PDA

View Full Version : Per specialisti di XF86Config-4 e driver

nix.nix
27-08-2003, 10:50
Ciao a tutti,

Ho delle schede 3D molto particolari ma a cui sono molto affezzionato e credo non ci sia modo migliore per approfondire Linux che impazzire a configurarle:

ATI FURY MAXX 64MB RAM con doppio chip RAGE 128 pro

2 VOODOO2 in SLI

MATROX M3D con chip PCX2 di NEC PowerVR

Nessuna distro riesce a far partire X ne a configurare in automatico,
ma in rete ho trovato un file che volevo sottoporre al vostro parere anche se risale ad una MDK 7.2

Section "Module"
Load "dbe"
Load "type1"
Load "speedo"
Load "extmod"
Load "freetype"
EndSection

Section "Device"
BoardName "Rage128ProAGP4x(TMDS)"
BusID "1:0:0"
Driver "r128"
Identifier "Device[0]"
VendorName "ATI"
EndSection

Section "Device"
BoardName "Rage128ProAGP4x(TMDS)"
BusID "1:1:0"
Driver "r128"
Identifier "Device[1]"
VendorName "ATI"
EndSection

Section "Device"
BoardName "3DfxVoodoo2"
BusID "0:10:0"
Driver "glide"
Identifier "Device[2]"
VendorName "3Dfx"
EndSection

----------------------------------------------------------------------
Chi lo ha rilasciato dice che a lui funziona anche se non ho avuto ancora modo di provarlo, volevo sapere da voi se è possibile migliorare qualcosa

Ciao e grazie anticipatamente
alderighi
27-08-2003, 12:18
Veramente io con la fury maxx carico mandrake senza problemi tutto in automatico
nix.nix
27-08-2003, 13:37
Potresti gentilmente dirmi che versione di MDK usi e magari postarmi il file XF86Config-4 nella sezione

Section "Module"

e

Section "Device" ?
nix.nix
27-08-2003, 16:59
Ragazzi per specialisti era un modo di dire, mi basterebbe anche partire a 256 colori a 800X600

nessun consiglio ?
AnonimoVeneziano
27-08-2003, 17:02
Prima di tutto direi di evitare la MDK7.2

Ciao
nix.nix
27-08-2003, 17:07
Sono daccordo ma sia la MDK 91 che KNOPIX 3.2 mi danno lo stesso problema, e possibile che sia qualche impostazione del bios ?
nix.nix
27-08-2003, 21:02
Come posso settare la quantita di memoria in XF86Config-4 ?

Il mio XFree86.0.log mi da un:

Fatal server error :

xf86MapPciMem: Could not nmap PCI memory

base=0xdc000000,hostbase=0xdc00000,sixe=0

Invalid argument

Qualche idea ?
possi
27-08-2003, 23:09
allora prima di tutto che XFree hai? che versione?
Secondo hai provato a fare XFree86 -configure ?
Vedi che risultato ti da, se va a buon fine ti genera un file XF86Config.new (o XF86Config-4.new) , editalo cambiando il mouse lo canna sempre.
poi lancia XFree86 -xf86configure XF86Config.new
Deve andare X se ti ha creato il file, altrimenti se non trova i driver non lo fa.
Ciao.
nix.nix
28-08-2003, 08:41
Ok stesera provero,

nel frattempo vi posto il mio XFree86.0.log:


XFree86 Version 4.3.0
Release Date: 27 February 2003
X Protocol Version 11, Revision 0, Release 6.6
Build Operating System: Linux 2.4.21-0.13mdksmp i686 [ELF]
Build Date: 12 March 2003
Before reporting problems, check http://www.XFree86.Org/
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/XFree86.0.log", Time: Wed Aug 27 22:43:16 2003
(==) Using config file: "/etc/X11/XF86Config-4"
(==) ServerLayout "layout1"
(**) |-->Screen "screen1" (0)
(**) | |-->Monitor "monitor1"
(**) | |-->Device "device1"
(**) |-->Screen "screen2" (1)
(**) | |-->Monitor "monitor2"
(**) | |-->Device "device2"
(**) |-->Input Device "Keyboard1"
(WW) Option "XkbCompat" requires an string value
(**) Option "XkbModel" "pc105"
(**) XKB: model: "pc105"
(**) Option "XkbLayout" "it"
(**) XKB: layout: "it"
(WW) Option "XkbOptions" requires an string value
(==) Keyboard: CustomKeycode disabled
(**) |-->Input Device "Mouse1"
(**) FontPath set to "unix/:-1"
(==) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R6/lib/modules"
(**) Option "AllowMouseOpenFail"
Using vt 7
(--) using VT number 7

