and the last XX shows
a sector number.
The STATUS number indicates that the first X shows a drive
number and the last XX shows an error status code.
FLOPPY DISK XXXXXXX
SUB-TEST : XX
PASS COUNT : XXXXX
WRITE DATA : XX
ADDRESS : XXXXX
ERROR COUNT : XXXXX
READ DATA : XX
STATUS : XXX
Page 3-17
CONTENTS
Subtest 01 Sequential read
This test performs the CRC (cyclic redundancy check)
with a continuous read operation of all tracks on a
floppy disk.
2D (Double-sided, double-density): Track 0 to 39.
2DD (Double-sided, double-density, double-track) and
2HD (Double-sided, high-density, double-track):
Track 0 to 79.
The start track can be specified at the previous
stage.
Subtest 02 Sequential read/write
This test writes data to all tracks (as defined
above) continuously and then reads the data out and
compares it with the original data. (The data pattern
is B5ADADH repeated.)
Subtest 03 Random address/data
This test writes random data to random address on all
tracks (as defined in subtest 01) and then reads the
data out and compares it with the original data.
Subtest 04 Write specified address
This test writes the specified data on the specified
address that you enter from the keyboard. You can
specify the test data, track number, and head number.
Subtest 05 Read specified address
This subtest performs read operation on the specified
address that you enter from the keyboard. You can
specify the track number and head number.
~~
MODEL:T3100E
Page 3-18
3.9 PRINTER TEST
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³CAUTION: A printer (IBM compatible) must be connected to the system ³
³in order to execute the test. Confirm that the A-B-PRT switch is set ³
³to PRT position. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
CONTENTS
Subtest 01 Ripple pattern
This subtest prints characters for code 20H through
7EH line by line while shifting one character to the
right at the beginning of each new line.
FIGURE
Subtest 02 Function
This subtest prints out various print type as shown
below.
FIGURE
Subtest 03 Wraparound
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³NOTE: A printer wraparound connector is necessary for³
³executing this test. Wiring diagram of the printer ³
³wraparound connector is described in the part 3.25. ³
³The data, control, and status lines will be checked ³
³with the printer wraparound connector. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Page 3-19
OPERATION
Subtest 01 and 02
1. When you select the subtest 01 or 02, the following message
will appear.
Select the channel number (1-3) ?
Select the printer channel number, then type in the number.
The T3100e supports three printer channels.
2. After pressing the Enter, the subtest is executed.
Subtest 03
1. When you select this subtest, the following message will
appear.
Select the channel number (1-3) ?
Select the printer channel number, then type in the number. The
T3100e supports three printer channels.
2. After pressing the Enter, this subtest is executed.
~~
MODEL:T3100E
Page 3-20
3.10 ASYNC TEST
In subtest 01 to subtest 05, data transmission is done with the
following format:
Speed: 9600 BPS
Data 8 bits and one parity bit (EVEN)
One stop bit
Data pattern: 20H to 7EH
Subtest 01 Wrap around (board)
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³NOTE: The RS-232-C wraparound connector must be ³
³connected to channel 1 to execute this test. The wiring ³
³diagram of the RS-232-C wraparound connector is ³
³described in part 3.25. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
A data send/receive test is performed with the wraparound
connector for the channel 1.
Subtest 02 Board (#1) board (#2)
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³NOTE: The RS-232-C direct cable (9-pin to 9-pin) must be³
³connected to channel 1 and 2 to execute this test. The ³
³wiring diagram of the RS-232-C direct cable is described³
³in part 3.25. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
The same test as the subtest 01 is performed for the
channel #1 <=> #2
Subtest 03 Point to point (send)
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³NOTE: This subtest must be executed in condition that ³
³two machines are connected with the RS-232-C direct ³
³cable and one side should be set as `send' and the other³
³set as `receive'. The wiring diagram of the RS-232-C ³
³direct cable is described in part 3.25. The subtest 03 ³
³executed in one side and the subtest 04 executed in the ³
³other will check the communication capability as ³
³follows: ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
A block of data (20H to 7EH) is sent from one side to the
other, and then returned back. The returned data is
compared with the original one. This test is used to check
whether the returned data are same as the original ones.
<fig id=MMS\3100E\31E3_21.TIF>Page 3-21
Subtest 04 Point to point (receive)
This subtest is used with the subtest 03 as described
above.
Subtest 05 110/300/1200 BPS card modem loopback
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³NOTE: If there is no modem card in the system, this test³
³can no be executed. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
This subtest is used to check whether the data to be sent
from the modem card to the RS-232-C line is correct or
not. This can be done with the loopback function inside
the modem card.
Subtest 06 110/300/1200 BPS card modem on-line test
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³NOTE: This test requires two machines which are ³
³connected to the PBX (Private Branch Exchange) One side ³
³is set as `send' and the other set as `receive'. When ³
³both sides are ready, you can start the test. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
In this subtest, data are sent from the `send' side to the
`receive' side through the PBX. This subtest is used to
check whether data transmission through a telephone line
is done properly or not.
Subtest 07 Dial tester test
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³Note: To execute this subtest, a dial tester must be ³
³connected to the system. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
This subtest is carried out by sending the pulse dial and
tone dial twice automatically.
[Pulse dial] : "1-2-3-4-5-6-7-8-9-0-1-2"
[Tone dial] : "1-2-3-4-5-6-7-8-9-*-0-#"
Subtest 08 Interrupt test (IRQ4, 3, 5)
This subtest generates the interrupt request levels 4, 3,
5 in this order, then checks if this function works
correctly.
~~
MODEL:T3100E
Page 3-22
3.11 HARD DISK TEST
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³Caution: The contents of the hard disk will be erased when subset 02, ³
³03, 04, 06, 08, 09, 10 is run. Before running the test, transfer the ³
³contents of the hard disk on the floppy disk. This can be done with ³
³the MS-DOS BACKUP command. After the test, enter the MS-DOS FDISK ³
³command, which will set the partition. Then enter the MS-DOS FORMAT ³
³command. (See the MS-DOS manual for details.) ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
OPERATION
1. When you select the hard disk test of the DIAGNOSTIC TEST MENU, the
following message will appear.
Test drive number select (1:HDD1,2:HDD2,0:HDD1&2) ?
2. Select the drive number of the hard disk to be tested and press the
Enter. The following message will appear.
HDC F/W error retry (1:yes,2:no) ?
3. This message is used to select whether to do retry operation or not
when the hard disk controller detects an error.
Select yes or no and press the Enter. The following message will
appear.
Data compare error dump (1:no,2:yes) ?
4. This message is used to select whether to do dump operation or not
when data compare error is detected. Select yes or no and press the
Enter. The following message will appear.
Detail status display (1:no,2:yes) ?
5. This message is used to select whether to display the detail status
on the screen or not. The detail status are described in section
3.16. Select yes or no and press the Enter.
Page 3-23
6. During the hard disk test, the message shown below will appear.
The ADDRESS number indicates that the first XXX shows a
cylinder number, the fourth X shows a head number, and the
last XX shows a sector number. The STATUS number indicates
that the first X shows a drive number and the last XX shows
an error status code.
HARD DISK TEST XXXXXXX
SUB-TEST : XX
PASS COUNT : XXXXX
WRITE DATA : XX
ADDRESS : XXXXXX
ERROR COUNT : XXXXX
READ DATA : XX
STATUS : XXX
CONTENTS
Subtest 01 Sequential read
This subtest performs forward reading of contents from
track 0 to Max. track and then performs reverse reading
of the contents from Max. track to track 0.
Subtest 02 Address uniqueness
1. Selecting this subtest, the following message will
appear.
Read sequential select ?
1 : Forward sequential
2 : Reverse sequential
3 : Random
2. Select one of the above and press the Enter.
This subtest writes the address data that is different
sector by sector at each track, then reads and compares it
to the original data. This test is done for all tracks.
Subtest 03 Random address/data
This subtest writes random data to random addresses
(cylinder, head, sector) and then reads the data out and
compares it to the original data.
Page 3-24
Subtest 04 Cross talk & peak shift
This subtest writes the eight types of worst pattern data
(shown below) to cylinders then reads the data while
shifting cylinder by cylinder.
Worst pattern data
1. B5ADAD .......
2. 4A5252 .......
3. EB6DB6 .......
4. 149249 .......
5. 63B63B .......
6. 9C49C4 .......
7. 2DB6DB .......
8. D24924 .......
Subtest 05 Write/Read/Compare (CE)
This subtest writes B5ADAD worst pattern data to the CE
cylinder and then reads the data out and compares it with
the original data.
Subtest 06 Write specified address
This subtest writes specified data to a specified cylinder
and head.
Subtest 07 Read specified address
This subtest reads data which has been written to a
specified cylinder and head.
Subtest 08 ECC circuit (CE cylinder)
This subtest checks the ECC (Error check and correction)
circuit functions to a specified cylinder and head.
Subtest 09 Sequential write
This subtest writes specified data of the two bytes to all
cylinder.
Subtest 10 W-R-C specified address
This subtest writes specified data to the specified
cylinder and head, then read and compare with original
data.
~~
MODEL:T3100E
Page 3-25
3.12 REAL TIMER TESTSubtest 01 Real time
A new date and time can be input during this subtest
when the current date and time are displayed.
Operations for the test are as follows.
1. Selecting the subtest, the following message
will appear.
REAL TIME TEST 901000
Current data: XX-XX-XXXX
Current time: XX:XX:XX
Enter new date:
PRESS [ENTER] KEY TO EXIT TEST
2. If current date is not correct, input the
current new date. Press the Enter, the enter
new time:message will appear.
3. If current time is not correct, input the
current new time. Press the Enter, return to
the subtest menu of the REAL TIME TEST.
Subtest 02 Backup memory
This subtest writes data (AAH, 55H) to 50 bytes of
the backup memory, and then reads and compares it
with the original data.
Subtest 03 Real time carry
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³CAUTION: When this test is executed, the ³
³current date and time is erased. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
This subtest checks whether the real time clock
increments the time displayed correctly (month, day,
year, hour, minute, second)
~~
MODEL:T3100E
Page 3-26
3.13 NDP TEST
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³CAUTION: This test cannot be run if there is no NDP mounted on ³
³the system BOARD. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Subtest 01 NDP test
This subtest checks the control word, status word,
bus, and addition/multiplication functions.
~~
MODEL:T3100E
Page 3-26
3.14 EXPANSION UNIT TEST
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³NOTE: If there is no expansion unit connected to the system, this³
³test cannot be executed. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Subtest 01 Box wrap around (8 bits bus)
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³NOTE: As this subtest required a special tool to be ³
³executed, it cannot be carried out here. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Subtest 02 Box mono video RAM
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³NOTE: If there is no monochrome display card in the³
³expansion unit, this test cannot be executed. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
This subtest writes data (FF, AA, 55, 00H) into the
monochrome display memory (B0000H to B0F9FH), then reads
the data out and compares it with the original data.
Subtest 03 Wrap around test (16 bit bus)
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³NOTE: As this subtest requires a special tool to be
³
³executed, it cannot be carried out here. If you execute
³
³the this subtest, the expansion memory not connect to
the³
³system board.
³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100E
Page 3-27
3.15 ERROR CODE AND ERROR STATUS NAMES
Table 3-3 lists the error code and error status names.
Table 3-3 Error code and error status names
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Test name ³ Error code ³ Error status name ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ EVERYTHING ³ FF ³ Compare Error ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ SYSTEM ³ 01 ³ ROM Checksum Error ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ MEMORY ³ 01 ³ Parity Error ³
³ ³ 02 ³ Protected Mode Not Change ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ FDD ³ 01 ³ Bad Command ³
³ ³ 02 ³ Address Mark Not Found ³
³ ³ 03 ³ Write Protected ³
³ ³ 04 ³ Record Not Found ³
³ ³ 06 ³ Media Removed ³
³ ³ 08 ³ DMA Overrun Error ³
³ ³ 09 ³ DMA Boundary Error ³
³ ³ 10 ³ CRC Error ³
³ ³ 20 ³ FDC Error ³
³ ³ 40 ³ Seek Error ³
³ ³ 60 ³ FDD Not Drive ³
³ ³ 80 ³ Time Out Error (Not Ready) ³
³ ³ EE ³ Write Buffer Error ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ASYNC ³ 01 ³ DSR Off Time Out ³
³ ³ 02 ³ CTS Off Time Out ³
³ ³ 04 ³ RX-Enable time out ³
³ ³ 08 ³ TX Buffer Full Time Out ³
³ ³ 10 ³ Parity Error ³
³ ³ 20 ³ Framing Error ³
³ ³ 40 ³ Overrun Error ³
³ ³ 80 ³ Line Status Error ³
³ ³ 88 ³ Modem Status Error ³
³ ³ 33 ³ No Carrier (CARD MODEM) ³
³ ³ 34 ³ Error (CARD MODEM) ³
³ ³ 36 ³ No Dial Tone CARD MODEM ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Page 3-28
Table 3-3 Error code and error status names (continued)
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Test name ³ Error code ³ Error status name ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ PRINTER ³ 01 ³ Time Out ³
³ ³ 08 ³ Fault ³
³ ³ 10 ³ Select Line ³
³ ³ 20 ³ Out Of Paper ³
³ ³ 40 ³ Power Off ³
³ ³ 80 ³ Busy Line ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ HDD ³ 01 ³ Bad Command Error ³
³ ³ 02 ³ Bad Address Mark ³
³ ³ 04 ³ Record Not Found ³
³ ³ 05 ³ HDC Not Reset ³
³ ³ 07 ³ Drive Not Initialize ³
³ ³ 09 ³ DMA Boundary Error ³
³ ³ 0A ³ Bad Sector Error ³
³ ³ 0B ³ Bad Track Error ³
³ ³ 10 ³ ECC Error ³
³ ³ 11 ³ ECC Recover Enable ³
³ ³ 20 ³ HDC Error ³
³ ³ 40 ³ Seek Error ³
³ ³ 80 ³ Time Out Error ³
³ ³ AA ³ Drive Not Ready ³
³ ³ BB ³ Undefined ³
³ ³ CC ³ Write Fault ³
³ ³ E0 ³ Status Error ³
³ ³ F0 ³ Not Sense Error (HW.code=FF) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ NDP ³ 01 ³ Not Co-processor ³
³ ³ 02 ³ Control Word Error ³
³ ³ 03 ³ Status Word Error ³
³ ³ 04 ³ Bus Error ³
³ ³ 05 ³ Addition Error ³
³ ³ 06 ³ Multiply Error ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100E
Page 3-29
3.16 HARD DISK TEST DETAIL STATUS
When an error occurs on the hard disk test, the following message will
appear.
