View Full Version : portatile e problema con usb
ciao a tutti,
e' il mio primo post, cosi' ne approfitto per salutare tutti i membri del forum
ho poca esperienza e ho installato da poco ubuntu su una partizione del mio portatile (fujitsu-siemens) e funziona tutto a dovere a parte le periferiche sulla porta usb: questo sia se monto una pen (kingston) sia con qualsiasi altra periferica
vi posto i messaggi che vedo a terminale con lsusb e dmesg
lsusb:
Message from syslogd@amilo at ......
amilo kernel: [ 343.456000] Disabling IRQ #9
dmesg:
handlers:
[<c020c6a7>] (acpi_irq+0x0/0x14)
Disabling IRQ #9
ho cercato in rete e (per quel poco che ho capito) dovrei intervenire sull'acpi, ma come? nel bios non esistono opzioni
spero di risolvere col vostro aiuto perche' non so proprio come fare :doh:
saluti
gianlucab70
04-09-2007, 22:23
Ciao, ....:confused: ma prima di installare Ubuntu,con il vecchio OS funzionava tutto a dovere?.....
Sembrerebbe proprio una cattiva impostazone del BIOS....facci sapere----:confused:
ciao
si, funzionava tutto a dovere
ho installato ubunto dopo aver partizionato il disco su cui era gia' installato xp,
le periferiche usb non sono di tipo 2 (xp ogni volta che infilo una pen o un hd esterno xp mi avvisa) pero' ha funzionato tutto in modo regolare
il bios non mi consente di far modifiche di questo tipo: a dire il vero, a parte il cambio di ora e sequenza di boot, non consente quasi nulla :(
ho cercato in rete e ho visto che il problema (dell'acpi) e' capitato anche ad altri - seppur raramente - e che alcuni lo hanno risolto modificando il grub
ma io ho poca esperienza e non so proprio come cavarmela :confused:
capisco che il mio forse e' un caso particolare ma ... non vorrei pentirmi della scelta !!!
grazie per aver risposto :)
gianlucab70
05-09-2007, 21:38
....proprio mi dispiace ....non so come aiutarti---
speriamo nell'aiuto della comunità--a presto:confused:
ilsensine
05-09-2007, 21:57
lsusb:
Message from syslogd@amilo at ......
amilo kernel: [ 343.456000] Disabling IRQ #9
Solo una riga non dice il motivo, probabilmente un irq non gestito...
dmesg:
handlers:
[<c020c6a7>] (acpi_irq+0x0/0x14)
...dall'handler acpi. Questo messaggio è parte di un pezzo più lungo, che da altra informazioni. Visto che il computer non ti si è bloccato, è probabilmente scattato un WARN_ON.
Come effetto collaterale, un bel pò di hw potrebbe non funzionare. Forse non solo le porte usb.
In sintesi: hai un sospetto ACPI farlocco, fuori specifiche. E' comune tra i portatili.
Ti consiglio di provare con un live cd recente per vedere se la situazione migliora.
Solo una riga non dice il motivo, probabilmente un irq non gestito... ...dall'handler acpi. Questo messaggio è parte di un pezzo più lungo, che da altra informazioni. Visto che il computer non ti si è bloccato, è probabilmente scattato un WARN_ON.
Come effetto collaterale, un bel pò di hw potrebbe non funzionare. Forse non solo le porte usb.
cerco di salvare il messaggio completo poi lo posto
per l'hw non mi sembra: funziona tutto a dovere, solo le porte usb (sono 3 usb1) non vanno, qualsiasi sia la periferica collegata
Ti consiglio di provare con un live cd recente per vedere se la situazione migliora.
ora e' installato ubuntu 7.04, mi consigli un live cd con un'altra distribuzione?
a me viene un sospetto e - visto che sono inespeto - mi lancio senza vergogna: se fosse il kernel? provo a spiegarmi ...
il pc ha qualche anno, forse - anche se dovrebbe essere il contrario - con un kernel precedente potrebbe andare?
ricompilando il kernel e controllando che ci sia la gestione dell'acpi?
secondo voi c'e' modo di fare l'upgrade del bios?
grazie dell'aiuto :)
saluti
ilsensine
05-09-2007, 22:27
Sicuramente c'entra il kernel, lo aggiornano continuamente per gestire gli ACPI fuori standard, per questo ti ho consigliato un live cd recente (per curiosità, che kernel monta la tua ubuntu?)
Sicuramente c'entra il kernel, lo aggiornano continuamente per gestire gli ACPI fuori standard, per questo ti ho consigliato un live cd recente (per curiosità, che kernel monta la tua ubuntu?)
Ubuntu 7.04 con kernel 2.6.20
provando con uno precedente ci sono maggiori o minori possibilita?
visto che probabilmente non si potra' aggiornare il bios si puo' provare a cambiare distro?
ciao :)
ilsensine
05-09-2007, 22:58
Il 2.6.20 è abbastanza recente, non so se attualmente c'è un live cd con kernel successivo.
Puoi raccogliere l'intero dmesg e allegarlo?
Puoi raccogliere l'intero dmesg e allegarlo?
eccolo ...
utente@amilo:~$ lsusb
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
utente@amilo:~$
Message from syslogd@amilo at Thu Sep 6 09:16:28 2007 ...
amilo kernel: [ 1067.156000] Disabling IRQ #9
--------------------
utente@amilo:~$ dmesg
[ 0.000000] Linux version 2.6.20-15-generic (root@palmer) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Apr 15 07:36:31 UTC 2007 (Ubuntu 2.6.20-15.27-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 000000000009f800 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000d0000 size: 0000000000030000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000001bdf0000 end: 000000001bef0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000001bef0000 size: 000000000000f000 end: 000000001beff000 type: 3
[ 0.000000] copy_e820_map() start: 000000001beff000 size: 0000000000001000 end: 000000001bf00000 type: 4
[ 0.000000] copy_e820_map() start: 000000001bf00000 size: 0000000000100000 end: 000000001c000000 type: 2
[ 0.000000] copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001bef0000 (usable)
[ 0.000000] BIOS-e820: 000000001bef0000 - 000000001beff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001beff000 - 000000001bf00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001bf00000 - 000000001c000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 446MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 114416) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 114416
[ 0.000000] HighMem 114416 -> 114416
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 114416
[ 0.000000] On node 0 totalpages: 114416
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 861 pages used for memmap
[ 0.000000] Normal zone: 109459 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP (v000 PTLTD ) @ 0x000f7790
[ 0.000000] ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1befbc0a
[ 0.000000] ACPI: FADT (v001 ATI Raptor 0x06040000 ATI 0x000f4240) @ 0x1befee7b
[ 0.000000] ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x1befeeef
[ 0.000000] ACPI: DSDT (v001 COMPAL CY26____ 0x06040000 MSFT 0x0100000e) @ 0x00000000
[ 0.000000] ATI board detected. Disabling timer routing over 8254.
[ 0.000000] ACPI: PM-Timer IO Port: 0x8008
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 1c000000:e3f80000)
[ 0.000000] Detected 1788.870 MHz processor.
[ 13.963290] Built 1 zonelists. Total pages: 113523
[ 13.963295] Kernel command line: root=UUID=dd24c613-8075-4f1d-a65c-194d862fa3f0 ro quiet splash locale=it_IT
[ 13.963509] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 13.963526] mapped APIC to ffffd000 (0138a000)
[ 13.963533] Enabling fast FPU save and restore... done.
[ 13.963536] Enabling unmasked SIMD FPU exception support... done.
[ 13.963557] Initializing CPU#0
[ 13.963671] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 13.965269] Console: colour VGA+ 80x25
[ 13.966162] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 13.966643] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 13.989994] Memory: 442432k/457664k available (1992k kernel code, 14684k reserved, 893k data, 328k init, 0k highmem)
[ 13.990007] virtual kernel memory layout:
[ 13.990008] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 13.990010] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 13.990011] vmalloc : 0xdc800000 - 0xff7fe000 ( 559 MB)
[ 13.990013] lowmem : 0xc0000000 - 0xdbef0000 ( 446 MB)
[ 13.990014] .init : 0xc03d7000 - 0xc0429000 ( 328 kB)
[ 13.990015] .data : 0xc02f2264 - 0xc03d16d4 ( 893 kB)
[ 13.990017] .text : 0xc0100000 - 0xc02f2264 (1992 kB)
[ 13.990021] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 14.067603] Calibrating delay using timer specific routine.. 3579.82 BogoMIPS (lpj=7159649)
[ 14.067671] Security Framework v1.0.0 initialized
[ 14.067685] SELinux: Disabled at boot.
[ 14.067710] Mount-cache hash table entries: 512
[ 14.067966] CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000
[ 14.067978] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 14.067981] CPU: L2 Cache: 512K (64 bytes/line)
[ 14.067985] CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000420 00000000 00000000 00000000
[ 14.068001] Compat vDSO mapped to ffffe000.
[ 14.068010] Remapping vsyscall page to ffffe000
[ 14.068025] Checking 'hlt' instruction... OK.
[ 14.083819] SMP alternatives: switching to UP code
[ 14.084263] Freeing SMP alternatives: 11k freed
[ 14.084629] Early unpacking initramfs... done
[ 14.470859] ACPI: Core revision 20060707
[ 14.474620] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[ 14.476202] ACPI: setting ELCR to 0200 (from 0c20)
[ 14.574023] CPU0: AMD mobile AMD Athlon (tm) 2400+ stepping 00
[ 14.574032] SMP motherboard not detected.
[ 14.574037] Local APIC not detected. Using dummy APIC emulation.
[ 14.574126] Brought up 1 CPUs
[ 14.574582] Booting paravirtualized kernel on bare hardware
[ 14.574702] Time: 8:58:41 Date: 08/06/107
[ 14.574768] NET: Registered protocol family 16
[ 14.574951] EISA bus registered
[ 14.574958] ACPI: bus type pci registered
[ 14.597483] PCI: PCI BIOS revision 2.10 entry at 0xfd85e, last bus=1
[ 14.597487] PCI: Using configuration type 1
[ 14.597489] Setting up standard PCI resources
[ 14.603698] ACPI: Interpreter enabled
[ 14.603702] ACPI: Using PIC for interrupt routing
[ 14.604196] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 14.604204] PCI: Probing PCI hardware (bus 00)
[ 14.604258] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[ 14.604801] PCI quirk: region 8000-803f claimed by ali7101 ACPI
[ 14.604805] PCI quirk: region 8040-805f claimed by ali7101 SMB
[ 14.605118] Boot video device is 0000:01:05.0
[ 14.605253] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 14.607199] ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
[ 14.607437] ACPI: PCI Interrupt Link [LNKB] (IRQs *11)
[ 14.607673] ACPI: PCI Interrupt Link [LNKC] (IRQs 10) *5
[ 14.607902] ACPI: PCI Interrupt Link [LNKD] (IRQs 10) *0, disabled.
[ 14.608125] ACPI: PCI Interrupt Link [LNKE] (IRQs 5 9 *10 11)
[ 14.608350] ACPI: PCI Interrupt Link [LNKF] (IRQs 5 9 10 11) *0, disabled.
[ 14.608579] ACPI: PCI Interrupt Link [LNKG] (IRQs 5 9 10 *11)
[ 14.608803] ACPI: PCI Interrupt Link [LNKH] (IRQs 5 9 10 *11)
[ 14.609028] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.LPCB.LNKU._CRS] (Node da06ff7c), AE_TYPE
[ 14.609038] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 14.609044] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 14.609048] ACPI: PCI Interrupt Link [LNKU] (IRQs 9) *0
[ 16.606091] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[ 16.606614] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 16.606627] pnp: PnP ACPI init
[ 17.604895] pnp: PnP ACPI: found 12 devices
[ 17.604901] PnPBIOS: Disabled by ACPI PNP
[ 17.604989] PCI: Using ACPI for IRQ routing
[ 17.604993] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 17.606764] NET: Registered protocol family 8
[ 17.606767] NET: Registered protocol family 20
[ 17.607014] pnp: 00:07: ioport range 0x200-0x20f has been reserved
[ 17.607017] pnp: 00:07: ioport range 0x40b-0x40b has been reserved
[ 17.607020] pnp: 00:07: ioport range 0x480-0x48f has been reserved
[ 17.607023] pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 17.607367] PCI: Bridge: 0000:00:01.0
[ 17.607371] IO window: b000-bfff
[ 17.607376] MEM window: e8500000-e85fffff
[ 17.607380] PREFETCH window: f0000000-f7ffffff
[ 17.607385] PCI: Bus 2, cardbus bridge: 0000:00:0b.0
[ 17.607387] IO window: 00001000-000010ff
[ 17.607391] IO window: 00001400-000014ff
[ 17.607395] PREFETCH window: 20000000-23ffffff
[ 17.607399] MEM window: 24000000-27ffffff
[ 17.607403] PCI: Bus 6, cardbus bridge: 0000:00:0b.1
[ 17.607405] IO window: 00001800-000018ff
[ 17.607408] IO window: 00001c00-00001cff
[ 17.607412] PREFETCH window: 28000000-2bffffff
[ 17.607416] MEM window: 2c000000-2fffffff
[ 17.607627] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 17.607632] PCI: setting IRQ 11 as level-triggered
[ 17.607636] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 17.607811] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[ 17.607814] ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 17.607871] NET: Registered protocol family 2
[ 17.640971] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 17.641144] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 17.641609] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 17.641839] TCP: Hash tables configured (established 16384 bind 8192)
[ 17.641844] TCP reno registered
[ 17.652965] checking if image is initramfs... it is
[ 18.359849] Freeing initrd memory: 7004k freed
[ 18.360673] audit: initializing netlink socket (disabled)
[ 18.360702] audit(1189069125.492:1): initialized
[ 18.360883] VFS: Disk quotas dquot_6.5.1
[ 18.360913] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 18.360999] io scheduler noop registered
[ 18.361003] io scheduler anticipatory registered
[ 18.361006] io scheduler deadline registered
[ 18.361015] io scheduler cfq registered (default)
[ 18.361030] ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb.
