mgiuliano
18-02-2008, 23:06
Salve a tutti! Posseggo un Asus A3AC che monta un HD da 60gb (FUJITSU MHV2060AT PL) e un banco da 512mb di RAM (DDR2-SDRAM PC2-4300 (266 MHz) - [DDR2-533])
Siccome ormai non mi basta più, ho deciso di potenziarlo sostituendo l'hd con uno da 160gb e di aggiungere un altro banco di RAM, questa volta, da 1gb in modo da avere 1,5 gb circa. Il problema che mi pongo è questo: girando un po' su ebay ho trovato diversi hd ovviamente da 2,5' ma non so se devo prendere un ATA/EIDE (da quanto ho letto sono la stessa cosa) o un SATA. Il mio portatile supporta entrambe? Da quanto ho capito vedendo un po' il mio dovrebbe essere un' ATA, ma non so se è possibile comunque montare un SATA. E poi volevo sapere se posso prendere un qualsiasi tipo di banco ram o deve essere per forza uguale (pc2 4300 533).
Spero d esser stato chiaro; se vi servono altre informazioni chiedete pure. Posto qui delle caratteristiche dell'HD e della RAM prese col programma PC Wizard:
General Information :
DIMM1 (RAS 0, RAS 1) : 512 (Double Bank)
DIMM2 : Empty
Information SPD EEPROM :
Manufacturer : Nanya Technology
Part Number : NT512T64UH8A1FN-37
Serial Number : C99B1851
Type : DDR2-SDRAM PC2-4300 (266 MHz) - [DDR2-533]
Format : SO-DIMM (67,6 x 3)
Size : 512 MB (2 ranks, 4 banks)
Module Buffered : No
Module Registered : No
Module SLi Ready (EPP) : No
Width : 64-bit
Error Correction Capability : No
Max. Burst Length : 8
Refresh : Reduced (.5x)7.8 µs, Self Refresh
Voltage : SSTL 1.8v
Prefetch Buffer : 4-bit
Manufacture : Week 46 of 2005
Supported Frequencies : 200 MHz, 266 MHz, 266 MHz
CAS Latency (tCL) : 3 clocks @200 MHz, 4 clocks @266 MHz, 5 clocks @266 MHz
RAS to CAS (tRCD) : 3 clocks @200 MHz, 4 clocks @266 MHz, 4 clocks @266 MHz
RAS Precharge (tRP) : 3 clocks @200 MHz, 4 clocks @266 MHz, 4 clocks @266 MHz
Cycle Time (tRAS) : 9 clocks @200 MHz, 12 clocks @266 MHz, 12 clocks @266 MHz
Min TRC : 12 clocks @200 MHz, 16 clocks @266 MHz, 16 clocks @266 MHz
Memory Controller Information :
Memory Controller : Standard, DIMM, SDRAM
Number of connectors : 2
Max. Module Size : 1024 MB
Max. Memory Size : 2048 MB
Supported Speed : 70ns, 60ns, 50ns
Supported Voltages : 3.3v
Error Detection Method : No
Error Correction Capability : None
Current/Supported Interleave : 1-way/1-way
-----------------------------------------------------------
General Information :
SMART : Version 1.1
Informations Hard Disk FUJITSU MHV2060AT PL :
IDE Channel : #1 - Master Drive
Model : FUJITSU MHV2060AT PL
Serial Number : NSA1T5B28JB0
Revision : 000000A0
Serial ATA : No
Support : ATA/ATAPI-7
Size : 60 GB
Cache : 8 192 KB
Multiple Sector : 16
IORDY : Yes
LBA Mode : Yes
DMA Mode : Yes
NCQ Mode : No
SCT Mode : Yes
DCO Mode : Yes
NV Cache : No
TCQ Mode : No
CFA Power Mode : No
SETMAX : Yes - Disabled
Multiword DMA Mode : 2
PIO Mode : PIO 4
UDMA Mode max. : 5 (ATA-100)
UDMA Mode Enabled : 5 (ATA-100)
SMART : Yes - Enabled
SMART Self-Test : Yes
AAM : Yes - Enabled
AAM Values : 254 - (recommended 254)
Write Cache : Yes
Streaming Mode : No
Power Management : Yes
APM Mode : Yes - Enabled
APM Level : 16512
PUIS Mode : Yes - Disabled
Security Mode : No
Trusted Computing : No
48-bit Address : No
Cylinders : 16383
Heads : 16
Sectors per Track : 63
SMART Information Disk FUJITSU MHV2060AT PL :
Health : 99% (estimated)
Performance : 99% (estimated)
Threshold Exceeding : No
