ilsensine
31-07-2007, 08:05
ho cerkato il driver per la mia scheda video realtek hd audio e installandola da terminale mi da vari errori ...
La Realtek se non ricordo male è un clone di quella Intel, i driver dovrebbero esserci. Per la webcam, dobbiamo vedere di cosa si tratta.
Puoi eseguire da una console questi comandi in fila:
/sbin/lsmod > report.txt
dmesg >> report.txt
lsusb >> report.txt
lspci >> report.txt
lspci -n >> report.txt
e allegare il file report.txt che viene creato?
La Realtek se non ricordo male è un clone di quella Intel, i driver dovrebbero esserci. Per la webcam, dobbiamo vedere di cosa si tratta.
Puoi eseguire da una console questi comandi in fila:
/sbin/lsmod > report.txt
dmesg >> report.txt
lsusb >> report.txt
lspci >> report.txt
lspci -n >> report.txt
e allegare il file report.txt che viene creato?[/QUOTE]
:S noni riesko ad allegare il file e quindi te li posto
Module Size Used by
binfmt_misc 12680 1
rfcomm 40856 0
l2cap 25856 5 rfcomm
bluetooth 55908 4 rfcomm,l2cap
ppdev 10116 0
powernow_k8 16064 2
cpufreq_stats 7360 0
cpufreq_ondemand 9228 1
cpufreq_conservative 8200 0
freq_table 5792 3 powernow_k8,cpufreq_stats,cpufreq_ondemand
cpufreq_powersave 2688 0
cpufreq_userspace 5408 0
pcc_acpi 13184 0
tc1100_wmi 8068 0
dev_acpi 12292 0
sony_acpi 6284 0
ac 6020 0
sbs 15652 0
asus_acpi 17308 0
dock 10268 0
video 16388 0
container 5248 0
i2c_ec 6016 1 sbs
backlight 7040 1 asus_acpi
battery 10756 0
button 8720 0
ipv6 268960 12
parport_pc 36388 0
lp 12452 0
parport 36936 3 ppdev,parport_pc,lp
fuse 46612 0
snd_hda_intel 21912 1
snd_hda_codec 205056 1 snd_hda_intel
snd_pcm_oss 44544 0
snd_mixer_oss 17408 2 snd_pcm_oss
joydev 10816 0
snd_pcm 79876 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_dummy 4740 0
snd_seq_oss 32896 0
snd_seq_midi 9600 0
snd_rawmidi 25472 1 snd_seq_midi
wlan_scan_sta 14976 1
snd_seq_midi_event 8448 2 snd_seq_oss,snd_seq_midi
snd_seq 52592 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
ath_rate_sample 14080 1
cdc_ether 6784 0
usbnet 19720 1 cdc_ether
snd_timer 23684 2 snd_pcm,snd_seq
snd_seq_device 9100 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
ath_pci 97312 0
nvidia 6837140 32
pcspkr 4224 0
wlan 204868 4 wlan_scan_sta,ath_rate_sample,ath_pci
mii 6528 1 usbnet
ath_hal 192592 3 ath_rate_sample,ath_pci
psmouse 38920 0
serio_raw 7940 0
agpgart 35400 1 nvidia
k8temp 6656 0
snd 54020 10 snd_hda_intel,snd_hda_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 8672 2 snd
snd_page_alloc 10888 2 snd_hda_intel,snd_pcm
af_packet 23816 10
shpchp 34324 0
pci_hotplug 32576 1 shpchp
i2c_nforce2 6784 0
i2c_core 22656 3 i2c_ec,nvidia,i2c_nforce2
tsdev 8768 0
evdev 11008 5
ext3 133128 1
jbd 59816 1 ext3
mbcache 9604 1 ext3
sg 36252 0
sd_mod 23428 3
ide_cd 32672 0
cdrom 37664 1 ide_cd
ata_generic 9092 0
sata_nv 20868 2
libata 125720 2 ata_generic,sata_nv
ohci_hcd 22532 0
ehci_hcd 34188 0
forcedeth 46728 0
scsi_mod 142348 3 sg,sd_mod,libata
amd74xx 15260 0 [permanent]
generic 5124 0 [permanent]
usbcore 134280 5 cdc_ether,usbnet,ohci_hcd,ehci_hcd
thermal 14856 0
processor 31048 2 powernow_k8,thermal
fan 5636 0
fbcon 42656 0
tileblit 3584 1 fbcon
font 9216 1 fbcon
bitblit 6912 1 fbcon
softcursor 3200 1 bitblit
vesafb 9220 0
capability 5896 0
commoncap 8192 1 capability
[ 0.000000] Linux version 2.6.20-16-generic (root@terranova) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Thu Jun 7 20:19:32 UTC 2007 (Ubuntu 2.6.20-16.29-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000e0000 size: 0000000000020000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000007dec0000 end: 000000007dfc0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000007dfc0000 size: 000000000000e000 end: 000000007dfce000 type: 3