[ 18.792032] Activating ISA DMA hang workarounds.
[ 18.792363] isapnp: Scanning for PnP cards...
[ 19.059163] isapnp: No Plug & Play device found
[ 19.091932] Real Time Clock Driver v1.12ac
[ 19.092020] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 19.092223] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 19.093140] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 19.093741] ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
[ 19.093748] ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11
[ 19.094931] 0000:00:03.0: ttyS1 at I/O 0x8428 (irq = 11) is a 8250
[ 19.095539] 0000:00:03.0: ttyS2 at I/O 0x8440 (irq = 11) is a 8250
[ 19.096019] 0000:00:03.0: ttyS3 at I/O 0x8450 (irq = 11) is a 8250
[ 19.096129] Couldn't register serial port 0000:00:03.0: -28
[ 19.096263] mice: PS/2 mouse device common for all mice
[ 19.097074] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 19.097486] input: Macintosh mouse button emulation as /class/input/input0
[ 19.097533] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 19.097539] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 19.097846] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 19.108519] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 19.115383] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 19.115390] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 19.115393] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 19.115396] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 19.115398] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 19.115827] EISA: Probing bus 0 at eisa.0
[ 19.115843] Cannot allocate resource for EISA slot 1
[ 19.115873] Cannot allocate resource for EISA slot 8
[ 19.115875] EISA: Detected 0 cards.
[ 19.146010] TCP cubic registered
[ 19.146020] NET: Registered protocol family 1
[ 19.146057] Using IPI No-Shortcut mode
[ 19.146151] ACPI: (supports S0 S3 S4 S5)
[ 19.146202] Magic number: 7:756:977
[ 19.146234] hash matches device ttyc4
[ 19.147367] Freeing unused kernel memory: 328k freed
[ 19.147793] Time: tsc clocksource has been installed.
[ 19.167999] input: AT Translated Set 2 keyboard as /class/input/input1
[ 20.410811] Capability LSM initialized
[ 20.455221] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 6.060000] Time: acpi_pm clocksource has been installed.
[ 8.012000] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707]
[ 10.012000] ACPI: Thermal Zone [THRM] (48 C)
[ 10.664000] usbcore: registered new interface driver usbfs
[ 10.664000] usbcore: registered new interface driver hub
[ 10.664000] usbcore: registered new device driver usb
[ 10.664000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.664000] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.LPCB.LNKU._CRS] (Node da06ff7c), AE_TYPE
[ 10.664000] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 10.664000] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 10.664000] ACPI: Unable to set IRQ for PCI Interrupt Link [LNKU]. Try pci=noacpi or acpi=off
[ 10.664000] ACPI: Invalid IRQ link routing entry
[ 10.664000] ACPI: Unable to derive IRQ for device 0000:00:02.0
[ 10.664000] ACPI: PCI Interrupt 0000:00:02.0[A]: no GSI - using IRQ 11
[ 10.664000] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 10.668000] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[ 10.668000] ohci_hcd 0000:00:02.0: irq 11, io mem 0xe8400000
[ 10.684000] SCSI subsystem initialized
[ 10.688000] libata version 2.20 loaded.
[ 10.732000] usb usb1: configuration #1 chosen from 1 choice
[ 10.732000] hub 1-0:1.0: USB hub found
[ 10.732000] hub 1-0:1.0: 2 ports detected
[ 10.740000] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 10.756000] ieee1394: Initialized config rom entry `ip1394'
[ 10.836000] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
[ 10.836000] PCI: setting IRQ 10 as level-triggered
[ 10.836000] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
[ 10.836000] ohci_hcd 0000:00:0f.0: OHCI Host Controller
[ 10.836000] ohci_hcd 0000:00:0f.0: new USB bus registered, assigned bus number 2
[ 10.836000] ohci_hcd 0000:00:0f.0: irq 10, io mem 0xe8405000
[ 10.892000] usb usb2: configuration #1 chosen from 1 choice
[ 10.892000] hub 2-0:1.0: USB hub found
[ 10.892000] hub 2-0:1.0: 2 ports detected
[ 10.936000] Floppy drive(s): fd0 is 1.44M
[ 10.972000] FDC 0 is a post-1991 82077
[ 10.996000] alim15x3: ATI Radeon IGP Northbridge is not yet fully tested.
[ 10.996000] ALI15X3: IDE controller at PCI slot 0000:00:04.0
[ 10.996000] ACPI: Unable to derive IRQ for device 0000:00:04.0
[ 10.996000] ACPI: PCI Interrupt 0000:00:04.0[A]: no GSI
[ 10.996000] ALI15X3: chipset revision 196
[ 10.996000] ALI15X3: not 100% native mode: will probe irqs later
[ 10.996000] ide0: BM-DMA at 0xa000-0xa007, BIOS settings: hda: DMA, hdb: pio
[ 10.996000] ide1: BM-DMA at 0xa008-0xa00f, BIOS settings: hdc: DMA, hdd: pio
[ 10.996000] Probing IDE interface ide0...
[ 11.288000] hda: FUJITSU MHS2040AT D, ATA DISK drive
[ 12.004000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 12.064000] Probing IDE interface ide1...
[ 12.800000] hdc: QSI CD-RW/DVD-ROM SBW-241, ATAPI CD/DVD-ROM drive
[ 13.136000] ide1 at 0x170-0x177,0x376 on irq 15
[ 13.136000] 8139cp 0000:00:09.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[ 13.136000] 8139cp 0000:00:09.0: Try the "8139too" driver instead.
[ 13.140000] 8139too Fast Ethernet driver 0.9.28
[ 13.140000] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 13.140000] eth0: RealTek RTL8139 at 0xdc846800, 00:02:3f:b5:aa:9a, IRQ 11
[ 13.140000] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 13.140000] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[ 13.140000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[ 13.196000] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[e8406000-e84067ff] Max Packet=[2048] IR/IT contexts=[8/8]
[ 13.212000] hda: max request size: 128KiB
[ 13.224000] hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
[ 13.228000] hda: cache flushes supported
[ 13.228000] hda: hda1 hda2 hda3 < hda5 >
[ 13.276000] hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 13.276000] Uniform CD-ROM driver Revision: 3.20
[ 13.676000] Attempting manual resume
[ 13.676000] swsusp: Resume From Partition 3:5
[ 13.676000] PM: Checking swsusp image.
[ 13.676000] PM: Resume from disk failed.
[ 13.716000] kjournald starting. Commit interval 5 seconds
[ 13.716000] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.476000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f322700129e]
[ 28.816000] eth0: link down
[ 30.384000] NET: Registered protocol family 17
[ 31.124000] ali15x3_smbus 0000:00:06.0: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
[ 31.124000] ali15x3_smbus 0000:00:06.0: ALI15X3 not detected, module not inserted.
[ 31.308000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 31.320000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 31.400000] Yenta: CardBus bridge found at 0000:00:0b.0 [1734:100a]
[ 31.400000] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 31.400000] Yenta: Routing CardBus interrupts to PCI
[ 31.400000] Yenta TI: socket 0000:00:0b.0, mfunc 0x011c1122, devctl 0x44
[ 31.632000] Yenta: ISA IRQ mask 0x00b8, PCI irq 11
[ 31.632000] Socket status: 30000006
[ 31.632000] Yenta: CardBus bridge found at 0000:00:0b.1 [1734:100a]
[ 31.632000] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 31.632000] Yenta: Routing CardBus interrupts to PCI
[ 31.632000] Yenta TI: socket 0000:00:0b.1, mfunc 0x011c1122, devctl 0x44
[ 31.672000] Linux agpgart interface v0.102 (c) Dave Jones
[ 31.748000] input: PC Speaker as /class/input/input2
[ 31.864000] Yenta: ISA IRQ mask 0x00b8, PCI irq 11
[ 31.864000] Socket status: 30000006
[ 31.864000] agpgart: Detected Ati IGP320/M chipset
[ 31.872000] agpgart: AGP aperture is 64M @ 0xec000000
[ 32.072000] parport: PnPBIOS parport detected.
[ 32.072000] parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 32.480000] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
[ 32.480000] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
[ 32.604000] input: ImPS/2 Logitech Wheel Mouse as /class/input/input3
[ 32.832000] cs: IO port probe 0x100-0x3af: excluding 0x220-0x22f 0x330-0x337 0x388-0x38f
[ 32.836000] cs: IO port probe 0x3e0-0x4ff: clean.
[ 32.836000] cs: IO port probe 0x820-0x8ff: clean.
[ 32.836000] cs: IO port probe 0xc00-0xcf7: clean.
[ 32.840000] cs: IO port probe 0xa00-0xaff: clean.
[ 32.840000] cs: IO port probe 0x100-0x3af: excluding 0x220-0x22f 0x330-0x337 0x388-0x38f
[ 32.844000] cs: IO port probe 0x3e0-0x4ff: clean.
[ 32.844000] cs: IO port probe 0x820-0x8ff: clean.
[ 32.844000] cs: IO port probe 0xc00-0xcf7: clean.
[ 32.848000] cs: IO port probe 0xa00-0xaff: clean.
[ 32.944000] input: PS/2 Mouse as /class/input/input4
[ 32.968000] input: AlpsPS/2 ALPS GlidePoint as /class/input/input5
[ 35.540000] AC'97 1 does not respond - RESET
[ 35.552000] AC'97 1 access is not valid [0xffffffff], removing mixer.
[ 35.552000] ali mixer 1 creating error.
[ 35.772000] fuse init (API version 7.8)
[ 35.804000] lp0: using parport0 (interrupt-driven).
[ 35.876000] Adding 819272k swap on /dev/disk/by-uuid/5280f007-9008-44cc-b3a9-87dba4738eca. Priority:-1 extents:1 across:819272k
[ 36.052000] EXT3 FS on hda2, internal journal
[ 45.972000] ACPI: Battery Slot [BAT1] (battery present)
[ 47.148000] ACPI: AC Adapter [ACAD] (on-line)
[ 47.160000] ibm_acpi: ec object not found
[ 47.196000] Using specific hotkey driver
[ 48.244000] No dock devices found.
[ 48.340000] input: Power Button (FF) as /class/input/input6
[ 48.348000] ACPI: Power Button (FF) [PWRF]
[ 48.384000] input: Lid Switch as /class/input/input7
[ 48.392000] ACPI: Lid Switch [LID]
[ 48.428000] input: Power Button (CM) as /class/input/input8
[ 48.436000] ACPI: Power Button (CM) [PWRB]
[ 48.508000] pcc_acpi: loading...
[ 48.896000] powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
[ 48.900000] powernow: SGTC: 13333
[ 48.900000] powernow: Minimum speed 662 MHz. Maximum speed 1788 MHz.
[ 69.884000] ppdev: user-space parallel port driver
[ 70.340000] mtrr: no more MTRRs available
[ 70.344000] mtrr: no more MTRRs available
[ 70.344000] mtrr: no more MTRRs available
[ 70.344000] mtrr: no more MTRRs available
[ 70.344000] mtrr: no more MTRRs available
[ 71.320000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 71.320000] apm: overridden by ACPI.
[ 71.556000] Bluetooth: Core ver 2.11
[ 71.556000] NET: Registered protocol family 31
[ 71.556000] Bluetooth: HCI device and connection manager initialized
[ 71.556000] Bluetooth: HCI socket layer initialized
[ 71.616000] Bluetooth: L2CAP ver 2.8
[ 71.616000] Bluetooth: L2CAP socket layer initialized
[ 71.772000] Bluetooth: RFCOMM socket layer initialized
[ 71.772000] Bluetooth: RFCOMM TTY layer initialized
[ 71.772000] Bluetooth: RFCOMM ver 1.8
[ 76.092000] NET: Registered protocol family 10
[ 76.092000] lo: Disabled Privacy Extensions
[ 76.092000] ADDRCONF(NETDEV_UP): eth0: link is not ready
utente@amilo:~$
Message from syslogd@amilo at Thu Sep 6 09:16:28 2007 ...
amilo kernel: [ 1067.156000] Disabling IRQ #9
utente@amilo:~$
ciao
Intanto potresti provare a seguire il suggerimento che il kernel stesso ti da:
[ 17.604993] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Per la cronaca quel comando lo devi inserire nella riga di avvio del kernel, quella con lo uuid della partizione, il tutto sta nel file /boot/grub/menu.lst
Per la cronaca quel comando lo devi inserire nella riga di avvio del kernel, quella con lo uuid della partizione, il tutto sta nel file /boot/grub/menu.lst
ho provato ma non va
ciao
cercando in rete ho trovato qualcosa riguardo a questo modello (amilo a2400) e a una installazione debia ma - purtroppo - in tedesco :(
ci sara' rimedio con un nuovo kernel?
conviene passare a una distribuzione diversa (debian per esempio) ?
ciao
cercando in rete ho trovato qualcosa riguardo a questo modello (amilo a2400) e a una installazione debia ma - purtroppo - in tedesco :(
ci sara' rimedio con un nuovo kernel?
conviene passare a una distribuzione diversa (debian per esempio) ?
ciao
Se la distriubuzione diversa ha un Kernel più nuovo un tentativo si può fare, certo più che reinstallare io proverei piuttosto a compilare un kernel vanilla, tanto non è difficile se alla fine vuoi solo mantenere le funzionalità base senza sbizzarrirti a personalizzarlo.