HDC status = XXXXXXXX
Detailed status of the hard disk test error is shown on the screen by
eight-unit number. The first XXXX is error status and the last XXXX is
not used.
Error status is composed of 2 bytes; the first byte shows the contents
of the HDC status register in hexadecimal form and the other the error
register of the HDC.
These contents are described in the table 3-4 and 3-5.
Table 3-4 HDC status register contents
ÚÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³Bit³ Name ³ Description ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³7 ³ BSY ³ "0" ... HDC is busy. ³
³ ³ busy ³ "1" ... HDC is read ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³6 ³ DRDY ³ "0" ... Hard disk drive is not ³
³ ³ (drive ready) ³ ready to accept any command. ³
³ ³ ³ "1" ... Hard disk drive is read ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³5 ³ DWF ³ "0" ... DWF error is not detected. ³
³ ³ (drive write fault) ³ "1" ... Write fault condition ³
³ ³ ³ occurs. ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³4 ³ DSC ³ "0" ... The head disk drive leads ³
³ ³ (drive seek complete) ³ are not settled over a ³
³ ³ ³ track. ³
³ ³ ³ "1" ... The hard disk drive heads ³
³ ³ ³ are settled over a track. ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³3 ³ DRQ ³ "0" ... Drive is not ready to ³
³ ³ (data request) ³ transfer data. ³
³ ³ ³ "1" ... Drive is ready for data ³
³ ³ ³ transfer. ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³2 ³ CORR ³ "0" ... Otherwise ³
³ ³ (corrected data) ³ "1" ... Correctable data error is ³
³ ³ ³ corrected. ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³1 ³ IDX ³ "0" ... Otherwise ³
³ ³ (index) ³ "1" ... Index is sensed. ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³0 ³ ERR ³ "0" ... Otherwise ³
³ ³ (error) ³ "1" ... The previous command was ³
³ ³ ³ terminated with some error. ³
ÀÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Page 3-30
Table 3-5 Error register contents
ÚÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³Bit³ Name ³ Description ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³7 ³ BBK ³ "0" ... Otherwise ³
³ ³ (bad block mark) ³ "1" ... A bad block mark is ³
³ ³ ³ detected. ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³6 ³ UNC ³ "0" ... There is no uncorrectable ³
³ ³ (uncorrectable) ³ data error. ³
³ ³ ³ "1" ... Uncorrectable data error ³
³ ³ ³ has been detected. ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³5 ³ ³ Not used. ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³4 ³ IDNF ³ "0" ... Otherwise ³
³ ³ (identification) ³ "1" ... There was no ID field in ³
³ ³ ³ the requested sector. ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³3 ³ ³ Not used. ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³2 ³ ABRT ³ "0" ... Otherwise ³
³ ³ (abort) ³ "1" ... Illegal command error or a ³
³ ³ ³ drive status error occurs. ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³1 ³ TK0 ³ "0" ... The hard disk has found ³
³ ³ (track 0) ³ track 0 during a recali- ³
³ ³ ³ brate command. ³
³ ³ ³ "1" ... The hard disk could not ³
³ ³ ³ found track 0 during a ³
³ ³ ³ recalibrate command. ³
ÃÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³0 ³ ³ Not used. ³
ÀÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100E
Page 3-31
3.17 HARD DISK FORMAT
There are two types of hard disk formatting:
1. Physical formatting
2. Logical formatting
This program is for physical formatting of the hard disk; it can
execute the following items.
1. All track FORMAT
2. Good track FORMAT
3. Bad track FORMAT
4. Bad track CHECK
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³CAUTION: The contents of the hard disk will be erased when this ³
³program is run. Before running the program, transfer the contents of³
³the hard disk on to a floppy disk. This can be done with the MS-DOS ³
³BACKUP command. (See the MS-DOS manual for details.) ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
3.17.1 Program description
1. All track FORMAT
Performs physical formatting of hard disk in the manner shown
below.
20-Mbyte 40-Mbyte
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Sector sequences: 1 1
Cylinders: 0 to 614 0 to 979
Heads: 0 to 2 0 to 4
Sectors: 0 to 16 0 to 16
Sector length: (bps) 512 512
2. Good track FORMAT
Executes the formatting of a specified cylinder and track as a
good track.
3. Bad track FORMAT
Executes the formatting of a specified cylinder and track as
a bad track.
4. Bad track CHECK
Checks for bad tracks by performing a read operation for all
tracks on the hard disk; a list of bad tracks is then displayed
Page 3-32
3.17.2 Operations
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
¿
³CAUTION: After physical formatting is finished, enter the MS-DOS
FDISK³
³command, which will set the partition. Then enter the MS-DOS FORMAT
³
³command. (See the MS-DOS manual for details.)
³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Ù
1. After pressing 2 and Enter in the DIAGNOSTICS MENU,
the following display will appear.
DIAGNOSTIC - HARD DISK FORMAT V2.00
1 - All track FORMAT
2 - Good track FORMAT
3 - Bad track FORMAT
4 - Bad track CHECK
9 - Exit to DIAGNOSTICS MENU
Press [NUMBER) key ?
2. All track FORMAT Selection
(1) When all track FORMAT (1) is selected, the following message
will appear.
Drive number select (1:#1, 2:#2) ?
(2) Select a drive number. Type the drive number and press
Enter. The following message will appear.
Interleave number (3/1-3) ?
(3) Select an interleave number. (Usually select 3.) Type the
number and press Enter. The following display will
appear.
[HDD TYPE]: CYLINDER = XXX
[HDD TYPE]: HEED = X
[HDD TYPE]: SECTOR = XX
[WARNING: Current DISK data will be
completely destroyed]
Press [Bad track number (CCCH) key ?
[[cylinder,head = XXX X]]
(4) After pressing the Enter, the [[cylinder, head =
XXX X]] message will appear; then all cylinders of the
hard disk are formatted and checked.
Page 3-33
(5) After formatting the hard disk, the Format complete
message will then appear.
(6) Press the Enter to return to the HARD DISK FORMAT menu.
3. Good track FORMAT or Bad track FORMAT Selection
(1) When Good track FORMAT or Bad track FORMAT is selected, the
following message will appear.
Drive number select (1:#1, 2:#2) ?
(2) Select a drive number. Type the drive number and press
Enter. The following message will appear.
Interleave number (3/1-3) ?
(3) Select an interleave number. (Usually select 3.) Type the
number and press Enter. The following message will
appear.
[HDD TYPE): CYLINDER = XXX
[HDD TYPE): HEAD = X
[HDD TYPE): SECTOR = XX
Press [track number (CCCH)] key ?
(4) Type a track number (four digits) and press Enter.
(The first three digits are the cylinder number and the last
digit is the head number.) This executes the formatting of good
tracks or bad tracks.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³NOTE: This program can format only one track per operation.
If³
³it is desired to format several good tracks or bad tracks,
³
³repeat the operation as many times as necessary.
³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
(5) After formatting the track of the hard disk, the Format
complete message will appear.
(6) Press the Enter to return to the HARD DISK FORMAT menu.
Page 3-34
4. Bad track CHECK Selection
(1) When Bad track CHECK is selected, the following message will
appear.
Drive number select (1:#1, 2:#2) ?
(2) Select a drive number. Type the drive number and press
Enter. The following message will appear.
Interleave number (3/1-3) ?
(3) Select an interleave number. (Usually select 3.) Type the
number and press Enter.
When the following message appears, and bad tracks of the hard
disk are checked.
[HDD TYPE) : CYLINDER = XXX
[HDD TYPE) : HEAD = X
[HDD TYPE) : SECTOR = XX
[[cylinder,head = XXX XX]]
(4) After checking the bad tracks of the hard disk, the Format
complete message will appear.
(5) Press the Enter to return to the HARD DISK FORMAT menu.
~~
MODEL:T3100E
Page 3-35
3.18 SEEK TO LANDING ZONE (HDD)
3.18.1 Program description
When moving the unit, if an HDD head hits a data area severely, the
data will be lost. In order to protect the data, this program moves HDD
heads to safe areas. These areas called "landing zone".
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³NOTE: The built-in hard disk drive controls automatically the heads to³
³move to the landing zone at power down. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
3.18.2 Operations
1. After pressing 3 and Enter in the DIAGNOSTICS MENU,
the program is automatically executed and the following message will
appear.
Landing seek completed. (BDD#1)
Press [Enter) key.
2. After pressing Enter, the DIAGNOSTICS MENU appears.
~~
MODEL:T3100E
Page 3-36
3.19 HEAD CLEANING
3.19.1 Program description
This program executes head loading and seek/read operations for head
cleaning. A cleaning kit is necessary for cleaning the FDD head.
3.19.2 Operations
1. After pressing 4 and Enter in the DIAGNOSTICS MENU,
the following message will appear.
DIAGNOSTIC FLOPPY DISK HEED CLEANING: VX.XX
Mount cleaning disk(s) on drive(s).
Press any key when ready.
2. After above message appears, remove the Diagnostics disk, insert
the cleaning disk, and press any key.
3. When the Cleaning start message appears, FDD head cleaning
will begin.
4. When cleaning is finished, the display automatically returns to the
DIAGNOSTICS MENU.
~~
MODEL:T3100E
Page 3-37
3.20 LOG UTILITIES
3.20.1 Program description
This program logs error information generated, while a test is in
progress; the information is stored in the RAM.
However if the POWER switch is turned off the error information will be
lost. The error information itself is displayed as the following.
1. Error count (CNT)
2. Test name (TEST)
3. Subtest number (NAME)
4. Pass count (PASS)
5. Error status (STS)
6. Address (FDD, HDD 1 or memory; ADDR)
7. Write data (WD)
8. Read data (RD)
9. Error status name
This program can store data on a floppy disk or output information to a
printer.
Page 3-38
3.20.2 Operations
1. After pressing 5 and Enter in the DIAGNOSTICS MENU,
the error information logged in the RAM or on the floppy disk is
displayed as shown below.
XXXXX ERRORS
CNT TS-NAME PASS STS ADDR WD RD HSTS [ERROR STATUS NAME)
001 FDD 02 0000 103 00001 00 00 FDD - WRITE PROTECTED
001 FDD 01 0000 180 00001 00 00 FDD - TIME OUT ERROR
_ _ _ _ _ _ _ _ _
³ ³ ³ ³ ³ ³ ³ ³ ³
³ ³ ³ ³ ³ Address ³ ³ ³
³ ³ ³ ³ ³ ³ Read data ³
³ ³ ³ ³ Error status ³ ³
³ ³ ³ Pass count Write data ³
³ ³ ³ Error status name
³ ³ Subtest number
³ Test name
Error count
[[1:Next,2:prev,3:Exit,4:Clear,5:Print,6:FD LogRead,
7:FD LogWrite]]
2. Error information displayed on the screen can be manipulated with
the following key operation.
The 1 key scrolls the display to the next page.
The 2 key scrolls the display to the previous page.
The 3 key returns the display to the DIAGNOSTIC MENU.
The 4 key erases all error log information in RAM.
The 5 key outputs error log information to a printer.
The 6 key reads log information from a floppy disk.
The 7 key writes log information to a floppy disk.
~~
MODEL:T3100E
Page 3-39
3.21 RUNNING TEST
3.21.1 Program description
This program automatically runs the following tests in sequence.
1. System test (subtest number 01)
2. Memory test (subtest number 01, 02, 03, 04, 06)
3. Display test (subtest number 01 to 08)
4. FDD test (subtest number 02)
5. Printer test (subtest number 03)
6. Async test (subtest number 01)
7. HDD test (subtest number 01, 05)
8. Real timer (subtest number 02)
When running an FDD test, this system automatically decides whether
there are one or two FDDs.
3.21.2 Operations
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³CAUTION: Do not forget to load a work disk. If a work disk is not³
³loaded, an error will be generated during FDD testing. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
1. Remove the diagnostics disk and insert the work disk into the
floppy disk drive.
2. After pressing 6 and Enter in the DIAGNOSTIC MENU, the
following message will appear.
Printer wrap around test (Y/N) ?
3. Select whether to execute the printer wraparound test (Yes) or not
(No). Type Y or N and press Enter. (If Y is
selected, a wraparound connector must be connected to the printer
connector on the back of the unit.) The following message will
appear.
Async#1 wrap around test (Y/N) ?
Async#2 wrap around test (Y/N) ?
4. Select whether to execute the test (Yes) or not (No). Type Y
or N and press Enter. (If Y is selected, an RS-232-C
wraparound connector must be connected to the SER. A or SER. B
connector on the back or right side of the unit.)
5. This program is repeated continuously. To stop the program, press
Ctrl + Break.
~~
MODEL:T3100E
Page 3-40
3.22 FDD UTILITIES
3.22.1 Program description
These programs format and copy floppy disks, and display dump list for
both the FDD and the HDD.
1. FORMAT
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
¿
³CAUTION: The program is for only floppy disk drive test. The program
is³
³different the MS-DOS FORMAT command.
³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Ù
This program can format floppy disk (5.25-inch/3.5-inch) as follows.
(1) 2D:Double-sided, double-density, 48/67.5 TPI, MFM mode, 512
bytes, 9 sectors/track.
(2) 2DD:Double-sided, double-density, double-track, 96/135 TPI,
MFM mode, 512 bytes, 9 sectors/track.
(3) 2HD:Double-sided, high-density, double-track, 96/135 TPI,
MFM mode, 512 bytes, 18 sectors/track.
2. COPY
This program copies from sours floppy disk to target floppy disk.
3. DUMP
This program displays the contents of floppy disks (both 3.5" and
5.25") and hard disk (designated sectors)
3.22.2 Operations
1. After pressing 7 and Enter key in the DIAGNOSTICS MENU, the
following display will appear before program execution.