[ 0.000000] copy_e820_map() start: 000000007dfce000 size: 0000000000022000 end: 000000007dff0000 type: 4
[ 0.000000] copy_e820_map() start: 000000007dff0000 size: 0000000000010000 end: 000000007e000000 type: 2
[ 0.000000] copy_e820_map() start: 00000000fec00000 size: 0000000000001000 end: 00000000fec01000 type: 2
[ 0.000000] copy_e820_map() start: 00000000fee00000 size: 0000000000100000 end: 00000000fef00000 type: 2
[ 0.000000] copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007dfc0000 (usable)
[ 0.000000] BIOS-e820: 000000007dfc0000 - 000000007dfce000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007dfce000 - 000000007dff0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007dff0000 - 000000007e000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 1119MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000ff780
[ 0.000000] Entering add_active_range(0, 0, 516032) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 516032
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 516032
[ 0.000000] On node 0 totalpages: 516032
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2239 pages used for memmap
[ 0.000000] HighMem zone: 284417 pages, LIFO batch:31
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP (v000 ACPIAM ) @ 0x000fc400
[ 0.000000] ACPI: RSDT (v001 A M I OEMRSDT 0x10000611 MSFT 0x00000097) @ 0x7dfc0000
[ 0.000000] ACPI: FADT (v002 A M I OEMFACP 0x10000611 MSFT 0x00000097) @ 0x7dfc0200
[ 0.000000] ACPI: MADT (v001 A M I OEMAPIC 0x10000611 MSFT 0x00000097) @ 0x7dfc0390
[ 0.000000] ACPI: MCFG (v001 A M I OEMMCFG 0x10000611 MSFT 0x00000097) @ 0x7dfc0400
[ 0.000000] ACPI: OEMB (v001 A M I AMI_OEM 0x10000611 MSFT 0x00000097) @ 0x7dfce040
[ 0.000000] ACPI: DSDT (v001 A0427 A0427000 0x00000000 INTL 0x02002026) @ 0x00000000
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] ACPI: PM-Timer IO Port: 0x508
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:8 APIC version 16
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:8 APIC version 16
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: BIOS IRQ0 pin2 override ignored.
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 7e000000:80c00000)
[ 0.000000] Detected 1607.448 MHz processor.
[ 13.788575] Built 1 zonelists. Total pages: 512001
[ 13.788579] Kernel command line: root=UUID=f7beaca9-e66c-4a25-9e8b-dba8e2dd554e ro quiet splash
[ 13.788732] mapped APIC to ffffd000 (fee00000)
[ 13.788735] mapped IOAPIC to ffffc000 (fec00000)
[ 13.788738] Enabling fast FPU save and restore... done.
[ 13.788741] Enabling unmasked SIMD FPU exception support... done.
[ 13.788748] Initializing CPU#0
[ 13.788808] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 13.788899] spurious 8259A interrupt: IRQ7.
[ 13.792428] Console: colour VGA+ 80x25
[ 13.792756] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 13.793174] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 13.864330] Memory: 2035284k/2064128k available (1992k kernel code, 27472k reserved, 900k data, 328k init, 1146624k highmem)
[ 13.864342] virtual kernel memory layout:
[ 13.864344] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 13.864345] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 13.864347] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 13.864348] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 13.864350] .init : 0xc03d9000 - 0xc042b000 ( 328 kB)
[ 13.864351] .data : 0xc02f2374 - 0xc03d36d4 ( 900 kB)
[ 13.864353] .text : 0xc0100000 - 0xc02f2374 (1992 kB)
[ 13.864356] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 13.940804] Calibrating delay using timer specific routine.. 3217.93 BogoMIPS (lpj=6435877)
[ 13.940845] Security Framework v1.0.0 initialized
[ 13.940850] SELinux: Disabled at boot.