Ovvio questo comporterà qualche driver da installare nel caso usi driver proprietari per la scheda video, o per qualche periferica servano driver non presenti nel kernel vanilla ma aggiunti a quello Ubuntu dal team Canonical; quest'ultimo problema comunque si potrebbe porre anche cambiando distribuzione, visto che debian ad esempio usa solo kernel vanilla se non erro.
Ho qualche conoscenza di tedesco, se mi linki la guida di cui parli provo a vedere se capisco abbastanza da dirti la soluzione che hanno trovato li, ammesso che ci sia :)
non so se c'e' qualcosa di interessante: non capisco una parola di tedesco e forse ho preso una cantonata ... comunque ecco il link (http://www.qsl.net/df6fr/linux.htm)
ti segnalo anche questo (http://acpi.sourceforge.net/)... in inglese
ti ringrazio per la disponibilita' :)
ciao
In quello in tedesco non ho visto nulla di utile, però mi è venuta un'idea, ora ti linko io una guida da seguire.
http://guide.debianizzati.org/index.php/ACPI_e_DSDT
La cosa importante è che ti scarichi la dsdt e ne correggi gli errori, solo due correzioni alla guida.
1) Quando copi il file dsdt.aml in /etc/initramfs-tools devi rinominarlo in DSDT.aml
2) Una volta copiato il file è sufficiente dare sudo update-initramfs -u per aggiornarlo.
In bocca al lupo ^^
Se poi non ci riesci allega qui la Dsdt che ci do un'occhiata io, che ormai ne avrò sistemate una 10ina buona :D
sto leggendo la guida
se ho capito quello che hai suggerito, penso che ti stai riferendo al secondo metodo e cioe' a quello che non prevede la ricompilazione del kernel, giusto?
... il secondo inserisce la nuova DSDT all'interno dell'initrd, e quindi non necessita la ricompilazione del kernel ...
e la patch prevista dovrebbe essere gia' inclusa nel kernel di ubuntu
non mi e' tutto chiaro ma cerchero' di leggere con attenzione con la speranza di non far danni ...
ho visto che c'e' la possibilita' di scaricare una "custom dsdt" (ma il link pero' non e' corretto, andro' a spulciare nella pagina di download)
intanto ... continuo a leggere, non so se sono all'altezza (pero' sono testardo), mi faro' vivo
grazie ancora :)
sto leggendo la guida
se ho capito quello che hai suggerito, penso che ti stai riferendo al secondo metodo e cioe' a quello che non prevede la ricompilazione del kernel, giusto?
e la patch prevista dovrebbe essere gia' inclusa nel kernel di ubuntu
non mi e' tutto chiaro ma cerchero' di leggere con attenzione con la speranza di non far danni ...
ho visto che c'e' la possibilita' di scaricare una "custom dsdt" (ma il link pero' non e' corretto, andro' a spulciare nella pagina di download)
intanto ... continuo a leggere, non so se sono all'altezza (pero' sono testardo), mi faro' vivo
grazie ancora :)
Si, il metodo corretto nel tuo caso è il secondo, comunque non è nulla di così complicato, quando trovi gli errori basta usare Google e......il cervello :)
Per la possibilità di scaricarne una già sistemata si c'è, ma solo se qualcuno l'ha corretta e messa online prima di te per il tuo modello.
Ah, domandina un po' scontata: il bios è aggiornato all'ultima versione vero?
... Per la possibilità di scaricarne una già sistemata si c'è ...
il link nella guida non e' corretto, dovro' cercare meglio ...
... domandina un po' scontata: il bios è aggiornato all'ultima versione vero?
il bios su questo modello e' - come dire - "segato" nel senso che a parte la sequenza di boot e il cambio ora/data non fa fare praticamente nulla
ho guardato solo sul sito della fujitsu e per questo modello non ho trovato nulla, provero' a cercare su quello del costruttore della scheda madre con le dita incrociate ...
riciao
la ricerca dell'aggiornamento del bios ha dato il seguente risultato:
la eSupport, che cura gli aggiornamenti per conto della PhoenixBios, chiede 29,90 dollari .... pero' !!! :(
la ricerca dell'aggiornamento del bios ha dato il seguente risultato:
la eSupport, che cura gli aggiornamenti per conto della PhoenixBios, chiede 29,90 dollari .... pero' !!! :(
Naaa, quella è un'altra roba, se non hai trovato nulla ne sul sito del produttore allora nisba, l'upgrade di cui hai letto non è un aggiornamento del Bios come si intende nel modo classico ;)
Allora, questo è il link all'ultima versione del bios per il tuo portatile
Pagina di Download (http://support.fujitsu-siemens.com/Download/ShowDescription.asp?SoftwareGUID=BD46E2BF-781E-4517-A21B-9E85F20ED4CF&OSID=0708FF21-43FB-4FF7-9EE0-FCDDC4C258F5&Status=True&Component=Flash%20Bios%20for%20AMILO%20A7600)
E qui c'è il link alla dsdt relativa a questa versione del bios, e parla proprio della correzione al problema delle usb
DSDT Corretta (http://acpi.sourceforge.net/dsdt/view.php?id=346)
Fai così: scarichi il bios, tio servirà un floppy per aggiornarlo, e lo aggiorni, poi booti in un ubuntu, scarichi la dsdt dal secondo link, la copi in /etc/initramfs-tools stando attento a nominarla DSDT.dat (la maiuscola è importante), poi dail il comando sudo update-initramfs -u
Riavvia e incrocia le dita :)
ilsensine
09-09-2007, 09:59
eccolo ...
mmm in quel dmesg non c'è traccia del backtrace che mi attendevo, sicuro di averlo catturato "al momento giusto"?
Nel frattempo, prova con questi parametri di avvio:
acpi=noirq pci=noacpi
e vediamo se cambia qualcosa...
gli altri consigli che ti hanno dato possono o meno aiutare, puoi fare un tentativo.
Nel frattempo, prova con questi parametri di avvio:
acpi=noirq pci=noacpi
e vediamo se cambia qualcosa...
non va, stesso errore IRQ#9
Naaa, quella è un'altra roba, se non hai trovato nulla ne sul sito del produttore allora nisba, l'upgrade di cui hai letto non è un aggiornamento del Bios come si intende nel modo classico ;)
Allora, questo è il link all'ultima versione del bios per il tuo portatile
non credo vada bene, il modello e' differente: il mio e' il a2400
E qui c'è il link alla dsdt relativa a questa versione del bios, e parla proprio della correzione al problema delle usb
stesso discorso, non credo vada bene, magari posso studiarlo come esempio
allora ...
ho installato il compilatore e ho fatto quello che indica la guida,
il risultato della ricompilazione mi restituisce questo:
--
Intel ACPI Component Architecture
ASL Optimizing Compiler version 20060912 [Dec 6 2006]
Copyright (C) 2000 - 2006 Intel Corporation
Supports ACPI Specification Revision 3.0a
ASL Input: dsdt.dsl - 3143 lines, 116062 bytes, 1325 keywords
Compilation complete. 3 Errors, 1 Warnings, 0 Remarks, 446 Optimizations
------------------------
dsdt.dsl 92: Method (_WAK, 1, NotSerialized)
Warning 1079 - ^ Reserved method must return a value (_WAK)
-
Method (_WAK, 1, NotSerialized)
{
If (LEqual (Arg0, 0x04))
{
If (\_SB.PCI0.LPCB.EC0.ECOK)
{
Store (0x00, SLPT)
\_SB.PCI0.LPCB.PHSS (0x98)
}
}
}
------------------------
dsdt.dsl 775: Return (Local0)
Error 4049 - ^ Method local variable is not initialized (Local0)
-
Method (_CRS, 0, NotSerialized)
{
Name (RTLU, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, _Y0A)
{}
})
CreateWordField (RTLU, \_SB.PCI0.LPCB.LNKU._CRS._Y0A._INT, IRQ8)
Store (PIRU, Local1)
Store (DerefOf (Index (IXLT, Local1)), IRQ8)
Return (Local0)
}
-
------------------------
dsdt.dsl 1909: Field (ERAM, AnyAcc, Lock, Preserve)
Error 4074 - ^ Host Operation Region requires ByteAcc access
-
Device (MEM)
{
Name (_HID, EisaId ("PNP0C01"))
Name (MSRC, ResourceTemplate ()
{
Memory32Fixed (ReadWrite,
0x00000000, // Address Base
0x00000000, // Address Length
_Y0B)
Memory32Fixed (ReadWrite,
0x00000000, // Address Base
0x000A0000, // Address Length
)
Memory32Fixed (ReadOnly,
0x000C0000, // Address Base
0x0000F000, // Address Length
)
Memory32Fixed (ReadOnly,
0x000DC000, // Address Base
0x00004000, // Address Length
)
Memory32Fixed (ReadOnly,
0x000EC000, // Address Base
0x00014000, // Address Length
)
Memory32Fixed (ReadWrite,
0x00100000, // Address Base
0x07F00000, // Address Length
_Y0C)
Memory32Fixed (ReadOnly,
0xFFF80000, // Address Base
0x00080000, // Address Length
)
})
-
------------------------
dsdt.dsl 2024: Field (ECRM, AnyAcc, Lock, Preserve)
Error 4074 - ^ Host Operation Region requires ByteAcc access
-
OperationRegion (ECRM, EmbeddedControl, 0x00, 0xFF)
Field (ECRM, AnyAcc, Lock, Preserve)
{
Offset (0xAE),
THR0, 7,
THR7, 1
}
----------------------------
(ho fatto un copia/incolla dei file ...
ma ora non so come modificare ...
ciao ciao
ilsensine
10-09-2007, 16:41
non va, stesso errore IRQ#9
e un sonoro
acpi=off
cambia qualcosa? Se non cambia nulla, allega il dmesg (completo dei messaggi di errore sull'irq 9 possibilmente)
e un sonoro
acpi=off
cambia qualcosa? Se non cambia nulla, allega il dmesg (completo dei messaggi di errore sull'irq 9 possibilmente)
ecco il dmesg con acpi=off
vidocq@amilo:~$ sudo gedit
Password:
vidocq@amilo:~$ dmesg
[ 0.000000] Linux version 2.6.20-16-generic (root@terranova) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Fri Aug 31 00:55:27 UTC 2007 (Ubuntu 2.6.20-16.31-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 000000000009f800 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000d0000 size: 0000000000030000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000001bdf0000 end: 000000001bef0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000001bef0000 size: 000000000000f000 end: 000000001beff000 type: 3
[ 0.000000] copy_e820_map() start: 000000001beff000 size: 0000000000001000 end: 000000001bf00000 type: 4
[ 0.000000] copy_e820_map() start: 000000001bf00000 size: 0000000000100000 end: 000000001c000000 type: 2
[ 0.000000] copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001bef0000 (usable)
[ 0.000000] BIOS-e820: 000000001bef0000 - 000000001beff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001beff000 - 000000001bf00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001bf00000 - 000000001c000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 446MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 114416) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 114416
[ 0.000000] HighMem 114416 -> 114416
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 114416
[ 0.000000] On node 0 totalpages: 114416
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 861 pages used for memmap
[ 0.000000] Normal zone: 109459 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP (v000 PTLTD ) @ 0x000f7790
[ 0.000000] ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1befbc0a
[ 0.000000] ACPI: FADT (v001 ATI Raptor 0x06040000 ATI 0x000f4240) @ 0x1befee7b
[ 0.000000] ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x1befeeef
[ 0.000000] ACPI: DSDT (v001 COMPAL CY26____ 0x06040000 MSFT 0x0100000e) @ 0x00000000
[ 0.000000] ATI board detected. Disabling timer routing over 8254.
[ 0.000000] ACPI: PM-Timer IO Port: 0x8008
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 1c000000:e3f80000)
[ 0.000000] Detected 1788.970 MHz processor.
[ 11.991195] Built 1 zonelists. Total pages: 113523
[ 11.991202] Kernel command line: root=UUID=dd24c613-8075-4f1d-a65c-194d862fa3f0 ro quiet splash locale=it_IT
[ 11.991413] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 11.991431] mapped APIC to ffffd000 (0138a000)
[ 11.991437] Enabling fast FPU save and restore... done.
[ 11.991440] Enabling unmasked SIMD FPU exception support... done.
[ 11.991461] Initializing CPU#0
[ 11.991575] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 11.993218] Console: colour VGA+ 80x25
[ 11.994110] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 11.994590] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 12.017860] Memory: 442680k/457664k available (1993k kernel code, 14468k reserved, 900k data, 328k init, 0k highmem)
[ 12.017874] virtual kernel memory layout:
[ 12.017875] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 12.017877] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 12.017878] vmalloc : 0xdc800000 - 0xff7fe000 ( 559 MB)
[ 12.017879] lowmem : 0xc0000000 - 0xdbef0000 ( 446 MB)
[ 12.017881] .init : 0xc03d9000 - 0xc042b000 ( 328 kB)
[ 12.017882] .data : 0xc02f2434 - 0xc03d36d4 ( 900 kB)
[ 12.017884] .text : 0xc0100000 - 0xc02f2434 (1993 kB)
[ 12.017887] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 12.095508] Calibrating delay using timer specific routine.. 3579.91 BogoMIPS (lpj=7159831)
[ 12.095579] Security Framework v1.0.0 initialized
[ 12.095592] SELinux: Disabled at boot.
[ 12.095617] Mount-cache hash table entries: 512
[ 12.095877] CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000
[ 12.095890] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 12.095893] CPU: L2 Cache: 512K (64 bytes/line)
[ 12.095897] CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000420 00000000 00000000 00000000
[ 12.095912] Compat vDSO mapped to ffffe000.
[ 12.095922] Remapping vsyscall page to ffffe000
[ 12.095937] Checking 'hlt' instruction... OK.
