mrt75
15-11-2006, 21:46
Salve vorrei fare alcune modifiche al mio impianto a liquido,ora ho 1 pompa Hydor seltz l30 dentro la tanica in plexy sempre costruita da me.Vorrei prenderne una nuova e metterla in esterno alla vashetta(un'altra sempre fatta da me ma + piccola),cioe non in immersione.Ho notato la
Laing Pompa 12V Max Flox 1500L/h D5
This pump is used for water cooling of processors and electronic components. Due to its size and output, different ranges of application are available. This pump is an electronically commuted ball-motor pump, with running times of more than 50.000 hours at 12 V. The only flexible part of a ball-motor pump is a sphere-formed rotor-/runner unit, which is propped up against an extremely hard, wear-resistant ceramics bearing ball. A conventional axle with journal bearing and shaft sealing is not available. The spherical bearing of the rotor-/runner unit on the ceramics bearing ball provides a lot of advantages: a development of the bearing play – and thus a noise increase - is theoretically not possible. The pump is silent over the whole running time.
The bearing is self-adjusting. It is lubricated directly by the delivery medium (wet-running pump). There is basically no need for maintenance. Since the rotor is always held magnetically in the intended position, smaller dirt particles are no problem. Blocking of the pump is not possible under normal conditions. Even after lengthy downtimes a safe startup is ensured. The permanent magnetic rotor/ runner unit is propelled by a magnetic field, which is produced by the surrounding stator. This is built entirely around the rotor. The entire pump is thus with 38mm only a little higher than the stator itself. It easily fits into all conventional PC, Barebone and Mini PC cases. A separate magnetic shielding is not necessary under normal conditions. There’s no need for a separate magnetic shielding. The ball motor principle enables an economical enterprise with comparatively high performance. The tension variation can easily regulate the DDC direct current pump over a large capacity range. All medium-affecting parts are completely corrosion resistant.
This pump has a controller and is five-step adjustable with 1.800-4.800 revs./min. Mounting plate is included in delivery!
Specifications:
Dimensions: (WxLxH) 90x90x90mm (without connections)
Motor type: ellectronically commuted ball motor
Rated voltage: 12 V DC direct current
Power input: 23 W
Admissible voltage area: 8 to 24 V
Delivery height: at 12V: 3,7m
max. Flow rate: 1500L/h
Delivery media: water, water-/glycol compounds
Max. System temperature: 60° C
Medium-affecting parts: stainless steel 1.4571, PPS-GF40, EPDM O-ring sealings,
Aluminium oxide, hard carbon
Connections: 2x 1/2" tubing connection
Others: this pump is five-step adjustable
P1 = 1.800 revs./min
P2 = 2.550 revs./min
P3 = 3.300 revs./min
P4 = 4.050 revs./min
P5 = 4.800 revs./min
http://img505.imageshack.us/img505/3267/prod32474662vz7.jpg (http://imageshack.us)
Come vi pare?,c'e' qualcosa di meglio,come rumore,durato,portata ecc ecc ?
Laing Pompa 12V Max Flox 1500L/h D5
This pump is used for water cooling of processors and electronic components. Due to its size and output, different ranges of application are available. This pump is an electronically commuted ball-motor pump, with running times of more than 50.000 hours at 12 V. The only flexible part of a ball-motor pump is a sphere-formed rotor-/runner unit, which is propped up against an extremely hard, wear-resistant ceramics bearing ball. A conventional axle with journal bearing and shaft sealing is not available. The spherical bearing of the rotor-/runner unit on the ceramics bearing ball provides a lot of advantages: a development of the bearing play – and thus a noise increase - is theoretically not possible. The pump is silent over the whole running time.
The bearing is self-adjusting. It is lubricated directly by the delivery medium (wet-running pump). There is basically no need for maintenance. Since the rotor is always held magnetically in the intended position, smaller dirt particles are no problem. Blocking of the pump is not possible under normal conditions. Even after lengthy downtimes a safe startup is ensured. The permanent magnetic rotor/ runner unit is propelled by a magnetic field, which is produced by the surrounding stator. This is built entirely around the rotor. The entire pump is thus with 38mm only a little higher than the stator itself. It easily fits into all conventional PC, Barebone and Mini PC cases. A separate magnetic shielding is not necessary under normal conditions. There’s no need for a separate magnetic shielding. The ball motor principle enables an economical enterprise with comparatively high performance. The tension variation can easily regulate the DDC direct current pump over a large capacity range. All medium-affecting parts are completely corrosion resistant.
This pump has a controller and is five-step adjustable with 1.800-4.800 revs./min. Mounting plate is included in delivery!
Specifications:
Dimensions: (WxLxH) 90x90x90mm (without connections)
Motor type: ellectronically commuted ball motor
Rated voltage: 12 V DC direct current
Power input: 23 W
Admissible voltage area: 8 to 24 V
Delivery height: at 12V: 3,7m
max. Flow rate: 1500L/h
Delivery media: water, water-/glycol compounds
Max. System temperature: 60° C
Medium-affecting parts: stainless steel 1.4571, PPS-GF40, EPDM O-ring sealings,
Aluminium oxide, hard carbon
Connections: 2x 1/2" tubing connection
Others: this pump is five-step adjustable
P1 = 1.800 revs./min
P2 = 2.550 revs./min
P3 = 3.300 revs./min
P4 = 4.050 revs./min
P5 = 4.800 revs./min
http://img505.imageshack.us/img505/3267/prod32474662vz7.jpg (http://imageshack.us)
Come vi pare?,c'e' qualcosa di meglio,come rumore,durato,portata ecc ecc ?