cover2
11-04-2014, 23:14
Modello notebook Aspire 3935.
Il touchpad ultimamente si bloccava. Ho smontato il notebook per alcune operazioni di manutenzione e sostituzione, ma al riassemblaggio, il touchpad non funzionava più. Ho provveduto a verificare le connessioni e sono in regola. Dal bios, non c'è modo di fare la diagnostica. Il sistema non lo vede.
Non è semplice individuare la causa esatta. L'upper-case funziona per quanto riguarda l'audio, microfono ecc... il finger print e touchpad no. Questi hanno un circuitino a parte. Vorrei escludere un problema ai connettori sulla scheda madre.
Ho cercato di caricare Ubuntu per escludere un problema di natura software, ma con esito negativo. Carica per molto tempo senza alcun effetto.
Acer ha pubblicato la procedura di diagnostica:
"1. After rebooting, run the Tracking Pad PS2 Mode Driver. For example Syn
touch driver.
2. Run the utility with the PS/2 mouse function and check if the mouse is
working.
3. If the PS/2 mouse does not work, then click if the main board to switch
board FPC is connected properly.
4. If the mainboard to switch board FPC is connected correctly, then check
if the FFC on the touchpad board is connected properly.
5. If the FFC on the touchpad board is connected correctly, check if LS851
JP1 Pin6 = 5V
are pules. If yes, then replace switch board. If not, then go to the next
step.
6. Replace the touchpad board.
7. If the touchpad still does not work, then replace the FPC on touchpad
board. After you use the touchpad, the pointer drifts on the screen for a
short time. This self-acting pointer movement will occur when a slight,
steady pressure is applied to the touchpad pointer. This symptom is not a
hardware problem. No actions are necessary to be taken if the pointer
movement stops in a short period of time.""
Vorrei effettuare la prova elettrica e in sicurezza, ma come?
A parte smontare e rimontare completamente due notebook, non ho mai provveduto a fare prove di questo tipo.Spero che ci sia un esperto fra voi.
Penso sia un problema di natura hardware, ma vorrei capire la causa precisa.
Il connettore sul quale si inserisce il flat, ha 5 pin non sei.
Il touchpad ultimamente si bloccava. Ho smontato il notebook per alcune operazioni di manutenzione e sostituzione, ma al riassemblaggio, il touchpad non funzionava più. Ho provveduto a verificare le connessioni e sono in regola. Dal bios, non c'è modo di fare la diagnostica. Il sistema non lo vede.
Non è semplice individuare la causa esatta. L'upper-case funziona per quanto riguarda l'audio, microfono ecc... il finger print e touchpad no. Questi hanno un circuitino a parte. Vorrei escludere un problema ai connettori sulla scheda madre.
Ho cercato di caricare Ubuntu per escludere un problema di natura software, ma con esito negativo. Carica per molto tempo senza alcun effetto.
Acer ha pubblicato la procedura di diagnostica:
"1. After rebooting, run the Tracking Pad PS2 Mode Driver. For example Syn
touch driver.
2. Run the utility with the PS/2 mouse function and check if the mouse is
working.
3. If the PS/2 mouse does not work, then click if the main board to switch
board FPC is connected properly.
4. If the mainboard to switch board FPC is connected correctly, then check
if the FFC on the touchpad board is connected properly.
5. If the FFC on the touchpad board is connected correctly, check if LS851
JP1 Pin6 = 5V
are pules. If yes, then replace switch board. If not, then go to the next
step.
6. Replace the touchpad board.
7. If the touchpad still does not work, then replace the FPC on touchpad
board. After you use the touchpad, the pointer drifts on the screen for a
short time. This self-acting pointer movement will occur when a slight,
steady pressure is applied to the touchpad pointer. This symptom is not a
hardware problem. No actions are necessary to be taken if the pointer
movement stops in a short period of time.""
Vorrei effettuare la prova elettrica e in sicurezza, ma come?
A parte smontare e rimontare completamente due notebook, non ho mai provveduto a fare prove di questo tipo.Spero che ci sia un esperto fra voi.
Penso sia un problema di natura hardware, ma vorrei capire la causa precisa.
Il connettore sul quale si inserisce il flat, ha 5 pin non sei.