(II) Open APM successful
(II) Module ABI versions:
XFree86 ANSI C Emulation: 0.2
XFree86 Video Driver: 0.6
XFree86 XInput driver : 0.4
XFree86 Server Extension : 0.2
XFree86 Font Renderer : 0.4
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.0.0
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.4
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.6
(II) PCI: Probing config type using method 1
(II) PCI: Config type is 1
(II) PCI: stages = 0x03, oldVal1 = 0x80000060, mode1Res1 = 0x80000000
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1106,0691 card 0000,0000 rev 44 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 1106,8598 card 0000,0000 rev 00 class 06,04,00 hdr 01
(II) PCI: 00:07:0: chip 1106,0596 card 1106,0000 rev 12 class 06,01,00 hdr 80
(II) PCI: 00:07:1: chip 1106,0571 card 0000,0000 rev 06 class 01,01,8a hdr 00
(II) PCI: 00:07:2: chip 1106,3038 card 0925,1234 rev 08 class 0c,03,00 hdr 00
(II) PCI: 00:07:3: chip 1106,3051 card 0000,0000 rev 20 class 06,00,00 hdr 00
(II) PCI: 00:09:0: chip 1033,0046 card 0000,0000 rev 01 class 04,80,00 hdr 00
(II) PCI: 00:0b:0: chip 121a,0002 card 0000,0000 rev 02 class 04,00,00 hdr 00
(II) PCI: 00:0f:0: chip 121a,0002 card 0000,0000 rev 02 class 04,00,00 hdr 00
(II) PCI: 00:11:0: chip 1102,0002 card 1102,8061 rev 07 class 04,01,00 hdr 80
(II) PCI: 00:11:1: chip 1102,7002 card 1102,0020 rev 07 class 09,80,00 hdr 80
(II) PCI: 01:00:0: chip 1002,5046 card 1002,2000 rev 00 class 03,00,00 hdr 00
(II) PCI: 01:01:0: chip 1002,5046 card 1002,2001 rev 00 class 03,80,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x000c (VGA_EN is set)
(II) Bus 1 I/O range:
[0] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[B]
[1] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B]
[2] -1 0 0x0000d800 - 0x0000d8ff (0x100) IX[B]
[3] -1 0 0x0000dc00 - 0x0000dcff (0x100) IX[B]
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xe0000000 - 0xe1ffffff (0x2000000) MX[B]
(II) Bus 1 prefetchable memory range:
[0] -1 0 0xd8000000 - 0xdfffffff (0x8000000) MX[B]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:7:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(II) Host-to-PCI bridge:
(II) Bus -1: bridge is at (0:7:3), (-1,-1,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus -1 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus -1 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus -1 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(--) PCI: (0:11:0) 3Dfx Interactive, Inc. Voodoo 2 rev 2, Mem @ 0xe2000000/24
(--) PCI: (0:15:0) 3Dfx Interactive, Inc. Voodoo 2 rev 2, Mem @ 0xe3000000/24
(--) PCI:*(1:0:0) ATI Technologies Inc Rage 128 PF/PRO AGP 4x TMDS rev 0, Mem @ 0xd8000000/26, 0xe1000000/14, I/O @ 0xd000/8
(--) PCI: (1:1:0) ATI Technologies Inc Rage 128 PF/PRO AGP 4x TMDS rev 0, Mem @ 0xdc000000/26, 0xe1004000/14, I/O @ 0xd400/8
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) PCI Memory resource overlap reduced 0xd0000000 from 0xd7ffffff to 0xcfffffff
(II) Active PCI resource ranges:
[0] -1 0 0xe4000000 - 0xe43fffff (0x400000) MX[B]
[1] -1 0 0xe4400000 - 0xe440ffff (0x10000) MX[B]
[2] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[3] -1 0 0xe1004000 - 0xe1007fff (0x4000) MX[B](B)
[4] -1 0 0xdc000000 - 0xdfffffff (0x4000000) MX[B](B)
[5] -1 0 0xe1000000 - 0xe1003fff (0x4000) MX[B](B)
[6] -1 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B](B)
[7] -1 0 0xe3000000 - 0xe3ffffff (0x1000000) MX[B](B)
[8] -1 0 0xe2000000 - 0xe2ffffff (0x1000000) MX[B](B)
[9] -1 0 0x0000ec00 - 0x0000ec07 (0x8) IX[B]
[10] -1 0 0x0000e800 - 0x0000e81f (0x20) IX[B]
[11] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[12] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[13] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B](B)
[14] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[B](B)
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xe4000000 - 0xe43fffff (0x400000) MX[B]
[1] -1 0 0xe4400000 - 0xe440ffff (0x10000) MX[B]
[2] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[3] -1 0 0xe1004000 - 0xe1007fff (0x4000) MX[B](B)
[4] -1 0 0xdc000000 - 0xdfffffff (0x4000000) MX[B](B)
[5] -1 0 0xe1000000 - 0xe1003fff (0x4000) MX[B](B)
[6] -1 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B](B)
[7] -1 0 0xe3000000 - 0xe3ffffff (0x1000000) MX[B](B)
[8] -1 0 0xe2000000 - 0xe2ffffff (0x1000000) MX[B](B)
[9] -1 0 0x0000ec00 - 0x0000ec07 (0x8) IX[B]
[10] -1 0 0x0000e800 - 0x0000e81f (0x20) IX[B]
[11] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[12] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[13] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B](B)
[14] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[B](B)
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xe4000000 - 0xe43fffff (0x400000) MX[B]
[6] -1 0 0xe4400000 - 0xe440ffff (0x10000) MX[B]
[7] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[8] -1 0 0xe1004000 - 0xe1007fff (0x4000) MX[B](B)
[9] -1 0 0xdc000000 - 0xdfffffff (0x4000000) MX[B](B)
[10] -1 0 0xe1000000 - 0xe1003fff (0x4000) MX[B](B)
[11] -1 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B](B)
[12] -1 0 0xe3000000 - 0xe3ffffff (0x1000000) MX[B](B)
[13] -1 0 0xe2000000 - 0xe2ffffff (0x1000000) MX[B](B)
[14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[15] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[16] -1 0 0x0000ec00 - 0x0000ec07 (0x8) IX[B]
[17] -1 0 0x0000e800 - 0x0000e81f (0x20) IX[B]
[18] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[19] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[20] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B](B)
[21] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[B](B)
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.0.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.2
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.0.0
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.2
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension FontCache
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "type1"
(II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a
(II) Module type1: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.0.2
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.4
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "speedo"
(II) Loading /usr/X11R6/lib/modules/fonts/libspeedo.a
(II) Module speedo: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.0.1