[ 12.111725] SMP alternatives: switching to UP code
[ 12.112176] Freeing SMP alternatives: 11k freed
[ 12.112539] Early unpacking initramfs... done
[ 12.485765] ACPI: Core revision 20060707
[ 12.489510] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[ 12.491102] ACPI: setting ELCR to 0200 (from 0c20)
[ 12.588934] CPU0: AMD mobile AMD Athlon (tm) 2400+ stepping 00
[ 12.588944] SMP motherboard not detected.
[ 12.588948] Local APIC not detected. Using dummy APIC emulation.
[ 12.589036] Brought up 1 CPUs
[ 12.589479] Booting paravirtualized kernel on bare hardware
[ 12.589610] Time: 18:04:19 Date: 08/10/107
[ 12.589674] NET: Registered protocol family 16
[ 12.589855] EISA bus registered
[ 12.589862] ACPI: bus type pci registered
[ 12.612405] PCI: PCI BIOS revision 2.10 entry at 0xfd85e, last bus=1
[ 12.612408] PCI: Using configuration type 1
[ 12.612411] Setting up standard PCI resources
[ 12.618613] ACPI: Interpreter enabled
[ 12.618617] ACPI: Using PIC for interrupt routing
[ 12.619112] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 12.619120] PCI: Probing PCI hardware (bus 00)
[ 12.619181] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[ 12.619700] PCI quirk: region 8000-803f claimed by ali7101 ACPI
[ 12.619704] PCI quirk: region 8040-805f claimed by ali7101 SMB
[ 12.620019] Boot video device is 0000:01:05.0
[ 12.620153] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 12.622127] ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
[ 12.622356] ACPI: PCI Interrupt Link [LNKB] (IRQs *11)
[ 12.622582] ACPI: PCI Interrupt Link [LNKC] (IRQs 10) *5
[ 12.622807] ACPI: PCI Interrupt Link [LNKD] (IRQs 10) *0, disabled.
[ 12.623030] ACPI: PCI Interrupt Link [LNKE] (IRQs 5 9 *10 11)
[ 12.623265] ACPI: PCI Interrupt Link [LNKF] (IRQs 5 9 10 11) *0, disabled.
[ 12.623492] ACPI: PCI Interrupt Link [LNKG] (IRQs 5 9 10 *11)
[ 12.623716] ACPI: PCI Interrupt Link [LNKH] (IRQs 5 9 10 *11)
[ 12.623944] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.LPCB.LNKU._CRS] (Node da785f7c), AE_TYPE
[ 12.623954] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 12.623961] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 12.623965] ACPI: PCI Interrupt Link [LNKU] (IRQs 9) *0
[ 14.621984] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[ 14.622508] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 14.622536] pnp: PnP ACPI init
[ 15.620795] pnp: PnP ACPI: found 12 devices
[ 15.620801] PnPBIOS: Disabled by ACPI PNP
[ 15.620889] PCI: Using ACPI for IRQ routing
[ 15.620894] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 15.622671] NET: Registered protocol family 8
[ 15.622674] NET: Registered protocol family 20
[ 15.622908] pnp: 00:07: ioport range 0x200-0x20f has been reserved
[ 15.622911] pnp: 00:07: ioport range 0x40b-0x40b has been reserved
[ 15.622915] pnp: 00:07: ioport range 0x480-0x48f has been reserved
[ 15.622918] pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 15.623280] PCI: Bridge: 0000:00:01.0
[ 15.623284] IO window: b000-bfff
[ 15.623289] MEM window: e8500000-e85fffff
[ 15.623293] PREFETCH window: f0000000-f7ffffff
[ 15.623298] PCI: Bus 2, cardbus bridge: 0000:00:0b.0
[ 15.623301] IO window: 00001000-000010ff
[ 15.623305] IO window: 00001400-000014ff
[ 15.623309] PREFETCH window: 20000000-23ffffff
[ 15.623313] MEM window: 24000000-27ffffff
[ 15.623316] PCI: Bus 6, cardbus bridge: 0000:00:0b.1
[ 15.623318] IO window: 00001800-000018ff
[ 15.623322] IO window: 00001c00-00001cff
[ 15.623326] PREFETCH window: 28000000-2bffffff
[ 15.623330] MEM window: 2c000000-2fffffff
[ 15.623537] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 15.623542] PCI: setting IRQ 11 as level-triggered
[ 15.623546] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 15.623721] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[ 15.623724] ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 15.623784] NET: Registered protocol family 2
[ 15.656874] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 15.657054] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 15.657531] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 15.657765] TCP: Hash tables configured (established 16384 bind 8192)
[ 15.657769] TCP reno registered
[ 15.668861] checking if image is initramfs... it is
[ 16.354474] Freeing initrd memory: 6782k freed
[ 16.355273] audit: initializing netlink socket (disabled)
[ 16.355304] audit(1189447462.460:1): initialized
[ 16.355487] VFS: Disk quotas dquot_6.5.1
[ 16.355515] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 16.355603] io scheduler noop registered
[ 16.355607] io scheduler anticipatory registered
[ 16.355610] io scheduler deadline registered
[ 16.355620] io scheduler cfq registered (default)
[ 16.355636] ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb.
[ 16.787943] Activating ISA DMA hang workarounds.
[ 16.788262] isapnp: Scanning for PnP cards...
[ 17.055060] isapnp: No Plug & Play device found
[ 17.087111] Real Time Clock Driver v1.12ac
[ 17.087202] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 17.087391] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 17.088279] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 17.088866] ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
[ 17.088872] ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11
[ 17.089975] 0000:00:03.0: ttyS1 at I/O 0x8428 (irq = 11) is a 8250
[ 17.090507] 0000:00:03.0: ttyS2 at I/O 0x8440 (irq = 11) is a 8250
[ 17.090872] 0000:00:03.0: ttyS3 at I/O 0x8450 (irq = 11) is a 8250
[ 17.090961] Couldn't register serial port 0000:00:03.0: -28
[ 17.091077] mice: PS/2 mouse device common for all mice
[ 17.092003] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 17.092422] input: Macintosh mouse button emulation as /class/input/input0
[ 17.092467] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 17.092473] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 17.092795] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 17.103362] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 17.108494] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 17.108500] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 17.108503] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 17.108506] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 17.108509] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 17.109222] EISA: Probing bus 0 at eisa.0
[ 17.109237] Cannot allocate resource for EISA slot 1
[ 17.109267] Cannot allocate resource for EISA slot 8
[ 17.109269] EISA: Detected 0 cards.
[ 17.139399] TCP cubic registered
[ 17.139409] NET: Registered protocol family 1
[ 17.139441] Using IPI No-Shortcut mode
[ 17.139540] ACPI: (supports S0 S3 S4 S5)
[ 17.139593] Magic number: 7:192:89
[ 17.139699] Time: tsc clocksource has been installed.
[ 17.140805] Freeing unused kernel memory: 328k freed
[ 17.155847] input: AT Translated Set 2 keyboard as /class/input/input1
[ 18.402641] Capability LSM initialized
[ 18.446437] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 6.024000] Time: acpi_pm clocksource has been installed.
[ 7.976000] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707]
[ 9.976000] ACPI: Thermal Zone [THRM] (67 C)
[ 10.644000] usbcore: registered new interface driver usbfs
[ 10.644000] usbcore: registered new interface driver hub
[ 10.644000] usbcore: registered new device driver usb
[ 10.644000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.656000] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.LPCB.LNKU._CRS] (Node da785f7c), AE_TYPE
[ 10.656000] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 10.656000] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 10.656000] ACPI: Unable to set IRQ for PCI Interrupt Link [LNKU]. Try pci=noacpi or acpi=off
[ 10.656000] ACPI: Invalid IRQ link routing entry
[ 10.656000] ACPI: Unable to derive IRQ for device 0000:00:02.0
[ 10.656000] ACPI: PCI Interrupt 0000:00:02.0[A]: no GSI - using IRQ 11
[ 10.656000] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 10.660000] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[ 10.660000] ohci_hcd 0000:00:02.0: irq 11, io mem 0xe8400000
[ 10.676000] SCSI subsystem initialized
[ 10.680000] libata version 2.20 loaded.
[ 10.724000] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 10.736000] usb usb1: configuration #1 chosen from 1 choice
[ 10.736000] hub 1-0:1.0: USB hub found
[ 10.736000] hub 1-0:1.0: 2 ports detected
[ 10.752000] ieee1394: Initialized config rom entry `ip1394'
[ 10.840000] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
[ 10.840000] PCI: setting IRQ 10 as level-triggered
[ 10.840000] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
[ 10.840000] ohci_hcd 0000:00:0f.0: OHCI Host Controller
[ 10.840000] ohci_hcd 0000:00:0f.0: new USB bus registered, assigned bus number 2
[ 10.840000] ohci_hcd 0000:00:0f.0: irq 10, io mem 0xe8405000
[ 10.896000] usb usb2: configuration #1 chosen from 1 choice
[ 10.896000] hub 2-0:1.0: USB hub found
[ 10.896000] hub 2-0:1.0: 2 ports detected
[ 10.956000] Floppy drive(s): fd0 is 1.44M
[ 10.980000] FDC 0 is a post-1991 82077
[ 11.000000] alim15x3: ATI Radeon IGP Northbridge is not yet fully tested.
[ 11.000000] ALI15X3: IDE controller at PCI slot 0000:00:04.0
[ 11.000000] ACPI: Unable to derive IRQ for device 0000:00:04.0
[ 11.000000] ACPI: PCI Interrupt 0000:00:04.0[A]: no GSI
[ 11.000000] ALI15X3: chipset revision 196
[ 11.000000] ALI15X3: not 100% native mode: will probe irqs later
[ 11.000000] ide0: BM-DMA at 0xa000-0xa007, BIOS settings: hda:DMA, hdb:pio
[ 11.000000] ide1: BM-DMA at 0xa008-0xa00f, BIOS settings: hdc:DMA, hdd:pio
[ 11.000000] Probing IDE interface ide0...
[ 11.292000] hda: FUJITSU MHS2040AT D, ATA DISK drive
[ 12.008000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 12.068000] Probing IDE interface ide1...
[ 12.804000] hdc: QSI CD-RW/DVD-ROM SBW-241, ATAPI CD/DVD-ROM drive
[ 13.140000] ide1 at 0x170-0x177,0x376 on irq 15
[ 13.140000] 8139cp 0000:00:09.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[ 13.140000] 8139cp 0000:00:09.0: Try the "8139too" driver instead.
[ 13.144000] 8139too Fast Ethernet driver 0.9.28
[ 13.144000] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 13.144000] eth0: RealTek RTL8139 at 0xdc846800, 00:02:3f:b5:aa:9a, IRQ 11
[ 13.144000] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 13.144000] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[ 13.144000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[ 13.196000] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[e8406000-e84067ff] Max Packet=[2048] IR/IT contexts=[8/8]
[ 13.212000] hda: max request size: 128KiB
[ 13.232000] hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
[ 13.232000] hda: cache flushes supported
[ 13.232000] hda: hda1 hda2 hda3 < hda5 >
[ 13.280000] hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 13.280000] Uniform CD-ROM driver Revision: 3.20
[ 13.668000] Attempting manual resume
[ 13.668000] swsusp: Resume From Partition 3:5
[ 13.668000] PM: Checking swsusp image.
[ 13.668000] PM: Resume from disk failed.
[ 13.716000] kjournald starting. Commit interval 5 seconds
[ 13.716000] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.500000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f322700129e]
[ 30.092000] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 31.656000] NET: Registered protocol family 17
[ 32.284000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 32.332000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 32.448000] ali15x3_smbus 0000:00:06.0: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
[ 32.452000] ali15x3_smbus 0000:00:06.0: ALI15X3 not detected, module not inserted.
[ 32.604000] Yenta: CardBus bridge found at 0000:00:0b.0 [1734:100a]
[ 32.604000] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 32.604000] Yenta: Routing CardBus interrupts to PCI
[ 32.604000] Yenta TI: socket 0000:00:0b.0, mfunc 0x011c1122, devctl 0x44
[ 32.836000] Yenta: ISA IRQ mask 0x00b8, PCI irq 11
[ 32.836000] Socket status: 30000006
[ 32.836000] Yenta: CardBus bridge found at 0000:00:0b.1 [1734:100a]
[ 32.836000] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 32.836000] Yenta: Routing CardBus interrupts to PCI
[ 32.836000] Yenta TI: socket 0000:00:0b.1, mfunc 0x011c1122, devctl 0x44
[ 33.068000] Yenta: ISA IRQ mask 0x00b8, PCI irq 11
[ 33.068000] Socket status: 30000006
[ 33.184000] Linux agpgart interface v0.102 (c) Dave Jones
[ 33.192000] agpgart: Detected Ati IGP320/M chipset
[ 33.200000] agpgart: AGP aperture is 64M @ 0xec000000
[ 33.388000] input: PC Speaker as /class/input/input2
[ 33.488000] parport: PnPBIOS parport detected.
[ 33.488000] parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 33.824000] input: ImPS/2 Logitech Wheel Mouse as /class/input/input3
[ 33.960000] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
[ 33.960000] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
[ 34.176000] input: PS/2 Mouse as /class/input/input4
[ 34.204000] input: AlpsPS/2 ALPS GlidePoint as /class/input/input5
[ 34.232000] cs: IO port probe 0x100-0x3af: excluding 0x220-0x22f 0x330-0x337 0x388-0x38f
[ 34.328000] cs: IO port probe 0x100-0x3af: excluding 0x220-0x22f 0x330-0x337 0x388-0x38f
[ 34.332000] cs: IO port probe 0x3e0-0x4ff: clean.