[ 13.940867] Mount-cache hash table entries: 512
[ 13.940994] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f
[ 13.941004] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 13.941007] CPU: L2 Cache: 512K (64 bytes/line)
[ 13.941010] CPU 0(2) -> Core 0
[ 13.941012] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f
[ 13.941023] Compat vDSO mapped to ffffe000.
[ 13.941027] Remapping vsyscall page to ffffe000
[ 13.941037] Checking 'hlt' instruction... OK.
[ 13.956939] SMP alternatives: switching to UP code
[ 13.957301] Early unpacking initramfs... done
[ 14.305696] ACPI: Core revision 20060707
[ 14.306181] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[ 14.311388] CPU0: AMD Turion(tm) 64 X2 Mobile Technology TL-52 stepping 02
[ 14.311410] SMP alternatives: switching to SMP code
[ 14.311492] Booting processor 1/1 eip 3000
[ 14.321971] Initializing CPU#1
[ 14.401046] Calibrating delay using timer specific routine.. 3214.90 BogoMIPS (lpj=6429816)
[ 14.401054] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f
[ 14.401061] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 14.401064] CPU: L2 Cache: 512K (64 bytes/line)
[ 14.401067] CPU 1(2) -> Core 1
[ 14.401068] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f
[ 14.400988] CPU1: AMD Turion(tm) 64 X2 Mobile Technology TL-52 stepping 02
[ 14.401006] Total of 2 processors activated (6432.84 BogoMIPS).
[ 14.401363] ENABLING IO-APIC IRQs
[ 14.401635] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
[ 14.548770] checking TSC synchronization across 2 CPUs:
[ 0.000002] CPU#0 had -140 usecs TSC skew, fixed it up.
[ 0.000004] CPU#1 had 140 usecs TSC skew, fixed it up.
[ 0.003994] Brought up 2 CPUs
[ 0.036294] migration_cost=233
[ 0.036552] Booting paravirtualized kernel on bare hardware
[ 0.036646] Time: 13:22:55 Date: 06/31/107
[ 0.036677] NET: Registered protocol family 16
[ 0.036758] EISA bus registered
[ 0.036762] ACPI: bus type pci registered
[ 0.037460] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=4
[ 0.037463] PCI: Using configuration type 1
[ 0.037465] Setting up standard PCI resources
[ 0.066940] ACPI: Interpreter enabled
[ 0.066943] ACPI: Using IOAPIC for interrupt routing
[ 0.067236] Error attaching device data
[ 0.067242] Error attaching device data
[ 0.067757] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.067763] PCI: Probing PCI hardware (bus 00)
[ 0.068347] Boot video device is 0000:00:05.0
[ 0.069192] PCI: Transparent bridge - 0000:00:10.0
[ 0.069235] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.093435] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[ 0.099796] ACPI: PCI Interrupt Link [LNKA] (IRQs 16) *0, disabled.
[ 0.100465] ACPI: PCI Interrupt Link [LNKB] (IRQs 17) *0, disabled.
[ 0.101128] ACPI: PCI Interrupt Link [LNKC] (IRQs 16) *0, disabled.
[ 0.101790] ACPI: PCI Interrupt Link [LNKD] (IRQs 17) *0, disabled.
[ 0.102451] ACPI: PCI Interrupt Link [LNEA] (IRQs 18) *0, disabled.
[ 0.103110] ACPI: PCI Interrupt Link [LNEB] (IRQs 19) *11
[ 0.103772] ACPI: PCI Interrupt Link [LNEC] (IRQs 5) *11
[ 0.104436] ACPI: PCI Interrupt Link [LNED] (IRQs 11) *0, disabled.
[ 0.105099] ACPI: PCI Interrupt Link [LUB0] (IRQs 10) *11
[ 0.105759] ACPI: PCI Interrupt Link [LUB2] (IRQs 20) *7
[ 0.106422] ACPI: PCI Interrupt Link [LMAC] (IRQs 21) *5
[ 0.107369] ACPI: PCI Interrupt Link [LAZA] (IRQs 22) *5
[ 0.108036] ACPI: PCI Interrupt Link [LACI] (IRQs 22) *0, disabled.
[ 0.108701] ACPI: PCI Interrupt Link [LMC9] (IRQs 7) *0, disabled.