[FDD UTILITIES)
1 : FORMAT
2 : COPY
3 : DUMP
4 : EXIT TO DIAGNOSTICS MENU
PRESS [1] - [9] KEY
Page 3-41
2. FORMAT Selection
(1) When FORMAT is selected, the following message appears.
DIAGNOSTICS - FORMAT(V1.00)
Drive number select (1:A, 2:B) ?
(2) Select a drive number. Type the number and the following
message will then appear.
Type select (0:2DD-2DD, 1:2D-2DD,2:2D-2HD,3:2HD-2HD) ?
(3) Select a media-drive type number. Type the number and the
message similar to the below will appear.
Warning : Disk data will be destroyed.
Insert work disk in to drive A:
Press any key when ready.
(4) Remove the diagnostics disk from the FDD and insert the work
disk; press any key.
The following message will appear; formatting is then
executed.
[FDD TYPE] : TRACK = XXX
[FDD TYPE] : HEAD = X
[FDD TYPE] : SECTOR = XX
Format start
[[track, head = XXX X]]
After the floppy disk is formatted, the following message
will appear.
Format complete
Another format (1:Yes/2:No) ?
(5) If you type 1 and press Enter key, the display
will return to the message in (3) above. If you type 2
the display will return to the DIAGNOSTICS MENU.
Page 3-42
3. COPY Selection
(1) When COPY is selected, the following message will appear.
DIAGNOSTICS - COPY
Type select (0:2DD-2DD, 1:2D-2D, 2:2D-2HD, 3:2HD-2HD) ?
(2) Select a media/drive type number. Type the number. The
following message will then appear.
Insert source disk into drive A:
Press any key when ready.
(3) Remove the diagnostics disk from the FDD and insert the source
disk; press any key. The following message will appear, then
start the copy to memory.
[FDD TYPE] : TRACK = XXX
[FDD TYPE] : HEED = X
[FDD TYPE] : SECTOR = XX
Copy start
Insert target disk into drive A
Press any key when ready.
[[track, head = XXX XX]]
(4) Remove the source disk from the FDD and insert the work disk
(formatted); press any key. The [[track, head = XXX X]]
message will appear, then start the copy to work disk. When
coping cannot be done with one operation, message (2) is
displayed again. Repeat the operation. After the floppy disk
has been copied, the following message will appear.
Copy complete
Another copy (1:Yes/2:No) ?
(5) If you type 1 the display will return to the message in
(1) above. If you type 2 the display will return to the
DIAGNOSTICS MENU.
Page 3-43
4. DUMP Selection
(1) When dump is selected, the following message will appear.
[HDD&FLOPPY DISK DATA DUMP)
format type select (0:2DD,1:2D,2:2HD,3:HDD) ?
(2) Select a format type number. Type the number. If 3 is
selected, the dump lists for the hard disk are displayed
automatically.
0: Display a dump list for a floppy disk (2DD)
1: Display a dump list for a floppy disk (2D)
2: Display a dump list for a floppy disk (2HD)
3: Displays a dump list for a hard disk.
(3) If 0, 1, or 2 is selected, the following message will appear.
If 3 is selected, the dump list will appear.
Select FDD number (1:A/2:B) ?
(4) Select an FDD drive number; the following message will then
appear.
Insert source disk into drive A:
Press any key when ready.
(5) Remove the diagnostics disk from the FDD and insert a source
disk; press any key. The Track number ?? message will
then appear. Type the track number and press Enter.
(6) The Head number ? message will then appear. Type the
head number and press Enter.
(7) The Sector number ?? message will then appear. Type the
sector number and press Enter. The dump list for the
floppy disk will be displayed.
(8) After a dump list appears on the screen, the Press number
key (1:up,2:down,3:end) ? message will appear.
1. Displays the next sector dump.
2. Displays a previous sector dump.
3. Displays the following message.
Another dump (1:Yes/2:No) ?
(9) If you type 1 the display will return to the message shown
after (4) above. If you type 2 the display will return
to the DIAGNOSTICS MENU.
~~
MODEL:T3100E
Page 3-44
3.23 SYSTEM CONFIGURATION
3.23.1 Program description
This program displays the following system configuration.
1. BIOS ROM VERSION = VX.XX
2. Base memory size
3. Display type
4. A number of floppy disk drives
5. A number of async ports
6. A number of hard disk drives
7. A number of printer ports
8. Co-processor presents or not
9. Extended memory size
3.23.2 Operations
After pressing 8 and Enter key to select from the
DIAGNOSTICS MENU, the following display will appear.
SYSTEM CONFIGURATION
*-BIOS ROM VERSION = X.XX
*-640KB MEMORY
*-PLASMA DISPLAY
*-1 FLOPPY DISK DRIVE(S)
*-2 ASYNC ADAPTER(S)
*-1 HARD DISK DRIVE(S)
*-1 PRINTER ADAPTER(S)
*-0 MATH CO-PROCESSOR
*-0000KB EXTENDED MEMORY
PRESS [ENTER) KEY
Press Enter key to return to the DIAGNOSTICS MENU.
~~
MODEL:T3100E
Page 3-45
3.24 SETUP
3.24.1 Accessing the SETUP
Press: 0 followed by Enter. You see this screen:
[[System setup]]
1. Hard disk drive = 11-Cyl=615, h=4, S/T=17, Cap=2OMB
2. Memory size
System memory = 64OKB
Extended memory = OMB
Expanded memory = OMB+384KB
3. Internal KB type = 84 keys
4. Plasma font type = Single
5. Plasma font set = Standard
6. Display card = Internal CGA (80*25)
7. Card type in Expansion slot = None
8. Printer port type = Output port
9. Serial port
IRQ5 SIO base address = 3E8h
Serial A IRQ level = 4 (IRQ base address = 3F8h)
Serial B IRQ level = 3 (IRQ base address = 2F8h)
Optional port IRQ level = 5 (IRQ base address = 3E8h)
:&ua ;&da ;&ent moves between items, selects value
F1 exists, F5 sets default, F10 records changes
This menu above shows an example of setup options as they may be
currently stored in memory.
Notice that selecting the type of diskette drive is not an option. The
T3100e automatically determines what type of internal diskette drive is
installed. Also, you don't have to run the SETUP to use an external 5
1/4" diskette drive.
Press F1 if the setup options displayed accurately reflect your
hardware configuration and no changes are necessary. The system
restarts.
<fig id=MMS\3100E\31E3_46.TIF>Page 3-46
3.24.2 Changing Setup Values
You can change the setup options automatically or manually.
Automatic Reset
1 Follow these steps to set the values automatically:
Press F5. This instructs the program to reset
all the options to their factory preset values. The
program calculates how much conventional, extended
and expanded memory your T3100e has, based on whether
or not you have a memory expansion board installed.
Setup stores the value it calculates in configuration
memory along with the factory preset values for the
other options. The [[System setup]] menu
displays the new values.
2
Confirm that the new values are correct. To change any
option(s), go to the next section, Manual Reset.
3
If the new values are correct, press F1. The
system restarts.
Manual Reset
Follow these steps to change any option(s) manually:
1
Notice the cursor (reverse display highlight bar). This cursor
indicates which option is selected for change.
2
Use the up and down arrow keys (or Enter) to
move the cursor between options.
3 When the cursor highlights the value of an option you want to
change, use the left and right arrow keys to select alternate
values. The possible values for each option are shown in the
table below.
4 When you are finished making changes, press F10 to
record the new values in configuration memory.
5 SETUP displays this message:
ARE YOU SURE? (Y/N)
Review your changes. If you need to make more alterations,
press N and go back to step 2.
6 If the new values are correct, press Y. The system
restarts.
Page 3-47
3.24.3 SETUP Descriptions
This section explains the possible values for each SETUP option.
1. Hard Disk Type
As you change the values for this option using the right and left arrow
keys, the setup program displays one of the following lines:
11 - Cyl= 615, H= 4, S/T= 17, Cap 20MB
12 - Cyl= 980, H= 5, S/T= 17, Cap 40MB
No Drive
Drive Table
Abbreviation Meaning
Cyl cylinder
H head
S/T sector/track
Cap capacity
Select type 11 for the T3100e, or type 12 for the T3100e/40.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
¿
³NOTE: Automatic Reset sets correct Hard Disk Type automatically,
³
³but once the CMOS configuration error occurs the default value is
³
³forced to type 11. In the case, you have to select type 12 for the
³
³T3100e/40 by Manual Reset.
³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
Ù
Page 3-48
2. Memory Size
Configuration memory involves selecting how much RAM the system uses
for each of the three types of memory: System memory, Extended memory,
and Expanded memory.
You can set the size of the system memory either to 512KB or 640KB.
For the purposes of SETUP, the second and third memory types are
interrelated. Use these guidelines to set Extended memory first:
o Specify the size of extended memory in 0.5MB decrements from the
maximum available to OMB. The maximum memory you have depends on
whether or not the memory expansion board is installed. The
preset size of extended memory is the maximum available.
o Each time you change the size of extended memory, you also
change the size of expanded memory. Memory not used as
extended memory is automatically allocated by the system as
expanded memory. Here are two examples of how this
procedure works:
Memory Example 1: You have the 2MB memory kit installed
(there's a maximum of 2MB available for
extended memory). You specify 0.5MB of
extended memory. The system automatically
allocates 1.5MB as expanded memory.
Memory Example 2: You have the memory kit installed
(there's a maximum of 4MB available for
extended memory). You specify 2MB of
extended memory. The system automatically
allocates 2MB as expanded memory.
o Specify how you want to use the T3100e's remaining memory,
usually 384KB. (This is the system memory not accounted for by
the other figures; refer back to the discussion of memory types
in this chapter for more information.) Set this value through the
Expanded memory value of the Memory size option.
You have these choices:
blank No additional memory is allocated for
expanded memory. The only memory used
as expanded memory is what was
automatically assigned due to your choice
for Extended memory. All remaining
memory (except conventional memory) is
used as extended memory.
384KB All memory not otherwise allocated is
reserved for expanded memory, in addition
to memory allocated by your choice for
Extended memory. If you set 512KB
conventional memory, the amount of possible
expanded memory increases by 128KB. Instead
of OKB and 384KB for these values, you have
OKB and 512KB, respectively.
Page 3-49
o These tables summarize the Memory size values:
Extended/Expanded Memory Size Table
Resulting Expanded Memory Size
Extended memory with 2MB memory kit
Values
0MB 2MB
0.5MB 1.5MB
1MB 1MB
1.5MB 0.5MB
2MB 0MB
Find the amount of extended memory you wish to use in the first column.
The second column shows you how much expanded memory your T3100e will
have with the memory kit.
Additional Memory Table
Expanded memory Total Extended Total Expanded
size values Memory
blank 384KB*+ OKB+
value above value above
384KB Value above 384KB*+
value above
*Setting system memory size to 512KB increases these values by 128KB.
3. Internal KB type
This option determines which keyboard scan codes the T3100e uses:
the standard AT scan codes or enhanced AT scan codes.
84 Keys selects standard AT scan codes. This is the
preset value.
101 Keys emulates the enhanced keyboard.
Select 84 keys unless your software requires the enhanced keyboard's
scan codes.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ NOTE: Set this option to 84 keys when using a keyboard other than ³
³ the U.S.A. keyboard. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Page 3-50
4. Plasma Font Type
This option specifies which display font the T3100e uses each time you
start the system.
Single specifies light (single width) characters.
This is the preset value.
Double specifies heavy (double width) characters.
Use the Fn + right arrow to select the alternate character font
after the system is running.
5. Plasma Font Set
This option specifies which character font the T3100e uses each time
you start the system.
Standard specifies the standard North American
character set. This is the preset value.
North European specifies the North European font.
Canadian French specifies the Canadian French font.
Reserved
6. Display Card
This option lets you define the types of internal or external display
adaptor card you have attached to the T3100e. You only specify this
option when you install an optional video card in one of the expansion
slots. The setup program displays your choices a line at a time as
follows:
Internal CCA (80*25)
Internal CGA (40*25)
External CGA (80*25)
External CGA (40*25)
External MDA (Internal CGA Enable)
External Other (Internal CGA Enable)
External MDA (Internal CGA Disable)
External Other (Internal CGA Disable)
Make a selection which corresponds to your hardware configuration. If
you select a value which uses an external display card, you must
install an external display controller and disable the internal display
controller. The preset value is the first setting: Internal CGA
(80*25).
Page 3-51
7. Card type In Expansion slot
This option specifies which type of option cards are to be used by the
T3100e. (If you change this option, the new setting takes effect only
after the T3100e is restarted.) The T3100e supports two types of
expansion slots: the IBM PC 8-bit bus slot which can accommodate
industry-standard 8-bit option cards for the IBM PC, and the Toshiba
bus slot that can accommodate T3100e option cards. The T3100e supports
four types of option cards.
None No cards are installed in the expansion
slot.
Toshiba Modem Card A Toshiba modem card is installed in the
expansion slot.
Interface Card for A Toshiba expansion chassis interface
Toshiba expansion card is installed in the expansion slot.
chassis
Others Another type of card is installed in the
expansion slot.
8. Printer Port
This option specifies which type of parallel port is to be used. The
T3100e's parallel port may be configured as either an output-only port
or as an input/output port.
Output Port specifies an output-only port. This is
the preset value.
Bi-directional Port specifies an input/output port.
Page 3-52
9. Serial Port
This option allows you to change the I/O address of a serial port is
automatically established according to its interrupt level, the SETUP
program prompts you to specify only the interrupt level. The I/O
address of a serial port which is given an interrupt level of 5,
however, must be set to one of the two pedetermined I/O addresses as
shown below.
The relationship between the serial port interrupt levels and I/O
addresses is shown below.
Interrupt Level I/O Address
3 2F8H
4 3F8H
5 3E8H or 338H
The first setup item in the serial port setup menu sets the I/O address
for the serial port that is to be given an interrupt level of 5. The
SETUP program displays one of the following addresses as the possible
I/O address:
3E8H 338H
You can select the appropriate ones with the left and right arrow keys.
The second through fourth items in the serial port setup menu set the
interrupt levels of the serial ports.