[ 34.332000] cs: IO port probe 0x820-0x8ff: clean.
[ 34.332000] cs: IO port probe 0xc00-0xcf7: clean.
[ 34.332000] cs: IO port probe 0xa00-0xaff: clean.
[ 34.336000] cs: IO port probe 0x3e0-0x4ff: clean.
[ 34.336000] cs: IO port probe 0x820-0x8ff: clean.
[ 34.336000] cs: IO port probe 0xc00-0xcf7: clean.
[ 34.336000] cs: IO port probe 0xa00-0xaff: clean.
[ 37.052000] AC'97 1 does not respond - RESET
[ 37.068000] AC'97 1 access is not valid [0xffffffff], removing mixer.
[ 37.068000] ali mixer 1 creating error.
[ 37.316000] fuse init (API version 7.8)
[ 37.368000] lp0: using parport0 (interrupt-driven).
[ 37.432000] Adding 819272k swap on /dev/disk/by-uuid/5280f007-9008-44cc-b3a9-87dba4738eca. Priority:-1 extents:1 across:819272k
[ 37.608000] EXT3 FS on hda2, internal journal
[ 37.860000] NET: Registered protocol family 10
[ 37.860000] lo: Disabled Privacy Extensions
[ 47.540000] ACPI: Battery Slot [BAT1] (battery present)
[ 48.448000] eth0: no IPv6 routers present
[ 48.760000] ACPI: AC Adapter [ACAD] (off-line)
[ 48.784000] ibm_acpi: ec object not found
[ 48.812000] Using specific hotkey driver
[ 49.856000] No dock devices found.
[ 49.968000] input: Power Button (FF) as /class/input/input6
[ 49.976000] ACPI: Power Button (FF) [PWRF]
[ 50.012000] input: Lid Switch as /class/input/input7
[ 50.020000] ACPI: Lid Switch [LID]
[ 50.056000] input: Power Button (CM) as /class/input/input8
[ 50.064000] ACPI: Power Button (CM) [PWRB]
[ 50.132000] pcc_acpi: loading...
[ 50.500000] powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
[ 50.504000] powernow: SGTC: 13333
[ 50.504000] powernow: Minimum speed 662 MHz. Maximum speed 1788 MHz.
[ 71.416000] ppdev: user-space parallel port driver
[ 71.992000] mtrr: no more MTRRs available
[ 71.992000] mtrr: no more MTRRs available
[ 71.992000] mtrr: no more MTRRs available
[ 71.992000] mtrr: no more MTRRs available
[ 71.992000] mtrr: no more MTRRs available
[ 73.024000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 73.024000] apm: overridden by ACPI.
[ 73.304000] Bluetooth: Core ver 2.11
[ 73.304000] NET: Registered protocol family 31
[ 73.304000] Bluetooth: HCI device and connection manager initialized
[ 73.304000] Bluetooth: HCI socket layer initialized
[ 73.372000] Bluetooth: L2CAP ver 2.8
[ 73.372000] Bluetooth: L2CAP socket layer initialized
[ 73.516000] Bluetooth: RFCOMM socket layer initialized
[ 73.516000] Bluetooth: RFCOMM TTY layer initialized
[ 73.516000] Bluetooth: RFCOMM ver 1.8
vidocq@amilo:~$
Message from syslogd@amilo at Mon Sep 10 18:09:12 2007 ...
amilo kernel: [ 293.468000] Disabling IRQ #9
ciao :)
ilsensine
10-09-2007, 18:10
No, non ci siamo:
[ 11.991202] Kernel command line: root=UUID=dd24c613-8075-4f1d-a65c-194d862fa3f0 ro quiet splash locale=it_IT
non hai passato correttamente acpi=xxx.
ilsensine
10-09-2007, 18:11
Nota inoltre che _dopo_ che leggi questo:
Message from syslogd@amilo at Mon Sep 10 18:09:12 2007 ...
amilo kernel: [ 293.468000] Disabling IRQ #9
dovresti trovare qualcosa di interessante in dmesg. I tuoi messaggi invece non contengono questo errore, sono stati quindi catturati _prima_.
non hai passato correttamente acpi=xxx
ho inserito acpi=off nella riga di start del kernel
sono stati quindi catturati _prima_.
forse ho sbagliato: ho catturato il dmesg, poi ho inserito la pen e ho ri_catturato lo stesso dmesg con l'errore senza rieseguire da capo
lo rifaccio da capo poi lo posto di nuovo
porta pazienza :) , l'inesperienza mi fa muovere in modo sbagliato ...
ilsensine
10-09-2007, 19:32
ho inserito acpi=off nella riga di start del kernel
In che modo, esattamente? In genere si possono passare questi parametri all'avvio tramite il bootloader. E' la soluzione più semplice (e reversibile, se fai qualche errore che rende il sistema non avviabile).
ho aggiunto iquesti parametri acpi=noirq pci=noacpi nella riga di avvio del kernel all'interno del file /boot/grub/menu.lst
questo e' il dmesg prima dell'inserimento della pen
utente@amilo:~$ dmesg
[ 0.000000] Linux version 2.6.20-16-generic (root@terranova) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Fri Aug 31 00:55:27 UTC 2007 (Ubuntu 2.6.20-16.31-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 000000000009f800 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000d0000 size: 0000000000030000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000001bdf0000 end: 000000001bef0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000001bef0000 size: 000000000000f000 end: 000000001beff000 type: 3
[ 0.000000] copy_e820_map() start: 000000001beff000 size: 0000000000001000 end: 000000001bf00000 type: 4
[ 0.000000] copy_e820_map() start: 000000001bf00000 size: 0000000000100000 end: 000000001c000000 type: 2
[ 0.000000] copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001bef0000 (usable)
[ 0.000000] BIOS-e820: 000000001bef0000 - 000000001beff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001beff000 - 000000001bf00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001bf00000 - 000000001c000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 446MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 114416) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 114416
[ 0.000000] HighMem 114416 -> 114416
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 114416
[ 0.000000] On node 0 totalpages: 114416
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 861 pages used for memmap
[ 0.000000] Normal zone: 109459 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP (v000 PTLTD ) @ 0x000f7790
[ 0.000000] ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1befbc0a
[ 0.000000] ACPI: FADT (v001 ATI Raptor 0x06040000 ATI 0x000f4240) @ 0x1befee7b
[ 0.000000] ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x1befeeef
[ 0.000000] ACPI: DSDT (v001 COMPAL CY26____ 0x06040000 MSFT 0x0100000e) @ 0x00000000
[ 0.000000] ATI board detected. Disabling timer routing over 8254.
[ 0.000000] ACPI: PM-Timer IO Port: 0x8008
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 1c000000:e3f80000)
[ 0.000000] Detected 1788.898 MHz processor.
[ 17.438341] Built 1 zonelists. Total pages: 113523
[ 17.438348] Kernel command line: root=UUID=dd24c613-8075-4f1d-a65c-194d862fa3f0 ro quiet splash locale=it_IT
[ 17.438559] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 17.438577] mapped APIC to ffffd000 (0138a000)
[ 17.438583] Enabling fast FPU save and restore... done.
[ 17.438586] Enabling unmasked SIMD FPU exception support... done.
[ 17.438607] Initializing CPU#0
[ 17.438720] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 17.440356] Console: colour VGA+ 80x25
[ 17.441248] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 17.441728] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 17.465049] Memory: 442680k/457664k available (1993k kernel code, 14468k reserved, 900k data, 328k init, 0k highmem)
[ 17.465063] virtual kernel memory layout:
[ 17.465064] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 17.465066] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 17.465067] vmalloc : 0xdc800000 - 0xff7fe000 ( 559 MB)
[ 17.465069] lowmem : 0xc0000000 - 0xdbef0000 ( 446 MB)
[ 17.465070] .init : 0xc03d9000 - 0xc042b000 ( 328 kB)
[ 17.465072] .data : 0xc02f2434 - 0xc03d36d4 ( 900 kB)
[ 17.465073] .text : 0xc0100000 - 0xc02f2434 (1993 kB)
[ 17.465077] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 17.542652] Calibrating delay using timer specific routine.. 3579.78 BogoMIPS (lpj=7159574)
[ 17.542723] Security Framework v1.0.0 initialized
[ 17.542736] SELinux: Disabled at boot.
[ 17.542761] Mount-cache hash table entries: 512
[ 17.543017] CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000
[ 17.543030] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 17.543033] CPU: L2 Cache: 512K (64 bytes/line)
[ 17.543037] CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000420 00000000 00000000 00000000
[ 17.543052] Compat vDSO mapped to ffffe000.
[ 17.543061] Remapping vsyscall page to ffffe000
[ 17.543077] Checking 'hlt' instruction... OK.
[ 17.558869] SMP alternatives: switching to UP code
[ 17.559314] Freeing SMP alternatives: 11k freed
[ 17.559671] Early unpacking initramfs... done
[ 17.932724] ACPI: Core revision 20060707
[ 17.936481] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[ 17.938054] ACPI: setting ELCR to 0200 (from 0c20)
[ 18.035889] CPU0: AMD mobile AMD Athlon (tm) 2400+ stepping 00
[ 18.035899] SMP motherboard not detected.
[ 18.035903] Local APIC not detected. Using dummy APIC emulation.
[ 18.035992] Brought up 1 CPUs
[ 18.036442] Booting paravirtualized kernel on bare hardware
[ 18.036574] Time: 21:35:08 Date: 08/10/107
[ 18.036639] NET: Registered protocol family 16
[ 18.036822] EISA bus registered
[ 18.036829] ACPI: bus type pci registered
[ 18.059320] PCI: PCI BIOS revision 2.10 entry at 0xfd85e, last bus=1
[ 18.059323] PCI: Using configuration type 1
[ 18.059326] Setting up standard PCI resources
[ 18.065509] ACPI: Interpreter enabled
[ 18.065512] ACPI: Using PIC for interrupt routing
[ 18.066012] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 18.066020] PCI: Probing PCI hardware (bus 00)
[ 18.066070] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[ 18.066603] PCI quirk: region 8000-803f claimed by ali7101 ACPI
[ 18.066607] PCI quirk: region 8040-805f claimed by ali7101 SMB
[ 18.066923] Boot video device is 0000:01:05.0
[ 18.067058] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 18.069045] ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
[ 18.069273] ACPI: PCI Interrupt Link [LNKB] (IRQs *11)
[ 18.069498] ACPI: PCI Interrupt Link [LNKC] (IRQs 10) *5
[ 18.069722] ACPI: PCI Interrupt Link [LNKD] (IRQs 10) *0, disabled.
[ 18.069946] ACPI: PCI Interrupt Link [LNKE] (IRQs 5 9 *10 11)
[ 18.070171] ACPI: PCI Interrupt Link [LNKF] (IRQs 5 9 10 11) *0, disabled.
[ 18.070405] ACPI: PCI Interrupt Link [LNKG] (IRQs 5 9 10 *11)
[ 18.070629] ACPI: PCI Interrupt Link [LNKH] (IRQs 5 9 10 *11)
[ 18.070856] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.LPCB.LNKU._CRS] (Node da785f7c), AE_TYPE
[ 18.070866] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 18.070873] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 18.070877] ACPI: PCI Interrupt Link [LNKU] (IRQs 9) *0
[ 20.069138] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[ 20.069656] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 20.069682] pnp: PnP ACPI init
[ 21.067958] pnp: PnP ACPI: found 12 devices
[ 21.067964] PnPBIOS: Disabled by ACPI PNP
[ 21.068051] PCI: Using ACPI for IRQ routing
[ 21.068055] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 21.069831] NET: Registered protocol family 8
[ 21.069834] NET: Registered protocol family 20
[ 21.070071] pnp: 00:07: ioport range 0x200-0x20f has been reserved
[ 21.070075] pnp: 00:07: ioport range 0x40b-0x40b has been reserved
[ 21.070078] pnp: 00:07: ioport range 0x480-0x48f has been reserved
[ 21.070081] pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 21.070443] PCI: Bridge: 0000:00:01.0
[ 21.070446] IO window: b000-bfff
[ 21.070451] MEM window: e8500000-e85fffff
[ 21.070455] PREFETCH window: f0000000-f7ffffff
[ 21.070460] PCI: Bus 2, cardbus bridge: 0000:00:0b.0
[ 21.070463] IO window: 00001000-000010ff
[ 21.070467] IO window: 00001400-000014ff
[ 21.070471] PREFETCH window: 20000000-23ffffff
[ 21.070475] MEM window: 24000000-27ffffff
[ 21.070478] PCI: Bus 6, cardbus bridge: 0000:00:0b.1
[ 21.070481] IO window: 00001800-000018ff
[ 21.070484] IO window: 00001c00-00001cff
[ 21.070488] PREFETCH window: 28000000-2bffffff
[ 21.070492] MEM window: 2c000000-2fffffff
[ 21.070699] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 21.070704] PCI: setting IRQ 11 as level-triggered
[ 21.070708] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 21.070884] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[ 21.070887] ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 21.070947] NET: Registered protocol family 2
[ 21.104036] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 21.104212] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 21.104684] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 21.104916] TCP: Hash tables configured (established 16384 bind 8192)
[ 21.104920] TCP reno registered
[ 21.116021] checking if image is initramfs... it is
[ 21.801754] Freeing initrd memory: 6782k freed
[ 21.802540] audit: initializing netlink socket (disabled)
[ 21.802570] audit(1189460112.456:1): initialized
[ 21.802749] VFS: Disk quotas dquot_6.5.1
[ 21.802777] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 21.802865] io scheduler noop registered
[ 21.802869] io scheduler anticipatory registered
[ 21.802872] io scheduler deadline registered
[ 21.802882] io scheduler cfq registered (default)
[ 21.802898] ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb.