[ 0.109363] ACPI: PCI Interrupt Link [LSMB] (IRQs 7) *5
[ 0.110022] ACPI: PCI Interrupt Link [LPMU] (IRQs 7) *10
[ 0.110680] ACPI: PCI Interrupt Link [LSA0] (IRQs 23) *10
[ 0.111343] ACPI: PCI Interrupt Link [LSA1] (IRQs 23) *0, disabled.
[ 0.112115] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
[ 0.112304] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.112317] pnp: PnP ACPI init
[ 0.117392] pnp: PnP ACPI: found 13 devices
[ 0.117396] PnPBIOS: Disabled by ACPI PNP
[ 0.117445] PCI: Using ACPI for IRQ routing
[ 0.117448] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.131321] NET: Registered protocol family 8
[ 0.131324] NET: Registered protocol family 20
[ 0.133242] pnp: 00:07: ioport range 0x25c-0x25f has been reserved
[ 0.133542] PCI: Bridge: 0000:00:02.0
[ 0.133544] IO window: disabled.
[ 0.133548] MEM window: fed00000-fedfffff
[ 0.133551] PREFETCH window: disabled.
[ 0.133554] PCI: Bridge: 0000:00:03.0
[ 0.133555] IO window: disabled.
[ 0.133558] MEM window: disabled.
[ 0.133560] PREFETCH window: disabled.
[ 0.133563] PCI: Bridge: 0000:00:04.0
[ 0.133564] IO window: disabled.
[ 0.133567] MEM window: disabled.
[ 0.133569] PREFETCH window: disabled.
[ 0.133572] PCI: Bridge: 0000:00:10.0
[ 0.133573] IO window: disabled.
[ 0.133577] MEM window: disabled.
[ 0.133580] PREFETCH window: disabled.
[ 0.133592] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 0.133599] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 0.133606] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 0.133616] PCI: Setting latency timer of device 0000:00:10.0 to 64
[ 0.133649] NET: Registered protocol family 2
[ 0.188041] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.188198] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.188924] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.189260] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.189263] TCP reno registered
[ 0.208108] checking if image is initramfs... it is
[ 0.895300] Freeing initrd memory: 6788k freed
[ 1.536000] audit: initializing netlink socket (disabled)
[ 1.536000] audit(1185888176.720:1): initialized
[ 1.540000] highmem bounce pool size: 64 pages
[ 1.540000] VFS: Disk quotas dquot_6.5.1
[ 1.540000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.540000] io scheduler noop registered
[ 1.540000] io scheduler anticipatory registered
[ 1.540000] io scheduler deadline registered
[ 1.540000] io scheduler cfq registered (default)
[ 1.556000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 1.556000] assign_interrupt_mode Found MSI capability
[ 1.556000] Allocate Port Service[0000:00:02.0:pcie00]
[ 1.556000] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 1.556000] assign_interrupt_mode Found MSI capability
[ 1.556000] Allocate Port Service[0000:00:03.0:pcie00]
[ 1.556000] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 1.556000] assign_interrupt_mode Found MSI capability
[ 1.556000] Allocate Port Service[0000:00:04.0:pcie00]
[ 1.556000] isapnp: Scanning for PnP cards...
[ 1.908000] isapnp: No Plug & Play device found
[ 1.932000] Real Time Clock Driver v1.12ac
[ 1.932000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.932000] mice: PS/2 mouse device common for all mice
[ 1.936000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 1.936000] input: Macintosh mouse button emulation as /class/input/input0
[ 1.936000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 1.936000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 1.936000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.936000] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 1.936000] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.936000] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.936000] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.936000] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.936000] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.936000] EISA: Probing bus 0 at eisa.0
[ 1.936000] Cannot allocate resource for EISA slot 2
[ 1.936000] EISA: Detected 0 cards.
[ 1.968000] TCP cubic registered
[ 1.968000] NET: Registered protocol family 1
[ 1.968000] Starting balanced_irq
[ 1.968000] Using IPI No-Shortcut mode
[ 1.968000] ACPI: (supports S0 S1 S3 S4 S5)
[ 1.968000] Magic number: 15:536:383
[ 1.968000] Freeing unused kernel memory: 328k freed
[ 1.972000] Time: acpi_pm clocksource has been installed.