Raw Read Error Rate (01) : 21F97 (Threshold : 046 - Worst : 100 - Max : 100)
Throughput Performance (02) : 60000 (Threshold : 030 - Worst : 100 - Max : 100)
Spin Up Time (03) : 00000 (Threshold : 025 - Worst : 100 - Max : 100)
Start/Stop Count (04) : 005D7 (Threshold : 000 - Worst : 099 - Max : 099)
Reallocated Sector Count (05) : 00000 (Threshold : 024 - Worst : 100 - Max : 100)
Seek Error Rate (07) : 007F9 (Threshold : 047 - Worst : 100 - Max : 100)
Seek Time Performance (08) : 00000 (Threshold : 019 - Worst : 100 - Max : 100)
Power On Hours Count (09) : 82209 (Threshold : 000 - Worst : 094 - Max : 094)
Spin Retry Count (0A) : 00000 (Threshold : 020 - Worst : 100 - Max : 100)
Power Cycle Count (0C) : 005CD (Threshold : 000 - Worst : 100 - Max : 100)
Power-Off Retract Count (C0) : 00033 (Threshold : 000 - Worst : 100 - Max : 100)
Load/Unload Cycle Count (C1) : 0C021 (Threshold : 000 - Worst : 098 - Max : 098)
Temperature (C2) : 10029 (Threshold : 000 - Worst : 100 - Max : 100)
Hardware ECC Recovered (C3) : 02657 (Threshold : 000 - Worst : 100 - Max : 100)
Reallocation Event Count (C4) : 10000 (Threshold : 000 - Worst : 100 - Max : 100)
Current Pending Sector Count (C5) : 00000 (Threshold : 000 - Worst : 100 - Max : 100)
Off-Line Uncorrectable Sector Cou... 00000 (Threshold : 000 - Worst : 100 - Max : 100)
Ultra ATA CRC Error Rate (C7) : 00000 (Threshold : 000 - Worst : 200 - Max : 200)
Write Error Rate (C8) : 02EEC (Threshold : 060 - Worst : 100 - Max : 100)
(CB) : 004A0 (Threshold : 000 - Worst : 100 - Max : 100)
Partitions :
Hard Disk #1 : Partition #1 (1 GB)
Hard Disk #1 : Partition #2 (32 GB)
Hard Disk #1 : Partition #3 (21 GB)
Monitoring Information :
FUJITSU MHV2060AT PL : 41 °C
---------------------------------------------------------------------
grazie a tutti coloro che mi risponderanno.
Siccome ormai non mi basta più, ho deciso di potenziarlo sostituendo l'hd con uno da 160gb e di aggiungere un altro banco di RAM, questa volta, da 1gb in modo da avere 1,5 gb circa. Il problema che mi pongo è questo: girando un po' su ebay ho trovato diversi hd ovviamente da 2,5' ma non so se devo prendere un ATA/EIDE (da quanto ho letto sono la stessa cosa) o un SATA. Il mio portatile supporta entrambe? Da quanto ho capito vedendo un po' il mio dovrebbe essere un' ATA, ma non so se è possibile comunque montare un SATA. E poi volevo sapere se posso prendere un qualsiasi tipo di banco ram o deve essere per forza uguale (pc2 4300 533).
Spero d esser stato chiaro; se vi servono altre informazioni chiedete pure. Posto qui delle caratteristiche dell'HD e della RAM prese col programma PC Wizard:
General Information :
DIMM1 (RAS 0, RAS 1) : 512 (Double Bank)
DIMM2 : Empty
Information SPD EEPROM :
Manufacturer : Nanya Technology
Part Number : NT512T64UH8A1FN-37
Serial Number : C99B1851
Type : DDR2-SDRAM PC2-4300 (266 MHz) - [DDR2-533]
Format : SO-DIMM (67,6 x 3)
Size : 512 MB (2 ranks, 4 banks)
Module Buffered : No
Module Registered : No
Module SLi Ready (EPP) : No
Width : 64-bit
Error Correction Capability : No
Max. Burst Length : 8
Refresh : Reduced (.5x)7.8 µs, Self Refresh
Voltage : SSTL 1.8v
Prefetch Buffer : 4-bit
Manufacture : Week 46 of 2005
Supported Frequencies : 200 MHz, 266 MHz, 266 MHz
CAS Latency (tCL) : 3 clocks @200 MHz, 4 clocks @266 MHz, 5 clocks @266 MHz
RAS to CAS (tRCD) : 3 clocks @200 MHz, 4 clocks @266 MHz, 4 clocks @266 MHz
RAS Precharge (tRP) : 3 clocks @200 MHz, 4 clocks @266 MHz, 4 clocks @266 MHz