[ 22.235107] Activating ISA DMA hang workarounds.
[ 22.235428] isapnp: Scanning for PnP cards...
[ 22.502221] isapnp: No Plug & Play device found
[ 22.533501] Real Time Clock Driver v1.12ac
[ 22.533589] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 22.533780] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 22.534653] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 22.535317] ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
[ 22.535323] ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11
[ 22.536447] 0000:00:03.0: ttyS1 at I/O 0x8428 (irq = 11) is a 8250
[ 22.536985] 0000:00:03.0: ttyS2 at I/O 0x8440 (irq = 11) is a 8250
[ 22.537362] 0000:00:03.0: ttyS3 at I/O 0x8450 (irq = 11) is a 8250
[ 22.537453] Couldn't register serial port 0000:00:03.0: -28
[ 22.537571] mice: PS/2 mouse device common for all mice
[ 22.538431] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 22.538844] input: Macintosh mouse button emulation as /class/input/input0
[ 22.538889] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 22.538973] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 22.539302] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 22.549535] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 22.556507] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 22.556514] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 22.556518] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 22.556521] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 22.556524] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 22.556988] EISA: Probing bus 0 at eisa.0
[ 22.557004] Cannot allocate resource for EISA slot 1
[ 22.557034] Cannot allocate resource for EISA slot 8
[ 22.557036] EISA: Detected 0 cards.
[ 22.587179] TCP cubic registered
[ 22.587189] NET: Registered protocol family 1
[ 22.587230] Using IPI No-Shortcut mode
[ 22.587335] ACPI: (supports S0 S3 S4 S5)
[ 22.587387] Magic number: 7:28:601
[ 22.587550] hash matches device ptyd5
[ 22.588548] Freeing unused kernel memory: 328k freed
[ 22.590865] Time: tsc clocksource has been installed.
[ 22.603062] input: AT Translated Set 2 keyboard as /class/input/input1
[ 23.845943] Capability LSM initialized
[ 23.890300] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 6.016000] Time: acpi_pm clocksource has been installed.
[ 7.968000] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707]
[ 9.968000] ACPI: Thermal Zone [THRM] (68 C)
[ 10.624000] usbcore: registered new interface driver usbfs
[ 10.624000] usbcore: registered new interface driver hub
[ 10.624000] usbcore: registered new device driver usb
[ 10.628000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.628000] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.LPCB.LNKU._CRS] (Node da785f7c), AE_TYPE
[ 10.628000] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 10.628000] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 10.628000] ACPI: Unable to set IRQ for PCI Interrupt Link [LNKU]. Try pci=noacpi or acpi=off
[ 10.628000] ACPI: Invalid IRQ link routing entry
[ 10.628000] ACPI: Unable to derive IRQ for device 0000:00:02.0
[ 10.628000] ACPI: PCI Interrupt 0000:00:02.0[A]: no GSI - using IRQ 11
[ 10.628000] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 10.628000] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[ 10.628000] ohci_hcd 0000:00:02.0: irq 11, io mem 0xe8400000
[ 10.672000] SCSI subsystem initialized
[ 10.676000] libata version 2.20 loaded.
[ 10.708000] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 10.724000] ieee1394: Initialized config rom entry `ip1394'
[ 10.744000] usb usb1: configuration #1 chosen from 1 choice
[ 10.744000] hub 1-0:1.0: USB hub found
[ 10.744000] hub 1-0:1.0: 2 ports detected
[ 10.848000] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
[ 10.848000] PCI: setting IRQ 10 as level-triggered
[ 10.848000] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
[ 10.848000] ohci_hcd 0000:00:0f.0: OHCI Host Controller
[ 10.848000] ohci_hcd 0000:00:0f.0: new USB bus registered, assigned bus number 2
[ 10.848000] ohci_hcd 0000:00:0f.0: irq 10, io mem 0xe8405000
[ 10.904000] usb usb2: configuration #1 chosen from 1 choice
[ 10.904000] hub 2-0:1.0: USB hub found
[ 10.904000] hub 2-0:1.0: 2 ports detected
[ 10.924000] Floppy drive(s): fd0 is 1.44M
[ 10.948000] FDC 0 is a post-1991 82077
[ 11.008000] alim15x3: ATI Radeon IGP Northbridge is not yet fully tested.
[ 11.008000] ALI15X3: IDE controller at PCI slot 0000:00:04.0
[ 11.008000] ACPI: Unable to derive IRQ for device 0000:00:04.0
[ 11.008000] ACPI: PCI Interrupt 0000:00:04.0[A]: no GSI
[ 11.008000] ALI15X3: chipset revision 196
[ 11.008000] ALI15X3: not 100% native mode: will probe irqs later
[ 11.008000] ide0: BM-DMA at 0xa000-0xa007, BIOS settings: hda:DMA, hdb:pio
[ 11.008000] ide1: BM-DMA at 0xa008-0xa00f, BIOS settings: hdc:DMA, hdd:pio
[ 11.008000] Probing IDE interface ide0...
[ 11.300000] hda: FUJITSU MHS2040AT D, ATA DISK drive
[ 12.016000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 12.076000] Probing IDE interface ide1...
[ 12.812000] hdc: QSI CD-RW/DVD-ROM SBW-241, ATAPI CD/DVD-ROM drive
[ 13.148000] ide1 at 0x170-0x177,0x376 on irq 15
[ 13.148000] 8139cp 0000:00:09.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[ 13.148000] 8139cp 0000:00:09.0: Try the "8139too" driver instead.
[ 13.152000] 8139too Fast Ethernet driver 0.9.28
[ 13.152000] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 13.152000] eth0: RealTek RTL8139 at 0xdc846800, 00:02:3f:b5:aa:9a, IRQ 11
[ 13.152000] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 13.152000] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[ 13.152000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[ 13.208000] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[e8406000-e84067ff] Max Packet=[2048] IR/IT contexts=[8/8]
[ 13.224000] hda: max request size: 128KiB
[ 13.236000] hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
[ 13.240000] hda: cache flushes supported
[ 13.240000] hda: hda1 hda2 hda3 < hda5 >
[ 13.288000] hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 13.288000] Uniform CD-ROM driver Revision: 3.20
[ 13.684000] Attempting manual resume
[ 13.684000] swsusp: Resume From Partition 3:5
[ 13.684000] PM: Checking swsusp image.
[ 13.688000] PM: Resume from disk failed.
[ 13.728000] kjournald starting. Commit interval 5 seconds
[ 13.728000] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.488000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f322700129e]
[ 22.812000] floppy0: unexpected interrupt
[ 22.812000] floppy0: sensei repl[0]=2b repl[1]=0
[ 22.812000] floppy0: sensei repl[0]=80
[ 22.812000] floppy0: unexpected interrupt
[ 22.812000] floppy0: sensei repl[0]=c3 repl[1]=0
[ 22.812000] floppy0: sensei repl[0]=80
[ 30.004000] eth0: link down
[ 31.408000] NET: Registered protocol family 17
[ 32.348000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 32.356000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 32.472000] ali15x3_smbus 0000:00:06.0: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
[ 32.472000] ali15x3_smbus 0000:00:06.0: ALI15X3 not detected, module not inserted.
[ 32.636000] Linux agpgart interface v0.102 (c) Dave Jones
[ 32.672000] agpgart: Detected Ati IGP320/M chipset
[ 32.680000] agpgart: AGP aperture is 64M @ 0xec000000
[ 32.728000] Yenta: CardBus bridge found at 0000:00:0b.0 [1734:100a]
[ 32.728000] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 32.728000] Yenta: Routing CardBus interrupts to PCI
[ 32.728000] Yenta TI: socket 0000:00:0b.0, mfunc 0x011c1122, devctl 0x44
[ 32.960000] Yenta: ISA IRQ mask 0x00b8, PCI irq 11
[ 32.960000] Socket status: 30000006
[ 32.960000] Yenta: CardBus bridge found at 0000:00:0b.1 [1734:100a]
[ 32.960000] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 32.960000] Yenta: Routing CardBus interrupts to PCI
[ 32.960000] Yenta TI: socket 0000:00:0b.1, mfunc 0x011c1122, devctl 0x44
[ 33.192000] Yenta: ISA IRQ mask 0x00b8, PCI irq 11
[ 33.192000] Socket status: 30000006
[ 33.196000] input: PC Speaker as /class/input/input2
[ 33.380000] parport: PnPBIOS parport detected.
[ 33.380000] parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 33.772000] input: ImPS/2 Logitech Wheel Mouse as /class/input/input3
[ 33.884000] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
[ 33.884000] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
[ 34.128000] input: PS/2 Mouse as /class/input/input4
[ 34.152000] input: AlpsPS/2 ALPS GlidePoint as /class/input/input5
[ 34.184000] cs: IO port probe 0x100-0x3af: excluding 0x220-0x22f 0x330-0x337 0x388-0x38f
[ 34.188000] cs: IO port probe 0x3e0-0x4ff: clean.
[ 34.188000] cs: IO port probe 0x820-0x8ff: clean.
[ 34.188000] cs: IO port probe 0xc00-0xcf7: clean.
[ 34.188000] cs: IO port probe 0xa00-0xaff: clean.
[ 34.192000] cs: IO port probe 0x100-0x3af: excluding 0x220-0x22f 0x330-0x337 0x388-0x38f
[ 34.192000] cs: IO port probe 0x3e0-0x4ff: clean.
[ 34.196000] cs: IO port probe 0x820-0x8ff: clean.
[ 34.196000] cs: IO port probe 0xc00-0xcf7: clean.
[ 34.196000] cs: IO port probe 0xa00-0xaff: clean.
[ 36.988000] AC'97 1 does not respond - RESET
[ 37.004000] AC'97 1 access is not valid [0xffffffff], removing mixer.
[ 37.004000] ali mixer 1 creating error.
[ 37.236000] fuse init (API version 7.8)
[ 37.292000] lp0: using parport0 (interrupt-driven).
[ 37.360000] Adding 819272k swap on /dev/disk/by-uuid/5280f007-9008-44cc-b3a9-87dba4738eca. Priority:-1 extents:1 across:819272k
[ 37.564000] EXT3 FS on hda2, internal journal
[ 47.464000] ACPI: Battery Slot [BAT1] (battery present)
[ 48.700000] ACPI: AC Adapter [ACAD] (off-line)
[ 48.756000] ibm_acpi: ec object not found
[ 48.784000] Using specific hotkey driver
[ 49.828000] No dock devices found.
[ 49.936000] input: Power Button (FF) as /class/input/input6
[ 49.940000] ACPI: Power Button (FF) [PWRF]
[ 49.980000] input: Lid Switch as /class/input/input7
[ 49.988000] ACPI: Lid Switch [LID]
[ 50.024000] input: Power Button (CM) as /class/input/input8
[ 50.032000] ACPI: Power Button (CM) [PWRB]
[ 50.100000] pcc_acpi: loading...
[ 50.464000] powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
[ 50.472000] powernow: SGTC: 13333
[ 50.472000] powernow: Minimum speed 662 MHz. Maximum speed 1788 MHz.
[ 71.420000] ppdev: user-space parallel port driver
[ 72.016000] mtrr: no more MTRRs available
[ 72.016000] mtrr: no more MTRRs available
[ 72.016000] mtrr: no more MTRRs available
[ 72.016000] mtrr: no more MTRRs available
[ 72.016000] mtrr: no more MTRRs available
[ 73.016000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 73.016000] apm: overridden by ACPI.
[ 73.296000] Bluetooth: Core ver 2.11
[ 73.296000] NET: Registered protocol family 31
[ 73.296000] Bluetooth: HCI device and connection manager initialized
[ 73.296000] Bluetooth: HCI socket layer initialized
[ 73.364000] Bluetooth: L2CAP ver 2.8
[ 73.364000] Bluetooth: L2CAP socket layer initialized
[ 73.496000] Bluetooth: RFCOMM socket layer initialized
[ 73.496000] Bluetooth: RFCOMM TTY layer initialized
[ 73.496000] Bluetooth: RFCOMM ver 1.8
[ 88.592000] NET: Registered protocol family 10
[ 88.592000] lo: Disabled Privacy Extensions
[ 88.592000] ADDRCONF(NETDEV_UP): eth0: link is not ready
questo e' il dmesg dopo l'inserimento della pen
utente@amilo:~$ dmesg
[ 0.000000] Linux version 2.6.20-16-generic (root@terranova) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Fri Aug 31 00:55:27 UTC 2007 (Ubuntu 2.6.20-16.31-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 000000000009f800 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000d0000 size: 0000000000030000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000001bdf0000 end: 000000001bef0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000001bef0000 size: 000000000000f000 end: 000000001beff000 type: 3
[ 0.000000] copy_e820_map() start: 000000001beff000 size: 0000000000001000 end: 000000001bf00000 type: 4
[ 0.000000] copy_e820_map() start: 000000001bf00000 size: 0000000000100000 end: 000000001c000000 type: 2
[ 0.000000] copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001bef0000 (usable)
[ 0.000000] BIOS-e820: 000000001bef0000 - 000000001beff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001beff000 - 000000001bf00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001bf00000 - 000000001c000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 446MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 114416) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 114416
[ 0.000000] HighMem 114416 -> 114416
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 114416
[ 0.000000] On node 0 totalpages: 114416
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 861 pages used for memmap
[ 0.000000] Normal zone: 109459 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP (v000 PTLTD ) @ 0x000f7790
[ 0.000000] ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1befbc0a
[ 0.000000] ACPI: FADT (v001 ATI Raptor 0x06040000 ATI 0x000f4240) @ 0x1befee7b
[ 0.000000] ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x1befeeef
[ 0.000000] ACPI: DSDT (v001 COMPAL CY26____ 0x06040000 MSFT 0x0100000e) @ 0x00000000
[ 0.000000] ATI board detected. Disabling timer routing over 8254.