[ 1.972000] input: AT Translated Set 2 keyboard as /class/input/input1
[ 3.232000] Capability LSM initialized
[ 3.280000] ACPI: Thermal Zone [TZ00] (60 C)
[ 3.928000] usbcore: registered new interface driver usbfs
[ 3.928000] usbcore: registered new interface driver hub
[ 3.932000] usbcore: registered new device driver usb
[ 3.932000] NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0
[ 3.932000] NFORCE-MCP51: chipset revision 161
[ 3.932000] NFORCE-MCP51: not 100% native mode: will probe irqs later
[ 3.932000] NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller
[ 3.932000] ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio
[ 3.932000] ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
[ 3.932000] Probing IDE interface ide0...
[ 3.944000] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.59.
[ 3.944000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.944000] SCSI subsystem initialized
[ 3.964000] libata version 2.20 loaded.
[ 4.540000] Probing IDE interface ide1...
[ 5.308000] hdc: Optiarc DVD RW AD-5540A, ATAPI CD/DVD-ROM drive
[ 6.004000] ide1 at 0x170-0x177,0x376 on irq 15
[ 6.004000] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 10
[ 6.004000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUB0] -> GSI 10 (level, low) -> IRQ 10
[ 6.004000] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 6.004000] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 6.004000] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
[ 6.004000] ohci_hcd 0000:00:0b.0: irq 10, io mem 0xfecde000
[ 6.060000] usb usb1: configuration #1 chosen from 1 choice
[ 6.060000] hub 1-0:1.0: USB hub found
[ 6.060000] hub 1-0:1.0: 8 ports detected
[ 6.164000] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 21
[ 6.164000] ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LMAC] -> GSI 21 (level, low) -> IRQ 16
[ 6.164000] PCI: Setting latency timer of device 0000:00:14.0 to 64
[ 6.164000] forcedeth: using HIGHDMA
[ 6.468000] usb 1-1: new full speed USB device using ohci_hcd and address 2
[ 6.688000] eth0: forcedeth.c: subsystem: 01631:c024 bound to 0000:00:14.0
[ 6.688000] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 20
[ 6.688000] ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LUB2] -> GSI 20 (level, low) -> IRQ 17
[ 6.688000] PCI: Setting latency timer of device 0000:00:0b.1 to 64
[ 6.688000] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 6.688000] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
[ 6.688000] ehci_hcd 0000:00:0b.1: debug port 1
[ 6.688000] PCI: cache line size of 64 is not supported by device 0000:00:0b.1
[ 6.688000] ehci_hcd 0000:00:0b.1: irq 17, io mem 0xfecdfc00
[ 6.688000] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 6.688000] usb usb2: configuration #1 chosen from 1 choice
[ 6.688000] hub 2-0:1.0: USB hub found
[ 6.688000] hub 2-0:1.0: 8 ports detected
[ 6.700000] usb 1-1: configuration #2 chosen from 2 choices
[ 6.700000] usb 1-1: can't set config #2, error -62
[ 6.792000] sata_nv 0000:00:0e.0: version 3.3
[ 6.792000] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
[ 6.792000] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LSA0] -> GSI 23 (level, low) -> IRQ 18
[ 6.792000] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 6.792000] ata1: SATA max UDMA/133 cmd 0x0001e800 ctl 0x0001e482 bmdma 0x0001e000 irq 18
[ 6.792000] ata2: SATA max UDMA/133 cmd 0x0001e400 ctl 0x0001e082 bmdma 0x0001e008 irq 18
[ 6.792000] scsi0 : sata_nv
[ 6.828000] usb 1-1: USB disconnect, address 2
[ 7.268000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 7.276000] ata1.00: ata_hpa_resize 1: sectors = 234441648, hpa_sectors = 234441648
[ 7.276000] ata1.00: ATA-7: ST9120822AS, 3.ALC, max UDMA/133
[ 7.276000] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 7.284000] ata1.00: ata_hpa_resize 1: sectors = 234441648, hpa_sectors = 234441648
[ 7.284000] ata1.00: configured for UDMA/133
[ 7.284000] scsi1 : sata_nv
[ 7.392000] usb 2-7: new high speed USB device using ehci_hcd and address 3
[ 7.600000] ata2: SATA link down (SStatus 0 SControl 300)
[ 7.608000] ATA: abnormal status 0x7F on port 0x0001e407
[ 7.608000] scsi 0:0:0:0: Direct-Access ATA ST9120822AS 3.AL PQ: 0 ANSI: 5
[ 7.616000] usb 2-7: configuration #1 chosen from 1 choice
[ 7.624000] hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 7.624000] Uniform CD-ROM driver Revision: 3.20
[ 7.636000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[ 7.636000] sda: Write Protect is off
[ 7.636000] sda: Mode Sense: 00 3a 00 00
[ 7.636000] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.636000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[ 7.636000] sda: Write Protect is off
[ 7.636000] sda: Mode Sense: 00 3a 00 00
[ 7.636000] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.636000] sda: sda1 sda2 < sda5 sda6 > sda3
[ 7.820000] sd 0:0:0:0: Attached scsi disk sda
[ 7.824000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 7.928000] usb 1-1: new full speed USB device using ohci_hcd and address 3
[ 8.040000] Attempting manual resume
[ 8.040000] swsusp: Resume From Partition 8:6
[ 8.040000] PM: Checking swsusp image.
