cescoo78
15-06-2008, 14:30
questa è la mia...
General Information :
A0 : Empty
A1 : Empty
A2 : Empty
A0 (Bank0/1 ) : 8192 MB - DIMM
Information SPD EEPROM (A0) :
Manufacturer : Unspecified
Part Number : Unspecified
Serial Number : 40185015
Type : DDR-SDRAM PC-3200 (200 MHz) - [DDR-400]
Size : 1024 MB (2 rows, 4 banks)
Module Buffered : No
Module Registered : No
Module SLi Ready (EPP) : No
Width : 64-bit
Error Correction Capability : No
Max. Burst Length : 8
Refresh : Reduced (.5x)7.8 µs, Self Refresh
Voltage : SSTL 2.5v
Prefetch Buffer : 2-bit
Manufacture : Week 56 of 2005
Supported Frequencies : 133 MHz, 166 MHz, 200 MHz
CAS Latency (tCL) : 2 clocks @133 MHz, 2.5 clocks @166 MHz, 3 clocks @200 MHz
RAS to CAS (tRCD) : 2 clocks @133 MHz, 3 clocks @166 MHz, 3 clocks @200 MHz
RAS Precharge (tRP) : 2 clocks @133 MHz, 3 clocks @166 MHz, 3 clocks @200 MHz
Cycle Time (tRAS) : 6 clocks @133 MHz, 7 clocks @166 MHz, 8 clocks @200 MHz
Memory Controller Information :
Memory Controller : Standard, DIMM
Number of connectors : 3
Max. Module Size : 0 MB
Supported Speed : 70ns, 60ns, 50ns
Supported Voltages : 2.9v
Error Detection Method : 64-bit ECC
Error Correction Capability : None
Current/Supported Interleave : 1-way/1-way
questa è quella che vorrei comprare che dite?
1GB 128M x 64-Bit
DDR400 CL3 184-Pin DIMM
Description
This document describes S3PLUS’s 128M x 64 bits Double Data Rate 400 Synchronous
Dynamic RAM high density memory module . The product consists of sixteen 64M x 8
Bit ( 16M x 8-bit x 4 Bank) in TSOP package and a 2K EEPROM in 8-pin SOP package mounted on a 184-pin glass-epoxy substrate.
The electrical and mechanical specification
are as follows:
Features:
• Power supply: Vdd=Vddq= 2.6V±0.1V
• Double data rate architecture: two data transfers per clock cycle.
• Clock Cycle Time ( tCK ) 5ns ( min. ) / 10ns ( max. )
• Row Cycle Time ( tRC ) 55ns ( min. )
• Refresh Row Cycle Time ( tRFC ) 70ns ( min. )
• Row Active Time ( tRAS ) 40ns ( min. ) / 70,000ns ( max. )
• Power ( IDD0 ) 5.408W ( operating )
• UL Rating 94 V - 0
• Bidirectional, data strobe (DQS) is transmitted/received with data
• DLL aligns DQ and DQS transitions with CLK transitions edges of DQS
• Burst type – Sequential / Interleave (programmable)
• 8192 refresh cycles / 64ms (4 banks concurrent refresh)
• Auto refresh and Self refresh
• Serial presence detect with EEPROM
volevo sapere se sono compatibili xchè ho preso una volta la fregata che la ram non mi funziona sulla mia scheda madre... che dite??
entrambe sono s3+ 1 gb ddr a 400 mhz pc 3200....
sono simili le 2 ram?
General Information :
A0 : Empty
A1 : Empty
A2 : Empty
A0 (Bank0/1 ) : 8192 MB - DIMM
Information SPD EEPROM (A0) :
Manufacturer : Unspecified
Part Number : Unspecified
Serial Number : 40185015
Type : DDR-SDRAM PC-3200 (200 MHz) - [DDR-400]
Size : 1024 MB (2 rows, 4 banks)
Module Buffered : No
Module Registered : No
Module SLi Ready (EPP) : No
Width : 64-bit
Error Correction Capability : No
Max. Burst Length : 8
Refresh : Reduced (.5x)7.8 µs, Self Refresh
Voltage : SSTL 2.5v
Prefetch Buffer : 2-bit
Manufacture : Week 56 of 2005
Supported Frequencies : 133 MHz, 166 MHz, 200 MHz
CAS Latency (tCL) : 2 clocks @133 MHz, 2.5 clocks @166 MHz, 3 clocks @200 MHz
RAS to CAS (tRCD) : 2 clocks @133 MHz, 3 clocks @166 MHz, 3 clocks @200 MHz
RAS Precharge (tRP) : 2 clocks @133 MHz, 3 clocks @166 MHz, 3 clocks @200 MHz
Cycle Time (tRAS) : 6 clocks @133 MHz, 7 clocks @166 MHz, 8 clocks @200 MHz
Memory Controller Information :
Memory Controller : Standard, DIMM
Number of connectors : 3
Max. Module Size : 0 MB
Supported Speed : 70ns, 60ns, 50ns
Supported Voltages : 2.9v
Error Detection Method : 64-bit ECC
Error Correction Capability : None
Current/Supported Interleave : 1-way/1-way
questa è quella che vorrei comprare che dite?
1GB 128M x 64-Bit
DDR400 CL3 184-Pin DIMM
Description
This document describes S3PLUS’s 128M x 64 bits Double Data Rate 400 Synchronous
Dynamic RAM high density memory module . The product consists of sixteen 64M x 8
Bit ( 16M x 8-bit x 4 Bank) in TSOP package and a 2K EEPROM in 8-pin SOP package mounted on a 184-pin glass-epoxy substrate.
The electrical and mechanical specification
are as follows:
Features:
• Power supply: Vdd=Vddq= 2.6V±0.1V
• Double data rate architecture: two data transfers per clock cycle.
• Clock Cycle Time ( tCK ) 5ns ( min. ) / 10ns ( max. )
• Row Cycle Time ( tRC ) 55ns ( min. )
• Refresh Row Cycle Time ( tRFC ) 70ns ( min. )
• Row Active Time ( tRAS ) 40ns ( min. ) / 70,000ns ( max. )
• Power ( IDD0 ) 5.408W ( operating )
• UL Rating 94 V - 0
• Bidirectional, data strobe (DQS) is transmitted/received with data
• DLL aligns DQ and DQS transitions with CLK transitions edges of DQS
• Burst type – Sequential / Interleave (programmable)
• 8192 refresh cycles / 64ms (4 banks concurrent refresh)
• Auto refresh and Self refresh
• Serial presence detect with EEPROM
volevo sapere se sono compatibili xchè ho preso una volta la fregata che la ram non mi funziona sulla mia scheda madre... che dite??
entrambe sono s3+ 1 gb ddr a 400 mhz pc 3200....
sono simili le 2 ram?