When the cursor is positioned on the second serial port setup menu
item, the SETUP program displays the menu shown below. From this menu,
you can select the interrupt levels to be assigned to the serial ports.
Page 3-53
The menu indicates the specified interrupt levels in reverse video. You
can select the appropriate one with the left and right arrow keys.
After selecting the interrupt levels, press the up or down arrow key,
or the RETURN key. The menu will disappear and the original setup menu
will reappear.
[Serial port setup menus]
Serial = 4 4 3 3 4 3
Serial = 3 5 4 5 -
Optional
port IRQ level = 5 3 5 4 3 4
IRQ4 serial port base address = 3F8h
IRQ3 serial port base address = 2F8h
IRQ5 serial port base address = 3E8h
Example 1: When not using an expansion card.
The following serial port interrupt level settings are recommended:
Serial A IRQ level = 3
Serial B IRQ level = 4
Optional port IRQ level = 5
Example 2: When using a Toshiba modem card
When using a Toshiba modem card, you have to set the setup item Option
7, "Card type in Expansion slot," to specify "Toshiba Modem Card." You
also need to set the optional port IRQ level according to the I/O
address or interrupt level of the modem card that is specified by the
communication software to be used. For example, set the serial port
interrupt levels as shown below when the communications software
assumes 2F8H as the I/O address of the modem.
Serial A IRQ level = 4
Serial B IRQ level = 5
Optional port IRQ level = 3
or
Serial A IRQ level = 4
Serial B IRQ level =
Optional
port IRQ level = 3
Example 3: When using a modem card for the IBM PC
When using a modem card for the IBMPC, you have to set the setup item
Option 7, "Card type in Expansion slot." Set option 7 to "Others" when
installing the modem card in the T3100e's expansion slot, and to
"Toshiba expansion chassis" when installing the modem card in a Toshiba
Expansion Chassis.
Page 3-54
Then check the I/O address of the modem card and make sure that it does
not conflict with that of the serial A and B. For example, set the
serial port interrupt levels as shown below when the I/O address of the
modem card is 2F8H.
Serial A IRQ level = 4
Serial B IRQ level = 5
Optional port IRQ level = 3
or
Serial A IRQ level = 4
Serial B IRQ level =
Optional
port IRQ level = 3
~~
MODEL:T3100E
Page 3-55
3.25 WIRING DIAGRAM
1. Printer wraparound connector
(9) +PD7ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ -ERROR (15)
(8) +PD6ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ -AUTFD (14)
(7) +PD5ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ +SELECT (13)
(6) +PD4ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ -PINIT (16)
(5) +PD3ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄ -STROBE (1)
ÀÄÄÄÄÄÄÄÄÄÄ -ACK (10)
(4) +PD2ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ + PE (12)
(3) +PD1ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ -SLIN (17)
(2) +PD0ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ + BUSY (11)
Figure 3-1 Printer wraparound connector
2. RS-232-C Wraparound connector
(3) TRANSMIT DATAÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
(7) REQUEST TO SENDÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄ
ÀÄÄÄÄÄÄÄÄÄÄÄ
(4) DATA TERMINAL READYÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄ
ÀÄÄÄÄÄÄÄÄÄÄÄ
RECEIVE DATA (2)
CLEAR TO SEND (8)
CARRIER DETECT (1)
DATA SET READY (6)
RING INDICATE (9)
Figure 3-2 RS-232-C wraparound connector
3. RS-232-C direct cable (9-pin to 9-pin)
(3) TD
(4) DTRÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄ
ÃÄÄÄÄÄÄÄÄÄÄÄÄ
ÀÄÄÄÄÄÄÄÄÄÄÄÄ
(7) RTSÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
(5) GNDÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
(2) RDÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
(1) CDÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
(6) DSRÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄ
(8) CTSÄÄÄÄÄÄÄÄÄÄÄ´
(9) RIÄÄÄÄÄÄÄÄÄÄÄÄÙ
RD (2)
DSR (6)
CTS (8)
RI (9)
CD (1)
GND (5)
TD (3)
RTS (7)
DTR (4)
Figure 3-3 RS-232-C direct cable (9-pin to 9-pin)
Page 3-56
4. RS-232-C direct cable (9-pin to 25-pin)
(1) CDÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
(2) RDÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
(3) TDÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
(4) DTRÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
(5) GNDÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
(7) RTSÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
(6) DSRÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
(8) CTSÄÄÄÄÄÄÄÄÄÄÄ´
(9) RIÄÄÄÄÄÄÄÄÄÄÄÄÙ
RTS (4)
TD (2)
RD (3)
CTS (5)
DSR (6)
RI (22)
GND (7)
CD (8)
DTR (20)
Figure 3-4 RS-232-C direct cable (9-pin to 25-pin)
~~
MODEL:T3100E
Page 4-1
4.1 GENERAL
This PART describes how to remove the following Field Replaceable Units
(FRUs):
1. Keyboard
2. Speaker
3. Extension board
4. PDP (plasma display panel) mask
5. PDP unit
6. PDP cover
7. LED board
8. Top cover
9. Power supply unit
10. Power supply cover
11. Disk support
12. Plasma sensor
13. Lithium battery
14. FDD
15. HDD
16. Cooling fans
17. Cooling fan holder
18. Handle
19. System board
The following points must be kept in mind:
1. The system should never be disassembled unless there is a
problem (abnormal operation, etc.)
2. Only approved tools may be used.
3. After deciding the purpose of replacing the unit, and the
procedures required, do not carry out any other procedures
which are not absolutely necessary.
4. Be sure to turn the power switch off before beginning.
5. Be sure to disconnect the AC cord and all external cables
from the system unit.
6. Follow the only fixed, standard procedures.
7. After replacing a unit, confirm that the system is operating
normally.
Tools needed for unit replacement:
1. Phillips head screwdriver.
2. Tweezers.
~~
MODEL:T3100E
Page 4-2
4.2 REMOVING/REPLACING THE KEYBOARD AND SPEAKER
1. Unplug the AC power cord from the system unit.
2. Turn the system unit upside down and stand the handle (A).
3. Remove the 3 screws (B).
Figure 4-1 Base
Page 4-3
4. Remove the keyboard (C) by disengaging from 6 latches (D) on the
base (E).
5. Remove the shield plate (F) by removing 2 screws (G).
6. Disconnect the keyboard cable (H) from the system board (PJ3).
Figure 4-2 Keyboard and shield plate
Page 4-4
7. Disconnect the speaker connector (I) from the system board, then
remove the speaker (J) by disengaging from 2 tabs (K).
Figure 4-3 Speaker
8. Reverse procedure to install.
~~
MODEL:T3100E
Page 4-5
4.3 REMOVING/REPLACING THE T3100 SUPPORT BOARD
1. Unplug the AC power cord from the system unit.
2. Remove the mask panel (A) by removing 2 screws (B).
3. Remove the extension board cover (C) by removing screw (D), and
disengaging from 2 latches (E) on the base (F).
Figure 4-4 Extension board cover
Page 4-6
4. Disconnect the system interface connecter on the T3100 support board
(G) from the system board, then remove the T3100 support board.
Figure 4-5 T3100 support board
5. Reverse procedure to install.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ NOTE: To attach the IBM half size board (8-bit), use the big ³
³ size's cover included in the package. To attach the Toshiba size ³
³ card. Use the normal cover. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100E
Page 4-7
4.4 REMOVING/REPLACING THE PDP MASK
1. Unplug the AC power cord from the system unit.
2. Open the plasma display.
3. Using tweezers, peel off the label (A) and keep it in a clean place.
4. Remove 2 screws (B) fixing the PDP mask (C) by holding bottom (D)
and lifting up.
Figure 4-6 PDP mask
5. Reverse procedure to install.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ NOTE: Confirm that the PDP mask is locked into the PDP cover ³
³ with the six latches (E). ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100E
Page 4-8
4.5 REMOVING/REPLACING THE PDP UNIT
1. Remove the PDP mask according to section 4.4.
2. Remove 4 screws (A), fixing the PDP unit (B).
3. Lift up the PDP unit, then gently put it on the keyboard.
4. Disconnect the three cables (C) from the plasma display board (D).
Figure 4-7 Removing the PDP unit
5. Reverse procedure to install.
~~
MODEL:T3100E
Page 4-9
4.6 REMOVING/REPLACING THE LED BOARD
1. Remove the PDP mask and PDP unit according to sections 4.4 and 4.5.
2. Unlatch the latch (A), then remove the LED board (B) from the latch
(C).
3. To remove the LED board, disconnect the cable (D).
Figure 4-8 LED board
4. Reverse procedure to install.
~~
MODEL:T3100E
Page 4-10
4.7 REMOVING/REPLACING THE PDP COVER
1. Unplug the AC power cord from the system unit.
2. Turn the system unit upside down.
3. Remove the 5 screws (A).
Figure 4-9 Base
Page 4-11
4. Remove the keyboard, the PDP unit and the LED board according to
sections 4.2 and 4.4 through 4.6.
5. Remove 3 screws (B) in the figure 4-13 according to section 4.8.
Lift up PDP cover and top cover together and press the cable guide
(B) nail out from the other side.
6. Remove the stopper plate (C) by removing 2 screws (D) and flat head
screw (E).
Figure 4-10 Stopper plate and cable guide
Page 4-12
7. Remove 2 screws (G) from 2 hinges (F), and remove the ground wire
(H) by removing a screw (I).
8. Remove the PDP cover (J) by shift 2 hinges to inside, then turn the
PDP cover down and lift it up.
Figure 4-11 PDP cover and hinges
9. Reverse procedure to install.
Page 4-13
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ NOTE: When you pass the cables through the cable guide, be careful ³
³ as follows: ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
(1) Put the plasma display power cable (K) to your right, and the
LED board cable (L) and plasma display signal cable (M) to your
left as shown in figure 4-12.
(2) Put the cable guide in the top cover, then place each cable
in the two ditches (N) of the PDP cover assembly as shown in
figure 4-12.
Figure 4-12 Cable position
~~
MODEL:T3100E
Page 4-14
4.8 REMOVING/REPLACING THE TOP COVER
1. Remove the keyboard, the PDP unit, the LED board and the PDP cover
according to sections 4.2 and 4.5 through 4.7.
2. Remove the top cover (A) by removing 3 screws (B).
Figure 4-13 Top cover
4. Reverse procedure to install.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ NOTE: Confirm that the top cover is locked into the base with 5 ³
³ latches (C). ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100E
Page 4-15
4.9 POWER SUPPLY UNIT
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ WARNING: Pay attention to handling the power supply unit to which ³
³ high voltage is supplied. Note that it will take a few minutes to ³
³ discharge the electricity after power-off. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
1. Remove the keyboard, PDP mask, PDP unit, LED board and PDP cover
with top cover according to sections 4.2 and 4.4 through 4.8.
2. Disconnect a connector (A) from the power supply board (PJ4).
3. Remove the power supply unit (B) by removing 5 screws (C), lift up
it, then disconnect the connecter (D) from the system board (PJ7).
Figure 4-14 Power supply unit
4. Reverse procedure to install.
~~
MODEL:T3100E
Page 4-16
4.10 POWER SUPPLY COVER
1. Remove the keyboard, PDP mask PDP unit, LED board, PDP cover with
top cover and power supply unit according to sections 4.2 and 4.4
through 4.9.
2. Remove the screw and washer assemblies (A) while lifting the power
supply cover (B) slightly.
3. Remove the power supply cover by disengaging from 3 tabs (C) on the
power supply base (D).
Figure 4-15 Power supply cover
4. Reverse procedure to install.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ NOTE: In case of installing, place the power supply cover between ³
³ the power supply base and the installing plate (E) and slide, then³
³ attach with screws after tabs enter. ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100E
Page 4-17
4.11 DISK SUPPORT, PLASMA SENSOR AND LITHIUM BATTERY
1. Remove the keyboard, PDP mask, PDP unit, LED board, PDP cover with
top cover and power supply unit according to sections 4.2 and 4.4,
through 4.9.
2. Remove the disk support (A) by removing 2 screws (B).
3. Lift the disk support, then disconnect 4 connectors (C) from the
system board (D).
4. Remove the plasma sensor (E) by removing flat head screw (F).
5. Disconnect the battery connector (G) from the system board, then
remove the lithium battery (H) fixed on the system board with a
snap-on fastener.
Figure 4-16 Disk support, plasma sensor and lithium battery
6. Reverse procedure to install.
~~
MODEL:T3100E
Page 4-18
4.12 FDD
1. Remove the keyboard, PDP mask, PDP unit, LED board, PDP cover with
top cover, power supply unit and disk support according to sections
4.2, 4.4 through 4.9 and 4.11.
2. Remove FDD (A) by removing 2 screws (B) and 2 special screws (C)
from the disk support (D).
Figure 4-17 FDD
3. Reverse procedure to install
~~
MODEL:T3100E
Page 4-19
4.13 HDD
1. Remove the keyboard, PDP mask, PDP unit, LED board, PDP cover unit
with top cover, power supply unit and disk support according to
sections 4.2, 4.4 through 4.9, and 4.11.
2. Remove the HDD (A) by removing 4 special screws (B) from the disk
support (C).
Figure 4-18 HDD
3. Reverse procedure to install.
~~
MODEL:T3100E
Page 4-20
4.14 COOLING FANS
1. Remove the keyboard, PDP mask, PDP unit, LED board, PDP cover with
top cover, power supply unit and disk support according to sections
4.2, 4.4 through 4.7, 4.9 and 4.11.
2. Remove the right cooling fan (A) by lifting the cooling fan stopper
(B) after unlatching the latches (C).
3. Disconnect the connector (D) from the system board (PJ14), then
remove the left cooling fan (F) by lifting the cooling fan stopper
after unlatching the latches.
Figure 4-19 Cooling fans
4. Reverse procedure to install.
~~
MODEL:T3100E
Page 4-21
4.15 COOLING FAN HOLDER AND HANDLE
1. Remove the keyboard, PDP mask, PDP unit, LED board, PDP cover with
top cover, power supply unit, disk support and cooling fans
according to sections 4.2, 4.4 through 4.9, 4.11 and 4.14.
2. Remove the left and right cooling fan holder (A) by lifting them
after removing 2 screws (B).