[ 8.040000] PM: Resume from disk failed.
[ 8.056000] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 8.056000] EXT3-fs: write access will be enabled during recovery.
[ 8.152000] usb 1-1: configuration #2 chosen from 2 choices
[ 13.908000] kjournald starting. Commit interval 5 seconds
[ 13.908000] EXT3-fs: recovery complete.
[ 13.908000] EXT3-fs: mounted filesystem with ordered data mode.
[ 24.148000] eth0: no link during initialization.
[ 25.368000] i2c_adapter i2c-0: nForce2 SMBus adapter at 0x600
[ 25.368000] i2c_adapter i2c-1: nForce2 SMBus adapter at 0x700
[ 25.380000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 25.384000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 25.456000] NET: Registered protocol family 17
[ 25.772000] Linux agpgart interface v0.102 (c) Dave Jones
[ 25.844000] ath_hal: module license 'Proprietary' taints kernel.
[ 25.844000] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[ 26.020000] wlan: 0.8.4.2 (0.9.3.1)
[ 26.048000] input: PC Speaker as /class/input/input2
[ 26.324000] ath_pci: 0.9.4.5 (0.9.3.1)
[ 26.328000] ACPI: PCI Interrupt Link [LNEC] enabled at IRQ 5
[ 26.328000] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNEC] -> GSI 5 (level, low) -> IRQ 5
[ 26.328000] PCI: Setting latency timer of device 0000:00:05.0 to 64
[ 26.328000] NVRM: loading NVIDIA UNIX x86 Kernel Module 1.0-9755 Mon Feb 26 23:21:15 PST 2007
[ 26.328000] ACPI: PCI Interrupt Link [LNEB] enabled at IRQ 19
[ 26.328000] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNEB] -> GSI 19 (level, low) -> IRQ 19
[ 26.328000] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 26.884000] ath_rate_sample: 1.2 (0.9.3.1)
[ 26.884000] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[ 26.884000] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 26.884000] wifi0: H/W encryption support: WEP AES AES_CCM TKIP
[ 26.884000] wifi0: mac 10.0 phy 6.1 radio 10.2
[ 26.884000] wifi0: Use hw queue 1 for WME_AC_BE traffic
[ 26.884000] wifi0: Use hw queue 0 for WME_AC_BK traffic
[ 26.884000] wifi0: Use hw queue 2 for WME_AC_VI traffic
[ 26.884000] wifi0: Use hw queue 3 for WME_AC_VO traffic
[ 26.884000] wifi0: Use hw queue 8 for CAB traffic
[ 26.884000] wifi0: Use hw queue 9 for beacons
[ 26.896000] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x3aa0b4, caps: 0xa04713/0x200000
[ 26.936000] wifi0: Atheros 5424/2424: mem=0xfedf0000, irq=19
[ 26.940000] input: SynPS/2 Synaptics TouchPad as /class/input/input3
[ 26.992000] eth1: register 'cdc_ether' at usb-0000:00:0b.0-1, CDC Ethernet Device, 00:e1:a7:76:76:81
[ 26.992000] usbcore: registered new interface driver cdc_ether
[ 27.072000] eth1: CDC: unexpected notification 01!
[ 27.076000] eth1: CDC: unexpected notification 01!
[ 27.164000] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 22
[ 27.164000] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LAZA] -> GSI 22 (level, low) -> IRQ 20
[ 27.164000] PCI: Setting latency timer of device 0000:00:10.1 to 64
[ 27.416000] hda_codec: Unknown model for ALC660VD/ALC861VD, trying auto-probe from BIOS...
