cartman86
24-04-2011, 12:00
la scheda video del mio iMac7,1 è la ATI Radeon HD 2600 Pro
L'HARDWARE TEST DI APPLE (test completo) riporta:
4SNS/1/40000000: TGOH-96.750
In un forum ho trovato questo che citava il manuale
"From the manual
4SNS/1/40000000:TG0H
GPU temperature sensor (located on back side of MLB/video card) is disconnected or faulty.
Verify that the two pin sensor cable is securely connected to the MLB. The connector is located on the back side of the MLB and requires removal of the MLB to access it. If it continues to fail the diagnostic replace the video card.
If the sensor is disconnected the CPU fan will run at full speed.
Check that the cable is not crimped/damaged causing short. Generally speaking, A high reading is typically symptomatic of a shorted sensor but an unplugged or open circuit sensor usually causes a fail-safe full fan speed in most applications.
I'd expect you should be able to get a replacement sensor without having to trash the entire VGA card, the other possibility is that there will be identifying numbers on the sensor housing that will allow you to buy another device from somewhere. I think it will be a fairly standard 3 wire device that is glued into the heatsink."
FONTE WEB
http://webcache.googleusercontent.co...=www.google.it
Ora io volevo capire se il sensore in questione appartiene alla scheda video (come mi sembra di aver capito) o alla scheda logica; non essendo io un tecnico, ma volendo andare a un centro assistenza apple sapendo cosa va cambiato (so benissimo che se è un problema della scheda logica è meglio acquistarne un altro...), volevo sapere se sostituendo la scheda video risolvo il problema.
Quello che mi ha spinto ad indagare è la velocità delle mie ventole, sempre al massimo, e un ronzio forte all'inizio (un'eccessiva accelerazione delle ventole presumo) che si attutisce solo in parecchi minuti;
inoltre le temperature della GPU...
monitorate da iStat
GPU 80° C
GPU diode 89° C
GPU Heatsink 85° C
Un'ultima domanda anche se forse non centra molto..
il power supply a 87° è normale?
Insomma ho le ventole sempre costantemente al massimo anche se uso Fan control... Ma, insomma c'è proprio scritto sopra
"If the sensor is disconnected the CPU fan will run at full speed."
Come devo agire?
L'HARDWARE TEST DI APPLE (test completo) riporta:
4SNS/1/40000000: TGOH-96.750
In un forum ho trovato questo che citava il manuale
"From the manual
4SNS/1/40000000:TG0H
GPU temperature sensor (located on back side of MLB/video card) is disconnected or faulty.
Verify that the two pin sensor cable is securely connected to the MLB. The connector is located on the back side of the MLB and requires removal of the MLB to access it. If it continues to fail the diagnostic replace the video card.
If the sensor is disconnected the CPU fan will run at full speed.
Check that the cable is not crimped/damaged causing short. Generally speaking, A high reading is typically symptomatic of a shorted sensor but an unplugged or open circuit sensor usually causes a fail-safe full fan speed in most applications.
I'd expect you should be able to get a replacement sensor without having to trash the entire VGA card, the other possibility is that there will be identifying numbers on the sensor housing that will allow you to buy another device from somewhere. I think it will be a fairly standard 3 wire device that is glued into the heatsink."
FONTE WEB
http://webcache.googleusercontent.co...=www.google.it
Ora io volevo capire se il sensore in questione appartiene alla scheda video (come mi sembra di aver capito) o alla scheda logica; non essendo io un tecnico, ma volendo andare a un centro assistenza apple sapendo cosa va cambiato (so benissimo che se è un problema della scheda logica è meglio acquistarne un altro...), volevo sapere se sostituendo la scheda video risolvo il problema.
Quello che mi ha spinto ad indagare è la velocità delle mie ventole, sempre al massimo, e un ronzio forte all'inizio (un'eccessiva accelerazione delle ventole presumo) che si attutisce solo in parecchi minuti;
inoltre le temperature della GPU...
monitorate da iStat
GPU 80° C
GPU diode 89° C
GPU Heatsink 85° C
Un'ultima domanda anche se forse non centra molto..
il power supply a 87° è normale?
Insomma ho le ventole sempre costantemente al massimo anche se uso Fan control... Ma, insomma c'è proprio scritto sopra
"If the sensor is disconnected the CPU fan will run at full speed."
Come devo agire?