sneak
30-05-2006, 18:07
salve a tutti.
ho da poco installato un nuovo hd serial ata sul mio pc ed ho dei problemi a farlo vedere al mio linux suse 9.2.
son sicuro che il controller sia configurato e che in fase di boot venga visto ma sembra che manchi il block device relativo.
Ecco l'echo del dmesg: come si vede ho anche un sottosistema scsi....
SCSI subsystem initialized
ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 185
ahc_pci:0:14:0: Host Adapter Bios disabled. Using default SCSI device parameters
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
(scsi0:A:2): 20.000MB/s transfers (20.000MHz, offset 15)
Vendor: PIONEER Model: DVD-ROM DVD-305 Rev: 1.00
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:3): 20.000MB/s transfers (20.000MHz, offset 15)
Vendor: PLEXTOR Model: CD-ROM PX-40TS Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:6): 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
Vendor: QUANTUM Model: ATLAS IV 18 WLS Rev: 0909
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:6:0: Tagged Queuing enabled. Depth 32
SCSI device sda: 35885168 512-byte hdwr sectors (18373 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
Attached scsi disk sda at scsi0, channel 0, id 6, lun 0
libata version 1.02 loaded.
sata_via version 0.20
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 193
sata_via(0000:00:0f.0): routed to hard irq line 5
ata1: SATA max UDMA/133 cmd 0xD000 ctl 0xC802 bmdma 0xB800 irq 193
ata2: SATA max UDMA/133 cmd 0xC400 ctl 0xC002 bmdma 0xB808 irq 193
ata1: dev 0 cfg 49:2f00 82:346b 83:7fe9 84:4773 85:3469 86:3c01 87:4763 88:407f
ata1: dev 0 ATA, max UDMA/133, 321672960 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi1 : sata_via
ata2: no device found (phy stat 00000000)
scsi2 : sata_via
Vendor: ATA Model: HDT722516DLA380 Rev: V43O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 321672960 512-byte hdwr sectors (164697 MB)
SCSI device sdb: drive cache: write back
sdb: unknown partition table
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
ma che sia da creare manualmente il block device con mknod??
se faccio cfdisk /dev/sdb mi dice che non esiste il disco... e se vado in dev effettivamente sdb non c'è!
Cosa devo fare?
ho da poco installato un nuovo hd serial ata sul mio pc ed ho dei problemi a farlo vedere al mio linux suse 9.2.
son sicuro che il controller sia configurato e che in fase di boot venga visto ma sembra che manchi il block device relativo.
Ecco l'echo del dmesg: come si vede ho anche un sottosistema scsi....
SCSI subsystem initialized
ACPI: PCI interrupt 0000:00:0e.0[A] -> GSI 19 (level, low) -> IRQ 185
ahc_pci:0:14:0: Host Adapter Bios disabled. Using default SCSI device parameters
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
(scsi0:A:2): 20.000MB/s transfers (20.000MHz, offset 15)
Vendor: PIONEER Model: DVD-ROM DVD-305 Rev: 1.00
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:3): 20.000MB/s transfers (20.000MHz, offset 15)
Vendor: PLEXTOR Model: CD-ROM PX-40TS Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:6): 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
Vendor: QUANTUM Model: ATLAS IV 18 WLS Rev: 0909
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:6:0: Tagged Queuing enabled. Depth 32
SCSI device sda: 35885168 512-byte hdwr sectors (18373 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
Attached scsi disk sda at scsi0, channel 0, id 6, lun 0
libata version 1.02 loaded.
sata_via version 0.20
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 193
sata_via(0000:00:0f.0): routed to hard irq line 5
ata1: SATA max UDMA/133 cmd 0xD000 ctl 0xC802 bmdma 0xB800 irq 193
ata2: SATA max UDMA/133 cmd 0xC400 ctl 0xC002 bmdma 0xB808 irq 193
ata1: dev 0 cfg 49:2f00 82:346b 83:7fe9 84:4773 85:3469 86:3c01 87:4763 88:407f
ata1: dev 0 ATA, max UDMA/133, 321672960 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi1 : sata_via
ata2: no device found (phy stat 00000000)
scsi2 : sata_via
Vendor: ATA Model: HDT722516DLA380 Rev: V43O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 321672960 512-byte hdwr sectors (164697 MB)
SCSI device sdb: drive cache: write back
sdb: unknown partition table
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
ma che sia da creare manualmente il block device con mknod??
se faccio cfdisk /dev/sdb mi dice che non esiste il disco... e se vado in dev effettivamente sdb non c'è!
Cosa devo fare?