[ 27.708000] fuse init (API version 7.8)
[ 27.784000] lp: driver loaded but no devices found
[ 27.860000] Adding 2297224k swap on /dev/disk/by-uuid/de6b3a55-c30b-4228-b6fa-5e6df3789737. Priority:-1 extents:1 across:2297224k
[ 28.008000] EXT3 FS on sda3, internal journal
[ 30.428000] NET: Registered protocol family 10
[ 30.428000] lo: Disabled Privacy Extensions
[ 30.428000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 31.084000] input: Power Button (FF) as /class/input/input4
[ 31.084000] ACPI: Power Button (FF) [PWRF]
[ 31.084000] input: Sleep Button (CM) as /class/input/input5
[ 31.084000] ACPI: Sleep Button (CM) [SLPB]
[ 31.084000] input: Lid Switch as /class/input/input6
[ 31.084000] ACPI: Lid Switch [LID]
[ 31.084000] input: Power Button (CM) as /class/input/input7
[ 31.084000] ACPI: Power Button (CM) [PWRB]
[ 31.116000] ACPI: Battery Slot [BAT0] (battery absent)
[ 31.196000] ibm_acpi: ec object not found
[ 31.276000] Using specific hotkey driver
[ 31.400000] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 31.424000] No dock devices found.
[ 31.444000] Asus Laptop ACPI Extras version 0.30
[ 31.444000] Error calling BSTS
[ 31.444000] unsupported model T12M, trying default values
[ 31.444000] send /proc/acpi/dsdt to the developers
[ 31.488000] ACPI: AC Adapter [AC0] (on-line)
[ 31.588000] pcc_acpi: loading...
[ 31.864000] powernow-k8: Found 2 AMD Turion(tm) 64 X2 Mobile Technology TL-52 processors (version 2.00.00)
[ 31.864000] powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x12
[ 31.864000] powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x1e
[ 31.864000] powernow-k8: ph2 null fid transition 0x8
[ 36.300000] ppdev: user-space parallel port driver
[ 38.920000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 38.920000] apm: disabled - APM is not SMP safe.
[ 39.112000] Bluetooth: Core ver 2.11
[ 39.112000] NET: Registered protocol family 31
[ 39.112000] Bluetooth: HCI device and connection manager initialized
[ 39.112000] Bluetooth: HCI socket layer initialized
[ 39.144000] Bluetooth: L2CAP ver 2.8
[ 39.144000] Bluetooth: L2CAP socket layer initialized
[ 39.188000] Bluetooth: RFCOMM socket layer initialized
[ 39.188000] Bluetooth: RFCOMM TTY layer initialized
[ 39.188000] Bluetooth: RFCOMM ver 1.8
[ 52.868000] eth1: no IPv6 routers present
[ 1460.328000] usb 1-1: USB disconnect, address 3
[ 1460.336000] eth1: unregister 'cdc_ether' usb-0000:00:0b.0-1, CDC Ethernet Device
[ 1495.060000] usb 1-2: new full speed USB device using ohci_hcd and address 4
[ 1495.288000] usb 1-2: configuration #2 chosen from 2 choices
[ 1495.296000] eth1: register 'cdc_ether' at usb-0000:00:0b.0-2, CDC Ethernet Device, 00:e1:a7:76:76:81
[ 1495.484000] eth1: CDC: unexpected notification 01!
[ 1495.488000] eth1: CDC: unexpected notification 01!
[ 1537.956000] eth1: no IPv6 routers present
Bus 002 Device 003: ID 174f:a821
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 004: ID 0451:6060 Texas Instruments, Inc.