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.4
(II) Loading font Speedo
(II) LoadModule: "freetype"
(II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.a
(II) Module freetype: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 2.0.2
Module class: XFree86 Font Renderer
ABI class: XFree86 Font Renderer, version 0.4
(II) Loading font FreeType
(II) LoadModule: "glx"
(II) Loading /usr/X11R6/lib/modules/extensions/libglx.a
(II) Module glx: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.2
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a
(II) Module GLcore: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.2
(II) Loading extension GLX
(II) LoadModule: "dri"
(II) Loading /usr/X11R6/lib/modules/extensions/libdri.a
(II) Module dri: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.2
(II) Loading sub module "drm"
(II) LoadModule: "drm"
(II) Loading /usr/X11R6/lib/modules/linux/libdrm.a
(II) Module drm: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.0.0
ABI class: XFree86 Server Extension, version 0.2
(II) Loading extension XFree86-DRI
(II) LoadModule: "r128"
(II) Loading /usr/X11R6/lib/modules/drivers/r128_drv.o
(II) Module r128: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 4.0.1
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.6
(II) LoadModule: "ati"
(II) Loading /usr/X11R6/lib/modules/drivers/ati_drv.o
(II) Module ati: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 6.4.18
Module class: XFree86 Video Driver
ABI class: XFree86 Video Driver, version 0.6
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.0.0
Module class: XFree86 XInput Driver
ABI class: XFree86 XInput driver, version 0.4
(II) ATI: ATI driver (version 6.4.18) for chipsets: ati, ativga
(II) R128: Driver for ATI Rage 128 chipsets:
ATI Rage 128 Mobility M3 LE (PCI), ATI Rage 128 Mobility M3 LF (AGP),
ATI Rage 128 Mobility M4 MF (AGP), ATI Rage 128 Mobility M4 ML (AGP),
ATI Rage 128 Pro GL PA (PCI/AGP), ATI Rage 128 Pro GL PB (PCI/AGP),
ATI Rage 128 Pro GL PC (PCI/AGP), ATI Rage 128 Pro GL PD (PCI),
ATI Rage 128 Pro GL PE (PCI/AGP), ATI Rage 128 Pro GL PF (AGP),
ATI Rage 128 Pro VR PG (PCI/AGP), ATI Rage 128 Pro VR PH (PCI/AGP),
ATI Rage 128 Pro VR PI (PCI/AGP), ATI Rage 128 Pro VR PJ (PCI/AGP),
ATI Rage 128 Pro VR PK (PCI/AGP), ATI Rage 128 Pro VR PL (PCI/AGP),
ATI Rage 128 Pro VR PM (PCI/AGP), ATI Rage 128 Pro VR PN (PCI/AGP),
ATI Rage 128 Pro VR PO (PCI/AGP), ATI Rage 128 Pro VR PP (PCI),
ATI Rage 128 Pro VR PQ (PCI/AGP), ATI Rage 128 Pro VR PR (PCI),
ATI Rage 128 Pro VR PS (PCI/AGP), ATI Rage 128 Pro VR PT (PCI/AGP),
ATI Rage 128 Pro VR PU (PCI/AGP), ATI Rage 128 Pro VR PV (PCI/AGP),
ATI Rage 128 Pro VR PW (PCI/AGP), ATI Rage 128 Pro VR PX (PCI/AGP),
ATI Rage 128 GL RE (PCI), ATI Rage 128 GL RF (AGP),
ATI Rage 128 RG (AGP), ATI Rage 128 VR RK (PCI),
ATI Rage 128 VR RL (AGP), ATI Rage 128 4X SE (PCI/AGP),
ATI Rage 128 4X SF (PCI/AGP), ATI Rage 128 4X SG (PCI/AGP),
ATI Rage 128 4X SH (PCI/AGP), ATI Rage 128 4X SK (PCI/AGP),
ATI Rage 128 4X SL (PCI/AGP), ATI Rage 128 4X SM (AGP),
ATI Rage 128 4X SN (PCI/AGP), ATI Rage 128 Pro ULTRA TF (AGP),
ATI Rage 128 Pro ULTRA TL (AGP), ATI Rage 128 Pro ULTRA TR (AGP),
ATI Rage 128 Pro ULTRA TS (AGP?), ATI Rage 128 Pro ULTRA TT (AGP?),
ATI Rage 128 Pro ULTRA TU (AGP?)
(II) RADEON: Driver for ATI Radeon chipsets: ATI Radeon QD (AGP),
ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
ATI Radeon VE/7000 QY (AGP), ATI Radeon VE/7000 QZ (AGP),
ATI Radeon Mobility M7 LW (AGP),
ATI Mobility FireGL 7800 M7 LX (AGP),
ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
ATI Radeon IGP320 (A3) 4136, ATI Radeon IGP320M (U1) 4336,
ATI Radeon IGP330/340/350 (A4) 4137,
ATI Radeon IGP330M/340M/350M (U2) 4337,
ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QI (AGP),
ATI Radeon 8500 QJ (AGP), ATI Radeon 8500 QK (AGP),
ATI Radeon 8500 QL (AGP), ATI Radeon 9100 QM (AGP),
ATI Radeon 8500 QN (AGP), ATI Radeon 8500 QO (AGP),
ATI Radeon 8500 Qh (AGP), ATI Radeon 8500 Qi (AGP),
ATI Radeon 8500 Qj (AGP), ATI Radeon 8500 Qk (AGP),
ATI Radeon 8500 Ql (AGP), ATI Radeon 8500 BB (AGP),
ATI Radeon 7500 QW (AGP), ATI Radeon 7500 QX (AGP),
ATI Radeon 9000 Id (AGP), ATI Radeon 9000 Ie (AGP),
ATI Radeon 9000 If (AGP), ATI Radeon 9000 Ig (AGP),
ATI Radeon Mobility M9 Ld (AGP), ATI Radeon Mobility M9 Le (AGP),
ATI Radeon Mobility M9 Lf (AGP), ATI Radeon Mobility M9 Lg (AGP),
ATI Radeon 9200 5960 (AGP), ATI Radeon 9200 5961 (AGP),
ATI Radeon 9200 5962 (AGP), ATI Radeon 9200 5963 (AGP),
ATI Radeon M9+ 5968 (AGP), ATI Radeon M9+ 5969 (AGP),
ATI Radeon M9+ 596A (AGP), ATI Radeon M9+ 596B (AGP),
ATI Radeon 9500 AD (AGP), ATI Radeon 9500 AE (AGP),
ATI Radeon 9500 AF (AGP), ATI FireGL Z1/X1 AG (AGP),
ATI Radeon 9700 Pro ND (AGP), ATI Radeon 9700/9500Pro NE (AGP),
ATI Radeon 9700 NF (AGP), ATI FireGL X1 NG (AGP)
(II) Primary Device is: PCI 01:00:0
(--) Chipset ATI Rage 128 Pro GL PF (AGP) found
(--) Chipset ATI Rage 128 Pro GL PF (AGP) found
(II) Loading sub module "r128"
(II) LoadModule: "r128"
(II) Reloading /usr/X11R6/lib/modules/drivers/r128_drv.o
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xe4000000 - 0xe43fffff (0x400000) MX[B]
[6] -1 0 0xe4400000 - 0xe440ffff (0x10000) MX[B]
[7] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[8] -1 0 0xe1004000 - 0xe1007fff (0x4000) MX[B](B)
[9] -1 0 0xdc000000 - 0xdfffffff (0x4000000) MX[B](B)
[10] -1 0 0xe1000000 - 0xe1003fff (0x4000) MX[B](B)
[11] -1 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B](B)
[12] -1 0 0xe3000000 - 0xe3ffffff (0x1000000) MX[B](B)
[13] -1 0 0xe2000000 - 0xe2ffffff (0x1000000) MX[B](B)
[14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[15] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[16] -1 0 0x0000ec00 - 0x0000ec07 (0x8) IX[B]
[17] -1 0 0x0000e800 - 0x0000e81f (0x20) IX[B]
[18] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[19] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[20] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B](B)
[21] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[B](B)
(II) Loading sub module "r128"
(II) LoadModule: "r128"
(II) Reloading /usr/X11R6/lib/modules/drivers/r128_drv.o
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xe4000000 - 0xe43fffff (0x400000) MX[B]
[6] -1 0 0xe4400000 - 0xe440ffff (0x10000) MX[B]
[7] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[8] -1 0 0xe1004000 - 0xe1007fff (0x4000) MX[B](B)