3. Remove the handle (C) by shifting toward the front and pull out
after removing the cooling fan holders.
Figure 4-20 Cooling fan holder and handle
4. Reverse procedure to install.
~~
MODEL:T3100E
Page 4-22
4.16 SYSTEM BOARD
ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
º CAUTION: Remove the T3100 support board if any.º
ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ1/4
1. Remove the keyboard, PDP mask, PDP unit, LED board, PDP cover with
top cover, power supply unit, disk support, cooling fans and holders
according to sections 4.2, 4.4 through 4.9, 4.11, 4.14 and 4.15.
2. Remove the system board (A) by removing 11 screws (B).
Figure 4-21 System board
3. Reverse procedure to install.
~~
MODEL:T3100E
Page A-1
1. SYSTEM BOARD (ICS)
Figure A-1 System board (ICs)
Page A-2
(A) CPU: Central processing unit (80286-12)
(B) NDP Socket: Numeric data processing socket (80287-12)
(C) RTC: Real time clock (MC146818)
(D) SIO: Serial input/output controller (NS16450)
(E) GA-BUS: Bus controller gate array
(F) GA-DMA3: DMA controller gate array
(G) GA-MAP3: MAP controller gate array
(H) CG-ROM: Character generator ROM
(I) GA-PLC: PLC controller gate array
(J) SI: Super integration (T9761)
(K) SI: Super integration (M5M82C800)
(L) VFO: Variable frequency oscillator (MB4108A)
~~
MODEL:T3100E
Page A-3
2. SYSTEM BOARD (CONNECTORS)
Figure A-2 System board (connectors)
Page A-4
(A) PJ1: Lithium battery connector
(B) PJ2: Serial B I/F connector
(C) PJ3: Expansion bus connector (40 pin)
(D) PJ4: Expansion bus connector (60 pin)
(E) PJ5: 8-bit slot
(F) PJ6: HDD power connector
(G) PJ7: Power supply connector
(H) PJ8: FDD connector
(I) PJ10: Serial A I/F connector
(J) PJ11: HDC I/F connector
(K) PJ12: PDP/LED I/F connector
(L) PJ13: PRT/FDD connector
(M) PJ14: Cooling fan connector
(N) PJ15: CRT I/F connector
(O) PJ17: PDP sensor switch connector
~~
MODEL:T3100E
Page A-5
3. MEMORY BOARDFigure A-3 Memory board
Page A-6
(A) Option memory I/F connector
(B) System RAMs
(C) KBC: Keyboard controller (8742 or 8042)
(D) System BIOS ROMs
(E) GA-EMS2: EMS controller gate array
(F) PJ1: Selector connector
(G) PJ2: Tenkey I/F connector
(H) PJ3: Keyboard I/F connector
(I) PJ6: Speaker connector
(J) S1: A-B-PRT switch
~~
MODEL:T3100E
Page B-1
1. SYSTEM BOARD
1.1 PJ 1 Lithium Battery Connector
Table B-1 Lithium battery connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ GND ³ I ³ 2 ³ N/C ³ ³
³ 3 ³ BAT36V;100 ³ I ³ ³ ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
1.2 PJ 2 Serial B 1/F Connector
Table B-2 Serial B I/F connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ MDCD2;100 ³ I ³ 2 ³ MDRD2;100 ³ I ³
³ 3 ³ MDTD2;110 ³ O ³ 4 ³ MDDTR2;110 ³ O ³
³ 5 ³ GND ³ ³ 6 ³ MDDSR2;110 ³ I ³
³ 7 ³ MDRTS2;110 ³ O ³ 8 ³ MDCTS2;100 ³ I ³
³ 9 ³ MDRIS;100 ³ I ³ ³ ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
1.3 PJ 3 Expansion Bus Connector (40 pin)
Table B-3 Expansion bus connector pin assignment (40 pin)
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ IRQ10;100 ³ I ³ 2 ³ IRQ14;100 ³ I ³
³ 3 ³ SD8;100 ³ I/O ³ 4 ³ SD9;100 ³ I/O ³
³ 5 ³ IRQ11;100 ³ I ³ 6 ³ SD10;100 ³ I/O ³
³ 7 ³ SD11;100 ³ I/O ³ 8 ³ SD12;100 ³ I/O ³
³ 9 ³ IRQ12;100 ³ I ³ 10 ³ GND ³ ³
³ 11 ³ SD13;100 ³ I/O ³ 12 ³ SD14;100 ³ I/O ³
³ 13 ³ IRQ6;100 ³ I ³ 14 ³ SD15;100 ³ I/O ³
³ 15 ³ A22;100 ³ I/O ³ 16 ³ A23;100 ³ I/O ³
³ 17 ³ DRQ2;100 ³ I ³ 18 ³ A21;100 ³ I/O ³
³ 19 ³ A19;100 ³ I/O ³ 20 ³ A20;100 ³ I/O ³
³ 21 ³ DACK5;000 ³ O ³ 22 ³ GND ³ ³
³ 23 ³ REFRSH;OOO ³ I/O ³ 24 ³ A18;100 ³ I/O ³
³ 25 ³ MASTER;000 ³ I ³ 26 ³ A17;100 ³ I/O ³
³ 27 ³ SBHE;OOO ³ I/O ³ 28 ³ IOCHK;000 ³ I ³
³ 29 ³ MEM16;000 ³ I ³ 30 ³ GND ³ ³
³ 31 ³ IO16;000 ³ I ³ 32 ³ DACK2;000 ³ O ³
³ 33 ³ DRQ6;100 ³ I ³ 34 ³ DRQ5;100 ³ I ³
³ 35 ³ DACK5;000 ³ O ³ 36 ³ MEMR;000 ³ I/O ³
³ 37 ³ IRQ4;100 ³ I ³ 38 ³ MEMW;000 ³ I/O ³
³ 39 ³ IRQ7;100 ³ I ³ 40 ³ GND ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
Page B-2
1.4 PJ 4 Expansion Bus Connector (60 pin)
Table B-4 Expansion bus connector pin assignment (60 pin)
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ GND ³ ³ 2 ³ VCC ³ O ³
³ 3 ³ M9V ³ O ³ 4 ³ P12V ³ O ³
³ 5 ³ CCMCS3;000 ³ O ³ 6 ³ CCMCLK;000 ³ O ³
³ 7 ³ TIRQ;000 ³ I ³ 8 ³ MDSPK;000 ³ I ³
³ 9 ³ GND ³ ³ 10 ³ SA0;100 ³ I/O ³
³ 11 ³ SA1;100 ³ I/O ³ 12 ³ SA2;100 ³ I/O ³
³ 13 ³ SA3'100 ³ I/O ³ 14 ³ SA4;100 ³ I/O ³
³ 15 ³ SA5;100 ³ I/O ³ 16 ³ SA6;100 ³ I/O ³
³ 17 ³ SA7;100 ³ I/O ³ 18 ³ GND ³ ³
³ 19 ³ SA8;100 ³ I/O ³ 20 ³ SA9;100 ³ I/O ³
³ 21 ³ SA10;100 ³ I/O ³ 22 ³ SA11;100 ³ I/O ³
³ 23 ³ SA12;100 ³ I/O ³ 24 ³ SA13;100 ³ I/O ³
³ 25 ³ SA14;100 ³ I/O ³ 26 ³ SA15;100 ³ I/O ³
³ 27 ³ GND ³ ³ 28 ³ SA16;100 ³ I/O ³
³ 29 ³ SA17;100 ³ I/O ³ 30 ³ SA18;100 ³ I/O ³
³ 31 ³ SA19;100 ³ I/O ³ 32 ³ SD0;100 ³ I/O ³
³ 33 ³ SD1;100 ³ I/O ³ 34 ³ SD2;100 ³ I/O ³
³ 35 ³ SD3;100 ³ I/O ³ 36 ³ GND ³ ³
³ 37 ³ SD4;100 ³ I/O ³ 38 ³ SD5;100 ³ I/O ³
³ 39 ³ SD6;100 ³ I/O ³ 40 ³ SD7;100 ³ I/O ³
³ 41 ³ SMEMW;000 ³ O ³ 42 ³ SMEMR;000 ³ O ³
³ 43 ³ GND ³ ³ 44 ³ IOW;000 ³ I/O ³
³ 45 ³ IOR;000 ³ I/O ³ 46 ³ TC;100 ³ O ³
³ 47 ³ BALE;1 00 ³ O ³ 48 ³ RESET;101 ³ O ³
³ 49 ³ DACK1;000 ³ O ³ 50 ³ IRQ9;100 ³ I ³
³ 51 ³ GND ³ ³ 52 ³ VCC ³ O ³
³ 53 ³ SYSCLK;110 ³ O ³ 54 ³ IRQ5;100 ³ I ³
³ 55 ³ DRQ3;100 ³ I ³ 56 ³ DACK3;000 ³ O ³
³ 57 ³ DMACK;110 ³ O ³ 58 ³ DRQ1;100 ³ I ³
³ 59 ³ IORDY;100 ³ I ³ 60 ³ GND ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
Page B-3
1.5 PJ 5A 8-bit Slot
Table B-5 8-bit slot pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ IOCHK;000 ³ I ³ 2 ³ SD7;100 ³ I/O ³
³ 3 ³ SD6;100 ³ I/O ³ 4 ³ SD5;100 ³ I/O ³
³ 5 ³ SD4;100 ³ I/O ³ 6 ³ SD3;100 ³ I/O ³
³ 7 ³ SD2;100 ³ I/O ³ 8 ³ SD1;100 ³ I/O ³
³ 9 ³ SD0;100 ³ I/O ³ 10 ³ IORDY;100 ³ I/O ³
³ 11 ³ DMACK;110 ³ O ³ 12 ³ SA19;100 ³ I/O ³
³ 13 ³ SA18;100 ³ I/O ³ 14 ³ SA17;100 ³ I/O ³
³ 15 ³ SA16;100 ³ I/O ³ 16 ³ SA15;100 ³ I/O ³
³ 17 ³ SA14;100 ³ I/O ³ 18 ³ SA13;100 ³ I/O ³
³ 19 ³ SA12;100 ³ I/O ³ 20 ³ SA11;100 ³ I/O ³
³ 21 ³ SA10;100 ³ I/O ³ 22 ³ SA9;100 ³ I/O ³
³ 23 ³ SA8;100 ³ I/O ³ 24 ³ SA7;100 ³ I/O ³
³ 25 ³ SA6;100 ³ I/O ³ 26 ³ SA5;100 ³ I/O ³
³ 27 ³ SA4;100 ³ I/O ³ 28 ³ SA3;100 ³ I/O ³
³ 29 ³ SA2;100 ³ I/O ³ 30 ³ SA1;100 ³ I/O ³
³ 31 ³ SA0;100 ³ I/O ³ ³ ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
1.6 PJ 5B 8-bit Slot
Table B-6 8-bit slot pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ GND ³ ³ 2 ³ RESET;101 ³ O ³
³ 3 ³ VCC ³ ³ 4 ³ IRQ9;100 ³ I ³
³ 5 ³ M5V ³ ³ 6 ³ DRQ2;100 ³ I ³
³ 7 ³ M12V ³ ³ 8 ³ OWAIT;000 ³ I ³
³ 9 ³ P12V ³ ³ 10 ³ GND ³ ³
³ 11 ³ SMEMW;000 ³ O ³ 12 ³ SMEMR;000 ³ O ³
³ 13 ³ IOW;000 ³ I/O ³ 14 ³ IOR;000 ³ I/O ³
³ 15 ³ DACK3;000 ³ O ³ 16 ³ DRQ3;100 ³ I ³
³ 17 ³ DACK1;000 ³ O ³ 18 ³ DRQ1;100 ³ I ³
³ 19 ³ REERSH;000 ³ I/O ³ 20 ³ SYSCLK;110 ³ O ³
³ 21 ³ IRQ7;100 ³ I ³ 22 ³ IRQ6;100 ³ I ³
³ 23 ³ IRQ5;100 ³ I ³ 24 ³ IRQ4;100 ³ I ³
³ 25 ³ MIRQ3;100 ³ I ³ 26 ³ DACK2;000 ³ O ³
³ 27 ³ TC;100 ³ O ³ 28 ³ BALE;100 ³ O ³
³ 29 ³ VCC ³ O ³ 30 ³ CLKCRT;100 ³ O ³
³ 31 ³ GND ³ ³ ³ ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
Page B-4
1.7 PJ 6 HDD Power Connector
Table B-7 HDD power connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ P12V ³ O ³ 2 ³ GND ³ ³
³ 3 ³ GND ³ ³ 4 ³ P5V ³ O ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
1.8 PJ 7 Power Supply Connector
Table B-8 Power supply connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ P12V ³ I ³ 2 ³ GND ³ ³
³ 3 ³ M12V ³ I ³ 4 ³ M5V ³ I ³
³ 5 ³ GND ³ ³ 6 ³ GND ³ ³
³ 7 ³ VCC ³ I ³ 8 ³ VCC ³ I ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
1.9 PJ 8 FDD Connector
TABLE B-9 FDD Connector Pin Assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ VCC ³ O ³ 2 ³ INDEX;000 ³ I ³
³ 3 ³ VCC ³ O ³ 4 ³ FDSELA;000 ³ O ³
³ 5 ³ VCC ³ O ³ 6 ³ DSKCHG;000 ³ I ³
³ 7 ³ VCC ³ O ³ 8 ³ READY;000 ³ I ³
³ 9 ³ NOTCH0;000 ³ I ³ 10 ³ MONA;000 ³ O ³
³ 11 ³ LOWDNS;000 ³ O ³ 12 ³ FDCDCR;000 ³ O ³
³ 13 ³ GND ³ ³ 14 ³ STEP;000 ³ O ³
³ 15 ³ GND ³ ³ 16 ³ WDATA;000 ³ O ³
³ 17 ³ GND ³ ³ 18 ³ WGATE;000 ³ O ³
³ 19 ³ GND ³ ³ 20 ³ TRACKO;000 ³ I ³
³ 21 ³ GND ³ ³ 22 ³ WPROTC;000 ³ I ³
³ 23 ³ GND ³ ³ 24 ³ RDDA;000 ³ I ³
³ 25 ³ GND ³ ³ 26 ³ SIDE;000 ³ O ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
Page B-5
1.10 PJ 10 Serial A I/F Connector
Table B-10 Serial A I/F connector
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ MDCD1;100 ³ I ³ 2 ³ MDRD1;100 ³ I ³
³ 3 ³ MDTD1;110 ³ O ³ 4 ³ MDDTR1;110 ³ O ³
³ 5 ³ GND ³ ³ 6 ³ MDDSR1;110 ³ I ³
³ 7 ³ MDRTS1;110 ³ O ³ 8 ³ MDCTS1;100 ³ I ³
³ 9 ³ MDRI1;100 ³ I ³ ³ ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
1.11 PJ 11 HDC I/F Connector
Table B-11 HDC I/F connector
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ HRESET;001 ³ O ³ 2 ³ GND ³ ³
³ 3 ³ HSD7;100 ³ I/O ³ 4 ³ HSD8;100 ³ I/O ³
³ 5 ³ HSD6;100 ³ I/O ³ 6 ³ HSD9;100 ³ I/O ³
³ 7 ³ HSD5;100 ³ I/O ³ 8 ³ HSD10;100 ³ I/O ³
³ 9 ³ HSD4;100 ³ I/O ³ 10 ³ HSD11;100 ³ I/O ³
³ 11 ³ HSD3;100 ³ I/O ³ 12 ³ HSD12;100 ³ I/O ³
³ 13 ³ HSD2;100 ³ I/O ³ 14 ³ HSD13;100 ³ I/O ³
³ 15 ³ HSD1;100 ³ I/O ³ 16 ³ HSD14;100 ³ I/O ³
³ 17 ³ HSD0;100 ³ I/O ³ 18 ³ HSD15;100 ³ I/O ³
³ 19 ³ GND ³ ³ 20 ³ N/C ³ ³
