Alexl1976
25-08-2006, 13:33
Ciao a tutti, da uqndo ho cambiato la mia vecchia scheda video, Radeon 9600 XT 128 MB con una nuova Cul3D 7600 GS 256 MB, ho dei problemi che per il momento ho riscontrato con 3Dmark 03 e 05.
In particolare nel 3Dmark 03 il pc mi si blocca al test della CPU, ma .......... .
Questa e' la mia attuale configurazione:
Athlon Xp 2.8 su Asus A7n8x -E Deluxe
2 HDD Sata 160 GG in raid 0
1 GB di Ram in Dual Channel
Scheda video AGP Club3D 7600 GS 256 MB
Lettore DVD
Masterizzatore DVD
Case Thermaltake Xaser III con 5 ventole
Alimentatore Thermaltake Purepower 420W, specifiche:
Detail Specifications
P/N W0008R w/
Active PFC (Power Factor Correction) W0009R Fan Dual Fan:
Two Ball Bearing,
Temp. Auto Control
1300 rpm at 25C ~
2400 rpm at 80C
Maximum Power 420 Watts P. G. Signal 100-500ms
Switches ATX Logic on-off additional
power rocker switch Over Voltage Protection recycle AC to reset +5V trip point < +6.8V
+3.3V trip point < +4.5V
+12V trip point <+15.6V
Noise 19dBA
Input Voltage 100 VAC / 240 VAC Input Frequency Range 47-63 Hz
Input Current 8.0A Hold-up Time > 16ms at Full Load
Efficiency > 65% Unit Size 15cm(L)x14cm(W)x8.6cm(H)
Net Weight 2.5kg
Secondo voi ho possibili problemi di alimentazione?
C'e' qualche test da fare per vedere se il problema sta' proprio nella'limentazione?
Ho anche provato a staccare i due lettori ma niente da fare.
Secondo voi che cosa puo' essere?
In particolare nel 3Dmark 03 il pc mi si blocca al test della CPU, ma .......... .
Questa e' la mia attuale configurazione:
Athlon Xp 2.8 su Asus A7n8x -E Deluxe
2 HDD Sata 160 GG in raid 0
1 GB di Ram in Dual Channel
Scheda video AGP Club3D 7600 GS 256 MB
Lettore DVD
Masterizzatore DVD
Case Thermaltake Xaser III con 5 ventole
Alimentatore Thermaltake Purepower 420W, specifiche:
Detail Specifications
P/N W0008R w/
Active PFC (Power Factor Correction) W0009R Fan Dual Fan:
Two Ball Bearing,
Temp. Auto Control
1300 rpm at 25C ~
2400 rpm at 80C
Maximum Power 420 Watts P. G. Signal 100-500ms
Switches ATX Logic on-off additional
power rocker switch Over Voltage Protection recycle AC to reset +5V trip point < +6.8V
+3.3V trip point < +4.5V
+12V trip point <+15.6V
Noise 19dBA
Input Voltage 100 VAC / 240 VAC Input Frequency Range 47-63 Hz
Input Current 8.0A Hold-up Time > 16ms at Full Load
Efficiency > 65% Unit Size 15cm(L)x14cm(W)x8.6cm(H)
Net Weight 2.5kg
Secondo voi ho possibili problemi di alimentazione?
C'e' qualche test da fare per vedere se il problema sta' proprio nella'limentazione?
Ho anche provato a staccare i due lettori ma niente da fare.
Secondo voi che cosa puo' essere?