[9] -1 0 0xdc000000 - 0xdfffffff (0x4000000) MX[B](B)
[10] -1 0 0xe1000000 - 0xe1003fff (0x4000) MX[B](B)
[11] -1 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B](B)
[12] -1 0 0xe3000000 - 0xe3ffffff (0x1000000) MX[B](B)
[13] -1 0 0xe2000000 - 0xe2ffffff (0x1000000) MX[B](B)
[14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[15] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[16] -1 0 0x0000ec00 - 0x0000ec07 (0x8) IX[B]
[17] -1 0 0x0000e800 - 0x0000e81f (0x20) IX[B]
[18] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[19] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[20] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B](B)
[21] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[B](B)
(II) resource ranges after probing:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xe4000000 - 0xe43fffff (0x400000) MX[B]
[6] -1 0 0xe4400000 - 0xe440ffff (0x10000) MX[B]
[7] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[8] -1 0 0xe1004000 - 0xe1007fff (0x4000) MX[B](B)
[9] -1 0 0xdc000000 - 0xdfffffff (0x4000000) MX[B](B)
[10] -1 0 0xe1000000 - 0xe1003fff (0x4000) MX[B](B)
[11] -1 0 0xd8000000 - 0xdbffffff (0x4000000) MX[B](B)
[12] -1 0 0xe3000000 - 0xe3ffffff (0x1000000) MX[B](B)
[13] -1 0 0xe2000000 - 0xe2ffffff (0x1000000) MX[B](B)
[14] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[15] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[16] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[17] 1 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[18] 1 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[19] 1 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[20] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[21] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[22] -1 0 0x0000ec00 - 0x0000ec07 (0x8) IX[B]
[23] -1 0 0x0000e800 - 0x0000e81f (0x20) IX[B]
[24] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[25] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[26] -1 0 0x0000d400 - 0x0000d4ff (0x100) IX[B](B)
[27] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[B](B)
[28] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[29] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
[30] 1 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[31] 1 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(II) Setting vga for screen 1.
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R6/lib/modules/libvgahw.a
(II) Module vgahw: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.6
(II) R128(0): PCI bus 1 card 0 func 0
(**) R128(0): Depth 16, (--) framebuffer bpp 16
(II) R128(0): Pixel depth = 16 bits stored in 2 bytes (16 bpp pixmaps)
(==) R128(0): Default visual is TrueColor
(==) R128(0): RGB weight 565
(II) R128(0): Using 6 bits per RGB (8 bit DAC)
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/X11R6/lib/modules/linux/libint10.a
(II) Module int10: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.6
(II) R128(0): initializing int10
(II) R128(0): Primary V_BIOS segment is: 0xc000
(--) R128(0): Chipset: "ATI Rage 128 Pro GL PF (AGP)" (ChipID = 0x5046)
(--) R128(0): Linear framebuffer at 0xd8000000
(--) R128(0): MMIO registers at 0xe1000000
(--) R128(0): VideoRAM: 32768 kByte (64-bit SDR SGRAM 1:1)
(**) R128(0): Using external CRT for display
(WW) R128(0): Can't determine panel dimensions, and none specified. Disabling programming of FP registers.
(II) R128(0): PLL parameters: rf=2700 rd=60 min=12500 max=40000; xclk=14300
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/X11R6/lib/modules/libddc.a
(II) Module ddc: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.0.0
ABI class: XFree86 Video Driver, version 0.6
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/X11R6/lib/modules/libvbe.a
(II) Module vbe: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.1.0
ABI class: XFree86 Video Driver, version 0.6
(II) R128(0): VESA BIOS detected
(II) R128(0): VESA VBE Version 2.0
(II) R128(0): VESA VBE Total Mem: 32768 kB
(II) R128(0): VESA VBE OEM: ATI RAGE128
(II) R128(0): VESA VBE OEM Software Rev: 1.0
(II) R128(0): VESA VBE OEM Vendor: ATI Technologies Inc.
(II) R128(0): VESA VBE OEM Product: R128
(II) R128(0): VESA VBE OEM Product Rev: 01.00
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Reloading /usr/X11R6/lib/modules/libddc.a
(II) R128(0): VESA VBE DDC supported
(II) R128(0): VESA VBE DDC Level 2
(II) R128(0): VESA VBE DDC transfer in appr. 2 sec.
(II) R128(0): VESA VBE DDC read successfully
(II) R128(0): Manufacturer: SAM Model: 27 Serial#: 1095643447
(II) R128(0): Year: 2002 Week: 51
(II) R128(0): EDID Version: 1.3
(II) R128(0): Analog Display Input, Input Voltage Level: 0.700/0.700 V
(II) R128(0): Sync: Separate
(II) R128(0): Max H-Image Size [cm]: horiz.: 32 vert.: 24
(II) R128(0): Gamma: 2.07
(II) R128(0): DPMS capabilities: Off; RGB/Color Display
(II) R128(0): First detailed timing is preferred mode
(II) R128(0): redX: 0.645 redY: 0.321 greenX: 0.285 greenY: 0.600
(II) R128(0): blueX: 0.142 blueY: 0.057 whiteX: 0.283 whiteY: 0.298
(II) R128(0): Supported VESA Video Modes:
(II) R128(0): 720x400@70Hz
(II) R128(0): 640x480@60Hz
(II) R128(0): 640x480@75Hz
(II) R128(0): Manufacturer's mask: 0
(II) R128(0): Supported Future Video Modes:
(II) R128(0): #0: hsize: 640 vsize 480 refresh: 60 vid: 16433
(II) R128(0): #1: hsize: 640 vsize 480 refresh: 85 vid: 22833
(II) R128(0): #2: hsize: 800 vsize 600 refresh: 85 vid: 22853
(II) R128(0): #3: hsize: 1024 vsize 768 refresh: 85 vid: 22881
(II) R128(0): #4: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) R128(0): Supported additional Video Mode:
(II) R128(0): clock: 94.5 MHz Image Size: 312 x 234 mm
(II) R128(0): h_active: 1024 h_sync: 1072 h_sync_end 1168 h_blank_end 1376 h_border: 0
(II) R128(0): v_active: 768 v_sync: 769 v_sync_end 772 v_blanking: 808 v_border: 0
(II) R128(0): Ranges: V min: 50 V max: 160 Hz, H min: 30 H max: 71 kHz, PixClock max 110 MHz
(II) R128(0): Monitor name: SyncMaster
(II) R128(0): Serial No: HSATC18061
(==) R128(0): Using gamma correction (1.0, 1.0, 1.0)
(==) R128(0): Write-combining range (0xd8000000,0x2000000)
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Loading /usr/X11R6/lib/modules/libi2c.a
(II) Module i2c: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.2.0
ABI class: XFree86 Video Driver, version 0.6
(II) R128(0): I2C bus "DDC" initialized.