[ 0.000000] ACPI: PM-Timer IO Port: 0x8008
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 1c000000:e3f80000)
[ 0.000000] Detected 1788.898 MHz processor.
[ 17.438341] Built 1 zonelists. Total pages: 113523
[ 17.438348] Kernel command line: root=UUID=dd24c613-8075-4f1d-a65c-194d862fa3f0 ro quiet splash locale=it_IT
[ 17.438559] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 17.438577] mapped APIC to ffffd000 (0138a000)
[ 17.438583] Enabling fast FPU save and restore... done.
[ 17.438586] Enabling unmasked SIMD FPU exception support... done.
[ 17.438607] Initializing CPU#0
[ 17.438720] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 17.440356] Console: colour VGA+ 80x25
[ 17.441248] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 17.441728] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 17.465049] Memory: 442680k/457664k available (1993k kernel code, 14468k reserved, 900k data, 328k init, 0k highmem)
[ 17.465063] virtual kernel memory layout:
[ 17.465064] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 17.465066] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 17.465067] vmalloc : 0xdc800000 - 0xff7fe000 ( 559 MB)
[ 17.465069] lowmem : 0xc0000000 - 0xdbef0000 ( 446 MB)
[ 17.465070] .init : 0xc03d9000 - 0xc042b000 ( 328 kB)
[ 17.465072] .data : 0xc02f2434 - 0xc03d36d4 ( 900 kB)
[ 17.465073] .text : 0xc0100000 - 0xc02f2434 (1993 kB)
[ 17.465077] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 17.542652] Calibrating delay using timer specific routine.. 3579.78 BogoMIPS (lpj=7159574)
[ 17.542723] Security Framework v1.0.0 initialized
[ 17.542736] SELinux: Disabled at boot.
[ 17.542761] Mount-cache hash table entries: 512
[ 17.543017] CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000
[ 17.543030] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 17.543033] CPU: L2 Cache: 512K (64 bytes/line)
[ 17.543037] CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000420 00000000 00000000 00000000
[ 17.543052] Compat vDSO mapped to ffffe000.
[ 17.543061] Remapping vsyscall page to ffffe000
[ 17.543077] Checking 'hlt' instruction... OK.
[ 17.558869] SMP alternatives: switching to UP code
[ 17.559314] Freeing SMP alternatives: 11k freed
[ 17.559671] Early unpacking initramfs... done
[ 17.932724] ACPI: Core revision 20060707
[ 17.936481] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[ 17.938054] ACPI: setting ELCR to 0200 (from 0c20)
[ 18.035889] CPU0: AMD mobile AMD Athlon (tm) 2400+ stepping 00
[ 18.035899] SMP motherboard not detected.
[ 18.035903] Local APIC not detected. Using dummy APIC emulation.
[ 18.035992] Brought up 1 CPUs
[ 18.036442] Booting paravirtualized kernel on bare hardware
[ 18.036574] Time: 21:35:08 Date: 08/10/107
[ 18.036639] NET: Registered protocol family 16
[ 18.036822] EISA bus registered
[ 18.036829] ACPI: bus type pci registered
[ 18.059320] PCI: PCI BIOS revision 2.10 entry at 0xfd85e, last bus=1
[ 18.059323] PCI: Using configuration type 1
[ 18.059326] Setting up standard PCI resources
[ 18.065509] ACPI: Interpreter enabled
[ 18.065512] ACPI: Using PIC for interrupt routing
[ 18.066012] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 18.066020] PCI: Probing PCI hardware (bus 00)
[ 18.066070] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[ 18.066603] PCI quirk: region 8000-803f claimed by ali7101 ACPI
[ 18.066607] PCI quirk: region 8040-805f claimed by ali7101 SMB
[ 18.066923] Boot video device is 0000:01:05.0
[ 18.067058] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 18.069045] ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
[ 18.069273] ACPI: PCI Interrupt Link [LNKB] (IRQs *11)
[ 18.069498] ACPI: PCI Interrupt Link [LNKC] (IRQs 10) *5
[ 18.069722] ACPI: PCI Interrupt Link [LNKD] (IRQs 10) *0, disabled.
[ 18.069946] ACPI: PCI Interrupt Link [LNKE] (IRQs 5 9 *10 11)
[ 18.070171] ACPI: PCI Interrupt Link [LNKF] (IRQs 5 9 10 11) *0, disabled.
[ 18.070405] ACPI: PCI Interrupt Link [LNKG] (IRQs 5 9 10 *11)
[ 18.070629] ACPI: PCI Interrupt Link [LNKH] (IRQs 5 9 10 *11)
[ 18.070856] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.LPCB.LNKU._CRS] (Node da785f7c), AE_TYPE
[ 18.070866] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 18.070873] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 18.070877] ACPI: PCI Interrupt Link [LNKU] (IRQs 9) *0
[ 20.069138] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[ 20.069656] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 20.069682] pnp: PnP ACPI init
[ 21.067958] pnp: PnP ACPI: found 12 devices
[ 21.067964] PnPBIOS: Disabled by ACPI PNP
[ 21.068051] PCI: Using ACPI for IRQ routing
[ 21.068055] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 21.069831] NET: Registered protocol family 8
[ 21.069834] NET: Registered protocol family 20
[ 21.070071] pnp: 00:07: ioport range 0x200-0x20f has been reserved
[ 21.070075] pnp: 00:07: ioport range 0x40b-0x40b has been reserved
[ 21.070078] pnp: 00:07: ioport range 0x480-0x48f has been reserved
[ 21.070081] pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 21.070443] PCI: Bridge: 0000:00:01.0
[ 21.070446] IO window: b000-bfff
[ 21.070451] MEM window: e8500000-e85fffff
[ 21.070455] PREFETCH window: f0000000-f7ffffff
[ 21.070460] PCI: Bus 2, cardbus bridge: 0000:00:0b.0
[ 21.070463] IO window: 00001000-000010ff
[ 21.070467] IO window: 00001400-000014ff
[ 21.070471] PREFETCH window: 20000000-23ffffff
[ 21.070475] MEM window: 24000000-27ffffff
[ 21.070478] PCI: Bus 6, cardbus bridge: 0000:00:0b.1
[ 21.070481] IO window: 00001800-000018ff
[ 21.070484] IO window: 00001c00-00001cff
[ 21.070488] PREFETCH window: 28000000-2bffffff
[ 21.070492] MEM window: 2c000000-2fffffff
[ 21.070699] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 21.070704] PCI: setting IRQ 11 as level-triggered
[ 21.070708] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 21.070884] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[ 21.070887] ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 21.070947] NET: Registered protocol family 2
[ 21.104036] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 21.104212] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 21.104684] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 21.104916] TCP: Hash tables configured (established 16384 bind 8192)
[ 21.104920] TCP reno registered
[ 21.116021] checking if image is initramfs... it is
[ 21.801754] Freeing initrd memory: 6782k freed
[ 21.802540] audit: initializing netlink socket (disabled)
[ 21.802570] audit(1189460112.456:1): initialized
[ 21.802749] VFS: Disk quotas dquot_6.5.1
[ 21.802777] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 21.802865] io scheduler noop registered
[ 21.802869] io scheduler anticipatory registered
[ 21.802872] io scheduler deadline registered
[ 21.802882] io scheduler cfq registered (default)
[ 21.802898] ATI Northbridge, reserving I/O ports 0x3b0 to 0x3bb.
[ 22.235107] Activating ISA DMA hang workarounds.
[ 22.235428] isapnp: Scanning for PnP cards...
[ 22.502221] isapnp: No Plug & Play device found
[ 22.533501] Real Time Clock Driver v1.12ac
[ 22.533589] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 22.533780] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 22.534653] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 22.535317] ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
[ 22.535323] ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11
[ 22.536447] 0000:00:03.0: ttyS1 at I/O 0x8428 (irq = 11) is a 8250
[ 22.536985] 0000:00:03.0: ttyS2 at I/O 0x8440 (irq = 11) is a 8250
[ 22.537362] 0000:00:03.0: ttyS3 at I/O 0x8450 (irq = 11) is a 8250
[ 22.537453] Couldn't register serial port 0000:00:03.0: -28
[ 22.537571] mice: PS/2 mouse device common for all mice
[ 22.538431] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 22.538844] input: Macintosh mouse button emulation as /class/input/input0
[ 22.538889] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 22.538973] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 22.539302] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 22.549535] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 22.556507] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 22.556514] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 22.556518] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 22.556521] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 22.556524] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 22.556988] EISA: Probing bus 0 at eisa.0
[ 22.557004] Cannot allocate resource for EISA slot 1
[ 22.557034] Cannot allocate resource for EISA slot 8
[ 22.557036] EISA: Detected 0 cards.
[ 22.587179] TCP cubic registered
[ 22.587189] NET: Registered protocol family 1
[ 22.587230] Using IPI No-Shortcut mode
[ 22.587335] ACPI: (supports S0 S3 S4 S5)
[ 22.587387] Magic number: 7:28:601
[ 22.587550] hash matches device ptyd5
[ 22.588548] Freeing unused kernel memory: 328k freed
[ 22.590865] Time: tsc clocksource has been installed.
[ 22.603062] input: AT Translated Set 2 keyboard as /class/input/input1
[ 23.845943] Capability LSM initialized
[ 23.890300] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 6.016000] Time: acpi_pm clocksource has been installed.
[ 7.968000] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707]
[ 9.968000] ACPI: Thermal Zone [THRM] (68 C)
[ 10.624000] usbcore: registered new interface driver usbfs
[ 10.624000] usbcore: registered new interface driver hub
[ 10.624000] usbcore: registered new device driver usb
[ 10.628000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.628000] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.LPCB.LNKU._CRS] (Node da785f7c), AE_TYPE
[ 10.628000] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 10.628000] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 10.628000] ACPI: Unable to set IRQ for PCI Interrupt Link [LNKU]. Try pci=noacpi or acpi=off
[ 10.628000] ACPI: Invalid IRQ link routing entry
[ 10.628000] ACPI: Unable to derive IRQ for device 0000:00:02.0
[ 10.628000] ACPI: PCI Interrupt 0000:00:02.0[A]: no GSI - using IRQ 11
[ 10.628000] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 10.628000] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[ 10.628000] ohci_hcd 0000:00:02.0: irq 11, io mem 0xe8400000
[ 10.672000] SCSI subsystem initialized
[ 10.676000] libata version 2.20 loaded.
[ 10.708000] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 10.724000] ieee1394: Initialized config rom entry `ip1394'
[ 10.744000] usb usb1: configuration #1 chosen from 1 choice
[ 10.744000] hub 1-0:1.0: USB hub found
[ 10.744000] hub 1-0:1.0: 2 ports detected
[ 10.848000] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
[ 10.848000] PCI: setting IRQ 10 as level-triggered
[ 10.848000] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
[ 10.848000] ohci_hcd 0000:00:0f.0: OHCI Host Controller
[ 10.848000] ohci_hcd 0000:00:0f.0: new USB bus registered, assigned bus number 2
[ 10.848000] ohci_hcd 0000:00:0f.0: irq 10, io mem 0xe8405000
[ 10.904000] usb usb2: configuration #1 chosen from 1 choice
[ 10.904000] hub 2-0:1.0: USB hub found
[ 10.904000] hub 2-0:1.0: 2 ports detected
[ 10.924000] Floppy drive(s): fd0 is 1.44M
[ 10.948000] FDC 0 is a post-1991 82077
[ 11.008000] alim15x3: ATI Radeon IGP Northbridge is not yet fully tested.
[ 11.008000] ALI15X3: IDE controller at PCI slot 0000:00:04.0
[ 11.008000] ACPI: Unable to derive IRQ for device 0000:00:04.0
[ 11.008000] ACPI: PCI Interrupt 0000:00:04.0[A]: no GSI
[ 11.008000] ALI15X3: chipset revision 196
[ 11.008000] ALI15X3: not 100% native mode: will probe irqs later
[ 11.008000] ide0: BM-DMA at 0xa000-0xa007, BIOS settings: hda:DMA, hdb:pio
[ 11.008000] ide1: BM-DMA at 0xa008-0xa00f, BIOS settings: hdc:DMA, hdd:pio
[ 11.008000] Probing IDE interface ide0...
[ 11.300000] hda: FUJITSU MHS2040AT D, ATA DISK drive
[ 12.016000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 12.076000] Probing IDE interface ide1...
[ 12.812000] hdc: QSI CD-RW/DVD-ROM SBW-241, ATAPI CD/DVD-ROM drive
[ 13.148000] ide1 at 0x170-0x177,0x376 on irq 15
[ 13.148000] 8139cp 0000:00:09.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[ 13.148000] 8139cp 0000:00:09.0: Try the "8139too" driver instead.
[ 13.152000] 8139too Fast Ethernet driver 0.9.28
[ 13.152000] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
[ 13.152000] eth0: RealTek RTL8139 at 0xdc846800, 00:02:3f:b5:aa:9a, IRQ 11
[ 13.152000] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 13.152000] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[ 13.152000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[ 13.208000] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[e8406000-e84067ff] Max Packet=[2048] IR/IT contexts=[8/8]
[ 13.224000] hda: max request size: 128KiB
[ 13.236000] hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
[ 13.240000] hda: cache flushes supported
[ 13.240000] hda: hda1 hda2 hda3 < hda5 >
[ 13.288000] hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 13.288000] Uniform CD-ROM driver Revision: 3.20
[ 13.684000] Attempting manual resume
[ 13.684000] swsusp: Resume From Partition 3:5
[ 13.684000] PM: Checking swsusp image.
