Menzoberranzan
05-03-2012, 13:59
Ciao ragazzi, vi incollo un post che ho riportato sul forum MSI (ma non ho ancora ricevuto risposta). E' in inglese semplice.
Riassumendo comunque:
1) prima di 2gg fa il mio E8500 viaggiava tranquillamente a 4512mhz.
2) Ho deciso di portare la memoria ad 8gb. Ho comprato delle ram supportate, installate, funzionanti ma niente più oc.
3) ho quindi rollback alla config. iniziale.
4) a questo punto ho detto: ok, proviamo a spingere la memoria, ho innalzato il ratio della ram (girava a 950, ho provato a 1066, incrementando un voltaggio).
Beh da questo momento in poi non riesco più ad entrare nel bios. Come potete vedere nel post allegato ho fatto di tutto senza successo...
Avete altri suggerimenti??
grazie,
Marco
Hi blazers,
I'm facing a big trouble after having overclocked my system. Basically pc won't boot. I'm not able to see first welcome screen nor enter into the bios screen anymore.
My spec:
MB: MSI X48C Platinum - Bios v7.5b1
CPU: INTEL E8500 3.16
RAM: CORSAIR CM3X2G1600C9DHX DDR3 2x2GB BUT ALSO TRIED WITH KVR1333D3N9/2G 2x2GB
PSU: CORSAIR 750W
VB: ATI 6950 TOXIC @ 6970
LAST WEEK PC STATUS
Worked like a charm as following:
Bios Settings
D.O.T. CONTROL --> DISABLED
INTEL EIST --> DISABLED
CPU FSB FREQUENCY --> 475
CPU RATIO --> 9.5
CPU FREQUENCY --> 4512.5
EXTREME MEMORY PROFILE --> DISABLED (N/A)
FSB/MEMORY RATIO --> 1:1.00
ADJUSTED DRAM FREQUENCY --> 950
PCI-E FREQUENCY --> 105
PCI FREQUENCY --> 33.3Mhz
AUTO DISABLE DIMM/PCI FREQ --> DISABLED
CPU VOLTAGE --> 1.50v
MEMORY VOLTAGE --> 1.71v
FSB TERMINATOR VOLTAGE --> 1.39v
NB VOLTAGE --> 1.52v
SB CORE/CPU PLL VOLTAGE --> 1.50v
CPU GTL REFERENCE VOLTAGE 1 --> AUTO
CPU GTL REFERENCE VOLTAGE 2 --> AUTO
MCH GTL REFERENCE VOLTAGE --> AUTO
DDR CHA REFERENCE VOLTAGE --> AUTO
DDR CHB REFERENCE VOLTAGE --> AUTO
MCH DDR REFERENCE VOLTAGE --> AUTO
SPREAD SPECTRUM --> DISABLED
ADVANCE DRAM CONFIGURATION
CONFIGURE DRAM TIMING BY SPD --> AUTO
1N/2N MEMORY TIMING --> AUTO
NOW "PC STATUS" - WON'T BOOT ANYMORE
I'll tell you the whole story.
1) Last week I decided to increase MEMORY from 4gb to 8gb. Lookin' at MSI tech spec. Kingston memories were fully supported so I bought them. They worked but I couldn't increase cpu speed as before so I decided to move back to previous setting (corsair modules + cpu overclock).
2) Moving back It worked again but I decided, keeping the previous BIOS settings, to increase the memory RATIO, that is RAM Frequency to 1066, increasing the MCH DDR Voltage to 1.42 (damned pointer got on a forum) without changing the DRAM configuration (still using AUTO). Well I think I made several mistakes: MCH Voltage, DRAM config as AUTO, without trying to specify fixed values.
After that I wasn't able to restart my pc anymore.
I've tried to:
1) CLEAR CMOS WITH BUTTON (KEEPING UNPLUGGED EVERY CABLE) --> NO WAY
2) REMOVE CMOS BATTERY FOR ALMOST A DAY (KEEPING UNPLUGGED EVERY CABLE) --> NO WAY
3) DISCONNECT EVERYTHING FROM THE MAIN BORD (HDs, VIDEO CARD) BUT THE MEMORY --> NO WAY
4) SWITCH MEMORY (FROM CORSAIR to KINGSTON) --> NO WAY
5) REMOVE TURBO CARDS FROM MEMORY SLOTS --> NO WAY
6) CONNECT MEMORIES TO DIFFERENT SLOTS (by default 2 & 5) --> NO WAY
7) CONNECT A SINGLE MEMORY STICK (everywhere, slot 2,3,5,6) --> NO WAY
I'm not able to hear any "healthy" beap. If I remove all memory sticks I hear 3 bips in a row but nothing else (the pc is stuck at the black screen).
If I keep memory the pc is stuck at the black screen. Sometimes after several manual restarts or changing the memory slot, the pc begin to restart by itself without end.
