seky
27-06-2007, 20:36
Buon dì a tutti allora ho un piccolo problemino vorrei cambiare la mia vecchia scheda video una matrox g400 ma non sò che scheda comprare premetto che non vorrei spendere più di 80 euro e dovrebbe avere 250Mb di memoria se possibile, il problema è che la mia scheda madre è un pò vecchiotta infatti ha uno slot Agp ed inoltre so che da problemi d'incompatibilità con alcune schede video la configurazione del mio pc è la seguente processore Amd Athlon 1,24 Ghz un Giga di Ram la scheda madre è una
Ecs K7S5A PRO spero che qualcuno possa gentilmente darmi una mano nel darmi un consiglio grazie in anticipo a dimenticavo lo slot Agp ha un alimentazione a 1,5 v di sotto riporto le caratteristiche della scheda madre
Processor
• Supports AMD Athlon XP/Athlon/Duron processors
• Supports 266 MHz Front-Side Bus
Note: Processors are automatically configured using firmware and a synchronous Host/DRAM Clock Scheme.
Memory
• Two 168-pin DIMM slots for SDRAM memory modules
• Two 184-pin DIMM slots for DDR memory modules
• Support SDRAM up to 133 MHz and DDR up to 266 MHz memory bus
• Maximum installed memory is 1GB
Note: You cannot use SDRAM and DDR simultane-ously.
Expansion Slots
• One AMR slot for a special audio/modem riser card
• One AGP slot for AGP 2.0-compliant interface (supports 1.5V AGP card only)
• Five 32-bit PCI slots for PCI 2.2-compliant bus interface
Note: The PCI1 slot does not concurrently work with USB 2.0 controller (VT6202). Therefore, you must disable the USB 2.0 controller through BIOS setup before using the PCI1 slot.
Onboard IDE channels
• Primary and Secondary PCI IDE channels
• Support for PIO (programmable input/output) modes
• Support for Multiword DMA modes
• Support for Bus Mastering and Ultra DMA 33/66/100 modes
Power Supply and Power Management
• ATX power supply connector
• Meets ACPI 1.0b and APM 1.2 requirements, keyboard power on/off
• Supports RTC Alarm, Wake On Modem, AC97 Wake-Up and USB Wake-Up
Audio
• Compliant with AC’97 2.2 specification
• Full-duplex Codec with independent and variable sam-pling rate
• Earphone Buffer Built-In, SNR up to 90db
• 2Ch DAC, support 2-channel speak-out
• Advanced power management support
Built-in Ethernet LAN (optional)
• Built-in 10BaseT/100BaseTX Ethernet LAN
• LAN controller integrates Fast Ethernet MAC and PHY compliant with IEEE802.3u 100BASE-TX, 10BASE-T and ANSI X3.263 TP-PMD standards
• Compliant with ACPI 1.0 and the Network Device Class Power Management 1.0
• High Performance provided by 100Mbps clock generator and data recovery circuit for 100Mbps receiver
Onboard I/O Ports
• Two PS/2 ports for mouse and keyboard
• One serial port
• One parallel port
• Ten USB ports (four back-panel USB2.0 ports, onboard USB headers providing six extra USB1.1 ports)
• Audio jacks for microphone, line-in and line-out
Hardware Moni-toring
Built-in hardware monitoring for CPU & System temperatures, fan speeds and mainboard voltages.
Onboard Flash ROM
Supports Plug and Play configuration of peripheral devices and expansion cards.
AGP Slot
The AGP slot is used to install a graphics adapter that supports the 4xAGP specifications and has a 4xAGP edge connector.
Note: The above layout is for reference only. The AGP slot may be different from your mainboard. Please refer to actual shipment
Ecs K7S5A PRO spero che qualcuno possa gentilmente darmi una mano nel darmi un consiglio grazie in anticipo a dimenticavo lo slot Agp ha un alimentazione a 1,5 v di sotto riporto le caratteristiche della scheda madre
Processor
• Supports AMD Athlon XP/Athlon/Duron processors
• Supports 266 MHz Front-Side Bus
Note: Processors are automatically configured using firmware and a synchronous Host/DRAM Clock Scheme.
Memory
• Two 168-pin DIMM slots for SDRAM memory modules
• Two 184-pin DIMM slots for DDR memory modules
• Support SDRAM up to 133 MHz and DDR up to 266 MHz memory bus
• Maximum installed memory is 1GB
Note: You cannot use SDRAM and DDR simultane-ously.
Expansion Slots
• One AMR slot for a special audio/modem riser card
• One AGP slot for AGP 2.0-compliant interface (supports 1.5V AGP card only)
• Five 32-bit PCI slots for PCI 2.2-compliant bus interface
Note: The PCI1 slot does not concurrently work with USB 2.0 controller (VT6202). Therefore, you must disable the USB 2.0 controller through BIOS setup before using the PCI1 slot.
Onboard IDE channels
• Primary and Secondary PCI IDE channels
• Support for PIO (programmable input/output) modes
• Support for Multiword DMA modes
• Support for Bus Mastering and Ultra DMA 33/66/100 modes
Power Supply and Power Management
• ATX power supply connector
• Meets ACPI 1.0b and APM 1.2 requirements, keyboard power on/off
• Supports RTC Alarm, Wake On Modem, AC97 Wake-Up and USB Wake-Up
Audio
• Compliant with AC’97 2.2 specification
• Full-duplex Codec with independent and variable sam-pling rate
• Earphone Buffer Built-In, SNR up to 90db
• 2Ch DAC, support 2-channel speak-out
• Advanced power management support
Built-in Ethernet LAN (optional)
• Built-in 10BaseT/100BaseTX Ethernet LAN
• LAN controller integrates Fast Ethernet MAC and PHY compliant with IEEE802.3u 100BASE-TX, 10BASE-T and ANSI X3.263 TP-PMD standards
• Compliant with ACPI 1.0 and the Network Device Class Power Management 1.0
• High Performance provided by 100Mbps clock generator and data recovery circuit for 100Mbps receiver
Onboard I/O Ports
• Two PS/2 ports for mouse and keyboard
• One serial port
• One parallel port
• Ten USB ports (four back-panel USB2.0 ports, onboard USB headers providing six extra USB1.1 ports)
• Audio jacks for microphone, line-in and line-out
Hardware Moni-toring
Built-in hardware monitoring for CPU & System temperatures, fan speeds and mainboard voltages.
Onboard Flash ROM
Supports Plug and Play configuration of peripheral devices and expansion cards.
AGP Slot
The AGP slot is used to install a graphics adapter that supports the 4xAGP specifications and has a 4xAGP edge connector.
Note: The above layout is for reference only. The AGP slot may be different from your mainboard. Please refer to actual shipment