sb 16 su 486.. nn mi funzia sul dos!

[Marc Wolmots]

ciao raga ho un problemino..

ho un 486 e una soundblaster 16 isa. in ambiente win95 funziona ma in ambito dos no. nn ho + i driver.. ci sono ancora su internet? e x far partire la sb16 da dos devo toccare l'autoexec?

grazie!






altro che intel core 2.. 486 sx 25mhz..:asd:

[imayoda]

Ahhhhhh.. che ricordi (sfuocati). Allora: internet lascialo stare che non esisteva al tempo :asd: al massimo toverai una guida..
Da quello che ricordo io serve una bella modifica al autoexec.bat e al config.sys :confused: saranno 15 anni che non metto mano..
DACCI DENTRO!!! :)

[Marc Wolmots]

nn so assolutamente cosa mettere nell'autoexec e nel config!

qualcuno può aiutarmi??

[imayoda]

:) Io nn ricordo una cippa sorry.. spera nella migliore memoria di altri

[simone123]

c'erano alcune stringhe da modificare, purtoppo nn le ricordo... sono passati anni...
bei tempi quelli in cui bisognava modificare le config da dos... audio, e memoria estesa su tutte...
se riesco a fare mente locale o a trovare qlk info ti posto ;)

[Squalo71]

ciao raga ho un problemino..

ho un 486 e una soundblaster 16 isa. in ambiente win95 funziona ma in ambito dos no. nn ho + i driver.. ci sono ancora su internet? e x far partire la sb16 da dos devo toccare l'autoexec?

grazie!

altro che intel core 2.. 486 sx 25mhz..:asd:
Allora, non ricordo benissimo, comunque era nell'autoexec qualcosa del tipo:
set blaster a=220 I=5 d=...
Purtroppo non so essere più preciso, ma appena trovo qualcosa te lo faccio sapere ;)

HO VINTO QUACCHECCOSA?!?!?

[Squalo71]

SET BLASTER=A220 I5 D1 T3 P330 H6 E620
| | | | | | | | |
| | | | | | | | |_______ AWE 32 Only Parameter
| | | | | | | |__________ "High" DMA Channel
| | | | | | |_______________ MIDI Port
| | | | | |__________________ Type of Card
| | | | |_____________________ DMA Channel
| | | |________________________ Interrupt
| | |_____________________________ Port Address
| |___________________________________ Environment Variable
|________________________________________ DOS Command

NOTE: There can be no spaces between the word BLASTER and the equal sign (=).
If you have a space in there, your system will read the parameter incorrectly,
and it will not be recognized by our games.

(Some of these parameters (P, H, and E) are dependant on certain types of
cards. For example, the E is only needed if you have an AWE 32. The
minimum requirements are to have the A, I, D, & T parameters. The other
three may or may not be needed depending on what type of card you have.
Please read this entire section to see if you need any of them. If you
are using a clone card, or some card that's not a "true" Soundblaster,
then you will most likely only need A, I, D, and T.)

Now, these may not (most likely not) be the same for your board, because the
Port Address, Interrupt and DMA Channel can be set by adjusting "jumpers" on
your sound board. Some newer cards have this information controlled by
software, please consult your card's manual for more information on how to set
these things. You should also check your manual if you are unclear as to how
to tell what settings your card is set at. The information *IS* important, so
it's recommended that you know precisely what the settings are. If you are
using a card that "emulates" the Soundblaster (such as the Gravis UltraSound
through software, or the PAS16), you should check your card's manual on how to
set the card for Soundblaster emulation.

For PORT ADDRESS, it's almost always 220. That seems to be the default for
most sound cards out there, and unless you know you've switched it away from
220, it's a safe bet it's still there.

The INTERRUPT is something that varies from system to system. Mystic Towers
and games prior to Raptor require that your IRQ be set at 7 or less. Apogee
does not recommend using IRQ2, as it causes problems.

The DMA CHANNEL sometimes causes problems if it isn't set to 1, which is the
usual default. If it is not set correctly, some Apogee games may lock up
when the sound is turned on.

The TYPE OF CARD should be 1 if you have an older Soundblaster, or a Sound
Blaster emulating card. Use 3 if you have a newer plain Soundblaster. Use
2 for an older Soundblaster Pro. Use 4 for a newer Soundblaster Pro.

The MIDI PORT parameter will only be needed if you are using a card that has
MIDI capabilites. If so, this is where you define what MIDI port you are
using. 330 seems to be the default, so if you have a MIDI card, and you
haven't changed anything from factory defaults, this is probably where it still
is.

The HIGH DMA CHANNEL is something that is used primarily on Soundblaster 16
cards. This is not the same as the standard DMA channel, this is a different
one. This is only used if you're using a 16 bit sound card capable of playing
16 bit Soundblaster sounds. By default, this is usually 5, so unless you know
that it's something else, it's probably still 5.

The E620 parameter is something that is needed _only_ if you have a Creative
Labs AWE 32 sound card. If you have one of these, this parameter will have
been set up properly assuming you've installed the software that came with the
card. Check your AWE 32 documentation for a more thorough explanation of what
this parameter is used for.

[imayoda]

Mi commuovo a vedere ciò che era la mia vita 10 anni fa e più...:cry: :cry: :cry:

[Marc Wolmots]

grazie x le risp!

allora se la mia è una vecchia soundblaster 16 isa è:

SET BLASTER=A220 I5 D1 T1 (P330 H5)

in parentesi quello che potrei mettere ma nn è obbligatorio..

[Squalo71]

grazie x le risp!

allora se la mia è una vecchia soundblaster 16 isa è:

SET BLASTER=A220 I5 D1 T1 (P330 H5)

in parentesi quello che potrei mettere ma nn è obbligatorio..
Forse va bene anche T3