Now what is missing? Hope you can help me.
Thanks in advance
Marco
Riassumendo comunque:
1) prima di 2gg fa il mio E8500 viaggiava tranquillamente a 4512mhz.
2) Ho deciso di portare la memoria ad 8gb. Ho comprato delle ram supportate, installate, funzionanti ma niente più oc.
3) ho quindi rollback alla config. iniziale.
4) a questo punto ho detto: ok, proviamo a spingere la memoria, ho innalzato il ratio della ram (girava a 950, ho provato a 1066, incrementando un voltaggio).
Beh da questo momento in poi non riesco più ad entrare nel bios. Come potete vedere nel post allegato ho fatto di tutto senza successo...
Avete altri suggerimenti??
grazie,
Marco
Hi blazers,
I'm facing a big trouble after having overclocked my system. Basically pc won't boot. I'm not able to see first welcome screen nor enter into the bios screen anymore.
My spec:
MB: MSI X48C Platinum - Bios v7.5b1
CPU: INTEL E8500 3.16
RAM: CORSAIR CM3X2G1600C9DHX DDR3 2x2GB BUT ALSO TRIED WITH KVR1333D3N9/2G 2x2GB
PSU: CORSAIR 750W
VB: ATI 6950 TOXIC @ 6970
LAST WEEK PC STATUS
Worked like a charm as following:
Bios Settings
D.O.T. CONTROL --> DISABLED
INTEL EIST --> DISABLED
CPU FSB FREQUENCY --> 475
CPU RATIO --> 9.5
CPU FREQUENCY --> 4512.5
EXTREME MEMORY PROFILE --> DISABLED (N/A)
FSB/MEMORY RATIO --> 1:1.00
ADJUSTED DRAM FREQUENCY --> 950
PCI-E FREQUENCY --> 105
PCI FREQUENCY --> 33.3Mhz
AUTO DISABLE DIMM/PCI FREQ --> DISABLED
CPU VOLTAGE --> 1.50v
MEMORY VOLTAGE --> 1.71v
FSB TERMINATOR VOLTAGE --> 1.39v
NB VOLTAGE --> 1.52v
SB CORE/CPU PLL VOLTAGE --> 1.50v
CPU GTL REFERENCE VOLTAGE 1 --> AUTO
CPU GTL REFERENCE VOLTAGE 2 --> AUTO
MCH GTL REFERENCE VOLTAGE --> AUTO
DDR CHA REFERENCE VOLTAGE --> AUTO
DDR CHB REFERENCE VOLTAGE --> AUTO
MCH DDR REFERENCE VOLTAGE --> AUTO
SPREAD SPECTRUM --> DISABLED
ADVANCE DRAM CONFIGURATION
CONFIGURE DRAM TIMING BY SPD --> AUTO
1N/2N MEMORY TIMING --> AUTO
NOW "PC STATUS" - WON'T BOOT ANYMORE
I'll tell you the whole story.
1) Last week I decided to increase MEMORY from 4gb to 8gb. Lookin' at MSI tech spec. Kingston memories were fully supported so I bought them. They worked but I couldn't increase cpu speed as before so I decided to move back to previous setting (corsair modules + cpu overclock).
2) Moving back It worked again but I decided, keeping the previous BIOS settings, to increase the memory RATIO, that is RAM Frequency to 1066, increasing the MCH DDR Voltage to 1.42 (damned pointer got on a forum) without changing the DRAM configuration (still using AUTO). Well I think I made several mistakes: MCH Voltage, DRAM config as AUTO, without trying to specify fixed values.
After that I wasn't able to restart my pc anymore.
I've tried to:
1) CLEAR CMOS WITH BUTTON (KEEPING UNPLUGGED EVERY CABLE) --> NO WAY
2) REMOVE CMOS BATTERY FOR ALMOST A DAY (KEEPING UNPLUGGED EVERY CABLE) --> NO WAY
3) DISCONNECT EVERYTHING FROM THE MAIN BORD (HDs, VIDEO CARD) BUT THE MEMORY --> NO WAY
4) SWITCH MEMORY (FROM CORSAIR to KINGSTON) --> NO WAY
5) REMOVE TURBO CARDS FROM MEMORY SLOTS --> NO WAY
6) CONNECT MEMORIES TO DIFFERENT SLOTS (by default 2 & 5) --> NO WAY
7) CONNECT A SINGLE MEMORY STICK (everywhere, slot 2,3,5,6) --> NO WAY
I'm not able to hear any "healthy" beap. If I remove all memory sticks I hear 3 bips in a row but nothing else (the pc is stuck at the black screen).
If I keep memory the pc is stuck at the black screen. Sometimes after several manual restarts or changing the memory slot, the pc begin to restart by itself without end.
Now what is missing? Hope you can help me.
Thanks in advance
Marco