Nero77
03-03-2006, 20:13
ho 1 disperato bisogno di aiuto sono nuovo del forum ho le ram che nn vanno in auto con la mia DFI expert se qualcuno mi uo dire come configurarle al meglio
AMD 3800 x2
DFI sli expert
DDR 500 pc 4000 KING MAX Hard Core
nn riesco a salire + di 200MHZ con le ram appena alzo il processore solo a 205 nn mi fa nemmeno il 3dmark 05
x adesso sono fermo qui e se nn overcklocco sembra che va tutto
DRAM Frequency Set............................ - 200=RAM/FSB:01/01
Command Per Clock (CPC)....................... - Enable
CAS Latency Control (Tcl)..................... - 2.5
RAS# to CAS# delay (Trcd)..................... - 3.0
Min RAS# active time (Tras)................... - 7.0
Row precharge time (Trp)...................... - 3.0
Row Cycle time (Trc).......................... - 10 Bus Clocks
Row refresh cyc time (Trfc)................... - 17 Bus Clocks
Row to Row delay (Trrd)....................... - 03 Bus Clocks
Write recovery time (Twr)..................... - 02 Bus Clocks
Write to Read delay (Twtr).................... - 02 Bus Clocks
Read to Write delay (Trwt).................... - 02 Bus Clocks
Refresh Period (Tref)......................... - 3072 Cycles
DRAM Bank Interleave.......................... - Enabled
DQS Skew Control.............................. - Auto
DQS Skew Value................................ - 0
DRAM Drive Strength........................... - Level 7
DRAM Data Drive Strength...................... - Level 2
Max Async Latency............................. - 8.0ns
DRAM Response Time............................ - Normal
Read Preamble Time............................ - 6.0ns
IdleCycle Limit............................... - 128 Cycles
Dynamic Counter............................... - Disable
R/W Queue Bypass.............................. - 16 x
Bypass Max.................................... - 07 x
32 Byte Granularity........................... - Disable(4 Bursts)
AMD 3800 x2
DFI sli expert
DDR 500 pc 4000 KING MAX Hard Core
nn riesco a salire + di 200MHZ con le ram appena alzo il processore solo a 205 nn mi fa nemmeno il 3dmark 05
x adesso sono fermo qui e se nn overcklocco sembra che va tutto
DRAM Frequency Set............................ - 200=RAM/FSB:01/01
Command Per Clock (CPC)....................... - Enable
CAS Latency Control (Tcl)..................... - 2.5
RAS# to CAS# delay (Trcd)..................... - 3.0
Min RAS# active time (Tras)................... - 7.0
Row precharge time (Trp)...................... - 3.0
Row Cycle time (Trc).......................... - 10 Bus Clocks
Row refresh cyc time (Trfc)................... - 17 Bus Clocks
Row to Row delay (Trrd)....................... - 03 Bus Clocks
Write recovery time (Twr)..................... - 02 Bus Clocks
Write to Read delay (Twtr).................... - 02 Bus Clocks
Read to Write delay (Trwt).................... - 02 Bus Clocks
Refresh Period (Tref)......................... - 3072 Cycles
DRAM Bank Interleave.......................... - Enabled
DQS Skew Control.............................. - Auto
DQS Skew Value................................ - 0
DRAM Drive Strength........................... - Level 7
DRAM Data Drive Strength...................... - Level 2
Max Async Latency............................. - 8.0ns
DRAM Response Time............................ - Normal
Read Preamble Time............................ - 6.0ns
IdleCycle Limit............................... - 128 Cycles
Dynamic Counter............................... - Disable
R/W Queue Bypass.............................. - 16 x
Bypass Max.................................... - 07 x
32 Byte Granularity........................... - Disable(4 Bursts)