Arael
09-12-2007, 09:38
Allora ho 4 Moduli Ram in Dual Channel, tutti da 512 e tutti da 400 Mhz (SICURO).
Ecco i valori CAS di CPU-z:
DIMM #1 e 2
General
Memory type DDR
Manufacturer (ID) (0000000000000000)
Size 512 MBytes
Max bandwidth PC3200 (200 MHz)
Part number
Attributes
Number of banks 2
Data width 64 bits
Correction None
Registered no
Buffered no
Nominal Voltage 2.50 Volts
EPP no
XMP no
Timings table
Frequency (MHz) 166 200
CAS# 2.5 3.0
RAS# to CAS# delay 4 4
RAS# Precharge 4 4
TRAS 7 8
Questi 2 Banchi hanno CAS 166 Mhz = 2.5 e 200 Mhz = 3
DIMM #3 e 4
General
Memory type DDR
Manufacturer (ID) (0000000000000000)
Size 512 MBytes
Max bandwidth PC3200 (200 MHz)
Part number
Attributes
Number of banks 2
Data width 64 bits
Correction None
Registered no
Buffered no
Nominal Voltage 2.50 Volts
EPP no
XMP no
Timings table
Frequency (MHz) 200
CAS# 2.5
RAS# to CAS# delay 3
RAS# Precharge 3
TRAS 8
Questi 2 Banchi hanno CAS 200 Mhz = 2.5
Ora per incompatibilità di CAS le Ram si settano sul valore più basso (2.5) ma fanno viaggiare 2 dei 4 banchi a 166 MHz in questo modo, abbassando anche le frequenze degli altri.
Ora mi chiedo se posso mettere da Bios il CAS a 3 cosi che vadano a 200 Mhz (alzandolo quindi non abbassandolo) e sapere se corro rischi in questo modo.
Thx.
Ecco i valori CAS di CPU-z:
DIMM #1 e 2
General
Memory type DDR
Manufacturer (ID) (0000000000000000)
Size 512 MBytes
Max bandwidth PC3200 (200 MHz)
Part number
Attributes
Number of banks 2
Data width 64 bits
Correction None
Registered no
Buffered no
Nominal Voltage 2.50 Volts
EPP no
XMP no
Timings table
Frequency (MHz) 166 200
CAS# 2.5 3.0
RAS# to CAS# delay 4 4
RAS# Precharge 4 4
TRAS 7 8
Questi 2 Banchi hanno CAS 166 Mhz = 2.5 e 200 Mhz = 3
DIMM #3 e 4
General
Memory type DDR
Manufacturer (ID) (0000000000000000)
Size 512 MBytes
Max bandwidth PC3200 (200 MHz)
Part number
Attributes
Number of banks 2
Data width 64 bits
Correction None
Registered no
Buffered no
Nominal Voltage 2.50 Volts
EPP no
XMP no
Timings table
Frequency (MHz) 200
CAS# 2.5
RAS# to CAS# delay 3
RAS# Precharge 3
TRAS 8
Questi 2 Banchi hanno CAS 200 Mhz = 2.5
Ora per incompatibilità di CAS le Ram si settano sul valore più basso (2.5) ma fanno viaggiare 2 dei 4 banchi a 166 MHz in questo modo, abbassando anche le frequenze degli altri.
Ora mi chiedo se posso mettere da Bios il CAS a 3 cosi che vadano a 200 Mhz (alzandolo quindi non abbassandolo) e sapere se corro rischi in questo modo.
Thx.