Cycle Time (tRAS) : 9 clocks @200 MHz, 12 clocks @266 MHz, 12 clocks @266 MHz
Min TRC : 12 clocks @200 MHz, 16 clocks @266 MHz, 16 clocks @266 MHz
Memory Controller Information :
Memory Controller : Standard, DIMM, SDRAM
Number of connectors : 2
Max. Module Size : 1024 MB
Max. Memory Size : 2048 MB
Supported Speed : 70ns, 60ns, 50ns
Supported Voltages : 3.3v
Error Detection Method : No
Error Correction Capability : None
Current/Supported Interleave : 1-way/1-way
-----------------------------------------------------------
General Information :
SMART : Version 1.1
Informations Hard Disk FUJITSU MHV2060AT PL :
IDE Channel : #1 - Master Drive
Model : FUJITSU MHV2060AT PL
Serial Number : NSA1T5B28JB0
Revision : 000000A0
Serial ATA : No
Support : ATA/ATAPI-7
Size : 60 GB
Cache : 8 192 KB
Multiple Sector : 16
IORDY : Yes
LBA Mode : Yes
DMA Mode : Yes
NCQ Mode : No
SCT Mode : Yes
DCO Mode : Yes
NV Cache : No
TCQ Mode : No
CFA Power Mode : No
SETMAX : Yes - Disabled
Multiword DMA Mode : 2
PIO Mode : PIO 4
UDMA Mode max. : 5 (ATA-100)
UDMA Mode Enabled : 5 (ATA-100)
SMART : Yes - Enabled
SMART Self-Test : Yes
AAM : Yes - Enabled
AAM Values : 254 - (recommended 254)
Write Cache : Yes
Streaming Mode : No
Power Management : Yes
APM Mode : Yes - Enabled
APM Level : 16512
PUIS Mode : Yes - Disabled
Security Mode : No
Trusted Computing : No
48-bit Address : No
Cylinders : 16383
Heads : 16
Sectors per Track : 63
SMART Information Disk FUJITSU MHV2060AT PL :
Health : 99% (estimated)
Performance : 99% (estimated)
Threshold Exceeding : No
Raw Read Error Rate (01) : 21F97 (Threshold : 046 - Worst : 100 - Max : 100)
Throughput Performance (02) : 60000 (Threshold : 030 - Worst : 100 - Max : 100)
Spin Up Time (03) : 00000 (Threshold : 025 - Worst : 100 - Max : 100)
Start/Stop Count (04) : 005D7 (Threshold : 000 - Worst : 099 - Max : 099)
Reallocated Sector Count (05) : 00000 (Threshold : 024 - Worst : 100 - Max : 100)
Seek Error Rate (07) : 007F9 (Threshold : 047 - Worst : 100 - Max : 100)
Seek Time Performance (08) : 00000 (Threshold : 019 - Worst : 100 - Max : 100)
Power On Hours Count (09) : 82209 (Threshold : 000 - Worst : 094 - Max : 094)
Spin Retry Count (0A) : 00000 (Threshold : 020 - Worst : 100 - Max : 100)
Power Cycle Count (0C) : 005CD (Threshold : 000 - Worst : 100 - Max : 100)
Power-Off Retract Count (C0) : 00033 (Threshold : 000 - Worst : 100 - Max : 100)
Load/Unload Cycle Count (C1) : 0C021 (Threshold : 000 - Worst : 098 - Max : 098)
Temperature (C2) : 10029 (Threshold : 000 - Worst : 100 - Max : 100)
Hardware ECC Recovered (C3) : 02657 (Threshold : 000 - Worst : 100 - Max : 100)
Reallocation Event Count (C4) : 10000 (Threshold : 000 - Worst : 100 - Max : 100)
Current Pending Sector Count (C5) : 00000 (Threshold : 000 - Worst : 100 - Max : 100)
Off-Line Uncorrectable Sector Cou... 00000 (Threshold : 000 - Worst : 100 - Max : 100)
Ultra ATA CRC Error Rate (C7) : 00000 (Threshold : 000 - Worst : 200 - Max : 200)
Write Error Rate (C8) : 02EEC (Threshold : 060 - Worst : 100 - Max : 100)
(CB) : 004A0 (Threshold : 000 - Worst : 100 - Max : 100)
Partitions :
Hard Disk #1 : Partition #1 (1 GB)
Hard Disk #1 : Partition #2 (32 GB)
Hard Disk #1 : Partition #3 (21 GB)
Monitoring Information :
FUJITSU MHV2060AT PL : 41 °C
---------------------------------------------------------------------
grazie a tutti coloro che mi risponderanno.