³ 21 ³ N/C ³ ³ 22 ³ GND ³ ³
³ 23 ³ HIOW;001 ³ O ³ 24 ³ GND ³ ³
³ 25 ³ HIOR;001 ³ ³ 26 ³ GND ³ ³
³ 27 ³ N/C ³ ³ 28 ³ N/C ³ ³
³ 29 ³ N/C ³ ³ 30 ³ GND ³ ³
³ 31 ³ IRQ14;100 ³ I ³ 32 ³ HIO16;000 ³ I ³
³ 33 ³ HSA1;101 ³ O ³ 34 ³ N/C ³ ³
³ 35 ³ HSA0;101 ³ O ³ 36 ³ HSA2;101 ³ O ³
³ 37 ³ HDDCS0;010 ³ O ³ 38 ³ HDDCS1;000 ³ O ³
³ 39 ³ HDDLED;000 ³ I ³ 40 ³ GND ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
Page B-6
1.12 PJ 12 PDP/LED I/F Connector
Table B-12 PDP/LED I/F connector
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ PVSYKC;110 ³ O ³ 2 ³ GND ³ ³
³ 3 ³ PHSYNC;110 ³ O ³ 4 ³ GND ³ ³
³ 5 ³ PDP1;110 ³ O ³ 6 ³ PDP2;110 ³ O ³
³ 7 ³ PDP3;110 ³ O ³ 8 ³ PDP4;110 ³ O ³
³ 9 ³ GND ³ ³ 10 ³ GND ³ ³
³ 11 ³ PSCK;110 ³ O ³ 12 ³ GND ³ ³
³ 13 ³ VCC ³ ³ 14 ³ VCC ³ ³
³ 15 ³ PENA;100 ³ O ³ 16 ³ N/C ³ ³
³ 17 ³ N/C ³ ³ 18 ³ GND ³ ³
³ 19 ³ DRVALD;000 ³ ³ 20 ³ DRVBLD;000 ³ O ³
³ 21 ³ CRTLED;000 ³ O ³ 22 ³ VCC ³ ³
³ 23 ³ SEF6M;020 ³ ³ 24 ³ LEDCAP;020 ³ O ³
³ 25 ³ LEDNUM;020 ³ O ³ 26 ³ LEDSCR;020 ³ O ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
1.13 PJ 13 PRT/FDD Connector
Table B-13 PRT/FDD connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ ³ (For PRT) ³ (For EXT FDD) ³
³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ´
³ Pin ³ Signal ³ I/O ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ STROBE;000 ³ O ³ READY;100 ³ I ³
³ 2 ³ PD0;110 ³ O ³ INDEX;000 ³ I ³
³ 3 ³ PD1;110 ³ O ³ TRACK0;000 ³ I ³
³ 4 ³ PD2;110 ³ O ³ WPROTC;000 ³ I ³
³ 5 ³ PD3;110 ³ O ³ RDDA;000 ³ I ³
³ 6 ³ PD4;110 ³ O ³ DSKCHG;000 ³ I ³
³ 7 ³ PD5;110 ³ O ³ -³ ³
³ 8 ³ PD6;110 ³ O ³ -³ ³
³ 9 ³ PD7;110 ³ O ³ -³ ³
³ 10 ³ ACK;000 ³ I ³ SWFDB;000 ³ O ³
³ 11 ³ BUSY;100 ³ I ³ SWMONB;000 ³ O ³
³ 12 ³ PE;100 ³ I ³ WRDATA;000 ³ O ³
³ 13 ³ SELECT;100 ³ I ³ EXFDWE;000 ³ O ³
³ 14 ³ AUTFD;000 ³ O ³ XRATE0;000 ³ O ³
³ 15 ³ ERROR;000 ³ I ³ SIDE;000 ³ O ³
³ 16 ³ PINIT;000 ³ O ³ FDCDRC;000 ³ O ³
³ 17 ³ SLIN;000 ³ O ³ STEP;000 ³ O ³
³ 18 ³ GND ³ ³ GND ³ ³
³ 25 ³ ³ ³ ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
Page B-7
1.14 PJ 14 Cooling Fan Connector
Table B-14 Cooling fan connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ P12V ³ O ³ 2 ³ GND ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
1.15 PJ 15 CRT I/F Connector
Table B-15 CRT I/F connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ GND ³ ³ 2 ³ GND ³ ³
³ 3 ³ DRPD1;111 ³ O ³ 4 ³ DGPD2;111 ³ O ³
³ 5 ³ DBPD3;111 ³ O ³ 6 ³ DIPD4;111 ³ O ³
³ 7 ³ N/C ³ ³ 8 ³ DHSYNC;111 ³ O ³
³ 9 ³ DVXYNC;111 ³ O ³ ³ ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
1.16 PJ 17 PDP sensor switch connector
Table B-16 PDP sensor switch connector
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ GND ³ ³ 2 ³ VCC ³ O ³
³ 3 ³ PDPON;100 ³ I ³ ³ ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
~~
MODEL:T3100E
Page B-7
2. MEMORY BOARD
2.1 IS 101A Option Memory I/F Connector
Table B-17 Option memory I/F connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ VCC ³ O ³ 2 ³ CASH;000 ³ O ³
³ 3 ³ MDB;100 ³ I/O ³ 4 ³ MA0;100 ³ O ³
³ 5 ³ MA1;100 ³ O ³ 6 ³ MD9;100 ³ I/O ³
³ 7 ³ MA2;100 ³ O ³ 8 ³ MA3;100 ³ O ³
³ 9 ³ GND ³ ³ 10 ³ MA10;100 ³ I/O ³
³ 11 ³ MA4;100 ³ O ³ 12 ³ MA5;100 ³ O ³
³ 13 ³ MD11;100 ³ I/O ³ 14 ³ MA6;100 ³ O ³
³ 15 ³ MA7;100 ³ O ³ 16 ³ MD12;100 ³ I/O ³
³ 17 ³ MA8;100 ³ O ³ 18 ³ MA9;100 ³ O ³
³ 19 ³ GND ³ ³ 20 ³ MD13;100 ³ I/O ³
³ 21 ³ MEMWE;000 ³ O ³ 22 ³ GND ³ ³
³ 23 ³ MD14;100 ³ I/O ³ 24 ³ ASL256;000 ³ I ³
³ 25 ³ MD15;100 ³ I/O ³ 26 ³ PDOH;100 ³ I ³
³ 27 ³ RASA;000 ³ O ³ 28 ³ ASL1M;000 ³ I ³
³ 29 ³ PDINH;100 ³ O ³ 30 ³ VCC ³ O ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
Page B-8
2.2 IS 101B Option Memory I/F Connector
Table B-18 Option memory I/F connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ VCC ³ O ³ 2 ³ CASL;100 ³ O ³
³ 3 ³ MD0;100 ³ I/O ³ 4 ³ MA0;100 ³ O ³
³ 5 ³ MA1;100 ³ O ³ 6 ³ MD1;100 ³ I/O ³
³ 7 ³ MA2;100 ³ O ³ 8 ³ MA3;100 ³ O ³
³ 9 ³ GND ³ ³ 10 ³ MA2;100 ³ I/O ³
³ 11 ³ MA4;100 ³ O ³ 12 ³ MA5;100 ³ O ³
³ 13 ³ MD3;100 ³ I/O ³ 14 ³ MA6;100 ³ O ³
³ 15 ³ MA7;100 ³ O ³ 16 ³ MD4;100 ³ I/O ³
³ 17 ³ MA8;100 ³ O ³ 18 ³ MA9;100 ³ O ³
³ 19 ³ GND ³ ³ 20 ³ MD5;100 ³ I/O ³
³ 21 ³ MEMWE;000 ³ O ³ 22 ³ GND ³ ³
³ 23 ³ MD6;100 ³ I/O ³ 24 ³ ASL256;000 ³ I ³
³ 25 ³ MD7;100 ³ I/O ³ 26 ³ PDOL;100 ³ I ³
³ 27 ³ RASA;000 ³ O ³ 28 ³ ASL1M;000 ³ I ³
³ 29 ³ PDINL;100 ³ O ³ 30 ³ VCC ³ O ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
2.3 IS 102A Option Memory I/F Connector
Table B-19 Option memory I/F connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ VCC ³ O ³ 2 ³ CASH;000 ³ O ³
³ 3 ³ MDB;100 ³ I/O ³ 4 ³ MA0;102 ³ O ³
³ 5 ³ MA1;102 ³ O ³ 6 ³ MD9;100 ³ I/O ³
³ 7 ³ MA2;102 ³ O ³ 8 ³ MA3;102 ³ O ³
³ 9 ³ GND ³ ³ 10 ³ MD10;100 ³ I/O ³
³ 11 ³ MA4;102 ³ O ³ 12 ³ MA5;102 ³ O ³
³ 13 ³ MD11;100 ³ I/O ³ 14 ³ MA6;102 ³ O ³
³ 15 ³ MA7;102 ³ O ³ 16 ³ MD12;100 ³ I/O ³
³ 17 ³ MA8;102 ³ O ³ 18 ³ MA9;102 ³ O ³
³ 19 ³ GND ³ ³ 20 ³ MD13;100 ³ I/O ³
³ 21 ³ MEMWE;000 ³ O ³ 22 ³ GND ³ ³
³ 23 ³ MD14;100 ³ I/O ³ 24 ³ BSL256;000 ³ I ³
³ 25 ³ MD15;100 ³ I/O ³ 26 ³ PDOH;100 ³ I ³
³ 27 ³ RASB;000 ³ O ³ 28 ³ BSL1M;000 ³ I ³
³ 29 ³ PDINH;100 ³ O ³ 30 ³ VCC ³ O ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
Page B-9
2.4 IS 102B Option Memory I/F Connector
Table B-20 Option memory I/F connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ VCC ³ O ³ 2 ³ CASL;000 ³ O ³
³ 3 ³ MD0;100 ³ I/O ³ 4 ³ MA0;102 ³ O ³
³ 5 ³ MA1;102 ³ O ³ 6 ³ MD1;100 ³ I/O ³
³ 7 ³ MA2;102 ³ O ³ 8 ³ MA3;102 ³ O ³
³ 9 ³ GND ³ ³ 10 ³ MA2;100 ³ I/O ³
³ 11 ³ MA4;102 ³ O ³ 12 ³ MA5;102 ³ O ³
³ 13 ³ MD3;100 ³ I/O ³ 14 ³ MA6;102 ³ O ³
³ 15 ³ MA7;102 ³ O ³ 16 ³ MD4;100 ³ I/O ³
³ 17 ³ MA8;102 ³ O ³ 18 ³ MA9;102 ³ O ³
³ 19 ³ GND ³ ³ 20 ³ MD5;100 ³ I/O ³
³ 21 ³ MEMWE;000 ³ O ³ 22 ³ GND ³ ³
³ 23 ³ MD6;100 ³ I/O ³ 24 ³ BSL256;000 ³ I ³
³ 25 ³ MD7;100 ³ I/O ³ 26 ³ PDOL;100 ³ I ³
³ 27 ³ RASB;000 ³ O ³ 28 ³ BSL1M;000 ³ I ³
³ 29 ³ PDINL;100 ³ O ³ 30 ³ VCC ³ O ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
2.5 PJ 1 Selector Connector
Table B-21 Selector connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ GND ³ ³ 2 ³ FD2;000 ³ I ³
³ 3 ³ VCC ³ O ³ 4 ³ FD2MB;000 ³ I ³
³ 5 ³ VCC ³ O ³ 6 ³ F2HD;000 ³ I ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
2.6 PJ 2 Tenkey I/F Connector
Table B-22 Tenkey I/F connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ KBSC14;000 ³ O ³ 2 ³ KBSC13;000 ³ O ³
³ 3 ³ KBSC12;000 ³ O ³ 4 ³ KBSC11;000 ³ O ³
³ 5 ³ KBRT3;000 ³ I ³ 6 ³ KBRT2;000 ³ I ³
³ 7 ³ KBRT1;000 ³ I ³ 8 ³ KBRT0;000 ³ I ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
Page B-10
2.7 PJ 3 Keyboard Connector
Table B-23 Keyboard connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ ³ ³ ³ ³ ³ ³
³ 1 ³ KBSC0;000 ³ O ³ 2 ³ KBSC1;000 ³ O ³
³ 3 ³ KBSC2;000 ³ O ³ 4 ³ GND ³ ³
³ 5 ³ KBSC3;000 ³ O ³ 6 ³ KBSC4;000 ³ O ³
³ 7 ³ KBSC5;000 ³ O ³ 8 ³ KBSC6;000 ³ O ³
³ 9 ³ GND ³ ³ 10 ³ KBSC7;000 ³ O ³
³ 11 ³ KBSC8;000 ³ O ³ 12 ³ KBSC9;000 ³ O ³
³ 13 ³ KBSC10;000 ³ O ³ 14 ³ KBRTN0;000 ³ I ³
³ 15 ³ KBRTN1;000 ³ I ³ 16 ³ KBRTN2;000 ³ I ³
³ 17 ³ KBRTN3;000 ³ I ³ 18 ³ GND ³ ³
³ 19 ³ KBRTN4;000 ³ I ³ 20 ³ KBRTN5;000 ³ I ³
³ 21 ³ KBRTN6;000 ³ I ³ 22 ³ KBRTN7;000 ³ I ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
2.8 PJ 6 Speaker Connector
Table B-24 Speaker connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ SPKON;100 ³ O ³ 2 ³ SPVCC;100 ³ O ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
~~
MODEL:T3100E
Page B-10
3. LED BOARD
3.1 PJ 501 FH1LED Connector
Table B-25 FH1LED connector pin assignment
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ GND ³ ³ 2 ³ DRVALD;000 ³ I ³
³ 3 ³ DRVBLD;000 ³ I ³ 4 ³ CRTLED;000 ³ I ³
³ 5 ³ VCC ³ I ³ 6 ³ SEL6M;010 ³ I ³
³ 7 ³ LEDCAP;000 ³ I ³ 8 ³ LEDNUM;000 ³ I ³
³ 9 ³ LEDSCR;000 ³ I ³ ³ ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
~~
MODEL:T3100E
Page B-11
4. T3100 SUPPORT BOARD
4.1 PJ 101 System I/F Connector (40 pin)
Table B-26 System I/F connector pin assignment (40 pin)
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ IRQ10;101 ³ O ³ 2 ³ IRQ14;101 ³ O ³
³ 3 ³ SD8;101 ³ I/O ³ 4 ³ SD9;101 ³ I/O ³
³ 5 ³ IRQ11;101 ³ O ³ 6 ³ SD10;101 ³ I/O ³
³ 7 ³ SD11;101 ³ I/O ³ 8 ³ SD12;101 ³ I/O ³
³ 9 ³ IRQ12;101 ³ O ³ 10 ³ GND ³ ³
³ 11 ³ SD13;101 ³ I/O ³ 12 ³ SD14;101 ³ I/O ³
³ 13 ³ IRQ6;101 ³ O ³ 14 ³ SD15;101 ³ I/O ³
³ 15 ³ A22;101 ³ I/O ³ 16 ³ A23;101 ³ I/O ³
³ 17 ³ DRQ2;101 ³ O ³ 18 ³ A21;101 ³ I/O ³
³ 19 ³ A19;101 ³ I/O ³ 20 ³ A20;101 ³ I/O ³
³ 21 ³ DACK6;001 ³ I ³ 22 ³ GND ³ ³
³ 23 ³ REFRSH;001 ³ I/O ³ 24 ³ A18;101 ³ I/O ³
³ 25 ³ MASTER;001 ³ O ³ 26 ³ A17;101 ³ I/O ³
³ 27 ³ SBHE;001 ³ I/O ³ 28 ³ IOCHK;001 ³ O ³
³ 29 ³ MEM16;001 ³ O ³ 30 ³ GND ³ ³
³ 31 ³ IO16;001 ³ O ³ 32 ³ DACK2;001 ³ I ³
³ 33 ³ DRQ6;101 ³ O ³ 34 ³ DRQ5;101 ³ O ³
³ 35 ³ DACK5;001 ³ I ³ 36 ³ MEMR;001 ³ I/O ³
³ 37 ³ IRQ4;101 ³ O ³ 38 ³ MEMW;001 ³ I/O ³
³ 39 ³ IRQ7;101 ³ O ³ 40 ³ GND ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
I: System board ----> T3100 support board
O: T3100 support board ----> System board
Page B-12
4.2 PJ 102 System I/F Connector (60 pin)