[ 13.688000] PM: Resume from disk failed.
[ 13.728000] kjournald starting. Commit interval 5 seconds
[ 13.728000] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.488000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f322700129e]
[ 22.812000] floppy0: unexpected interrupt
[ 22.812000] floppy0: sensei repl[0]=2b repl[1]=0
[ 22.812000] floppy0: sensei repl[0]=80
[ 22.812000] floppy0: unexpected interrupt
[ 22.812000] floppy0: sensei repl[0]=c3 repl[1]=0
[ 22.812000] floppy0: sensei repl[0]=80
[ 30.004000] eth0: link down
[ 31.408000] NET: Registered protocol family 17
[ 32.348000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 32.356000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 32.472000] ali15x3_smbus 0000:00:06.0: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr
[ 32.472000] ali15x3_smbus 0000:00:06.0: ALI15X3 not detected, module not inserted.
[ 32.636000] Linux agpgart interface v0.102 (c) Dave Jones
[ 32.672000] agpgart: Detected Ati IGP320/M chipset
[ 32.680000] agpgart: AGP aperture is 64M @ 0xec000000
[ 32.728000] Yenta: CardBus bridge found at 0000:00:0b.0 [1734:100a]
[ 32.728000] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 32.728000] Yenta: Routing CardBus interrupts to PCI
[ 32.728000] Yenta TI: socket 0000:00:0b.0, mfunc 0x011c1122, devctl 0x44
[ 32.960000] Yenta: ISA IRQ mask 0x00b8, PCI irq 11
[ 32.960000] Socket status: 30000006
[ 32.960000] Yenta: CardBus bridge found at 0000:00:0b.1 [1734:100a]
[ 32.960000] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 32.960000] Yenta: Routing CardBus interrupts to PCI
[ 32.960000] Yenta TI: socket 0000:00:0b.1, mfunc 0x011c1122, devctl 0x44
[ 33.192000] Yenta: ISA IRQ mask 0x00b8, PCI irq 11
[ 33.192000] Socket status: 30000006
[ 33.196000] input: PC Speaker as /class/input/input2
[ 33.380000] parport: PnPBIOS parport detected.
[ 33.380000] parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 33.772000] input: ImPS/2 Logitech Wheel Mouse as /class/input/input3
[ 33.884000] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
[ 33.884000] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
[ 34.128000] input: PS/2 Mouse as /class/input/input4
[ 34.152000] input: AlpsPS/2 ALPS GlidePoint as /class/input/input5
[ 34.184000] cs: IO port probe 0x100-0x3af: excluding 0x220-0x22f 0x330-0x337 0x388-0x38f
[ 34.188000] cs: IO port probe 0x3e0-0x4ff: clean.
[ 34.188000] cs: IO port probe 0x820-0x8ff: clean.
[ 34.188000] cs: IO port probe 0xc00-0xcf7: clean.
[ 34.188000] cs: IO port probe 0xa00-0xaff: clean.
[ 34.192000] cs: IO port probe 0x100-0x3af: excluding 0x220-0x22f 0x330-0x337 0x388-0x38f
[ 34.192000] cs: IO port probe 0x3e0-0x4ff: clean.
[ 34.196000] cs: IO port probe 0x820-0x8ff: clean.
[ 34.196000] cs: IO port probe 0xc00-0xcf7: clean.
[ 34.196000] cs: IO port probe 0xa00-0xaff: clean.
[ 36.988000] AC'97 1 does not respond - RESET
[ 37.004000] AC'97 1 access is not valid [0xffffffff], removing mixer.
[ 37.004000] ali mixer 1 creating error.
[ 37.236000] fuse init (API version 7.8)
[ 37.292000] lp0: using parport0 (interrupt-driven).
[ 37.360000] Adding 819272k swap on /dev/disk/by-uuid/5280f007-9008-44cc-b3a9-87dba4738eca. Priority:-1 extents:1 across:819272k
[ 37.564000] EXT3 FS on hda2, internal journal
[ 47.464000] ACPI: Battery Slot [BAT1] (battery present)
[ 48.700000] ACPI: AC Adapter [ACAD] (off-line)
[ 48.756000] ibm_acpi: ec object not found
[ 48.784000] Using specific hotkey driver
[ 49.828000] No dock devices found.
[ 49.936000] input: Power Button (FF) as /class/input/input6
[ 49.940000] ACPI: Power Button (FF) [PWRF]
[ 49.980000] input: Lid Switch as /class/input/input7
[ 49.988000] ACPI: Lid Switch [LID]
[ 50.024000] input: Power Button (CM) as /class/input/input8
[ 50.032000] ACPI: Power Button (CM) [PWRB]
[ 50.100000] pcc_acpi: loading...
[ 50.464000] powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
[ 50.472000] powernow: SGTC: 13333
[ 50.472000] powernow: Minimum speed 662 MHz. Maximum speed 1788 MHz.
[ 71.420000] ppdev: user-space parallel port driver
[ 72.016000] mtrr: no more MTRRs available
[ 72.016000] mtrr: no more MTRRs available
[ 72.016000] mtrr: no more MTRRs available
[ 72.016000] mtrr: no more MTRRs available
[ 72.016000] mtrr: no more MTRRs available
[ 73.016000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 73.016000] apm: overridden by ACPI.
[ 73.296000] Bluetooth: Core ver 2.11
[ 73.296000] NET: Registered protocol family 31
[ 73.296000] Bluetooth: HCI device and connection manager initialized
[ 73.296000] Bluetooth: HCI socket layer initialized
[ 73.364000] Bluetooth: L2CAP ver 2.8
[ 73.364000] Bluetooth: L2CAP socket layer initialized
[ 73.496000] Bluetooth: RFCOMM socket layer initialized
[ 73.496000] Bluetooth: RFCOMM TTY layer initialized
[ 73.496000] Bluetooth: RFCOMM ver 1.8
[ 88.592000] NET: Registered protocol family 10
[ 88.592000] lo: Disabled Privacy Extensions
[ 88.592000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 141.476000] irq 9: nobody cared (try booting with the "irqpoll" option)
[ 141.476000] [<c0154334>] __report_bad_irq+0x24/0x80
[ 141.476000] [<c01545ee>] note_interrupt+0x25e/0x290
[ 141.476000] [<c020c762>] acpi_irq+0xb/0x14
[ 141.476000] [<c0153860>] handle_IRQ_event+0x30/0x60
[ 141.476000] [<c015516b>] handle_level_irq+0xeb/0x120
[ 141.476000] [<c0105b70>] do_IRQ+0x40/0x80
[ 141.476000] [<c0104233>] common_interrupt+0x23/0x30
[ 141.476000] [<c012b401>] __do_softirq+0x61/0x100
[ 141.476000] [<c012b4f5>] do_softirq+0x55/0x60
[ 141.476000] [<c0105b75>] do_IRQ+0x45/0x80
[ 141.476000] [<c0104233>] common_interrupt+0x23/0x30
[ 141.476000] [<dc8325bd>] acpi_processor_idle+0x0/0x3f7 [processor]
[ 141.476000] [<dc8327e8>] acpi_processor_idle+0x22b/0x3f7 [processor]
[ 141.476000] [<c0101409>] cpu_idle+0x49/0xd0
[ 141.476000] [<c03d97f5>] start_kernel+0x365/0x420
[ 141.476000] [<c03d9230>] unknown_bootoption+0x0/0x260
[ 141.476000] =======================
[ 141.476000] handlers:
[ 141.476000] [<c020c757>] (acpi_irq+0x0/0x14)
[ 141.476000] Disabling IRQ #9
ilsensine
10-09-2007, 21:27
ho aggiunto iquesti parametri acpi=noirq pci=noacpi nella riga di avvio del kernel all'interno del file /boot/grub/menu.lst
Sbagli qualcosa, non vengono passati al kernel:
[ 17.438348] Kernel command line: root=UUID=dd24c613-8075-4f1d-a65c-194d862fa3f0 ro quiet splash locale=it_IT
Devono comparire nell'elenco.
Il dmesg mostra una cosa che temevo, un "nobody cared"...probabilmente al driver usb non è stato comunicato che il suo irq è il 9.
Cerca di risolvere il problema sulla command line, così puoi sperimentare con le varie opzioni. Non è necessario modificare menu.lst, puoi modificare la riga di boot direttamente da grub (il tasto magico per editare una entry è "e", il tasto per il boot di una entry modificata è "b"; se il tuo grub è la versione grafica, potrebbe essere necessario premere esc all'avvio).
Senti, intanto che segui i consigli del Pinguino Mutante qua sopra, allega la Dsdt che vedo di darci una ravanata io ;)
ilsensine
10-09-2007, 22:07
Senti, intanto che segui i consigli del Pinguino Mutante qua sopra, allega la Dsdt che vedo di darci una ravanata io ;)
Sì, anche perché il problema è lì...disabilitando l'acpi è una pezza, e su un portatile può dare altri problemi.
Ti viene in mente niente per questo?
[ 18.070856] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.LPCB.LNKU._CRS] (Node da785f7c), AE_TYPE
[ 18.070866] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 18.070873] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 18.070877] ACPI: PCI Interrupt Link [LNKU] (IRQs 9) *0
Senti, intanto che segui i consigli del Pinguino Mutante qua sopra, allega la Dsdt che vedo di darci una ravanata io ;)
eccola (http://www.hwupgrade.it/forum/showpost.php?p=18631112&postcount=24): ho postato le righe con gli errori
non l'ho postata tutta perche' sono piu' i tremila righe ... ma posso allegarla
ragazzi vi ringrazio di cuore per l'assistenza :) :)
Qualcuno ha ordinato una dsdt corretta? :sofico:
Qualcuno ha ordinato una dsdt corretta? :sofico:
grazie grazie grazie :):):)
FUNZIONA TUTTO
non ho parole per ringraziarvi,
SIETE GRANDI
grazie Cobra78 e grazie ilsensine
da solo non ci sarei mai riuscito
sachamuni
17-09-2007, 12:33
Cobra78 mi dai una mano con il mio DSDT ?Ho 1 solo errore...questo
dsdt.dsl 4218: Return (Local1)
Error 4049 - ^ Method local variable not initialized (Local1)
ASL Input: dsdt.dsl - 7148 lines, 264803 bytes, 2920 keywords
Compilation complete. 1 Errors, 0 Warnings, 0 Remarks, 1034 Optimizations
allego il dsdt.dsl compresso .
Ciao :help:
Cobra78 mi dai una mano con il mio DSDT ?Ho 1 solo errore...questo
dsdt.dsl 4218: Return (Local1)
Error 4049 - ^ Method local variable not initialized (Local1)
ASL Input: dsdt.dsl - 7148 lines, 264803 bytes, 2920 keywords
Compilation complete. 1 Errors, 0 Warnings, 0 Remarks, 1034 Optimizations
allego il dsdt.dsl compresso .
Ciao :help:
Per un errorino così potresti provare a infilarlo su google, che è ne più ne meno quello che faccio io, condendo il tutto con un po' di buonsenso :P
sachamuni
17-09-2007, 19:50
Per un errorino così potresti provare a infilarlo su google, che è ne più ne meno quello che faccio io, condendo il tutto con un po' di buonsenso :P
Infatti è così che sono arrivato in questo forum! Messo in ricerca google :"dsdt error 4049" e il 3 risultato è portatile e problema con usb - Pagina 2 - Hardware Upgrade Forum
dsdt.dsl 775: Return (Local0) Error 4049 - ^ Method local variable is not initialized (Local0)
Ho passato più di un'ora a leggere altri pagine in rete,poi sono tornato a questo,dove ho visto che c'era qualcuno che aveva già risolto questo stesso errore(tu per ascks).
Tra l'altro questo non era l'unico errore al primo tentativo di compilazione:ne avevo 3,e gli altri 2 li ho risolti googlando.Per questo non trovo niente...
Ciao Sacha
Infatti è così che sono arrivato in questo forum! Messo in ricerca google :"dsdt error 4049" e il 3 risultato è portatile e problema con usb - Pagina 2 - Hardware Upgrade Forum
dsdt.dsl 775: Return (Local0) Error 4049 - ^ Method local variable is not initialized (Local0)
Ho passato più di un'ora a leggere altri pagine in rete,poi sono tornato a questo,dove ho visto che c'era qualcuno che aveva già risolto questo stesso errore(tu per ascks).
Tra l'altro questo non era l'unico errore al primo tentativo di compilazione:ne avevo 3,e gli altri 2 li ho risolti googlando.Per questo non trovo niente...
Ciao Sacha
Uccavoli, si hai ragione ora ricordo, quello è l'errore che mi ha dato più da fare.
Guarda se vuoi allegami al dsdt e vedo di sistemarlo, ma ti avviso che ci vorrà un po', sono un tantino impegnato in sti giorni.
sachamuni
18-09-2007, 08:45
Guarda se vuoi allegami al dsdt e vedo di sistemarlo, ma ti avviso che ci vorrà un po', sono un tantino impegnato in sti giorni.[/QUOTE]
Ti ringrazio, mi dispiace rompere ma è che sono newbie e ho dei gravi problemi con la gestione delle risorse energetiche del pc e in rete non si trova la soluzione e questo errore
Spero proprio che con la nuova dsdt le cose vadano a posto....
Ciao
Sacha
Ti è andata bene, stavolta era semplice....
Qui c'è il sorgente corretto, compila, infilalo nell'initramfs come hai visto e incrocia le dita.
sachamuni
18-09-2007, 17:58
GRAZIE Cobra78 !!!!
Sei stato molto gentile....provo subito!
:D
Ciao
vBulletin® v3.6.4, Copyright ©2000-2025, Jelsoft Enterprises Ltd.