(II) R128(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) R128(0): I2C device "DDC:ddc2" removed.
(EE) R128(0): No DFP detected
(II) R128(0): monitor1: Using hsync range of 30.00-71.00 kHz
(II) R128(0): monitor1: Using vrefresh range of 50.00-160.00 Hz
(II) R128(0): Clock range: 12.50 to 400.00 MHz
(II) R128(0): Not using default mode "1280x960" (hsync out of range)
(II) R128(0): Not using default mode "640x480" (hsync out of range)
(II) R128(0): Not using default mode "1280x1024" (hsync out of range)
(II) R128(0): Not using default mode "640x512" (hsync out of range)
(II) R128(0): Not using default mode "1280x1024" (hsync out of range)
(II) R128(0): Not using default mode "640x512" (hsync out of range)
(II) R128(0): Not using default mode "1600x1200" (hsync out of range)
(II) R128(0): Not using default mode "800x600" (hsync out of range)
(II) R128(0): Not using default mode "1600x1200" (hsync out of range)
(II) R128(0): Not using default mode "800x600" (hsync out of range)
(II) R128(0): Not using default mode "1600x1200" (hsync out of range)
(II) R128(0): Not using default mode "800x600" (hsync out of range)
(II) R128(0): Not using default mode "1600x1200" (hsync out of range)
(II) R128(0): Not using default mode "800x600" (hsync out of range)
(II) R128(0): Not using default mode "1600x1200" (hsync out of range)
(II) R128(0): Not using default mode "800x600" (hsync out of range)
(II) R128(0): Not using default mode "1792x1344" (hsync out of range)
(II) R128(0): Not using default mode "896x672" (hsync out of range)
(II) R128(0): Not using default mode "1792x1344" (hsync out of range)
(II) R128(0): Not using default mode "896x672" (hsync out of range)
(II) R128(0): Not using default mode "1856x1392" (hsync out of range)
(II) R128(0): Not using default mode "928x696" (hsync out of range)
(II) R128(0): Not using default mode "1856x1392" (hsync out of range)
(II) R128(0): Not using default mode "928x696" (hsync out of range)
(II) R128(0): Not using default mode "1920x1440" (hsync out of range)
(II) R128(0): Not using default mode "960x720" (hsync out of range)
(II) R128(0): Not using default mode "1920x1440" (hsync out of range)
(II) R128(0): Not using default mode "960x720" (hsync out of range)
(WW) (1400x1050,monitor1) mode clock 122MHz exceeds DDC maximum 110MHz
(II) R128(0): Not using default mode "1400x1050" (hsync out of range)
(II) R128(0): Not using default mode "700x525" (hsync out of range)
(II) R128(0): Not using default mode "1920x1440" (hsync out of range)
(II) R128(0): Not using default mode "960x720" (hsync out of range)
(II) R128(0): Not using default mode "2048x1536" (hsync out of range)
(II) R128(0): Not using default mode "1024x768" (hsync out of range)
(II) R128(0): Not using default mode "2048x1536" (hsync out of range)
(II) R128(0): Not using default mode "1024x768" (hsync out of range)
(II) R128(0): Not using default mode "2048x1536" (hsync out of range)
(II) R128(0): Not using default mode "1024x768" (hsync out of range)
(II) R128(0): Not using default mode "1400x1050" (width too large for virtual size)
(II) R128(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) R128(0): Not using default mode "1280x960" (width too large for virtual size)
(II) R128(0): Not using default mode "1152x864" (width too large for virtual size)
(II) R128(0): Not using default mode "1152x768" (width too large for virtual size)
(--) R128(0): Virtual size is 1024x768 (pitch 1024)
(**) R128(0): *Default mode "1024x768": 94.5 MHz, 68.7 kHz, 85.0 Hz
(II) R128(0): Modeline "1024x768" 94.50 1024 1072 1168 1376 768 769 772 808 +hsync +vsync
(**) R128(0): *Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz
(II) R128(0): Modeline "800x600" 56.30 800 832 896 1048 600 601 604 631 +hsync +vsync
(**) R128(0): *Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz
(II) R128(0): Modeline "640x480" 36.00 640 696 752 832 480 481 484 509 -hsync -vsync
(**) R128(0): Default mode "1024x768": 78.8 MHz, 60.1 kHz, 75.1 Hz
(II) R128(0): Modeline "1024x768" 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
(**) R128(0): Default mode "1024x768": 75.0 MHz, 56.5 kHz, 70.1 Hz
(II) R128(0): Modeline "1024x768" 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
(**) R128(0): Default mode "1024x768": 65.0 MHz, 48.4 kHz, 60.0 Hz
(II) R128(0): Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
(**) R128(0): Default mode "1024x768": 44.9 MHz, 35.5 kHz, 87.1 Hz (I)
(II) R128(0): Modeline "1024x768" 44.90 1024 1032 1208 1264 768 768 776 817 interlace +hsync +vsync
(**) R128(0): Default mode "832x624": 57.3 MHz, 49.7 kHz, 74.6 Hz
(II) R128(0): Modeline "832x624" 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync
(**) R128(0): Mode "1024x480": 65.0 MHz, 48.4 kHz, 85.9 Hz
(II) R128(0): Modeline "1024x480" 65.00 1024 1032 1176 1344 480 488 494 563 -hsync -vsync
(**) R128(0): Default mode "800x600": 49.5 MHz, 46.9 kHz, 75.0 Hz
(II) R128(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync
(**) R128(0): Default mode "800x600": 50.0 MHz, 48.1 kHz, 72.2 Hz
(II) R128(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync
(**) R128(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz
(II) R128(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
(**) R128(0): Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz
(II) R128(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync
(**) R128(0): Mode "768x576": 63.1 MHz, 61.6 kHz, 100.0 Hz
(II) R128(0): Modeline "768x576" 63.07 768 800 960 1024 576 578 590 616
(**) R128(0): Mode "768x576": 50.0 MHz, 50.0 kHz, 79.4 Hz
(II) R128(0): Modeline "768x576" 50.00 768 832 846 1000 576 590 595 630
(**) R128(0): Default mode "700x525": 61.0 MHz, 64.9 kHz, 60.0 Hz (D)
(II) R128(0): Modeline "700x525" 61.00 700 744 820 940 525 526 532 541 doublescan +hsync +vsync
(**) R128(0): Default mode "640x512": 54.0 MHz, 64.0 kHz, 60.0 Hz (D)
(II) R128(0): Modeline "640x512" 54.00 640 664 720 844 512 512 514 533 doublescan +hsync +vsync
(**) R128(0): Default mode "640x480": 31.5 MHz, 37.5 kHz, 75.0 Hz
(II) R128(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync
(**) R128(0): Default mode "640x480": 31.5 MHz, 37.9 kHz, 72.8 Hz
(II) R128(0): Modeline "640x480" 31.50 640 664 704 832 480 489 491 520 -hsync -vsync
(**) R128(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz
(II) R128(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -hsync -vsync
