seky
27-06-2007, 21:23
Ciao ho un problemino dovrei cambiare la mia vecchia scheda video una matrox g400 il mio problema θ che la scheda madre θ vecchiotta θ una
K7S5A PRO ed ha lo slot AGP il processore θ un Amd 1,24 GHz un Giga di Ram
le caratteristiche della scheda madre sono le seguenti:
Processor
Supports AMD Athlon XP/Athlon/Duron processors
Supports 266 MHz Front-Side Bus
Note: Processors are automatically configured using firmware and a synchronous Host/DRAM Clock Scheme.
Memory
Two 168-pin DIMM slots for SDRAM memory modules
Two 184-pin DIMM slots for DDR memory modules
Support SDRAM up to 133 MHz and DDR up to 266 MHz memory bus
Maximum installed memory is 1GB
Note: You cannot use SDRAM and DDR simultane-ously.
Expansion Slots
One AMR slot for a special audio/modem riser card
One AGP slot for AGP 2.0-compliant interface (supports 1.5V AGP card only)
Five 32-bit PCI slots for PCI 2.2-compliant bus interface
Note: The PCI1 slot does not concurrently work with USB 2.0 controller (VT6202). Therefore, you must disable the USB 2.0 controller through BIOS setup before using the PCI1 slot.
Onboard IDE channels
Primary and Secondary PCI IDE channels
Support for PIO (programmable input/output) modes
Support for Multiword DMA modes
Support for Bus Mastering and Ultra DMA 33/66/100 modes
Power Supply and Power Management
ATX power supply connector
Meets ACPI 1.0b and APM 1.2 requirements, keyboard power on/off
Supports RTC Alarm, Wake On Modem, AC97 Wake-Up and USB Wake-Up
Audio
Compliant with AC97 2.2 specification
Full-duplex Codec with independent and variable sam-pling rate
Earphone Buffer Built-In, SNR up to 90db
2Ch DAC, support 2-channel speak-out
Advanced power management support
Built-in Ethernet LAN (optional)
Built-in 10BaseT/100BaseTX Ethernet LAN
LAN controller integrates Fast Ethernet MAC and PHY compliant with IEEE802.3u 100BASE-TX, 10BASE-T and ANSI X3.263 TP-PMD standards
Compliant with ACPI 1.0 and the Network Device Class Power Management 1.0
High Performance provided by 100Mbps clock generator and data recovery circuit for 100Mbps receiver
Ports
Two PS/2 ports for mouse and keyboard
One serial port
One parallel port
Ten USB ports (four back-panel USB2.0 ports, onboard USB headers providing six extra USB1.1 ports)
Audio jacks for microphone, line-in and line-out
Hardware Moni-toring
Built-in hardware monitoring for CPU & System temperatures, fan speeds and mainboard voltages.
Onboard Flash ROM
Supports Plug and Play configuration of peripheral devices and expansion cards.
AGP Slot
The AGP slot is used to install a graphics adapter that supports the 4xAGP specifications and has a 4xAGP edge connector.
Note: The above layout is for reference only. The AGP slot may be different from your mainboard. Please refer to actual shipment.
Il mio problema e che non so quale scheda video prendere in quanto ho saputo che alcune schede hanno problemi d'incompatibilitΰ con la mia scheda madre
K7S5A PRO ed ha lo slot AGP il processore θ un Amd 1,24 GHz un Giga di Ram
le caratteristiche della scheda madre sono le seguenti:
Processor
Supports AMD Athlon XP/Athlon/Duron processors
Supports 266 MHz Front-Side Bus
Note: Processors are automatically configured using firmware and a synchronous Host/DRAM Clock Scheme.
Memory
Two 168-pin DIMM slots for SDRAM memory modules
Two 184-pin DIMM slots for DDR memory modules
Support SDRAM up to 133 MHz and DDR up to 266 MHz memory bus
Maximum installed memory is 1GB
Note: You cannot use SDRAM and DDR simultane-ously.
Expansion Slots
One AMR slot for a special audio/modem riser card
One AGP slot for AGP 2.0-compliant interface (supports 1.5V AGP card only)
Five 32-bit PCI slots for PCI 2.2-compliant bus interface
Note: The PCI1 slot does not concurrently work with USB 2.0 controller (VT6202). Therefore, you must disable the USB 2.0 controller through BIOS setup before using the PCI1 slot.
Onboard IDE channels
Primary and Secondary PCI IDE channels
Support for PIO (programmable input/output) modes
Support for Multiword DMA modes
Support for Bus Mastering and Ultra DMA 33/66/100 modes
Power Supply and Power Management
ATX power supply connector
Meets ACPI 1.0b and APM 1.2 requirements, keyboard power on/off
Supports RTC Alarm, Wake On Modem, AC97 Wake-Up and USB Wake-Up
Audio
Compliant with AC97 2.2 specification
Full-duplex Codec with independent and variable sam-pling rate
Earphone Buffer Built-In, SNR up to 90db
2Ch DAC, support 2-channel speak-out
Advanced power management support
Built-in Ethernet LAN (optional)
Built-in 10BaseT/100BaseTX Ethernet LAN
LAN controller integrates Fast Ethernet MAC and PHY compliant with IEEE802.3u 100BASE-TX, 10BASE-T and ANSI X3.263 TP-PMD standards
Compliant with ACPI 1.0 and the Network Device Class Power Management 1.0
High Performance provided by 100Mbps clock generator and data recovery circuit for 100Mbps receiver
Ports
Two PS/2 ports for mouse and keyboard
One serial port
One parallel port
Ten USB ports (four back-panel USB2.0 ports, onboard USB headers providing six extra USB1.1 ports)
Audio jacks for microphone, line-in and line-out
Hardware Moni-toring
Built-in hardware monitoring for CPU & System temperatures, fan speeds and mainboard voltages.
Onboard Flash ROM
Supports Plug and Play configuration of peripheral devices and expansion cards.
AGP Slot
The AGP slot is used to install a graphics adapter that supports the 4xAGP specifications and has a 4xAGP edge connector.
Note: The above layout is for reference only. The AGP slot may be different from your mainboard. Please refer to actual shipment.
Il mio problema e che non so quale scheda video prendere in quanto ho saputo che alcune schede hanno problemi d'incompatibilitΰ con la mia scheda madre