Table B-27 System I/F connector pin assignment (60 pin)
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ GND ³ ³ 2 ³ VCC ³ ³
³ 3 ³ ESM9V ³ ³ 4 ³ EXP12V ³ ³
³ 5 ³ CCMCS3;001 ³ I ³ 6 ³ CCMCLK;101 ³ I ³
³ 7 ³ TIRQ;001 ³ O ³ 8 ³ MDSPK;001 ³ O ³
³ 9 ³ GND ³ ³ 10 ³ SA0;101 ³ I/O ³
³ 11 ³ SA1;101 ³ I/O ³ 12 ³ SA2;101 ³ I/O ³
³ 13 ³ SA3;101 ³ I/O ³ 14 ³ SA4;101 ³ I/O ³
³ 15 ³ SA5;101 ³ I/O ³ 16 ³ SA6;101 ³ I/O ³
³ 17 ³ SA7;101 ³ I/O ³ 18 ³ GND ³ ³
³ 19 ³ SA8;101 ³ I/O ³ 20 ³ SA9;101 ³ I/O ³
³ 21 ³ SA10;101 ³ I/O ³ 22 ³ SA11;101 ³ I/O ³
³ 23 ³ SA12;101 ³ I/O ³ 24 ³ SA13;101 ³ I/O ³
³ 25 ³ SA14;101 ³ I/O ³ 26 ³ SA15;101 ³ I/O ³
³ 27 ³ GND ³ ³ 28 ³ SA16;101 ³ I/O ³
³ 29 ³ SA17;101 ³ I/O ³ 30 ³ SA18;101 ³ I/O ³
³ 31 ³ SA19;101 ³ I/O ³ 32 ³ SD0;101 ³ I/O ³
³ 33 ³ SD1;101 ³ I/O ³ 34 ³ SD2;101 ³ I/O ³
³ 35 ³ SD3;101 ³ I/O ³ 36 ³ GND ³ ³
³ 37 ³ SD4;101 ³ I/O ³ 38 ³ SD5;101 ³ I/O ³
³ 39 ³ SD6;101 ³ I/O ³ 40 ³ SD7;101 ³ I/O ³
³ 41 ³ SMEMW;001 ³ I ³ 42 ³ SMEMR;001 ³ I ³
³ 43 ³ GND ³ ³ 44 ³ IOW;010 ³ I/O ³
³ 45 ³ IOR;001 ³ I/O ³ 46 ³ TC;101 ³ I ³
³ 47 ³ BALE;101 ³ I ³ 48 ³ RESET;102 ³ I ³
³ 49 ³ DACK1;001 ³ I ³ 50 ³ IRQ9;101 ³ O ³
³ 51 ³ GND ³ ³ 52 ³ VCC ³ ³
³ 53 ³ SYSCLK;111 ³ I ³ 54 ³ IRQ5;101 ³ O ³
³ 55 ³ DRQ;101 ³ O ³ 56 ³ DACK3;101 ³ I ³
³ 57 ³ DMACK;111 ³ I ³ 58 ³ DRQ1;101 ³ O ³
³ 59 ³ IORDY;101 ³ O ³ 60 ³ GND ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
I: System board ----> T3100 support board
O: T3100 support board ----> System board
Page B-13
4.3 PJ 103 Toshiba Slot (40 pin)
Table B-28 Toshiba slot pin assignment (40 pin)
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ IRQ10;101 ³ I ³ 2 ³ IRQ14;101 ³ I ³
³ 3 ³ SD8;101 ³ I/O ³ 4 ³ SD9;101 ³ I/O ³
³ 5 ³ IRQ11;101 ³ I ³ 6 ³ SD10;101 ³ I/O ³
³ 7 ³ SD11;101 ³ I/O ³ 8 ³ SD12;101 ³ I/O ³
³ 9 ³ IRQ12;101 ³ I ³ 10 ³ GND ³ ³
³ 11 ³ SD13;101 ³ I/O ³ 12 ³ SD14;101 ³ I/O ³
³ 13 ³ IRQ6;101 ³ I ³ 14 ³ SD15;101 ³ I/O ³
³ 15 ³ A22;101 ³ I/O ³ 16 ³ A23;101 ³ I/O ³
³ 17 ³ DRQ2;101 ³ I ³ 18 ³ A21;101 ³ I/O ³
³ 19 ³ A19;101 ³ I/O ³ 20 ³ A20;101 ³ I/O ³
³ 21 ³ DACK6;001 ³ O ³ 22 ³ GND ³ ³
³ 23 ³ REFRSH;001 ³ I/O ³ 24 ³ A18;101 ³ I/O ³
³ 25 ³ MASTER;001 ³ I ³ 26 ³ A17;101 ³ I/O ³
³ 27 ³ SBHE;001 ³ I/O ³ 28 ³ IOCHK;001 ³ I ³
³ 29 ³ MEM16;001 ³ I ³ 30 ³ GND ³ ³
³ 31 ³ IO16;001 ³ I ³ 32 ³ DACK2;001 ³ O ³
³ 33 ³ DRQ6;101 ³ I ³ 34 ³ DRQ5;101 ³ I ³
³ 35 ³ DACK5;001 ³ O ³ 36 ³ MEMR;001 ³ I/O ³
³ 37 ³ IRQ4;101 ³ I ³ 38 ³ MEMW;001 ³ I/O ³
³ 39 ³ IRQ7;101 ³ I ³ 40 ³ GND ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
I: Option card ----> T3100 support board
O: T3100 support board ----> Option card
Page B-14
4.4 PJ 104 Toshiba Slot (60 pin)
Table B-29 Toshiba slot pin assignment (60 pin)
ÚÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄ¿
³ Pin ³ Signal ³ I/O ³ Pin ³ Signal ³ I/O ³
ÃÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄ´
³ 1 ³ GND ³ ³ 2 ³ VCC ³ ³
³ 3 ³ EXM9V ³ ³ 4 ³ EXP12V ³ ³
³ 5 ³ CCMCS3;001 ³ O ³ 6 ³ CCMCLK;101 ³ O ³
³ 7 ³ TIRQ;001 ³ I ³ 8 ³ MDSPK;001 ³ I ³
³ 9 ³ GND ³ ³ 10 ³ SA0;101 ³ I/O ³
³ 11 ³ SA1;101 ³ I/O ³ 12 ³ SA2;101 ³ I/O ³
³ 13 ³ SA3;101 ³ I/O ³ 14 ³ SA4;101 ³ I/O ³
³ 15 ³ SA5;101 ³ I/O ³ 16 ³ SA6;101 ³ I/O ³
³ 17 ³ SA7;101 ³ I/O ³ 18 ³ GND ³ ³
³ 19 ³ SA8;101 ³ I/O ³ 20 ³ SA9;101 ³ I/O ³
³ 21 ³ SA10;101 ³ I/O ³ 22 ³ SA11;101 ³ I/O ³
³ 23 ³ SA12;101 ³ I/O ³ 24 ³ SA13;101 ³ I/O ³
³ 25 ³ SA14;101 ³ I/O ³ 26 ³ SA15;101 ³ I/O ³
³ 27 ³ GND ³ ³ 28 ³ SA16;101 ³ I/O ³
³ 29 ³ SA17;101 ³ I/O ³ 30 ³ SA18;101 ³ I/O ³
³ 31 ³ SA19;101 ³ I/O ³ 32 ³ SD0;101 ³ I/O ³
³ 33 ³ SD1;101 ³ I/O ³ 34 ³ SD2;101 ³ I/O ³
³ 35 ³ SD3;101 ³ I/O ³ 36 ³ GND ³ ³
³ 37 ³ SD4;101 ³ I/O ³ 38 ³ SD5;101 ³ I/O ³
³ 39 ³ SD6;101 ³ I/O ³ 40 ³ SD7;101 ³ I/O ³
³ 41 ³ SMEMW;001 ³ O ³ 42 ³ SMEMR;001 ³ O ³
³ 43 ³ GND ³ ³ 44 ³ IOW;010 ³ I/O ³
³ 45 ³ IOR;001 ³ I/O ³ 46 ³ TC;101 ³ O ³
³ 47 ³ BALE;101 ³ O ³ 48 ³ RESET;102 ³ O ³
³ 49 ³ DACK1;001 ³ O ³ 50 ³ IRQ9;101 ³ I ³
³ 51 ³ GND ³ ³ 52 ³ VCC ³ ³
³ 53 ³ SYSCLK;111 ³ O ³ 54 ³ IRQ5;101 ³ I ³
³ 55 ³ DRQ;101 ³ I ³ 56 ³ DACK3;001 ³ O ³
³ 57 ³ DMACK;111 ³ O ³ 58 ³ DRQ1;101 ³ I ³
³ 59 ³ IORDY;101 ³ I ³ 60 ³ GND ³ ³
ÀÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÙ
I: Option card ----> T3100 support board
O: T3100 support board ----> Option card
~~
MODEL:T3100E
Page C-1
APPENDIX C DISPLAY CODE
Table C-1 Display code
Page C-2
~~
MODEL:T3100E
Page D-1
APPENDIX D KEYBOARD SCAN/CHARACTER CODES
Table D-1 Keyboard scan/character codes
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³Cap| Key | Lower³ ³Cap| Key | Lower³ ³Cap| Key | Lower³
³No.| Top | Case ³ ³No.| Top | Case ³ ³No.| Top | Case ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³1 | ESC | 01 1B³ ³15 | Tab | 0F 09³ ³35 | H | 23 68³
³-------------------³ ³-------------------³ ³-------------------³
³2 | ! | 02 31³ ³16 | Q | 10 71³ ³36 | J | 24 6A³
³ | 1 | ³ ³-------------------³ ³-------------------³
³-------------------³ ³17 | W | 11 77³ ³37 | K | 25 6B³
³3 | @ | 03 32³ ³-------------------³ ³-------------------³
³ | 2 | ³ ³18 | E | 12 65³ ³38 | L | 26 6C³
³-------------------³ ³-------------------³ ³-------------------³
³4 | # | 04 33³ ³19 | R | 13 72³ ³39 | : | 27 3B³
³ | 3 | ³ ³-------------------³ ³ | ; | ³
³-------------------³ ³20 | T | 14 74³ ³-------------------³
³5 | $ | 05 34³ ³-------------------³ ³40 | " | 28 27³
³ | 4 | ³ ³21 | Y | 15 79³ ³ | ' | ³
³-------------------³ ³-------------------³ ³-------------------³
³6 | % | 06 35³ ³22 | U | 16 75³ ³41 | ~ | 29 60³
³ | 5 | ³ ³-------------------³ ³ | ` | ³
³-------------------³ ³23 | I | 17 69³ ³-------------------³
³7 | ^ | 07 36³ ³-------------------³ ³42 | Shift | - ³
³ | 6 | ³ ³24 | O | 18 6F³ ³ | (L) | ³
³-------------------³ ³-------------------³ ³-------------------³
³8 | & | 08 37³ ³25 | P | 19 70³ ³43 | | | 2B 5C³
³ | 7 | ³ ³-------------------³ ³ | \ | ³
³-------------------³ ³26 | { | 1A 5B³ ³-------------------³
³9 | * | 09 38³ ³ | [ | ³ ³44 | Z | 2C 7A³
³ | 8 | ³ ³-------------------³ ³-------------------³
³-------------------³ ³27 | } | 1B 5D³ ³45 | X | 2D 78³
³10 | ( | 0A 39³ ³ | ] | ³ ³-------------------³
³ | 9 | ³ ³-------------------³ ³46 | C | 2E 63³
³-------------------³ ³28 | Enter | 1C 0D³ ³-------------------³
³11 | ) | 0B 30³ ³-------------------³ ³47 | V | 2F 76³
³ | 0 | ³ ³29 | Ctrl | - ³ ³-------------------³
³-------------------³ ³-------------------³ ³48 | B | 30 62³
³12 | _ | 0C 2D³ ³30 | A | 1E 61³ ³-------------------³
³ | -| ³ ³-------------------³ ³49 | N | 31 6E³
³-------------------³ ³31 | S | 1F 73³ ³-------------------³
³13 | + | 0D 3D³ ³-------------------³ ³50 | M | 32 6D³
³ | = | ³ ³32 | D | 20 64³ ³-------------------³
³-------------------³ ³-------------------³ ³51 | | 34 2E³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³ | . | ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
<fig id=MMS\3100E\31ED_2.TIF>Page D-2
Table D-1 Keyboard scan/character codes (continued)
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³Cap| Key | Lower³ ³Cap| Key | Lower³
³No.| Top | Case ³ ³No.| Top | Case ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³53 | ? | 35 2F³ ³75 | | 4D 00³
³54 | Shift | -³ ³-------------------³
³-------------------³ ³79 | End | 4F 00³
³55 | PrtSc | 37 2A³ ³-------------------³
³ | * | ³ ³80 | _ | 50 00³
³-------------------³ ³-------------------³
³56 | Alt | -³ ³81 | PgDn | 51 00³
³-------------------³ ³-------------------³
³57 | Space | 39 20³ ³82 | Ins | 52 00³
³-------------------³ ³-------------------³
³58 | Caps | -³ ³83 | Del | 53 00³
³ | Lock | ³ ³-------------------³
³-------------------³ ³84 | Sys | -³
³59 | F1 | 3B 00³ ³ | Req | ³
³-------------------³ ³-------------------³
³60 | F2 | 3C 00³ ³85 | Fn | -³
³-------------------³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
³61 | F3 | 3D 00³
³-------------------³
³62 | F4 | 3E 00³
³-------------------³
³63 | F5 | 3F 00³
³-------------------³
³64 | F6 | 40 00³
³-------------------³
³65 | F7 | 41 00³
³-------------------³
³66 | F8 | 42 00³
³-------------------³
³67 | F9 | 43 00³
³-------------------³
³68 | F10 | 44 00³
³-------------------³
³69 | Num | -³
³ | Lock | ³
³-------------------³
³70 | Scrol | -³
³ | Lock | ³
³-------------------³
³71 | Home | 47 00³
³-------------------³
³72 | _ | 48 00³
³-------------------³
³73 | PgUp | 49 00³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100E
<fig id=MMS\3100E\31EE_1.TIF>Page E-1
1. USA VERSION
Figure E-1 USA version
~~
MODEL:T3100E
Page E-2
2. UK VERSION
Figure E-2 UK version
~~
MODEL:T3100E
Page E-3
3. GERMANY VERSION
Figure E-3 Germany version
~~
MODEL:T3100E
Page E-4
4. FRANCE VERSIONFigure E-4 France version
~~
MODEL:T3100E
Page E-5
5. SPAIN VERSIONFigure E-5 Spain version
~~
MODEL:T3100E
Page E-6
6. ITALY VERSIONFigure E-6 Italy version
~~
MODEL:T3100E
Page E-7
7. SCANDINAVIAN VERSIONFigure E-7 Scandinavian version
~~
MODEL:T3100E
Page E-8
8. SWITZERLAND VERSIONFigure E-8 Switzerland version
~~
MODEL:T3100E
Page E-9
9. KEYCAP NUMBERSFigure E-9 Keycap number
~~
MODEL:T3100SX
Page 1-5
1.1 GENERAL
The Toshiba T3100SX is one of the most advanced portable personal