(**) R128(0): Default mode "640x480": 54.0 MHz, 60.0 kHz, 60.0 Hz (D)
(II) R128(0): Modeline "640x480" 54.00 640 688 744 900 480 480 482 500 doublescan +hsync +vsync
(**) R128(0): Default mode "720x400": 35.5 MHz, 37.9 kHz, 85.0 Hz
(II) R128(0): Modeline "720x400" 35.50 720 756 828 936 400 401 404 446 -hsync +vsync
(**) R128(0): Default mode "640x400": 31.5 MHz, 37.9 kHz, 85.1 Hz
(II) R128(0): Modeline "640x400" 31.50 640 672 736 832 400 401 404 445 -hsync +vsync
(**) R128(0): Default mode "576x432": 54.0 MHz, 67.5 kHz, 75.0 Hz (D)
(II) R128(0): Modeline "576x432" 54.00 576 608 672 800 432 432 434 450 doublescan +hsync +vsync
(**) R128(0): Default mode "640x350": 31.5 MHz, 37.9 kHz, 85.1 Hz
(II) R128(0): Modeline "640x350" 31.50 640 672 736 832 350 382 385 445 +hsync -vsync
(**) R128(0): Default mode "576x384": 32.5 MHz, 44.2 kHz, 54.8 Hz (D)
(II) R128(0): Modeline "576x384" 32.50 576 589 657 736 384 385 388 403 doublescan +hsync +vsync
(**) R128(0): Default mode "512x384": 47.2 MHz, 68.7 kHz, 85.0 Hz (D)
(II) R128(0): Modeline "512x384" 47.25 512 536 584 688 384 384 386 404 doublescan +hsync +vsync
(**) R128(0): Default mode "512x384": 39.4 MHz, 60.1 kHz, 75.1 Hz (D)
(II) R128(0): Modeline "512x384" 39.40 512 520 568 656 384 384 386 400 doublescan +hsync +vsync
(**) R128(0): Default mode "512x384": 37.5 MHz, 56.5 kHz, 70.1 Hz (D)
(II) R128(0): Modeline "512x384" 37.50 512 524 592 664 384 385 388 403 doublescan -hsync -vsync
(**) R128(0): Default mode "512x384": 32.5 MHz, 48.4 kHz, 60.0 Hz (D)
(II) R128(0): Modeline "512x384" 32.50 512 524 592 672 384 385 388 403 doublescan -hsync -vsync
(**) R128(0): Default mode "512x384": 22.4 MHz, 35.5 kHz, 87.1 Hz (D)
(II) R128(0): Modeline "512x384" 22.45 512 516 604 632 384 384 388 409 interlace doublescan +hsync +vsync
(**) R128(0): Default mode "416x312": 28.6 MHz, 49.7 kHz, 74.7 Hz (D)
(II) R128(0): Modeline "416x312" 28.64 416 432 464 576 312 312 314 333 doublescan -hsync -vsync
(**) R128(0): Default mode "400x300": 28.1 MHz, 53.7 kHz, 85.3 Hz (D)
(II) R128(0): Modeline "400x300" 28.15 400 416 448 524 300 300 302 315 doublescan +hsync +vsync
(**) R128(0): Default mode "400x300": 24.8 MHz, 46.9 kHz, 75.1 Hz (D)
(II) R128(0): Modeline "400x300" 24.75 400 408 448 528 300 300 302 312 doublescan +hsync +vsync
(**) R128(0): Default mode "400x300": 25.0 MHz, 48.1 kHz, 72.2 Hz (D)
(II) R128(0): Modeline "400x300" 25.00 400 428 488 520 300 318 321 333 doublescan +hsync +vsync
(**) R128(0): Default mode "400x300": 20.0 MHz, 37.9 kHz, 60.3 Hz (D)
(II) R128(0): Modeline "400x300" 20.00 400 420 484 528 300 300 302 314 doublescan +hsync +vsync
(**) R128(0): Default mode "400x300": 18.0 MHz, 35.2 kHz, 56.3 Hz (D)
(II) R128(0): Modeline "400x300" 18.00 400 412 448 512 300 300 301 312 doublescan +hsync +vsync
(**) R128(0): Default mode "320x240": 18.0 MHz, 43.3 kHz, 85.2 Hz (D)
(II) R128(0): Modeline "320x240" 18.00 320 348 376 416 240 240 242 254 doublescan -hsync -vsync
(**) R128(0): Default mode "320x240": 15.8 MHz, 37.5 kHz, 75.0 Hz (D)
(II) R128(0): Modeline "320x240" 15.75 320 328 360 420 240 240 242 250 doublescan -hsync -vsync
(**) R128(0): Default mode "320x240": 15.8 MHz, 37.9 kHz, 72.8 Hz (D)
(II) R128(0): Modeline "320x240" 15.75 320 332 352 416 240 244 245 260 doublescan -hsync -vsync
(**) R128(0): Default mode "320x240": 12.6 MHz, 31.5 kHz, 60.1 Hz (D)
(II) R128(0): Modeline "320x240" 12.60 320 328 376 400 240 245 246 262 doublescan -hsync -vsync
(**) R128(0): Default mode "360x200": 17.8 MHz, 37.9 kHz, 85.0 Hz (D)
(II) R128(0): Modeline "360x200" 17.75 360 378 414 468 200 200 202 223 doublescan -hsync +vsync
(**) R128(0): Default mode "320x200": 15.8 MHz, 37.9 kHz, 85.3 Hz (D)
(II) R128(0): Modeline "320x200" 15.75 320 336 368 416 200 200 202 222 doublescan -hsync +vsync
(**) R128(0): Default mode "320x175": 15.8 MHz, 37.9 kHz, 85.3 Hz (D)
(II) R128(0): Modeline "320x175" 15.75 320 336 368 416 175 191 192 222 doublescan +hsync -vsync
(--) R128(0): Display dimensions: (320, 240) mm
(--) R128(0): DPI set to (81, 81)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules/libfb.a
(II) Module fb: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.0.0
ABI class: XFree86 ANSI C Emulation, version 0.2
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R6/lib/modules/libramdac.a
(II) Module ramdac: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 0.1.0
ABI class: XFree86 Video Driver, version 0.6
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R6/lib/modules/libxaa.a
(II) Module xaa: vendor="The XFree86 Project"
compiled for 4.3.0, module version = 1.1.0
ABI class: XFree86 Video Driver, version 0.6
(!!) R128(0): For information on using the multimedia capabilities
of this adapter, please see http://gatos.sf.net.
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Reloading /usr/X11R6/lib/modules/libvgahw.a
(II) R128(1): PCI bus 1 card 1 func 0
(**) R128(1): Depth 16, (--) framebuffer bpp 16
(II) R128(1): Pixel depth = 16 bits stored in 2 bytes (16 bpp pixmaps)
(==) R128(1): Default visual is TrueColor
(==) R128(1): RGB weight 565
(II) R128(1): Using 6 bits per RGB (8 bit DAC)
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/X11R6/lib/modules/linux/libint10.a
(II) R128(1): initializing int10
(II) Multi Device Card detected: [1:0:0][1:1:0]
(EE) R128(1): Cannot read V_BIOS
(--) R128(1): Chipset: "ATI Rage 128 Pro GL PF (AGP)" (ChipID = 0x5046)
(--) R128(1): Linear framebuffer at 0xdc000000
(--) R128(1): MMIO registers at 0xe1004000
(--) R128(1): VideoRAM: 0 kByte (64-bit SDR SGRAM 1:1)
(**) R128(1): Using external CRT for display
(II) Multi Device Card detected: [1:0:0][1:1:0]
(WW) R128(1): Video BIOS not detected in PCI space!
(WW) R128(1): Attempting to read Video BIOS from legacy ISA space!
(WW) R128(1): Can't determine panel dimensions, and none specified. Disabling programming of FP registers.
(II) R128(1): PLL parameters: rf=2700 rd=60 min=12500 max=40000; xclk=14300
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Reloading /usr/X11R6/lib/modules/libddc.a
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Reloading /usr/X11R6/lib/modules/libvbe.a
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Reloading /usr/X11R6/lib/modules/linux/libint10.a
(II) R128(1): initializing int10
(II) Multi Device Card detected: [1:0:0][1:1:0]
(EE) R128(1): Cannot read V_BIOS
(==) R128(1): Using gamma correction (1.0, 1.0, 1.0)

