RAID 0 & win98se,,,,come si parte????

[emax81]

Hola!

Ho un adaptec ATA RAID 1200A

http://graphics.adaptec.com/ata1200a.jpg


sul quale ho creato un array in modalità MIRROR ( su 2 wd jb 40 gb)....

....fin qua la solita minestra,,,ma adesso viene il bello,,,,

come si fà a partire con l'installazione di un win98se???? :muro: :muro:

con nt4/2k/xp basta premere F6 durante l'installazione,,,, e x w98???

Ciao e Grazie

[emax81]

qua trovate il manuale

http://graphics.adaptec.com/pdfs/installation_guides/ata_raid_1200a_iug_1.pdf
;)

[emax81]

Originally posted by "emax81"

qua trovate il manuale

http://graphics.adaptec.com/pdfs/installation_guides/ata_raid_1200a_iug_1.pdf
;)

ed al capitolo 4-2 , 4-3 c'è la speigazione :D


4-2
Installing the Device Driver for Windows 98

Installing the Driver When Installing Windows 98
Before you begin to install Windows 98, you will need the driver
floppy disk supplied with your Adaptec ATA RAID 1200A
controller kit.

When installing Windows 98 on a hard disk drive or an array
attached to the Adaptec ATA RAID 1200A, connect only the hard
disk drive or array that you intend to use as the Windows 98 boot
drive.
To install the driver when installing Windows 98, follow these
steps:

1 Install Windows 98 completely on drives or arrays attached to
the Adaptec ATA RAID 1200A before installing the driver.

2 Select Start from the task bar, then select Settings and Control
Panel.

3 Double-click the System icon, then select the Device Manager
tab.

4 Select Other devices, then PCI Mass Storage Controller.

5 Select Properties, then select the General tab.

6 Select Reinstall Driver and follow the Update Device Driver
Wizard.

7 On the Wizard searches for update drivers for PCI Mass
Storage Controller window, click Next.

8 Select Search for a better driver than the one your device is
using now and click Next.

9 On the Windows will now search for new drivers screen, make
sure a checkmark only appears next to specify location. Insert
the Adaptec ATA RAID 1200A floppy disk into the floppy disk
drive and type the following path as the location, then click
Next.
a:\win98_me
Installing the Device Driver

10 You will get this message:
Windows is now ready to install the best driver for this device...
Click Next.

11 After completing the installation, select Finish.

12 You will be prompted to restart the computer. Select Yes.

Installing the Driver When Windows 98 is Already Installed
To install the Adaptec ATA RAID 1200A driver if Windows 98 is
already installed, follow these steps:

1 Start Windows 98.
Windows 98 will automatically discover the new hardware and
start the Found New Hardware Wizard to guide you through
the device driver installation.

2 On the Add New Hardware Wizard window, select Next.

3 Select Search for the best driver for your device and click Next.

4 On the Windows will now search for new drivers screen, make
sure only a checkmark appears next to Specify Location. Insert
the Adaptec ATA RAID 1200A floppy disk into the floppy disk
drive. Type the following path as the location, then click Next:
a:\win98_me

5 The following message appears:
Windows is now ready to install the best driver for this device...
Click Next.

6 After completing the installation, select Finish.

7 The Adaptec RCM device is detected and the driver is
automatically loaded. Installation is now complete.

[MadMax_2000]

prova a guardare nelle discussioni in rilievo, trovi molte info sul raid...

ciauz :p