computers available offering high technology, high speed, and IBM PC AT
compatibility.
The T3100SX main features are as follows:
ù The central processing unit (CPU) is the 80386SX-16 32-bit
microprocessor, operated at 16 MHz.
ù The standard memory has 1 Mbyte of random access memory (RAM)
with 16-bit data bus width, expandable up to 13 Mbytes
maximum. There is no parity bit for all memories. The RAMs
can be used as working memory, hard RAM, virtual disk,
Lotus/Intel/Microsoft expanded memory specification (LIM-
EMS).
ù The Intel80387SX-16 math co-processor can be connected.
ù The display supports high resolution plasma display panel
(PDP) with 640 by 480 pixels (dots) and 16-level gray scale,
or high resolution liquid crystal display (LCD) with 640 by
480 pixels (dots) and 16-level gray scale.
ù The display controller supports high resolution graphics
subsystem (HRGS), includes the functions of video graphics
array (VGA).
ù The hard disk drive (HDD) has a capacity of 40 Mbytes or 80
Mbytes with 25-millisecond (ms) average access time.
ù The floppy disk drive (FDD) can support 2DD (720 Kbytes) and
2HD (1.44 Mbytes) floppy disks.
ù The keyboard has 86/88-key keyboard with the keys of a
subset of the industry standard 101/102-key keyboard.
ù The universal auto-sensing AC adapter is used for world-wide
usage.
ù The Ni-Cd battery backs up the calendar clock.
ù The T3100SX can connect one 16-bit Toshiba internal modem
slot and built-in modem slot for T1200 style modem.
ù The interface connector has one PRT/EXT.FDD connector
(25-pin), two serial connectors (9-pin), one VGA connector
(15-pin) and numerical keypad connector (2-pin).
<fig id=MMS\3100SX\31SX1_6.TIF>Page 1-6
ù The T3100SX is supported by the resume feature by keeping
the data and configuration when the T3100SX power is off.
ù The real time clock (RTC) continuously keeps the date and
time even when the T3100SX power is off.
The T3100SX Personal Computer is shown in figure 1-1, and the
configuration of the T3100SX's system unit is shown in figure 1-2.
Figure 1-1 T3100SX personal computer
Page 1-7
Figure 1-2 System unit configuration
~~
MODEL:T3100SX
Page 1-8
1.2 SYSTEM BOARDFigure 1-3 shows the block diagram of the system unit.
Figure 1-3 Block diagram
Page 1-9
The system board is composed of the following components:
ù Central processing unit (CPU): 80386SX-16
ù Numeric data processor socket for the 80387SX-16 (option)
ù Universal asynchronous receive transmitter (UART): 16C450
ù Variable frequency oscillator (VFO): T8568
ù Keyboard controller (KBC) 80C42
ù Keyboard scan controller (SCC): 80C50
ù Real time clock (RTC): MC146818AF
ù Super integration (SI): T9778
SI includes the followings:
Two direct memory access controllers
(DMACs, equivalent to 82C37)
Two programmable interrupt controllers
(PICs, equivalent to 82C59)
One programmable interval timer
(PIT, equivalent to 82C54)
One floppy disk controller
(FDC, equivalent to TC8565)
One serial input output
(SIO, equivalent to TC8570)
ù Gate arrays (GAs)
The following gate arrays are mounted in the system board:
I/O controller GA (IOC-GA)
I/O decoder GA (IOD-GA)
Bus controller GA (BSC-GA)
Bus driver GA (BSD-GA)
Memory controller GA (MEC-GA)
Video graphics array GA (VGA-GA)
Paradise video graphics array 1 (PVGA1)
Backup GA (BAC-GA)
ù Digital-to-analog converter (DAC)
Page 1-10
ù Initial program loader (IPL) ROM: 128 Kbytes (96 Kbytes are
used.)
This ROM contains initial reliability test (IRT), system
basic input output system (system BIOS), and video BIOS.
ù System RAMs: 1 Mbyte
ù Backup RAMs: 32 Kbytes
ù Video RAMs: 1 Mbyte
ù Frame RAMs: 256 Kbytes
ù Memory module socket:
The memory is expandable up to 13 Mbytes maximum.
The system board is shown in figure 1-4.
Figure 1-4 System board
~~
MODEL:T3100SX
Page 1-11
1.3 3.5-INCH FLOPPY DISK DRIVE
The 3.5-inch internal FDD is a high performance, reliable and thin
drive that supports 720-Kbyte (formatted) 2DD and 1.44-Mbyte
(formatted) 2HD 3.5-inch floppy disks.
The FDD is shown in figure 1-5 and its specifications are described in
table 1-1.
Figure 1-5 3.5-inch FDD
Table 1-1 3.5-inch FDD specifications
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Item ³ 2-Mbyte mode ³ 1-Mbyte mode ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³Storage capacity (Kbytes) ³ ³ ³
³ Unformatted ³ 2,000 ³ 1,000 ³
³ Formatted ³ 1 440 ³ 720 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³Number of heads ³ 2 ³ 2 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³Number of cylinders ³ 80 ³ 80 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³Access time (ms) ³ ³ ³
³ 1 Track access ³ 3 ³ 3 ³
³ Average ³ 94 ³ 94 ³
³ Head settling time ³ 15 ³ 15 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³Recording density ³ 135 ³ 135 ³
³ (bit per inch) ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³Data transfer rate ³ 500 ³ 250 ³
³ Kbytes per second ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³Rotational speed ³ 300 ³ 300 ³
³(revolutions per minute) ³ ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³Recording method ³ MFM (Modified Frequency ³
³ ³ Modulation) ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100SX
Page 1-12
1.4 3.5-INCH HARD DISK DRIVE
The 80-Mbyte and 40-Mbyte hard disk drive (HDD) is a random access type
storage device. It is equipped with non-removal 3.5-inch magnetic disk
and mini-winchester type magnetic heads.
The HDD is shown in figure 1-6 and specifications are described in
table 1-2.
Figure 1-6 3.5-inch HDD
Page 1-13
Table 1-2 3.5-inch HDD specifications
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Item ³ 80-Mbyte ³ 40-Mbyte ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Storage capacity (Mbyte) ³ ³ ³
³ Formatted ³ 84.84 ³ 42.42 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Number of heads ³ 4 ³ 2 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Tracks per surface ³ 862+1 ³ 862+1 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Sector per track ³ 48 ³ 48 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Bytes per sector ³ 512 ³ 512 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Access time (ms) ³ ³ ³
³ Track to track ³ 8 ³ 8 ³
³ Average ³ 25 ³ 25 ³
³ Maximum ³ 45 ³ 45 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Interleave ³ 1:1 ³ 1:1 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Rotational speed (rpm) ³ ³ 2,332ñ0.1% ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Recording method ³ 2-7 RLL code ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ ³ Typical value (W) ³
³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Item ³ ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ ³ 40-Mbyte 80-Mbyte³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄ´
³Read ³ 3.0 ³ 3.2 ³
³Write ³ 3.1 ³ 3.3 ³
³Seek ³ 3.1 ³ 3.3 ³
³Stand by (motor on) ³ 1.5 ³ 1.8 ³
³Stand by (motor off) ³ 0.5 ³ 0.8 ³
³Motor starting (10 sec max.) ³ 6.0 ³ 6.0 ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÙ
~~
MODEL:T3100SX
Page 1-14
1.5 KEYBOARD
The 86/88-key keyboard with full size keys and standard spacing
provides full compatibility with standard IBM software. The keyboard
is connected to the keyboard controller on the system board through a
27-pin flat cable. The keyboard is shown in figure 1-7.
Figure 1-7 Keyboard
~~
MODEL:T3100SX
Page 1-15
1.6 DISPLAY
The display can connect the plasma display or the LCD.
These displays support 640 by 480 pixels with high resolution
graphics subsystem (HRGS) and a 16-level gray scale. This HRGS includes
the functions of video graphics array (VGA).
The display unit receives vertical and horizontal synchronizing
signals, 4-bit data signals, and shift clock for data transmission. All
signals are TTL level compatible.
The display (PDP or LCD) is shown in figure 1-8. The specifications are
described in table 1-3.
Figure 1-8 Display
Table 1-3 Display specifications
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Item ³ PDP ³ LCD ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Number of dots (dots) ³ 640x480 ³ 640x480 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Dot dimension (mm) ³ 0.20(W)x0.14(H) ³ 0.28(W)x0.28(H) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Dot pitch (mm) ³ 0.31(W)x0.31(H) ³ 0.31(W)x0.31(H) ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Display area (mm) ³ 198.4(W)x148.8(H) ³ 198.4(W)x148.8(H)³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Color ³ Neon-orange ³ Black & white ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Constant ratio ³ 100:1 ³ 12:1 ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Gray scale ³ 16-level ³ 16-level ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Power watts ³ 15.4 ³ --³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Mean time between ³ ³ ³
³ failure (MTBF) (hours)³ 20,000 ³ --³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
vBulletin® v3.6.4, Copyright ©2000-2025, Jelsoft Enterprises Ltd.