Bus 001 Device 001: ID 0000:0000
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2)
00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2)
00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2)
00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2)
00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2)
00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2)
00:02.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1)
00:03.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1)
00:04.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1)
00:05.0 VGA compatible controller: nVidia Corporation C51 PCI Express Bridge (rev a2)
00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2)
00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a3)
00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a3)
00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3)
00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3)
00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1)
00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1)
00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2)
00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2)
00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a3)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 Ethernet controller: Atheros Communications, Inc. Unknown device 001c (rev 01)
00:00.0 0500: 10de:02f3 (rev a2)
00:00.1 0500: 10de:02fa (rev a2)
00:00.2 0500: 10de:02fe (rev a2)
00:00.3 0500: 10de:02f8 (rev a2)
00:00.4 0500: 10de:02f9 (rev a2)
00:00.5 0500: 10de:02ff (rev a2)
00:00.6 0500: 10de:027f (rev a2)
00:00.7 0500: 10de:027e (rev a2)
00:02.0 0604: 10de:02fc (rev a1)
00:03.0 0604: 10de:02fd (rev a1)
00:04.0 0604: 10de:02fb (rev a1)
00:05.0 0300: 10de:0247 (rev a2)
00:09.0 0500: 10de:0270 (rev a2)
00:0a.0 0601: 10de:0260 (rev a3)
00:0a.1 0c05: 10de:0264 (rev a3)
00:0b.0 0c03: 10de:026d (rev a3)
00:0b.1 0c03: 10de:026e (rev a3)
00:0d.0 0101: 10de:0265 (rev a1)
00:0e.0 0101: 10de:0266 (rev a1)
00:10.0 0604: 10de:026f (rev a2)
00:10.1 0403: 10de:026c (rev a2)
00:14.0 0680: 10de:0269 (rev a3)
00:18.0 0600: 1022:1100
00:18.1 0600: 1022:1101
00:18.2 0600: 1022:1102
00:18.3 0600: 1022:1103
01:00.0 0200: 168c:001c (rev 01)
ilsensine
31-07-2007, 13:37
snd_hda_intel 21912 1
Infatti; ecco la tua Realtek. E' solo una questione di volume e abilitazione dell'uscita, gioca un pò col mixer.
Ora vediamo per la webcam. Hai due dispositivi usb:
Bus 002 Device 003: ID 174f:a821
Bus 001 Device 004: ID 0451:6060 Texas Instruments, Inc.
Puoi eseguire lsusb con e senza la webcam attaccata, così vediamo chi è?
(sospetto sia la prima; la seconda è forse una scheda wifi?)
ilsensine
01-08-2007, 08:42
ora manka solo l hd audio :(
Guarda, da quello che vedo dovrebbe funzionare.
Se non funzionasse, kde ti avvertirebbe all'avvio.
In alcune situazioni occorre imprecare parecchio con i mixer per riuscire ad abilitare l'audio, per motivi sconosciuti.
Mi spieghi da dove è saltato fuori il nome "realtek"? La scheda dovrebbe essere nvidia, semplice clone di Intel...
Guarda, da quello che vedo dovrebbe funzionare.
Se non funzionasse, kde ti avvertirebbe all'avvio.
In alcune situazioni occorre imprecare parecchio con i mixer per riuscire ad abilitare l'audio, per motivi sconosciuti.
Mi spieghi da dove è saltato fuori il nome "realtek"? La scheda dovrebbe essere nvidia, semplice clone di Intel...
ok esce HDA nvidia (alsa mixer) ma nn s sente nnt ;( :muro:
ilsensine
01-08-2007, 16:11
Urca, hai installato un driver dai sorgenti, e ti stai perdendo col mixer :asd:
A parte gli scherzi, non so che dirti. Mi sono capitati portatili così "rognosi", ma in un modo o nell'altro - rivoltando il mixer, le combinazioni dei tasti per il volume, tutto ciò che avevo sottomano) sono riuscito a farli andare.
ilsensine
14-09-2007, 12:27
Piccolo aggiornamento per te...
mi è capitato un computer con lo stesso tuo problema, per quando smanettavo con il mixer l'audio non ne voleva sapere di uscire. Spulciando nelle patch relative al driver intel_hda, ho visto che nel tempo hanno portato correzioni a problemi di funzionamento relativi a certe schede madri. Nel mio caso è bastato installare un kernel recente per risolvere il problema, forse è necessario anche nel tuo.
Piccolo aggiornamento per te...
mi è capitato un computer con lo stesso tuo problema, per quando smanettavo con il mixer l'audio non ne voleva sapere di uscire. Spulciando nelle patch relative al driver intel_hda, ho visto che nel tempo hanno portato correzioni a problemi di funzionamento relativi a certe schede madri. Nel mio caso è bastato installare un kernel recente per risolvere il problema, forse è necessario anche nel tuo.
°-°
dopo quella volta ho abbandonato il mondo di linux e sono rientrato nel mondo di winzoz :eek:
quindi sekondo te se installo una versione di ubuntu + recente l audio dovrebbe funzionareW? :D
vBulletin® v3.6.4, Copyright ©2000-2025, Jelsoft Enterprises Ltd.