Fatal server error:
xf86MapPciMem: Could not mmap PCI memory [base=0xdc000000,hostbase=0xdc000000,size=0] (Invalid argument)


When reporting a problem related to a server crash, please send
the full server output, not just the last messages.
This can be found in the log file "/var/log/XFree86.0.log".
Please report problems to xfree86@xfree86.org.
nix.nix
28-08-2003, 14:00
Questa è la mia configurazione

Section "Module"
Load "dbe" # Double-Buffering Extension
Load "extmod"
Load "type1"
Load "speedo"
Load "freetype"
Load "glx" # 3D layer
Load "dri" # direct rendering
EndSection

Section "DRI"
Mode 0666
EndSection

Section "Device"
Identifier "device1"
VendorName "ATI"
BoardName "ATI Rage 128"
Driver "r128"
Screen 0
BusID "PCI:1:0:0"
Option "DPMS"
Option "UseCCEFor2D" "false"
EndSection

Section "Device"
Identifier "device2"
VendorName "ATI"
BoardName "ATI Rage 128"
Driver "r128"
Screen 0
BusID "PCI:1:1:0"
Option "DPMS"
EndSection


agpgart : VIA Technologies|VT82C691 [Apollo PRO] [BRIDGE_HOST] (vendor:1106 device:0691)
unknown : VIA Technologies|VT82C598 [Apollo MVP3 AGP] [BRIDGE_PCI] (vendor:1106 device:8598)
unknown : VIA Technologies|VT82C596 ISA [Apollo PRO] [BRIDGE_ISA] (vendor:1106 device:0596 subv:1106 subd:0000)
unknown : VIA Technologies|VT82C586 IDE [Apollo] [STORAGE_IDE] (vendor:1106 device:0571)
usb-uhci : VIA Technologies|VT82C586B USB [SERIAL_USB] (vendor:1106 device:3038 subv:0925 subd:1234)
unknown : VIA Technologies Inc|Power Management Controller [BRIDGE_HOST] (vendor:1106 device:3051)
unknown : NEC|PowerVR PCX2 [midas] [MULTIMEDIA_OTHER] (vendor:1033 device:0046)
unknown : 3Dfx Interactive, Inc.|Voodoo 2 [MULTIMEDIA_VIDEO] (vendor:121a device:0002)
unknown : 3Dfx Interactive, Inc.|Voodoo 2 [MULTIMEDIA_VIDEO] (vendor:121a device:0002)
snd-emu10k1 : Creative Labs|SB Live! (audio) [MULTIMEDIA_AUDIO] (vendor:1102 device:0002 subv:1102 subd:8061)
emu10k1-gp : Creative Labs|SB Live! (joystick) [INPUT_OTHER] (vendor:1102 device:7002 subv:1102 subd:0020)
Card:ATI Rage 128: ATI|Rage 128 Pro AGP 4x [DISPLAY_VGA] (vendor:1002 device:5046 subv:1002 subd:2000)
Card:ATI Rage 128: ATI|Rage 128 Pro AGP 4x [DISPLAY_OTHER] (vendor:1002 device:5046 subv:1002 subd:2001)
unknown : Unknown|USB UHCI Root Hub [Hub|Root Hub] (vendor:0000 device:0000)

00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev 44)
Flags: bus master, medium devsel, latency 0
Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 1.0

00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: e0000000-e1ffffff
Prefetchable memory behind bridge: d8000000-dfffffff
Capabilities: [80] Power Management version 2

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C596 ISA [Mobile South] (rev 12)
Subsystem: VIA Technologies, Inc. VT82C596/A/B PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0

00:07.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 32
I/O ports at e000 [size=16]

00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 08) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at e400 [size=32]

00:07.3 Host bridge: VIA Technologies, Inc. VT82C596 Power Management (rev 20)
Flags: medium devsel

00:09.0 Multimedia controller: NEC Corporation PowerVR PCX2 [midas] (rev 01)
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 11
Memory at e4400000 (32-bit, prefetchable) [size=64K]
Memory at e4000000 (32-bit, prefetchable) [size=4M]

00:0b.0 Multimedia video controller: 3Dfx Interactive, Inc. Voodoo 2 (rev 02)
Flags: fast devsel
Memory at e2000000 (32-bit, prefetchable) [size=16M]

00:0f.0 Multimedia video controller: 3Dfx Interactive, Inc. Voodoo 2 (rev 02)
Flags: fast devsel
Memory at e3000000 (32-bit, prefetchable) [size=16M]

