peppeunz
20-04-2006, 16:48
Salve.
Ho un router 802.11b/g della Sweex, marca che il mio negazio di fiducia tratta da anni, dovrebbe avere un chip Conexant Hasbani.
L'interfaccia web pero' e' davvero penosa (lo so quando si risparmia c'e' sempre un perche'...) e volevo che mi aiutaste a capire un attimo come settare certi valori:
per quanto riguarda il filtraggio degli indirizzi MAC, per motivi di sicurezza vorrei abilitare solo i due indirizzi mac dei miei due pc.
http://web.tiscali.it/peppeunz/3-3-10.jpg
e il manuale dice:
Source MAC: When the bridge filtering is enabled, enter the Source MAC address, select Block and click Add. Then all incoming WAN and LAN Ethernet packets matched with this source MAC address will be filtered out. If the Forward is selected, then the packets will be forwarded to the destination PC.
Destination MAC: When the bridge filtering is enabled, enter the Destination MAC address, select Block and click Add. Then all incoming WAN and LAN Ethernet packets matched with this destination MAC address will be filtered out. If the Forward is selected, then the packets will be forwarded to the destination PC.
Type: Enter the hexadecimal number for the Ethernet type field in Ethernet_II packets. For example, 0800 is for IP protocol.
Ho provato a mettere il mac del mio pc sia in source che in destination e type 0800 ma poi non riesco ne a connettermi a internet ne al router stesso.
Allora cosa ci devo mettere in questi campi?
Secondo punto:
http://web.tiscali.it/peppeunz/3-3-11a.jpg
e il manuale dice:
Basic Rate : Select the basic rates based on the speed of wireless adapters on the WLAN (wireless local area network).
Support/TX Rate : Select the transfer rates based on the speed of wireless adapters on the WLAN (wireless local area network).
Mi conviene spuntare tutte le velocita' supportate?
E per la sezione "Dynamic Antenna Switching", di cui il manuale non parla, mi conviene tenerla su enable?
Grazie
Ho un router 802.11b/g della Sweex, marca che il mio negazio di fiducia tratta da anni, dovrebbe avere un chip Conexant Hasbani.
L'interfaccia web pero' e' davvero penosa (lo so quando si risparmia c'e' sempre un perche'...) e volevo che mi aiutaste a capire un attimo come settare certi valori:
per quanto riguarda il filtraggio degli indirizzi MAC, per motivi di sicurezza vorrei abilitare solo i due indirizzi mac dei miei due pc.
http://web.tiscali.it/peppeunz/3-3-10.jpg
e il manuale dice:
Source MAC: When the bridge filtering is enabled, enter the Source MAC address, select Block and click Add. Then all incoming WAN and LAN Ethernet packets matched with this source MAC address will be filtered out. If the Forward is selected, then the packets will be forwarded to the destination PC.
Destination MAC: When the bridge filtering is enabled, enter the Destination MAC address, select Block and click Add. Then all incoming WAN and LAN Ethernet packets matched with this destination MAC address will be filtered out. If the Forward is selected, then the packets will be forwarded to the destination PC.
Type: Enter the hexadecimal number for the Ethernet type field in Ethernet_II packets. For example, 0800 is for IP protocol.
Ho provato a mettere il mac del mio pc sia in source che in destination e type 0800 ma poi non riesco ne a connettermi a internet ne al router stesso.
Allora cosa ci devo mettere in questi campi?
Secondo punto:
http://web.tiscali.it/peppeunz/3-3-11a.jpg
e il manuale dice:
Basic Rate : Select the basic rates based on the speed of wireless adapters on the WLAN (wireless local area network).
Support/TX Rate : Select the transfer rates based on the speed of wireless adapters on the WLAN (wireless local area network).
Mi conviene spuntare tutte le velocita' supportate?
E per la sezione "Dynamic Antenna Switching", di cui il manuale non parla, mi conviene tenerla su enable?
Grazie