00:11.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07)
Subsystem: Creative Labs SBLive! Player 5.1
Flags: bus master, medium devsel, latency 32, IRQ 5
I/O ports at e800 [size=32]
Capabilities: [dc] Power Management version 1

00:11.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 07)
Subsystem: Creative Labs Gameport Joystick
Flags: bus master, medium devsel, latency 32
I/O ports at ec00 [size=8]
Capabilities: [dc] Power Management version 1

01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 PF/PRO AGP 4x TMDS (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Rage Fury MAXX AGP 4x (TMDS) (VGA device)
Flags: bus master, VGA palette snoop, stepping, 66Mhz, medium devsel, latency 32, IRQ 11
Memory at d8000000 (32-bit, prefetchable) [size=64M]
I/O ports at d000 [size=256]
Memory at e1000000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [50] AGP version 2.0
Capabilities: [5c] Power Management version 2

01:01.0 Display controller: ATI Technologies Inc Rage 128 PF/PRO AGP 4x TMDS
Subsystem: ATI Technologies Inc Rage Fury MAXX AGP 4x (TMDS) (Extra device?!)
Flags: bus master, stepping, 66Mhz, medium devsel, latency 32, IRQ 10
Memory at dc000000 (32-bit, prefetchable) [size=64M]
I/O ports at d400 [size=256]
Memory at e1004000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [50] AGP version 2.0
Capabilities: [5c] Power Management version 2
possi
28-08-2003, 17:04
Hai fatto quello che ti o detto sopra?
nix.nix
28-08-2003, 17:13
Originariamente inviato da possi
Hai fatto quello che ti o detto sopra?


:D Non ancora proverò stasera ma ho già provato con xf86cfg che non riesce neanche ha partire, la mia paura è che non abbia i driver

Ciao
Fabio Erculiani
28-08-2003, 17:19
se te lo risolvo cosa mi dai :) ?

IMHO devi impostare il VIDEO BIOS SHADOW su Enabled, nel bios....


se ti va mi offri una birra :) ?
Fabio Erculiani
28-08-2003, 17:23
altrimenti utilizza il driver generico "vesa"
nix.nix
28-08-2003, 22:44
Originariamente inviato da Fabio Erculiani

nell/ XF86Config-4
Driver "vesa"
Lascia inalterato il resto, e partirai con il driver vesa standard.



Innanzitutto chiedo scusa per aver aperto un doppio 3D anche se credevo diverso l argomento,

dopodiche nell rimgraziare tutti quelli che mi hanno aiutato volevo evidenziare per tutti coloro che dovessero avere problemii con la configuraze automatica dell XSERVE la soluzione sopracitata

[QUOTE][se te lo risolvo cosa mi dai ?

IMHO devi impostare il VIDEO BIOS SHADOW su Enabled, nel bios....


se ti va mi offri una birra ?
[QUOTE][

Per il momento mi premeva riuscire a far partire KDE, ne riparleremo quando dovro abilitare il direct rendering per il 3D, faro un link a questa pagina per la nuova discussione, allora si che ti offriro anche una pinta da 25L,

cmq OK per la birra,

adesso comincio a lavorare per gli ECIadsl su modem usb 220

scusate la punteggiatura ma vi scrivo da un RS/6000 RISC-AIX con tastiera americana

Ciao a tutti e grazie
:sofico: :sofico: :sofico:
Fabio Erculiani
29-08-2003, 09:07
:D
Io proverei a dare una controllata a:
cd /usr/src/linux
make menuconfig
nella sezione Video, guarda se è abilitato il supporto x la tua scheda video.
altrimenti abilitalo o con * (statico nel kernel, precaricato all'avvio) o con M (come modulo, da caricare con modprobe nomemodulo).

poi salvi ed esci e fai un bel:
make dep
make bzImage
make modules
make modules_install
make install
e copi il file arch/i386/boot/bzImage al posto del tuo attuale file vmlinuz.
ilsensine
29-08-2003, 09:21
Originariamente inviato da Fabio Erculiani
Io proverei a dare una controllata a:
cd /usr/src/linux
make menuconfig
nella sezione Video, guarda se è abilitato il supporto x la tua scheda video.

XFree richiede l'aiuto del kernel solo per l'accelerazione 3d. Per tutte le altre operazioni, è completamente indipendente dal kernel.
Fabio Erculiani
29-08-2003, 09:39
ciaohttp://www.amdplanet.it/fabio/drm-r128.png
ilsensine
29-08-2003, 09:50
Le voci sopra DRM sono per il supporto agp, quelle sotto sono per il supporto accelerato 3d. Entrambe non sono richieste per il normale funzionamento 2d.
Fabio Erculiani
29-08-2003, 10:50
io comunque le abiliterei ;)... altro non saprei
ilsensine
29-08-2003, 10:54
Sì sì certo, però non sono l'origine del problema. Visto che il problema è alquanto interessante, andrebbe riportato agli sviluppatori, e sarebbe bene farlo con la "minima configurazione non funzionante"

nix.nix, puoi provare ad avviare la macchina solo con la scheda ATI e rimuovendo momentaneamente le altre?
nix.nix
29-08-2003, 14:30
Si certo non è un problema se puoi aiutarmi a contattare gli sviluppatori, sai a scrivere in inglese sono un disastro!

fammi pure un elenco di tutti i file e i log che ti servono, devo ancora configurare il mio Ericsson hm220dp su porta USB, (se hai un buona guida per questo modem:D) i log che ti ho mostrato ho dovuto copiarli su floppy.

Non mi dispiacerebbe chiedere agli sviluppatori cosa si può fare per le Voodoo2 e la Matrox M3D con chip PowerVR PCX2
ilsensine
29-08-2003, 15:06
Per la v2 c'è un thread in giro che ne parla, per la PowerVR scordatelo.

Riguardo il report, visto che ti da lo stesso problema con diverse distribuzioni, forse il posto giusto per scrivere è direttamente alle mailing list di xfree. Ti consiglio di rimuovere le altre schede video dal sistema; i log che ti servono sono i messaggi del kernel (dmesg), i messaggi di xfree (sotto /var/log), una descrizione del tuo hw (caratteristiche della scheda video, e lspci -nv), il file di configurazione di xfree. Ti consiglio di mettere questi file su uno spazio web e postare i link, senza appesantire troppo la mail. Specifica che si tratta di un problema che si presenta con più distribuzioni, altrimenti crederanno che è un problema specifico dell'xfree della Mandrake.
Puoi iniziare a scrivere qui:
http://www.xfree86.org/mailman/listinfo/xfree86/
e, se nessuno ti risponde, puoi provare con la ml degli sviluppatori.

Per curiosità, staccando le altre schede e tentando un X -configure cambia qualcosa?